Synthesis and properties of various poly(diphenylacetylenes) containing tert-amine moieties

The polymerization of diphenylacetylene derivatives possessing tert-amine moieties, such as triphenylamine, N-substituted carbazole and indole, was examined in the presence of TaCl₅-n-Bu₄Sn (1:2) catalyst. A polymer with high molecular weight (M_w = 570 × 10³) was obtained in good yield by the polymerization of diphenylamine-containing monomer 1b, whereas the isopropylphenylamine derivative (1c) gave a polymer with relatively low molecular weight (M_w = 2.4 × 10³). The polymerization of monomer 1d containing cyclohexylphenylamine group did not proceed; however, carbazolyl- and indolyl-containing monomers also produced polymers. Poly(1b), poly(2f) and poly(4b) could be fabricated into free-standing membranes by casting toluene solutions of these polymers. The gas permeability of poly(1b) was too low to be evaluated accurately whereas poly(4b) possessing two chlorine atoms in the repeating unit showed higher gas permeability than that of poly(1b); furthermore, poly(2f) having trimethylsilyl and 3-methylindolyl groups exhibited relatively high gas permeability (). In the cyclic voltammograms of diphenylamino group-containing polymers, poly(1b) and poly(2b), the intensities of oxidation and reduction peaks decreased more than those of carbazolyl-containing poly(2a). The molar absorptivity (?) of poly(1b) at ∼700 nm increased with increasing applied voltage in the UV-vis spectrum.     

Electrochemical study of stable N-alkoxyarylaminyl radicals

The electrochemical study of N-tert-butoxy-2,4-diphenyl-6-tert-butylphenylaminyl (1a), N-tert-butoxy-2,4-bis(4-chlorophenyl)-6-tert-butylphenylaminyl (1b), N-[2-(methoxycarbonyl)-2-propyl]-2,4-diphenyl-6-tert-butylphenylaminyl (2), and N-tert-butoxy-2,4,6-tris(4-chlorophenyl)phenylaminyl radicals (3) was performed by cyclic voltammetry using acetonitrile as the solvent and Bu₄NPF₆ as the supporting electrolyte. On cathodic scan (100 mV/s), all the radicals gave chemically reversible cyclic voltammograms, and the were determined to be −1.405 V (1a), −1.310 V (2a), −1.282 V (2b), and −1.195 V (3) (versus Fc⁺/Fc), respectively. On anodic scan (100 mV/s), on the other hand, 1a, 1b and 2 showed chemically reversible cyclic voltammograms, but 3 exhibited a partially reversible couple even on a scan rate of 500 mV/s, indicating that the cation species of 3 was less stable. The determined for 1a, 1b, 2 and 3 were 0.220, 0.280, 0.318 and 0.294 V (versus Fc⁺/Fc), respectively. The electrochemical data were compared with those of thioaminyl radicals, the corresponding sulfur analogues of 1-3.     

Synthesis, electroluminescence, and photovoltaic properties of dendronized poly(p-phenylene vinylene) derivatives

Two dendronized poly(p-phenylene vinylene) (PPV) derivatives, ED-PPV and BB-PPV, have been successfully synthesized according to the Gilch route. The obtained polymers possess excellent solubility in common solvents, good thermal stability with 5% weight loss temperature of more than 340 °C. The weight-average molecular weight (M_w) and polydispersity index (PDI) of ED-PPV and BB-PPV are in the range of (1.26-2.34)×10⁵ and 1.37-1.45, respectively. Polymer light-emitting diodes (PLEDs) with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al devices were fabricated, and the PLEDs emitted green-yellow light. The turn-on voltages of the PLEDs based on ED-PPV and BB-PPV were approximately 4.3, and 4.5 V, respectively. The PLED devices of ED-PPV exhibited the maximum luminance of about 157 cd/m² at 10.5 V. Photovoltaic cells with the configuration of ITO/PEDOT:PSS/polymer:C₆₀ (1:1)/Al were also fabricated, and the energy conversion efficiency of the devices based on ED-PPV and BB-PPV was measured to be 0.58, and 0.014%, respectively, under the white light at 75 mW/cm².     

