Electrochromic properties of porous NiO thin film as a counter electrode for NiO/WO3 complementary electrochromic window

Highly porous nickel oxide (NiO) thin films were prepared on ITO glass by chemical bath deposition (CBD) method. SEM results show that the as-deposited NiO film is constructed by many interconnected nanoflakes with a thickness of about 20 nm. The electrochromic properties of the NiO film were investigated in a nonaqueous LiClO₄–PC electrolyte by means of optical transmittance, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements. The NiO film exhibits a noticeable electrochromic performance with a variation of transmittance up to 38.6% at 550 nm. The CV and EIS measurements reveal that the NiO film has high electrochemical reaction activity and reversibility due to its highly porous structure. The electrochromic (EC) window based on complementary WO₃/NiO structure shows an optical modulation of 83.7% at 550 nm, much higher than that of single WO₃ film (65.5% at 550 nm). The response time of the EC widow is found to be about 1.76 s for coloration and 1.54 s for bleaching, respectively. These advantages such as large optical modulation, fast switch speed and excellent cycle durability make it attractive for a practical application.     

Morphology effect on the electrochromic and electrochemical performances of NiO thin films

NiO thin films on ITO substrate were prepared by chemical bath deposition (CBD) and sol–gel method, respectively. The microstructure and morphology of the NiO films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Both the films have polycrystalline cubic NiO, but have distinct morphology. The CBD NiO thin film with a highly porous structure exhibited a noticeable electrochromic performance. The variation of transmittance was high up to 82% at 550 nm and the coloration efficiency (CE) was calculated to be 42 cm² C⁻¹. The sol–gel NiO thin film with a smoothly compact structure presented 35% and 28 cm² C⁻¹ at 550 nm, respectively. The electrochemical properties of both the NiO thin films were investigated in 1 M KOH electrolyte by means of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements. The CV and EIS measurements revealed that the CBD NiO thin film had better electrochemical reversibility, higher reactivity and reaction kinetics due to its highly porous structure.     

Effect of Ar/O2 ratio on double-sided electrochromic glass performance

This paper reports the qualities of WO₃ film and NiO film added to a counter electrode and their use in a double-sided electrochromic glass device. A mixture of argon and oxygen gasses with ratios of Ar/O₂ of 1.5, 2, 3, and 5 were used for the deposition of the working electrode of WO₃ film for EC glass. The structure of double-side EC glass consists of glass/ITO/NiO/electrolyte/WO₃/ITO/glass/ITO/WO₃/electrolyte/NiO/ITO/glass layers. The working electrode of WO₃ film controls the color presented, the applied voltage controls the color depth, and the counter electrode controls the transparency in the bleached state. The double-sided EC glass with double WO₃ films and double NiO films have faster coloration/bleaching rates than do single-sided EC glass. A mixture of Ar/O₂ ratio of 3.0 has the best coloration/bleaching property of the ratios tested. Compared to the single-sided EC glass, the double-sided EC glass has lower transmittance of about 72% and 6% than the 78% and 12% during coloration and bleaching states in the visible light region with +1.5 V and ?3.5 V applied.     

Poly(dopamine) assisted deposition of adherent PPy film on Ti substrate

This study aims to address an issue to a subject that is still less present in literature: the adherence of polypyrrole (PPy) films on bioinert substrate. The poly(dopamine) (PDA) assisted deposition of PPy film on titanium substrate was performed in two steps. The chemical self-polymerization of dopamine was performed as a preliminary step from dopamine in Tris buffer solution on titanium substrate. Then, the resulted poly(dopamine) layer consisting of anchors with strong interactions with Ti surface was a new suitable substrate for polypyrrole film electrochemical deposition. The new PDA–PPy films were characterized in terms of interest properties for the desired biomedical applications: adherence, electrochemical stability of PDA–PPy film, wettability, topography, morphology and antibacterial effect. The poly(dopamine) assisted deposition of PPy film has been shown to be a facile and efficient route to improve the adhesion of PPy film on titanium maintaining or improving the properties of polymeric film.     

