Al2O3–Y3Al5O12(YAG)–ZrO2 ternary composite rapidly solidified from the eutectic melt

In situ fabrication of new ceramic eutectic composites by rapid solidification of eutectic drops is a cheap and quick method compared to fabrication of directional solidification or multi-step fabrication methods of fiber reinforced/layered composites for high temperature use. This study reports the fabrication of ceramic composites during rapid solification of eutectics melts in the ternary oxide alumina–yttria–zirconia system. Layered ternary eutectics are obtained in the alumina–YAG–zirconia subsystem. The microstructure of Al₂O₃–Y₃Al₅O₁₂–ZrO₂ composites rapidly solidified from melts is presented.     

Growth rate effect on colony formation in directional solidification of Al2O3/YAG/ZrO2

Mechanical properties of Al₂O₃/Y₃Al₅O₁₂/ZrO₂ ternary eutectic ceramics are strongly affected by structural defects as pores or colonies. Experimental investigation of the microstructure of this ternary composite indicates that the colonies are generally observed when the solidification occurs at high rates. In this work, the influence of the growth rate on the solid-liquid interface shape and formation of colonies in directional solidification of Al₂O₃/Y₃Al₅O₁₂/ZrO₂ by Bridgman, Edge-defined Film-fed Growth (EFG), and Czochralski (Cz) methods is numerically and experimentally investigated. Numerical modeling of the Bridgman growth process shows large curvatures of the solid-liquid interface when the pulling rate is increased up to 80 mm/h. The ingots solidified at rates between 5 and 80 mm/h exhibit colony type microstructure. The analysis of EFG growth of ceramic ribbons reveals less curved solid-liquid interfaces in this system. Numerical modeling shows significant increase in the interface curvature with increasing pulling rate. The microstructure of ribbons grown at pulling rates between 6 and 12 mm/h exhibits colonies only for the ingots solidified at higher rate. Simulations carried out for Czochralski growth process show that the solidification front is almost plane in this system. These results are in agreement with experimental observations showing good structural quality of Cz grown crystals with a flat solid-liquid interface. Finally it is concluded that formation of colonies in directional solidification of this ternary eutectic composite is linked to large curvatures of the growth interface.     

Microstructure and properties of directionally solidified LaB6 (100)-ZrB2 eutectic composite prepared by the optical zone melting method

Directionally solidified (DS) LaB₆ (001)-ZrB₂ eutectic composite is successfully prepared by optical zone melting technique. The effect of the solidification rate on the microstructure and properties is systemically investigated.With the increase in the solidification rate from 20 to 100 mm/h, the eutectic rods present a homogeneous eutectic microstructure. The relationship between the average eutectic spacing and the solidification rate is established. The fracture toughness shows an obvious anisotropy. Crack deflection and crack bridging play important roles in improving the fracture toughness of the material. As the solidification rate is increased from 20 to 300 mm/h, the fracture toughness, bending strength and current density firstly increase and then decrease. The highest fracture toughness of 5.16 MPa.m^1/2, bending strength of 809.04 MPa and current density of 36.24 A/cm² at 1873 K belong to the DS LaB₆ (001) - ZrB₂ eutectic composite obtained at V = 100 mm/h.     

Effect of solidification path on the microstructure of Al2O3–Y2O3–ZrO2 ternary oxide eutectic ceramic system

The solidification path of the Al₂O₃–Y₂O₃–ZrO₂ ternary oxide eutectic composite ceramic is determined by a high temperature DTA and laser floating zone (LFZ) directional solidification method to investigate the effect of solidification path on the microstructure of the ternary oxide. The DTA and microstructure analyses show that the YAG or Al₂O₃ tends to form as primary phase under the unconstrained solidification conditions, and then the system enters ternary eutectic solidification during cooling from 1950 °C at rate of 20 °C/min. The as-solidified composite ceramic shows a divorced irregular eutectic structure consisting of Al₂O₃, YAG and ZrO₂ phases with a random distribution. The primary phases are however completely restrained at the directional solidification conditions with high temperature gradient, and the ternary composite by LFZ presents well coupled eutectic growth with ultra-fine microstructure and directional array. Furthermore, the eutectic transformation and growth mechanism of the composite ceramic under different solidification conditions are discussed.     