New hyperbranched polymers containing second-order nonlinear optical chromophores: Synthesis and nonlinear optical characterization

Three hyperbranched polymers (P1-P3) containing second-order nonlinear optical chromophores were synthesized by copolymerization of aromatic dialdehydes (carbazole, triphenylamine or benzene moieties) with sulfonyl-based chromophores attached with three active methylene groups, from “A₂ + B₃” approach based on simple Knoevenagel reaction. For comparison, their corresponding linear analogue polymers (P4-P6) were prepared. All the polymers are soluble in common organic solvents, and exhibit good thermal stability. The tested NLO properties of the hyperbranched polymers are better than their corresponding linear polymers, due to the three-dimensional spatial separation of the chromophores in the obtained hyperbranched polymeric structures.     

Synthesis of laterally attached side-chain liquid crystalline poly(p-phenylene vinylene) and polyfluorene derivatives for the application of polarized electroluminescence

Two series of poly(p-phenylene vinylene) and polyfluorene derivatives (PPV1-PPV4 and PF1-PF5) containing laterally attached penta(p-phenylene) mesogenes were synthesized and characterized. These polymers show nematic liquid crystalline behavior. The optical properties of the polymers were investigated by UV-vis absorption and photoluminescence spectrometers and these polymers were fabricated to form the polarized electroluminescent devices using poly(ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS) as an alignment layer. In the series of poly(p-phenylene vinylene) derivatives, polymer PPV4 offered the best EL device performance. It emitted yellow light at 588 nm at 4 V. The maximum brightness was about 1337 cd/m² at 9 V with a polarized ratio of 2.6. In another series of polyfluorene derivatives, PF4 offered the best EL device performance with the polarized ratio of 12.4 and a maximum luminescence of 1855 cd/m². In the case of polarized white light, as a consequence of blending small amount of PF4 and PF5 with a host polymer PF2, polarized ratio of up to 10.2 and a maximum brightness of 2454 cd/m² have been attained. The aligned films exhibited pronounced polarized ratio, implying that the polymers exhibit potential for linearly polarized LED application.     

Optical and electroluminescent properties of polyfluorene copolymers and their blends

Light emitting properties of several polyfluorene (PF) copolymers (P1-P4) and their blends have been investigated. Light emitting diodes were fabricated with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al. The EL peak wavelengths were 421 nm (violet), 505, 513 nm (green) and 570 nm (yellow) for PF copolymers and 510, 535 nm (green) for P1/P2 and P1/P3 blends, respectively. Förster energy transfer in the photoluminescence and electroluminescence of the polymer blends P1/P2 and P1/P3 was studied. The LED using the polymer blend P1/P2 showed a turn-on voltage of 2.5 V and a brightness of 5×10⁴ cd/m² at 7 V. The highest external quantum efficiency was observed to be 3.71% at 5 V. Upon addition of 20 wt% of the green emitter P2 to the violet emitter P1, the device efficiency increased from 1.18 to 3.71%.     

Synthesis, characterization, and high gas permeability of poly(diarylacetylene)s having fluorenyl groups

Diarylacetylenes having fluorenyl groups and other substituents (trimethylsilyl, t-butyl, bromine, fluorine) (1a-1) were polymerized with TaCl₅-n-Bu₄Sn. Monomers 1a-l produced high molecular weight polymers 2a-l (M_w 5.1 × 10⁵-1.3 × 10⁶) in 12-59% yields. All of the polymers were soluble in common organic solvents, and gave tough free-standing membranes by the solution casting method. The onset temperatures of weight loss of polymers 2a-l in air were over 400 °C, indicating considerably high thermal stability. All the polymer membranes showed high gas permeability; e.g., the oxygen permeability coefficient (PO₂) of 2a was as large as 4800 barrers. Membrane 2d possessing two fluorine atoms at meta and para positions of the phenyl ring showed the highest oxygen permeability (PO₂ = 6600 barrers) among the present polymers.     

