湍动流化床过渡段固含率分布特征的实验及数值模拟

在湍动流化床中,过渡段对于包括甲醇制烯烃在内的气固催化快反应有着重要的作用。采用PV6D反射型光纤探针对内径95 mm的湍动流化床内过渡段的固含率分布和脉动参数进行了测量,分别考察了表观气速和静床高的影响,并采用修正的基于颗粒动力学的三段曳力双流体模型进行模拟。实验表明,湍动流化床过渡段中固含率的轴向分布呈现S型和指数型两种类型,固含率轴向与径向分布都在过渡段内出现最大梯度,表明过渡段中固体浓度分布比稀相段和密相段更不均匀。表观气速和静床高的变化将导致S型和指数型分布的相互转变,并且对过渡段底部与壁面附近的固体高浓度区影响最为显著。局部固含率脉动概率密度分布表明,在静床高较小时,随着气速的增大,床层下部气含率最大值位置将从中心区移动至环隙区,呈现气含率的双峰型分布。本文提出的修正三段曳力模型考虑了颗粒团聚的影响,对过渡段中分布板影响区之外的固含率分布均能较好地模拟。     

粗颗粒在锥型床中的流化特性

通过Ｇｅｌｄａｒｔ－Ｄ类粗颗粒在三种锥形床中的实验表明：随着入口的表观气速的增加,在床中依次出现固定床流区,部分流化区和喷动流区。在固定床区内,压降和表观气速关系可以通过Ｅｒｇｕｎ公式求得：在部分流化床区内;实验和理论计算均表明了由于颗粒所受到的曳力档的轴向高度增加而减小,造成床层轴向上部未流化的颗粒对下部硫化颗粒膨和压制作用,在喷动流化区内,给出了预测锥形床的初始喷动气速和喷动压降的经验公式。     

一种脱油油砂颗粒流态化特性的研究

在一套直径300mm、高7000mm有机玻璃冷模实验装置上对一种脱油油砂颗粒流态化特性进行了实验研究。粒度测试结果表明该脱油油砂颗粒的粒度分布宽,细颗粒含量较多。采用FXC-Ⅱ/32型压力迅检仪测量了不同表观气速下脱油油砂颗粒沿流化床轴向平均颗粒浓度分布,采用压力梯度法测量了脱油油砂颗粒的密相床膨胀,采用容积法测量了自由空域内脱油油砂颗粒的夹带量。实验结果表明,该脱油油砂颗粒的流化性能较好;轴向平均颗粒浓度分布整体表现为下浓上稀,其中,在密相区随表观气速增加而减小,在稀相区随表观气速增加而增大;基于床高比表示的密相床膨胀随表观气速增加先增大后减小,在表观气速为0.362m·s-1时密相床最大;自由空域内的夹带量随表观气速增加而增大;建立了密相轴向平均颗粒浓度的数学模型,模型预测值与实验值吻合较好。     

方形气固流化床从鼓泡到湍动流态化转变速度预测模型

在368 mm×368 mm的方形气固流化床中对FCC颗粒进行了流态化实验,基于对床内总体压力脉动信号分析了从鼓泡流态化到湍动流态化的转变速度Uc与静床高度H0及床层面位置H的关系.结果表明,床层截面位置H较低或静床高度H0增加都使Uc增加,即鼓泡流态化到湍动流态化的流型转变是由床层上部逐渐向下扩展的递进行为.基于这一...     

气固流化床内费托铁基催化剂的流化特性

为研究费托(Fischer?Tropsch, FT)催化剂在气固流化床内的流动过程,分析了催化剂的主要物性参数,在不同直径流化床内测量了各表观气速下FT催化剂的流动特性,并与广泛应用的流化催化裂化(Fluid Catalytic Cracking, FCC)催化剂的流态化行为进行了对比。结果表明,同为A类颗粒,相较于FCC催化剂,由于FT催化剂的休止角较小(约为FCC催化剂的75%),其临界流化速度较小、床层膨胀高度和气节高度较小;两种催化剂在流化床内流化过程基本相似,随表观气速增大依次出现膨胀、鼓泡、湍动等流型,但各流型转变时的临界速度差异较大。催化剂物性参数对流化特性影响较大,FT催化剂在各阶段流化过程均相对稳定,有利于催化剂在流化床内均匀分布,其气固接触效果优于FCC催化剂;不同催化剂床层高径比下气节高度变化的转折点与流型存在对应关系,可将气节高度随表观气速的变化关系作为判断湍动流化区内流型临界速度的依据。     