Microstructure refinement approaches of melt-grown Al2O3/YAG/ZrO2 eutectic bulk

Microstructure developments of melt-grown Al₂O₃/YAG/ZrO₂ ceramic bulks were investigated by controlling composition, cooling rate, heterogeneous nucleation sites and melt superheating treatment. The solidification microstructure of sample with hypereutectic composition (ZrO₂ 20 mol%) is finer than that with hypoeutectic or eutectic ones. With increasing the cooling rate, microstructure of melt-grown samples develops from colony to dendrite and finally to cell. The microscopy and the components of samples vary with the melt superheating temperature and the type of heterogeneous nucleation sites. The microstructure evolutions of melt-grown Al₂O₃/YAG/ZrO₂ eutectic relate to the melt undercooling level and the solid–liquid interfaces stability.     

Microstructures and mechanical properties of directionally solidified Al2O3/GdAlO3 eutectic ceramic by laser floating zone melting with high temperature gradient

Directionally solidified Al₂O₃/GdAlO₃ eutectic ceramic rods with high densities and low solidification defects are prepared by laser floating zone melting at solidification rate from 2 to 200 μm/s. The microstructure evolution, eutectic growth behavior and mechanical properties are investigated. At low solidification rates (<30 μm/s), the eutectic rods present a homogeneous irregular eutectic microstructure, whereas cellular microstructure containing regular lamella/rod structure is developed at higher solidification rates. The relationship is established between the eutectic interphase spacing and solidification rate, which follows the Magnin-Kurz eutectic model. The Vickers hardness (15.9–17.3 GPa) increases slightly with decreasing interphase spacing, but the fracture toughness (4.08 MPa m^1/2) shows little dependence with the solidification rate. Different crack propagation mechanisms are revealed among the indentation cracks. The flexural strength at ambient temperature reaches up to 1.14 GPa for the eutectic grown at 100 μm/s. The fracture surface analysis indicates that the surface defects are the main crack source.     

Investigation of the solidification behavior of Al2O3/YAG/YSZ ceramic in situ composite with off-eutectic composition

Directionally solidified Al₂O₃/YAG/YSZ ceramic in situ composite is an interesting candidate for the manufacture of turbine blade because of its excellent mechanical property. In the present study, two directionally solidified hypoeutectic and hypereutectic Al₂O₃/YAG/YSZ ceramic in situ composites are prepared by laser zone remelting, aiming to investigate the solidification behavior of the ternary composite with off-eutectic composition under high-temperature gradient. The results show that the composition and laser scanning rate significantly influence the solidification microstructure. The ternary in situ composite presents ultra-fine microstructure, and the eutectic interspacing is refined with the increase of the scanning rate. The Al₂O₃/YAG/YSZ hypoeutectic ceramic displays an irregular hypoeutectic network structure consisting of a primary Al₂O₃/YAG binary eutectic and fine Al₂O₃/YAG/YSZ ternary eutectic. Only at low scanning rate, homogeneous ternary eutectic-like microstructures are obtained in the hypoeutectic composition. Meanwhile, the Al₂O₃/YAG/YSZ hypereutectic ceramic shows homogeneous eutectic-like microstructure in most cases and the eutectic interspacing is finer than the ternary eutectic. Furthermore, the formation and evolution mechanism of the off-eutectic microstructure of the ternary composite are discussed.     

Growth of Al2O3/ZrO2(Y2O3) eutectic rods by the laser floating zone technique: effect of the rotation

The laser floating zone technique has been applied to the growth of Al₂O₃/ZrO₂(Y₂O₃) rods in the eutectic composition to reveal the effect of forced convection induced by rotation on the rod microstructure. A systematic experimental study of this effect has been carried out combining different source rod and/or eutectic rod rotation (0–200 rpm) and travelling speeds (10–1500 mm/h) in an axial thermal gradient close to 6 × 10⁵ C/m. The results indicate that the rotation is useful to achieve a more homogeneous temperature distribution, especially in thick rods but it has a limited effect in the change of the solidification front shape. The forced convection in the floating zone caused by rotation slightly flattens the solidification interface enhancing the homogeneity of the phase distribution across the sample. However, it introduces several new microstructural features like banding and phase coarsening that can deteriorate the mechanical behaviour of the rods. On the other hand, rods above 1.6 mm in diameter cannot be grown without cracks, even with fast eutectic rod rotation. Rotation does not change the pulling rate threshold (50 mm/h) at which the transition from coupled to dendritic and cellular growth morphology takes place.     