New amphiphilic fluorescent CBABC-type pentablock copolymers containing pyrene group by two-step atom transfer radical polymerization (ATRP) and its self-assembled aggregation

A series of novel amphiphilic fluorescent CBABC-type pentablock copolymers (Py-PMMA-PEG4600-PMMA-Py) were prepared from BAB-type amphiphilic triblock copolymer (PMMA-PEG4600-PMMA) as macroinitiator with various contents of 1-(methacryloyloxyethylamino-carboxylmethyl) pyrene (PyMOI) by atom transfer radical polymerization (ATRP) in toluene using CuBr/2,2-bipyridine as catalyst system. Triblock copolymer (PMMA-PEG4600-PMMA) was prepared by ATRP and obtained from Br-PEG4600-Br as macroinitiator with methyl methacrylate in tetrahydrofuran using the same catalyst. The molecular weights of pentablock copolymers which were reinitiated by PMMA-PEG4600-PMMA macroinitiator were calculated from ¹H NMR spectra up to 42,400 gmol⁻¹. The polydispersity of pentablock copolymers obtained from GPC analysis was narrow between 1.10 and 1.38. The crystallinity of triblock copolymer (PMMA-PEG4600-PMMA) was decreased slightly with incorporating PMMA segment. Introducing the bulky pyrene substituent into pentablock copolymer, the melting temperature was not observed and all pentablock copolymers showed amorphous patterns in wide-angle X-ray scattering (WAXS) due to decrease in the degree of crystallinity of polymer chain because of disturbing regular packing. The temperatures at 10% weight loss (Td₁₀), examined by TG analysis, showed values ranging from 265 to 323 °C in nitrogen and 264 to 313 °C in air. Fluorescence spectra of Py-PMMA-PEG4600-PMMA-Py exhibited stronger excimer emission at ca. 480 nm due to the aggregations of pyrene group formed via interaction of the hydrophobic chains. The more content of PyMOI segment in pentablock copolymers can obtain the higher emission intensity ca. 480 nm. When there were higher PyMOI contents (84.9 wt% PyMOI) in pentablock copolymers, they formed larger aggregates (210 nm) in SEM micrographs. On the other hand, while increasing the concentration of the polymer solution in THF, the morphology was changed from spherical (0.1 mg/mL) to chainlike (1.0 mg/mL) aggregates.     

New host copolymers containing pendant triphenylamine and carbazole for efficient green phosphorescent OLEDs

A series of vinyl copolymers (P1-P6) containing pendant hole-transporting triphenylamine (11-88 mol%) and carbazole chromophores were synthesized by radical copolymerization to investigate the influence of triphenylamine groups upon optoelectronic properties. The copolymers were readily soluble in common organic solvents and their weight-average molecular weights (M_ws) were between 1.41 × 10⁴ and 2.24 × 10⁴. They exhibited moderate thermal stability with T_d = 402-432 °C at 5% weight loss. The emission spectra (both PL and EL) of the blends [P1-P6 with 4 wt% Ir(ppy)₃] showed dominant green emission (517 nm) attributed to Ir(ppy)₃ due to efficient energy transfer from P1-P6 to Ir(ppy)₃. The HOMO levels of P1-P6, estimated from onset oxidation potentials in cyclic voltammeter, were −5.42 to −5.18 eV, which are much higher than −5.8 eV of conventional poly(9-vinylcarbazole) (PVK) host owing to high hole-affinity of the triphenylamine groups. The optoelectronic performances of phosphorescent EL devices, using P1-P6 as hosts and Ir(ppy)₃ as dopant (ITO/PEDOT:PSS/P1-P6:Ir(ppy)₃ (4 wt%):PBD (40 wt%)/BCP/Ca/Al), were greatly improved relative to that of PVK. The best performance was obtained with P4 device, in which the maximum luminance and luminance efficiency were 11?501 cd/m² and 10.6 cd/A, respectively.     