Spin coated versus dip coated electrochromic tungsten oxide films: Structure, morphology, optical and electrochemical properties

A sol-gel derived acetylated peroxotungstic acid sol encompassing 4 wt.% of oxalic acid dihydrate (OAD) has been employed for the deposition of tungsten oxide (WO₃) films by spin coating and dip coating techniques, in view of smart window applications. The morphological and structural evolution of the as-deposited spin and dip coated films as a function of annealing temperature (250 and 500 °C) has been examined and compared by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD). A conspicuous feature of the dip coated film (annealed at 250 °C) is that its electrochromic and electrochemical properties ameliorate with cycling without degradation in contrast to the spin coated film for which these properties deteriorate under repetitive cycling. A comparative study of spin and dip coated nanostructured thin films (annealed at 250 °C) revealed a superior performance for the cycled dip coated film in terms of higher transmission modulation and coloration efficiency in solar and photopic regions, faster switching speed, higher electrochemical activity as well as charge storage capacity. While the dip coated film could endure 2500 color-bleach cycles, the spin coated film could sustain only a 1000 cycles. The better cycling stability of the dip coated film which is a repercussion of a balance between optimal water content, porosity and grain size hints at its potential for electrochromic window applications.     

Lithiation study of molybdenum oxide thin films: application to an electrochromic system

The lithiation behaviour of sputtered molybdenum oxide thin films is reported. Results indicate that such films prepared and dry lithiated under certain conditions undergo reversible lithium insertion without exhibiting a significant optical property change in the solar spectral range. Hence, such films have potential for use in electrochromic (EC) systems as counter electrodes for lithium ion storage. An all-solid EC system was fabricated and studied for its optical switching behaviour using an amorphous tungsten oxide film as the base EC layer. Encouraging results were found relative to the application of such MoO₃ films for lithium ion storage.     

Effect of post annealing treatment on electrochromic properties of spray deposited niobium oxide thin films

Niobium oxide thin films were deposited on the glass and fluorine doped tin oxide (FTO) coated glass substrates using simple and inexpensive spray pyrolysis technique. During deposition of the films various process parameters like nozzle to substrate distance, spray rate, concentration of sprayed solution were optimized to obtain well adherent and transparent films. The films prepared were further annealed and effect of post annealing on the structural, morphological, optical and electrochromic properties was studied. Structural and morphological characterizations of the films were carried out using scanning electron microscopy, atomic force microscopy and X-ray diffraction techniques. Electrochemical properties of the niobium oxide thin films were studied by using cyclic-voltammetry, chronoamperometry and chronocoulometry.     

Synthesis,Electrical Properties and Stability of Polypyrrole-Containing Conducting Polymer Composites

Conducting polymer composites of polyethylene and polypyrrole (PE/PPy), polypropylene and polypyrrole (PP/PPy) and poly(methyl methacrylate) and polypyrrole (PPMA/PPy) were prepared by means of a chemical modification method resulting in a network-like structure of polypyrrole embedded in the insulating polymer matrix. The content of polypyrrole determined by elemental analysis varied from 0·25 to 17wt%. Electrical conductivity of compression-moulded samples depended on the concentration of polypyrrole and reached values from 1×10^-11 to 1 S cm^-1. The morphology of the composites and blends was studied by low-voltage scanning electron microscopy. The stability of PP/PPy composites was investigated by thermogravimetric analysis and by conductivity measurements during heating–cooling cycles. There was only a small drop in conductivity caused by the annealing of PP/PPy composites in air at temperatures up to 80°C. The results of thermogravimetric analysis showed a stabilizing effect of PPy on PMMA/PPy composites against thermal degradation. The antistatic properties of PMMA/PPy composites were demonstrated. © 1997 SCI.     

Developing high-transmittance heterojunction diodes based on NiO/TZO bilayer thin films

In this study, radio frequency magnetron sputtering was used to deposit nickel oxide thin films (NiO, deposition power of 100 W) and titanium-doped zinc oxide thin films (TZO, varying deposition powers) on glass substrates to form p(NiO)-n(TZO) heterojunction diodes with high transmittance. The structural, optical, and electrical properties of the TZO and NiO thin films and NiO/TZO heterojunction devices were investigated with scanning electron microscopy, X-ray diffraction (XRD) patterns, UV-visible spectroscopy, Hall effect analysis, and current-voltage (I-V) analysis. XRD analysis showed that only the (111) diffraction peak of NiO and the (002) and (004) diffraction peaks of TZO were observable in the NiO/TZO heterojunction devices, indicating that the TZO thin films showed a good c-axis orientation perpendicular to the glass substrates. When the sputtering deposition power for the TZO thin films was 100, 125, and 150 W, the I-V characteristics confirmed that a p-n junction characteristic was successfully formed in the NiO/TZO heterojunction devices. We show that the NiO/TZO heterojunction diode was dominated by the space-charge limited current theory.     

