Performance simulation of a turboprop engine for basic trainer

A performance simulation program for the turboprop engine (PT6A-62), which is the power plant of the first Korean indigenous basic trainer KT-1, was developed for performance prediction, development of an EHMS (Engine Health Monitoring System) and the flight simulator. Characteristics of components including compressors, turbines, power turbines and the constant speed propeller were required for the steady state and transient performance analysis with on and off design point analysis. In most cases, these were substituted for what scaled from similar engine components’ characteristics with the scaling law. The developed program was evaluated with the performance data provided by the engine manufacturer and with analysis results of GASTURB program, which is well known for the performance simulation of gas turbines. Performance parameters such as mass flow rate, compressor pressure ratio, fuel flow rate, specific fuel consumption and turbine inlet temperature were discussed to evaluate validity of the developed program at various cases. The first case was the sea level static standard condition and other cases were considered with various altitudes, flight velocities and part loads with the range between idle and 105% rotational speed of the gas generator. In the transient analysis, the Continuity of Mass Flow Method was utilized under the condition that mass stored between components is ignored and the flow compatibility is satisfied, and the Modified Euler Method was used for integration of the surplus torque. The transient performance analysis for various fuel schedules was performed. When the fuel step increase was considered, the overshoot of the turbine inlet temperature occurred. However, in case of ramp increase of the fuel longer than step increase of the fuel, the overshoot of the turbine inlet temperature was effectively reduced.     

Analysis of compression ignition combustion in a schnurle-type gasoline engine comparison of performance between direct injection and port injection systems-

A two-stroke Schnurle-type gasoline engine was modified to enable compression-ignition in both the port fuel injection and the in-cylinder direct injection. Using the engine, examinations of compression-ignition operation and engine performance tests were carried out. The amount of the residual gas and the in-cylinder mixture conditions were controlled by varying the valve angle rate of the exhaust valve (VAR) and the injection timing for direct injection conditions. It was found that the direct injection system is superior to the port injection system in terms of exhaust gas emissions and thermal efficiency, and that almost the same operational region of compression-ignition at medium speeds and loads was attained. Some interesting combustion characteristics, such as a shorter combustion period in higher engine speed conditions, and factors for the onset of compression-ignition were also examined.     

柴油机燃烧过程的影响因素分析

本文分析了柴油机温度和压缩比、燃烧室形状、柴油机负荷、柴油机转速、燃料性质、喷油定时、供油规律和喷雾质量等因素对柴油机燃烧过程的影响规律,为正常使用和维护柴油机以及进一步提高燃油经济性提供理论依据和指导。     

An experimental study on the thermal performance of a concentric annular heat pipe

Concentric annular heat pipes (CAHP) were fabricated and tested to investigate their thermal characteristics. The CAHPs were 25.4 mm in outer diameter and 200 mm in length. The inner surface of the heat pipes was covered with screen mesh wicks and they were connected by four bridge wicks to provide liquid return path. Three different heat pipes were fabricated to observe the effect of change in diameter ratios between 2.31 and 4.23 while using the same outer tube dimensions. The major concern of this study was the transient response as well as isothermal characteristics of the heat pipe outer surface, considering the application as uniform heating device. A better performance was achieved as the diameter ratio increased. For the thermal load of 180 W, the maximum temperature difference on the outer surface in the axial direction of CAHP was 2.3°C while that of the copper block of the same outer dimension was 5.9°C. The minimum thermal resistance of the CAHP was measured to be 0.04°C/W. In regard to the transient response during start-up, the heat pipe showed almost no time lag to the heat source, while the copper block of the same outer dimensions exhibited about 25 min time lag.     

Effects of oil properties on spark-ignition gasoline engine friction

The effects of base oil, friction modifier (FM) and viscosity grade on firing engine friction are investigated in an automotive gasoline engine. Unique aspects of the study are (1) viscosity grade is maintained when synthetic and conventional base oils are compared, (2) the influence of engine operating condition on the effectiveness of base oil, FM and viscosity grade in reducing engine friction is considered, and (3) friction-relevant design details of the test engine are discussed. Results show that replacing conventional oil with synthetic oil of the same viscosity grade reduces friction, especially at high boundary friction conditions. Molybdenum dithiocarbamate (MoDTC), and to a lesser extent organic FM, also reduce friction, especially at high boundary friction conditions. Furthermore, using 5W-20 oil causes less friction than 5W-30 and 10W-40 oil at both high and low boundary friction conditions. Results are expected to hold true for engines with similar friction-relevant designs.     