水平辅助气对喷动床流动特性影响的研究

在上部内径为 195mm柱状、下部为 6 0°锥体的喷动床中水平引入辅助气 ,考察了水平辅助气对流动特性的影响。实验结果发现 ,辅助气的水平引入比竖直或法向引入可以更有效地抑制喷动气体向环流区扩散 ,降低最小喷动气速。在总气速一定的条件下 ,增大辅助气速的比例 ,可以降低喷动区空隙率而使颗粒浓度增大 ,提高颗粒的循环流动量。相比而言 ,喷动气速对喷动区颗粒的流动速度影响较大 ,而水平辅助气速对环流区颗粒的流动速度影响较大     

反应器结构对多段气化炉内颗粒分布的影响

针对多段气化炉(上部快速床、下部鼓泡床),采用MP-PIC(Multi-Phase Particle In Cell)方法模拟了多粒径煤粉颗粒的三维全循环流化过程,考察了鼓泡床与快速床床径比及鼓泡床和快速床之间的过渡段高度对气化炉内流动特性的影响。结果表明,基本工况下,大颗粒主要存在于下部鼓泡床中,细颗粒主要存在于上部快速床内,但细颗粒会通过旋风分离器和回料管再次进入鼓泡床参与循环。进入旋风分离器的大部分为半径622 ?m以下的小颗粒,无1216 ?m以上的大颗粒。旋风分离器对小颗粒的分离效率为99.75%,分离效率良好。增大床径比(即减小快速床直径),快速床中气速增大,整个气化床更快达到稳定状态,被夹带到快速床中的颗粒增多,所夹带的颗粒粒径增大。过渡段高度存在一个适当值(炉高0.6~1.0 m),升高或降低过渡段高度,快速床中颗粒浓度均增大,颗粒通量均升高,旋风分离效率降低。     

二元颗粒在气固流化床中的轴向分布特性

通过大型冷模实验测量了二元混合颗粒在流化床内沿轴向的压力分布，考察了混合颗粒截面平均浓度沿轴向的变化特点。通过分析床层压差分布的转折点，确定了密相区与稀相区的相交界面高度，根据实验结果给出了经验关联式。通过压力信号标准差分析了流化床内混合颗粒流化性能与表观气速和颗粒混合比例的关系。实验结果表明，平均颗粒浓度沿流化床轴向呈下降趋势，且在密相区中随表观气速增加而减小，在稀相区中随表观气速增大而增大。二元颗粒中大颗粒比例x_l为0.685时，密相区总平均颗粒浓度存在最大值。密相区与稀相区相交界面高度随表观气速增大而提高。当0.225≤x_l≤0.479和0.561≤u_g≤1.122 m/s时，流化床内二元颗粒的流化性能和混合程度达到最佳。     

床形结构对气固流化床流化质量和气体返混特性的影响

用实验方法比较了一个二维床和一个大型三维床内FCC颗粒流化床在鼓泡域和湍动域内的流化质量和气体返混特性。实验结果表明,床形对A类颗粒气固流化床具有非常大的影响。二维床和三维床的流动和气固混合行为既具有相似性,如床膨胀随气速的变化趋势;也具有很大的差异性,既包括三维床流化质量差、轴向气体扩散系数大等量上的不同,又包括压力脉动、轴向气体扩散系数的变化趋势以及湾流模式等质上的不同。总之,在本研究中,二维床体现的是一种具有强烈壁效应的小型流化床的特征,而三维床则体现的是静床高度具有很大影响的大型流化床的特征。     

生物质惰性颗粒混合物的混合分离特性

在D99mm×1000mm的圆柱流化床中,选用不同粒径的沙子／锯末、沙子／菜籽双组分混合物,研究了不同沉积组分含量,尤其是富沉积组分情形下床层表观气速、静床高度对流化床二组分混合物的混合与分离的影响．实验结果表明：静床高度对生物质惰性颗粒混合物分离指数无影响,沉积组分适宜的粒度及床层高和表观气速有利于生物质惰性颗粒混合物的混合．     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。