Synthesis of new N, N-diphenylhydrazone dyes for solar cells: Effects of thiophene-derived π-conjugated bridge

Four novel D-π-A hydrazone dyes (HT, HM, HE, and HO) with an N, N-diphenylhydrazone moiety as the electron donor, different thiophene-derived π-conjugated bridges and a cyanoacrylic acid moiety as the electron acceptor have been designed and synthesized for the application in dye-sensitized solar cells. The influences of thiophene-derived bridges on the photoelectrochemical and photovoltaic performance of these hydrazone dyes were investigated. Results demonstrate that the introduction of 3,4-dialkyloxythiophene could red-shift the dye’s absorption spectrum due to the enhancement of the electron-donating ability of π-conjugated bridges. Importantly, electrochemical impedance spectroscopy analysis reveal that 3,4-dialkyloxythiophene bridge could change the charge recombination resistance at the TiO₂/dye/electrolyte interface and as a result to improve the open-circuit photovoltage. Among the four dyes, HO exhibits the maximum power conversion efficiency of 5.83% (V_oc = 0.65 V, J_sc = 12.69 mA/cm², FF = 0.707) under simulated AM 1.5 irradiation (100 mW/cm²).     

Propylene polymerisations with novel heterogeneous combination metallocene catalyst systems

Propylene was polymerised with novel combination metallocene catalyst systems prepared by an emulsion-based heterogenisation method in liquid monomer conditions. The catalyst combinations investigated were rac-dimethylsilanylbis(2-methyl-4-phenyl-1-indenyl)zirconium dichloride/rac-[ethylenebis(2-(tert-butyldimethylsiloxy)indenyl)]zirconium dichloride/methylaluminoxane (MAO) (1 + 2) and rac-dimethylsilanylbis(2-methyl-4-phenyl-1-indenyl)zirconium dichloride/rac-dimethylsilanylbis(2-isopropyl-4-[3,5-dimethylphenyl]indenyl)zirconium dichloride/MAO (1 + 3). The effects of polymerisation temperature and hydrogen on catalyst performance and polymer properties, as well as copolymerisation with hexene and ethylene were investigated. Depending on the polymerisation conditions, M_w of polypropylene varied from 144 to 286 kg/mol for 1 + 2 and from 200 to 390 kg/mol for 1 + 3. Combination 1 + 2 produced broader molecular weight distribution (MWD) than 1 + 3, and a bimodal MWD with clearly separated low- and high-M_w polymer fractions was observed with 1 + 2. The two catalyst systems showed similar hydrogen and hexene responses. Each metallocene precursor showed individual response towards the polymerisation conditions, especially polymerisation temperature, suggesting that interaction between the catalyst active sites was negligible in the studied systems.     

Two new siloxanic proton-conducting membranes: Part I. Synthesis and structural characterization

The development of stable polymer electrolytes having good proton conductivity, low cost and operating at medium temperatures represent a crucial step in the evolution of polymer electrolyte fuel cells. We describe two new siloxanic proton-conducting membranes that were synthesized through a two-stage protocol. In the first stage, a poly(methyl hydrosiloxane) precursor (P) bearing siloxane side chains with sulfonic acid groups was prepared. In the second step, the hydrolysis of pristine precursor or its derivative obtained by grafting siloxane chains on P yielded two types of membranes with the formulas {Si(CH₃)₃O[Si(CH₃)HO]_21.26[Si(CH₃)((CH₂)₃SO₃H)O]_1.8[Si(CH₃)((CH₂)₃Si(CH₃)₂O)O]₁₄Si(CH₃)₃}_n (A) and {Si(CH₃)₃O[Si(CH₃)HO]_21.26[Si(CH₃)((CH₂)₃SO₃H)O]_1.8[Si(CH₃)((CH₂)₃(Si(CH₃)₂O)_w)O]_v[Si(CH₃)((CH₂)₃Si(CH₃)₂O-)O]_14 − vSi(CH₃)₃}_n (B), with w = 20.31. Polymer membranes of A and B were prepared by means of a hot-pressing process at 80 °C and 10 t/cm². Scanning electron microscopy showed that A and B are rubbery materials with rough and transparent surfaces. Thermogravimetric investigations performed under air atmosphere disclosed that A and B are thermally stable up to at least 198 °C. DSC measurements yielded T_g(s) of −44 and −60 °C for A and B, respectively. The polymers exhibit ionic exchange capacities of 0.33 (A) and 0.15 meq/g (B). FT-IR and FT-Raman investigations revealed that the polymers consist of reticulated siloxane networks with pendant silicone chains having sulfonic acid groups.     