小型汽油发动机性能测试台

针对1E34F型小型汽油机研制了一套发动机性能测试台。应用相位差式扭矩转速传感器和液位变送器来测量发动机的扭矩、转速、功率和油耗。并以扭矩仪作为信号处理中心,测量数据存储并显示在计算机上。该套测试台可以全面反映发动机的综合性能。     

Development of a performance prediction method for centrifugal compressor channel diffusers

A hybrid performance prediction method is proposed in the present study. A channel diffuser is divided into four subregions: vaneless space, semi-vaneless space, channel, and channel exit region. One-dimensional compressible core flow and boundary layer calculation of each region with an incidence loss model and empirical correlation of residuary pressure recovery coefficient of a channel predict the performance of diffusers. Three channel diffusers are designed and tested for validating the developed prediction method. The pressure distributions from an impeller exit to the channel diffuser exit are measured and discussed for various operating conditions from choke to nearly surge conditions. The strong non-uniform pressure distribution which is caused by impeller-diffuser interaction is obtained over the vaneless and semi-vaneless spaces. The predicted performance shows good agreement with the measured performance of diffusers at a design condition as well as at off-design conditions.     

Network analysis of an engine lubrication system

A computer program for the analysis of engine lubrication systems has been developed. A case study of a four-cylinder gasoline engine is illustrated. This paper gives the mathematical models for oil flow through a hydraulic tappet as well as those of an oil jet and plain journal bearings. The flow from an oil pump and the flow resistance through an oil filter is considered at various temperatures. In the analysis, various design guidelines are applied. The distribution of flow and pressure of an engine lubrication system is calculated, and the pressure data compared with the experimental data at a few points in the engine lubrication system. This method is helpful to design an engine lubrication system efficiently.     

Effects of various baffle designs on acoustic characteristics in combustion chamber of liquid rocket engine

Effects of various baffle designs on acoustic characteristics in combustion chamber are numerically investigated by adopting linear acoustic analysis. A hub-blade configuration with five blades is selected as a candidate baffle and five variants of baffles with various specifications are designed depending on baffle height and hub position. As damping parameters, natural-frequency shift and damping factor are considered and the damping capacity of various baffle designs is evaluated. Increase in baffle height results in more damping capacity and the hub position affects appreciably the damping of the first radial resonant mode. Depending on baffle height, two close resonant modes could be overlapped and thereby the damping factor for one resonant mode is increased exceedingly. The present procedure based on acoustic analysis is expected to be a useful tool to predict acoustic field in combustion chamber and to design the passive control devices such as baffle and acoustic resonator.     

Precise instrumentation of a diesel single-cylinder research engine

The accuracy of any empirical result is a direct consequence of the quality of experimental setup and the strict control over testing conditions. For internal combustion engines, a large number of parameters that also exhibit complex interdependence may significantly affect the engine performance. Therefore, this work describes the essentials required to establish a high-quality diesel engine research laboratory. A single-cylinder diesel engine is taken as the fundamental building block and the requirements for all essential sub-systems including fuel, intake, exhaust, coolant and exhaust gas recirculation (EGR) are laid out. The measurement and analysis of cylinder pressure, and exhaust gas sampling/conditioning requirements for emission measurement are discussed in detail. The independent control of EGR and intake boost is also highlighted. The measurement and analysis techniques are supported with empirical data from a single-cylinder diesel engine setup. The emphasis is on providing the necessary guidelines for setting up a fully-instrumented diesel engine test laboratory.     

某型发动机油封装置的国产化设计

简述了某型发动机油封设备的功用、组成、工作原理及设计改进,说明在研制过程中所使用的主要部附件的特点。     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

Measurement and simulation of fuel injection pipe pressure and study of its effect on the heat release in a direct injection diesel engine

Fuel injection pipe pressures are measured and simulated to study the effect of fuel injection system characteristies on the heat release in a direct injection diesel engine. The fuel injection simulation is based on a linear model. The governing equations are solved by the finite difference method. The measured fuel pipe pressures and the simulated fuel pipe pressures matched well to each other except for the interval when the nozzle is closing. The effects of the fuel pipe length and the nozzle opening pressure are tested. The longer fuel pipe length causes proportional retardation of the fuel injection time. The higher nozzle opening pressure results in increase of the maximum fuel pipe pressure and shorter combustion duration.     

The effect of exhaust gas recirculation (EGR) on combustion stability, engine performance and exhaust emissions in a gasoline engine

The EGR system has been widely used to reduce nitrogen oxides (NOx) emission, to improve fuel economy and suppress knock by using the characteristics of charge dilution. However, as the EGR rate at a given engine operating condition increases, the combustion instability increases. The combustion instability increases cyclic variations resulting in the deterioration of engine performance and emissions. Therefore, the optimum EGR rate should be carefully determined in order to obtain the better engine performance and emissions. An experimental study has been performed to investigate the effects of EGR on combustion stability, engine performance, NOx and the other exhaust emissions from 1. 5 liter gasoline engine. Operating conditions are selected from the test result of the high speed and high acceleration region of SFTP mode which generates more NOx and needs higher engine speed compared to FTP-75 (Federal Test Procedure) mode. Engine power, fuel consumption and exhaust emissions are measured with various EGR rate. Combustion stability is analyzed by examining the variation of indicated mean effective pressure (COV_imep) and the timings of maximum pressure (P_max) location using pressure sensor. Engine performance is analyzed by investigating engine power and maximum cylinder pressure and brake specific fuel consumption (BSFC).     