Microstructure, growth mechanism and mechanical property of Al2O3-based eutectic ceramic in situ composites

Directionally solidified Al₂O₃-based eutectic ceramic in situ composites with inherently high melting point, low density, excellent microstructure stability, outstanding resistance to creep, corrosion and oxidation at elevated temperature, have attracted significant interest as promising candidate for high-temperature application. This paper reviews the recent research progress on Al₂O₃-based eutectic ceramic in situ composites in State Key Laboratory of Solidification Processing. Al₂O₃/YAG binary eutectic and Al₂O₃/YAG/ZrO₂ ternary eutectic ceramics are prepared by laser zone melting, electron beam floating zone melting and laser direct forming, respectively. The processing control, solidification characteristic, microstructure evolution, eutectic growth mechanism, phase interface structure, mechanical property and toughening mechanism are investigated. The high thermal gradient and cooling rate during solidification lead to the refined microstructure with minimum eutectic spacing of 100 nm. Besides the typical faceted/faceted eutectic growth manner, the faceted to non-faceted growth transition is found. The room-temperature hardness H_V and fracture toughness K_IC are measured with micro-indentation method. For Al₂O₃/YAG/ZrO₂, K_IC = 8.0 ± 2.0 MPa m^1/2 while for Al₂O₃/YAG, K_IC = 3.6 ± 0.4 MPa m^1/2. It is expectable that directionally solidified Al₂O₃-based eutectic ceramics are approaching practical application with the advancement of processing theory, technique and apparatus.     

Growth-microstructure relationship in MgO-MgAl2O4 eutectic fabricated by micro-pulling down method with MgAl2O4 seed crystals

The MgO-MgAl₂O₄ eutectic was directionally solidified via micro-pulling down method in the form of rods with 2–3 mm diameter. MgAl₂O₄ single crystals (with <111> orientation) were used as crystallization seeds. At low pulling rates, especially 0.15 mm/min triangle-like cross-section was observed, which was linked to the eutectic MgAl₂O₄ following the crystallographic direction of the seed. MgO precipitates in the form of lamellae and rods with median equivalent diameter ranging from 0.19 to 0.85 μm, depending on the pulling rate. The preferred crystallization direction was <111> for both phases, however notable traces of other directions, e.g. <100>, <110> and <331> were found as well.     

Stabilization of zirconia lamellae in rapidly solidified alumina–zirconia eutectic composites

In-situ fabrication of ceramic eutectic composites by rapid solidification of eutectic drops is a cheap and quick method compared to directional solidification or to multi-step fabrication methods of fiber reinforced/layered materials for high temperature use. Binary eutectic composites with a homogeneous periodic microstructure have been obtained by directional solidification of eutectic melts for many years, but typical solidification velocities used in directional solidification are limited to the range of cm/hour or, more recently, up to 15 mm/min. The present study aims to determine the effects of faster solidification rates on the structure of the alumina–zirconia binary composites obtained at higher growth rates by rapid solidification from eutectic melts in air or vacuum. A binary composite with zirconia stabilized in the high-temperature tetragonal form is presented. The stabilization of the tetragonal phase has not been observed before in bulk crystalline pellets of binary Al₂O₃–ZrO₂ eutectic composites.     

Microstructure of the directionally solidified ternary eutectic ceramic Al2O3/MgAl2O4/ZrO2

The directionally solidified Al₂O₃/MgAl₂O₄/ZrO₂ ternary eutectic ceramic was prepared via induction heating zone melting. Smooth Al₂O₃/MgAl₂O₄/ZrO₂ eutectic ceramic rods with diameters of 10 mm were successfully obtained. The results demonstrate that the eutectic rods consist of Al₂O₃, MgAl₂O₄ and ZrO₂ phases. In the eutectic microstructure, the MgAl₂O₄ and Al₂O₃ phases form the matrix, the ZrO₂ phase with a fibre or shuttle shape is embedded in the matrix, and a quasi-regular eutectic microstructure formed, presenting a typical in situ composite pattern. During the eutectic growth, the ZrO₂ phase grew on non-faceted phases ahead of the matrix growing on the faceted phase. The hardness and fracture toughness of the eutectic ceramics reached 12 GPa and 6.1 MPa·m ^1/2, respectively, i.e., two times and 1.7 times the values of the pre-sintered ceramic, respectively. In addition, the ZrO₂ phase in the matrix reinforced the matrix, acting as crystal whiskers to reinforce the sintered ceramic.     