Synthesis and characterization of chiral polythiophenes: Poly [(R)-(−) and (S)-(+)-2-(3′-thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate]

(R)-(−) (1) and (S)-(+)-2-(3′-Thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate (2) monomers were synthesized, characterized, and polymerized in chloroform using FeCl₃ as an oxidizing agent. Molecular weights of 2.6 × 10⁴ and 3.2 × 10⁴ for poly1 and poly2, respectively, were determined by SEC analysis. FTIR spectra of the polymers indicated the coupling of monomers through the α positions. UV-vis spectra showed absorption bands at λ_max = 226 and 423 nm for poly1 and poly2, ascribed to transitions of side groups and polythiophene backbone, respectively. Poly1 and poly2 remained stable up to 210 °C. At higher temperatures, a two step weight loss degradation process was observed for both polymers by TGA analysis. ¹H NMR, in the presence of Eu(tfc)₃, and optical rotation measurements indicate the chiral properties of the monomers 1 ([α]_D²⁸ = −76.2) and 2 ([α]_D²⁸ = +76.0), and the maintenance of chirality after polymerization (poly1 [α]_D²⁸ = −29.0 and poly2 [α]_D²⁸ = +28.4, c = 2.5 in THF). According to scanning electron microscopic analysis, the polymers are highly porous.     

Effects of internal linkage groups of fluorinated diamine on the optical and dielectric properties of polyimide thin films

To investigate the difference of the trifluoromethyl (CF₃) group and ether group affecting the optical property of fluorinated polyimides (PIs), we prepared 4,4′-bis(4-amino-2-trifluoromethylphenoxy)diphenyl ether (4) with three ether groups and 2,2-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]hexafluoropropane (5) with four CF₃ groups with 2-chloro-5-nitrobenzotrifluoride and 4,4′-dihydroxydiphenyl ether or 2,2-bis(4-hydroxyphenol)hexafluoropropane. Two series of organosoluble and light-colored PIs (4a-4c, 5a-5c) were synthesized from 4 and 5 with various aromatic dianhydrides: 3,3,4,4-benzophenonetetracarboxylic dianhydride (BTDA) (a), 4,4-oxydiphthalic anhydride (ODPA) (b), and 4,4-hexafluoroisopropylidenediphthalic anhydride (6FDA) (c), prepared through a typical two-step polymerization method. These PIs were soluble in amide polar solvents and even in less polar solvents. The glass-transition temperatures (T_g) of 4a-5c were 221-249 °C and the 10% weight-loss temperatures were above 530 °C. Their films had cutoff wavelengths between 339 and 399 nm and yellowness index ranges from 1.95 to 42.60. The dielectric constants estimated from the average refractive indices are 2.59-2.93 (1 MHz). In a comparison of the PI series based on 4, 5, and 4,4′-bis(4-amino-2-trifluoromethylphenoxy)biphenyl (6), we found that the CF₃ group and ether group on the diamine had almost same effect in lowering the color, but the ether group had better thermal stability. The color intensity of the three PI series was lowered in the following order: 6 > 4 > 5. The PI 5c, synthesized from diamine 5 and dianhydride c, had six CF₃ groups in a repeated segment and ether group at the same time, so it exhibited the lightest color among the three series.     