汽油机冷却水套进水口方式设计

冷却系统是汽油机正常工作的重要保证,传统方法实验方法测试冷却系统性能价格昂贵,使用受限。利用CFD软件,从速度场、表面换热系数分布、温度场三个方面对比了两种入水方式的水套冷却性能。相切式入水方式可以更好的组织冷却液的流动,减少涡流和死区的形成,从而能获得较好水套表面换热系数的分布,垂直入水方式冷却液流向比较混乱,表面换热系数分布不均,影响了其冷却性能的发挥。总体来讲,相切入水方式要优于垂直入水方式。     

Effect of water induction on the performance and exhaust emissions in a diesel engine (II)

This study was to investigate the effects of water induction through the air intake system on the characteristics of combustion and exhaust emissions in an IDI diesel engine. The fuel injection timing was also controlled to investigate a method for the simultaneous reduction of smoke and NOx when water was injected into the combustion chamber. The formation of NOx was significantly suppressed by decreasing the gas peak temperature during the initial combustion process because the water played a role as a heat sink during evaporating in the combustion chamber, while the smoke was slightly increased with increased water amount. Also, NOx emission was significantly decreased with increase in water amount. A simultaneous reduction in smoke and NOx emissions was obtained when water was injected into the combustion chamber by retarding more 2°CA of the fuel injection timing than without water injection.     

百叶窗翅片车辆散热器性能研究

通过数值模拟方法对百叶窗翅片散热器流道中流体的流动和传热性能进行研究,将数值模拟结果与文献实验关联式计算结果进行对比,验证了数值模拟方法的正确性。将百叶窗翅片散热器的翅片间距与百叶窗间距两者关联起来,分析了其比值Fp/Lp和百叶窗倾角对于百叶窗翅片流道传热和压降性能的影响。而后分析了百叶窗翅片结构参数对于百叶窗流道间流体流动效率的影响。研究表明,百叶窗翅片的传热系数和压降随着Re数的增大而增大,随着百叶窗翅片间距与百叶窗间距比值Fp/Lp的增大而减小,随着百叶窗倾角的增大而增大。流动效率随着Re数的增大而增大,随着百叶窗翅片间距与百叶窗间距比值的增大而减小,随着百叶窗倾角的增大而增大。     

An analytical study on the performance analysis of a unit-injector system of a diesel engine

A numerical algorithm is developed to analyze the performance of a Unit-injector (UI) System for a diesel engine. The fundamental theory of the algorithm is based on the continuity equation of fluid dynamics. The loss factors that should be seriously regarded on the continuity equation are the compressibility effect of liquid fuel, the wall friction loss in high-pressure fuel lines of the system, the kinetic energy loss of fuel in the system, and the leakage of fuel out of the control volume. For an evaluation of the developed simulation algorithm, the calculation results are compared with the experimental outputs provided by the Technical Research Center of Doowon Precision Industry Co. (DPICO); the maximum pressure in the plunger chamber (P _p ) and total amount of fuel injected into a cylinder per cycle (Q_f) at each operational condition. The result shows that the average error rate (%)of P _p andQ _f are 2.90% and 4.87%, respectively, in the specified operational conditions. Hence, it can be concluded that the analytical simulation algorithm developed in this study can be reasonably applied to the performance prediction of newly designed UI system.     

Investigations on the effect of measurement errors on estimated combustion and performance parameters in HCCI combustion engine

Several parameters derived from heat release analysis are used for combustion diagnostics and control in internal combustion engines. It is important to tune the input parameters used in heat release calculations, in order to get correct estimation of heat release rate. In this study, tuning of input parameters is carried out by using cumulative heat release calculations of cylinder pressure during motoring. This tuning procedure uses offline iterative processing of motoring in-cylinder pressure data. The tuned parameters obtained from this method can also be utilized for online analysis of combustion parameters. Input parameters used in these investigations are intake air temperature, intake air pressure, phasing between the acquired pressure and crank angle position, compression ratio and scaling factor of heat transfer coefficient. Effect of error in these input parameters on estimated combustion and performance parameters like IMEP, combustion phasing, combustion duration, heat release rate, and maximum mean gas temperature are evaluated. The relative importance of measurement error in input parameters and its maximum expected error in the final results is analyzed in a HCCI combustion engine. Results shows that measurement errors in phasing between pressure and crank angle position, compression ratio and inlet air pressure affect estimated combustion and performance parameters significantly.     

Changes in the mechanical properties of oil used in a gasoline engine

This study is concerned with the changes in and deterioration of the mechanical properties of oil used in a gasoline engine. The properties analysed were friction and antiwear performance, wear debris, load-carrying ability and the formation of surface films. It was found that the oil run in an engine deteriorated so as to increase the wear and friction and decrease the load-carrying ability as the running distance of oil was increased. The main cause of deterioration was related to the ability to form a protective film in the contact zone. When the film was produced by additives (sulphur), this could properly protect the surface in the contact zone undepleted from wear and friction. But as the oil deteriorated, it could not form such a film and so its protective ability on sliding surfaces diminished.