Mechanical properties up to 1900 K of Al2O3/Er3Al5O12/ZrO2 eutectic ceramics grown by the laser floating zone method

Directionally solidified Al₂O₃–Er₃Al₅O₁₂–ZrO₂ eutectic rods were processed using the laser floating zone method at growth rates of 25, 350 and 750 mm/h to obtain microstructures with different domain size. The mechanical properties were investigated as a function of the processing rate. The hardness, ∼15.6 GPa, and the fracture toughness, ∼4 MPa m^1/2, obtained from Vickers indentation at room temperature were practically independent of the size of the eutectic phases. However, the flexural strength increased as the domain size decreased, reaching outstanding strength values close to 3 GPa in the samples grown at 750 mm/h. A high retention of the flexural strength was observed up to 1500 K in the materials processed at 25 and 350 mm/h, while superplastic behaviour was observed at 1700 K in the eutectic rods solidified at the highest rate of 750 mm/h.     

Competitive growth of Al2O3/YAG/ZrO2 eutectic ceramics during directional solidification: Effect of interfacial energy

The microstructure evolution and growth behavior of the Al₂O₃/Y₃Al₅O₁₂(YAG)/ZrO₂ ternary eutectic ceramics during directional solidification were well investigated. During directional solidification of the Al₂O₃/YAG/ZrO₂ ternary eutectic ceramics, {} Al₂O₃ paralleled with {001}ZrO₂ while they did not parallel with {001}YAG at the same time in the competitive growth stage. All of the interfaces parallel to each other finally. The area percentage of the Al₂O₃/ZrO₂ and YAG/ZrO₂ interfaces are 40.4 ± 0.2% and 30.8 ± 0.1%, respectively, higher than that of the Al₂O₃/YAG (28.8 ± 0.2%). The content of Al₂O₃ and YAG phases are 39.9% and 41.1%, respectively, almost double of that of ZrO₂. The interfaces of Al₂O₃/ZrO₂ and YAG/ZrO₂ are shorter and more dispersed than that of the Al₂O₃/YAG. It was found that the interfacial energy of Al₂O₃/ZrO₂ and YAG/ZrO₂ interfaces are lower than that of Al₂O₃/YAG. It can be concluded that interfacial energy plays a decisive role in affecting the crystallographic orientation and interfaces distribution in the Al₂O₃/YAG/ZrO₂ eutectic since the interfaces of Al₂O₃/ZrO₂ and YAG/ZrO₂ with lower interfacial energy can be formed more easily during directional solidification. Therefore, the contents of Al₂O₃/ZrO₂ and YAG/ZrO₂ interfaces are higher. This study can provide theoretical guidance for interface design of multi-phase materials.     

Superplastic deformation of directionally solidified nanofibrillar Al2O3–Y3Al5O12–ZrO2 eutectics

Nanofibrillar Al₂O₃–Y₃Al₅O₁₂–ZrO₂ eutectic rods were manufactured by directional solidification from the melt at high growth rates in an inert atmosphere using the laser-heated floating zone method. Under conditions of cooperative growth, the ternary eutectic presented a homogeneous microstructure, formed by bundles of single-crystal c-oriented Al₂O₃ and Y₃Al₅O₁₂ (YAG) whiskers of ≈100 nm in width with smaller Y₂O₃-doped ZrO₂ (YSZ) whiskers between them. Owing to the anisotropic fibrillar microstructure, Al₂O₃–YAG–YSZ ternary eutectics present high strength and toughness at ambient temperature while they exhibit superplastic behavior at 1600 K and above. Careful examination of the deformed samples by transmission electron microscopy did not show any evidence of dislocation activity and superplastic deformation was attributed to mass-transport by diffusion within the nanometric domains. This combination of high strength and toughness at ambient temperature together with the ability to support large deformations without failure above 1600 K is unique and shows a large potential to develop new structural materials for very high temperature structural applications.     