Synthesis of poly(1-β-naphthyl-2-phenylacetylene) membranes through desilylation and their properties

The polymerization of 1-β-naphthyl-2-[(p-trimethylsilyl)phenyl]acetylene (8a) with TaCl₅-n-Bu₄Sn in cyclohexane provided a high molecular weight polymer (9a) (M_w=3.4×10⁶). The corresponding monomers having p-dimethyl-t-butylsilyl and p-dimethyl(10-pinanyl)silyl groups in place of p-trimethylsilyl group in 8a also polymerized in a similar way to give high molecular weight polymers (9b, 9c, respectively; M_w>1×10⁶). All these polymers were soluble in many common solvents such as toluene and chloroform, and provided free-standing membranes by casting from toluene solution. The oxygen permeability coefficients (P_O2) of 9a at 25 °C was as high as 3500 barrers. The membrane of poly(1-β-naphthyl-2-phenylacetylene) (10a) was prepared by desilylation of the membrane of 9a with trifluoroacetic acid. Polymer 10a was insoluble in any solvents, and showed high thermal stability (the onset temperature of weight loss in air ∼470 °C). The P_O2 value of 10a reached 4300 barrers. Not only the membrane of 9c but also its desilylation product 10c exhibited large optical rotations ([α]_D=+2924 and +9800°, respectively) and strong CD signals. This indicates that the membrane of 10c maintains the helical main chain conformation of 9c with a large excess one-handed helix sense.     

Synthesis of polystyrene microgel with glucose as hydrophilic segment via controlled free-radical polymerization

4-Vinylbenzyl glucoside peracetate (1) was copolymerized with divinylbenzene (DVB) using 1-phenyl-1-(2′,2′,6′,6′-tetramethyl-1′-piperidinyloxy)ethane (2) as an initiator in m-xylene at 138 °C for 20 h ([DVB]/[2]=28; [DVB]=0.62 mol L⁻¹). The copolymerizations were performed using the mole fraction of 1 in the total feed of 1 and DVB (F₁: [1]/[1]+[DVB]) ranging from 0.11 to 0.38 that produced the polystyrene (PSt) microgel with acetyl glucose, 3, in 46-53% yields. Dynamic laser light scattering (DLS) measurements showed that 3 was stably suspended in toluene as particles with average diameters (d's) ranging from 12 to 22 nm. A static laser light scattering (SLS) measurement gave the average molar mass, M_w,SLS, of 3 that ranged from 9.69×10⁴ to 6.96×10⁵. The numbers of the 1, 2, and DVB units in 3 (N₁, N₂, and N_DVB, respectively) were from 111 to 238, from 17 to 208, and from 350 to 4510, respectively. The deacetylation of 3 was achieved by treatment with sodium methoxide in dry 1,4-dioxane to produce the PSt microgel with glucose as the hydrophilic segment, 4. The solubilities of 4 in toluene, CHCl₃, THF, 1,4-dioxane, pyridine, DMF, DMSO, and H₂O, and the mixture of H₂O and 1,4-dioxane were examined, indicating that a hydrophilic property had been effectively introduced into 4.     

Highly efficient electroluminescent biphenylyl-substituted poly(p-phenylenevinylene)s through fine tuning the polymer structure

A series of novel biphenylyl-substituted PPV derivatives, polymers 1-4, with different substitution patterns, has been synthesized and characterized. These polymers possess excellent solubilities, good thermal stabilities, and high-photoluminescent efficiencies. ¹H NMR measurements indicated that the polymers contain negligible tolane-bisbenzyl (TBB) structural defects. Light-emitting diodes fabricated from the four polymers with the configuration of ITO/PEDOT:PSS (50 nm)/polymer (80 nm)/LiF (0.4 nm)/Ca (20 nm)/Ag emitted a saturated green light and demonstrated maximum current efficiencies of 5.1, 4.5, 4.7, and 1.4 cd/A for polymers 1-4, respectively. The much higher current efficiencies of polymers 1-3 than polymer 4 are ascribed to more balanced charge transport in the polymer layers of the three polymers, which has been confirmed by time of flight (TOF) charge mobility measurement. The hole mobilities of the polymers at the applied electric field of 2.0×10⁵ V/cm are 4.70×10⁻⁶, 3.83×10⁻⁶, 7.21×10⁻⁶, and 1.76×10⁻⁵ cm²/Vs for polymers 1-4. This research indicated that fine tuning the substitution pattern of the polymer side chains is an effective way to optimize the LED device performance by controlling the structural defects as well as balancing the charge mobility of the polymers.     

New light-emitting hyperbranched polymers prepared from tribromoaryls and 9,9-dihexylfluorene-2,7-bis(trimethyleneborate)

Three new hyperbranched polymers (P1-P3) were prepared by copolymerization of tribromoaryl moieties (triphenylamine, carbazole and fluorene moieties) with 9,9-dihexylfluorene-2,7-bis(trimethyleneborate) from “A₂ + B₃” approach based on Suzuki polycondensation reaction. They are soluble in common organic solvents, and exhibit good thermal stable luminescence. Interestingly, unlike most of fluorene-containing polymeric materials, P3 emits strong green light due to its special structure. Double-layer devices with configurations ITO/PEDOT/Polymer (50 nm)/TPBI(50 nm)/LiF(0.5 nm)/Al(80 nm) were fabricated and emitted blue or green light, with maximum luminance in the range of 25-142 cd/m² and the current efficiency up to 0.18 cd/A.     

Encapsulation-release property of amphiphilic hyperbranched d-glucan as a unimolecular reverse micelle

The synthesis of a novel unimolecular reverse micelle, the hyperbranched d-glucan carbamate (3), was accomplished through the carbamation reaction of the hyperbranched d-glucan (1) with the N-carbonyl l-leucine ethyl ester (2) in pyridine at 100 °C. Polymer 3 was soluble in a large variety of organic solvents, such as methanol, acetone, chloroform, and ethyl acetate, and insoluble in water, which remarkably differed from the solubility of 1. The degree of carbamate substitution (DS) for 3 was controlled by the feed rate of 2, and the DS values were in the range of 46.0-93.7%. Polymer 3 possessed the encapsulation ability for water-soluble molecules, such as rose bengal, thymol blue, and alizarin yellow in chloroform, and the encapsulation ability depended on the hydrophilicity of 3 and the molecular size of the dye. The rose bengal (RB) encapsulated polymer (RB/3) showed a slow release from the RB/3 system into water at neutral pH, while the release rate was significantly accelerated by the hydrolysis of the hydrophobic polymer shell under basic conditions.     

Thermally cross-linkable hyperbranched polymers containing triphenylamine moieties: Synthesis, curing and application in light-emitting diodes

This paper demonstrates synthesis of hyperbranched polymers (HTP and HTPOCH₃), containing triphenylamine moieties in main chain and thermally cross-linkable periphery or terminal vinyl groups, and application as hole-transporting layer (HTL) in multilayer light-emitting diodes. Absorption and photoluminescence (PL) spectroscopy, cyclic voltammetry (CV) and differential scanning calorimetry (DSC) were employed to investigate their photophysical, electrochemical properties and thermal curing behaviors, respectively. The hyperbranched HTP and HTPOCH₃ were readily cross-linked by heating scan, with the exothermic peaks being at 221 and 210 °C respectively. The glass-transition temperatures (T_g) of the hyperbranched polymers were higher than 140 °C after thermal cross-linking at 210 °C for 30 min. Multilayer light-emitting diodes (ITO/PEDOT:PSS/HTL/MEH-PPV/Ca/Al), using HTP and HTPOCH₃ as HTL, were readily fabricated by successive spin-coating. The performance of MEH-PPV device (maximum luminance: 9310 cd/m², luminance efficiency: 0.26 cd/A) was effectively enhanced by inserting the thermally cross-linked HTP or HTPOCH₃ as HTL (HTP: 12610 cd/m², 0.32 cd/A; HTPOCH₃: 14060 cd/m², 0.33 cd/A). This indicates that these thermally cross-linkable hyperbranched HTP and HTPOCH₃ are very suitable for the fabrication of multilayer PLEDs using solution processes.