Microstructure and mechanical properties of Al2O3/Y3Al5O12/ZrO2 hypereutectic directionally solidified ceramic prepared by laser floating zone

Al₂O₃/Y₃Al₅O₁₂/ZrO₂ directionally solidified ceramic has been considered as a promising candidate for ultrahigh temperature structural materials due to its excellent performance even close to its melting point. In this work, laser floating zone (LFZ) solidification experiments were performed on Al₂O₃/Y₃Al₅O₁₂/ZrO₂ hypereutectic with the solidification rates between 2 μm/s and 30 μm/s. The full eutectic lamellar microstructure is obtained with hypereutectic composition. The solid/liquid interface morphology is investigated. The microstructure characteristic is discussed based on the solid/liquid interface. The variation of lamellar spacing with different compositions and solidification rates was reported and discussed by considering an irregular eutectic growth model. The maximum hardness and fracture toughness are 19.06 GPa and 3.8 MPa m^1/2, respectively. The toughening mechanism of ZrO₂ is discussed based on the scenario of the crack propagation pattern.     

Processing,microstructure and performance of Al2O3/Er3Al5O12/ZrO2 ternary eutectic ceramics prepared by laser floating zone melting with ultra-high temperature gradient

Directionally solidified Al₂O₃/Er₃Al₅O₁₂(EAG)/ZrO₂ ternary eutectic/off-eutectic composite ceramics with high density, homogeneous microstructures, well-oriented growth have been prepared by laser floating zone melting at different solidification rates from 4 to 400 µm/s. Uniform and stable melting zone is obtained by optimizing temperature field distribution to keep continuous and stable eutectic growth and prevent from cracks and defects. The as-solidified composite ceramic exhibits complexly irregular eutectic structure, in which the eutectic spacing is rapidly refined but dotted ZrO₂ number inside Al₂O₃ phase is decreased as increasing the solidification rate. The formation mechanism of ZrO₂ distributed inside Al₂O₃ matrix is revealed by examining the depression of solid/liquid interface. Furthermore, after heat exposure 1500 °C for 200 h, the eutectic microstructure only shows tiny coarsening, which indicates it has excellent microstructural stability. As increasing the ZrO₂ content, the fracture toughness can be improved up to 3.5 MPa m^1/2 at 20.6 mol% ZrO₂.     

Effect of cooling rate on the microstructure and mechanical properties of melt-grown Al2O3/YAG/ZrO2 eutectic ceramic

Melt-grown Al₂O₃/YAG/ZrO₂ ternary eutectic samples were solidified by quenching and with controlled cooling rates of 10, 50, and 250 °C/min, respectively. Effect of cooling rate on microstructure and mechanical properties were examined. With the increase of cooling rate, three classical characteristic microstructures are obtained and developed from colony structure to dendrite structure and to cell structure. In the quenching process, the sample consists of lamellar eutectic cells and its fracture toughness increases to 4.13 ± 0.8 MPa m^1/2. The microstructure transitions with the cooling rate are attributed to instability of the solid–liquid interface. In this work, the interface instability is analyzed to explain the microstructure evolutions in terms of undercooling and characteristic lengths of solute diffusion and capillarity effect.     

Effect of scanning speed on the solidification process of Al2O3/GdAlO3/ZrO2 eutectic ceramics in a single track by selective laser melting

Al₂O₃/GdAlO₃/ZrO₂ ternary eutectic ceramics with fine microstructure were directly fabricated from mixed pure ceramic powders by selective laser melting. The specimen forming quality, molten pool morphology and microstructure characteristic were investigated as functions of scanning speed. Solidification defects such as cracks and pores were effectively suppressed when the scanning speed was 12 mm/min. The relative density of the as-solidified eutectic specimens decreased from 98.7% to 95.7% with increasing the scanning speed up to 48 mm/min. The melting in this study was governed by conduction mode, leading to a decrease tendency of both melting width and depth with the increase of the scanning speed. Different from ordinary cognition, the eutectic spacing in top zone of the molten pool first decreased and then increased with increasing the scanning speed from 6 mm/min to 48 mm/min. The transition point appeared at 12 mm/min, where the dominant factor affecting the solidification rate changed from the scanning speed to the value of the angle between microstructure growth direction and laser scanning direction.