Heat treatment of amorphous electrochromic WO3 thin films deposited onto indium-tin oxide substrates

Electrochromic tungsten oxide thin films, obtained by vacuum evaporation, were studied before and after heat treatment between 25 and 250°C for 2 h in air. Electrochromic properties were investigated in acid electrolyte by simultaneous measurements of the electrical and optical parameters. A.c. complex impedance techniques and voltammetry were used to characterize the films from an electrical point of view. We observed an enhancement of the electrochromic response times during both coloration and bleaching after heat treatment carried out between 150 and 220°C. This phenomenon was associated with a decrease of the ohmic drop in the electrode and a continuous variation of the impedance diagrams of these electrochromic electrodes. Moreover, we observed that the diffusion coefficient of H⁺ ions into WO₃, obtained on colored thin films, increased as the electrochromic kinetics increased.     

CuBr2‐induced charge screening on photoactive nanocolloidal polypyrrole:poly(styrene sulfonate) composite multilayer thin‐film counter electrodes for high‐efficiency dye‐sensitized solar cells

Nanocolloidal polypyrrole (PPy):poly(styrene sulfonate) (PSS) particles were synthesized by chemical oxidative polymerization using 15 wt% of PSS. The highly processable polymer composite (PPy:PSS) was spin‐coated at 4000 rpm on fluorine‐doped tin oxide glass and subsequently employed as a counter electrode (CE) for dye‐sensitized solar cells (DSCs). PPy:PSS multilayer (one, three, five) CEs were treated with CuBr₂ salt, which enhances the efficiency of the DSCs. Optical studies reveal that a bulkier counterion hinders interchain interactions of PPy which on salt treatment shows a moderate redshift in absorption maxima. Salt‐treated PPy:PSS films exhibit lower charge transfer resistance, higher surface roughness and better catalytic performance for the reduction of I₃^?, when compared with untreated films. The improved catalytic performance of salt‐treated PPy:PSS multilayer films is attributed to charge screening and conformational change of PPy, along with the removal of excess PSS. Under standard AM 1.5 sunlight illumination, salt treatment is shown to boost the efficiency of multilayer PPy:PSS composite film‐based DSCs, leading to enhanced power conversion efficiency of 6.18, 6.33 and 6.37% for one, three and five layers, respectively. These values are significantly higher (ca 50%) than those for corresponding devices without CuBr₂ salt treatment (3.48, 2.90 and 2.01%, respectively). © 2016 Society of Chemical Industry     

Electrochromic degradation in nickel oxide thin film: A self-discharge and dissolution phenomenon

Nickel oxide thin films known as optical active counter electrode in electrochromic devices were grown by Pulsed Laser Deposition (PLD) at room temperature (RT) under a 10⁻¹ mbar oxygen pressure. From intense electrochemical characterizations of as-deposited NiO electrodes in alkaline medium, a mechanism taking into account the three typical steps of their cycling life, namely the activation period, the steady state and the degradation period, is proposed. The reversible color change from transparent to brownish, generally ascribed to the Ni(II)/Ni(III) couple in the literature, was clearly identified to the electrochemically active nickel hydroxide/oxy-hydroxide phases. The reason lies in a spontaneous chemical conversion of NiO into Ni(OH)₂ when the film is immersed in KOH medium. Afterwards, once cycling is performed, there is in competition with the electrochemical process, a self-discharge phenomenon associated to a partial dissolution of the thin-film oxidized phases. This second process becomes predominant on cycling leading to a progressive degradation of the electrochromic performances.     

Sheet resistance dependence of fluorine-doped tin oxide films for high-performance electrochromic devices

In the present study, we fabricated fluorine-doped tin oxide (FTO) films with different sheet resistances (~10?Ω/□, ~6?Ω/□, and ~3?Ω/□) prepared through the adjustment of deposition time during the horizontal ultrasonic spray pyrolysis deposition (HUSPD) and investigated the effect of electrochromic (EC) performances with different sheet resistances of the FTO films used as transparent conducting electrodes. The results demonstrated that, owing to the increased electrochemical activity, the decrease of sheet resistance accelerated switching speeds of the EC devices. However, for the coloration efficiency (CE), the FTO films with the optimum sheet resistance of ~6?Ω/□ exhibited the highest value as compared to the other samples. The improvement of the CE value can be mainly attributed to high transmittance modulation by the uniform surface morphology of the FTO films to reduce interfacial light-scattering between the WO₃ films and FTO films. Therefore, our results provide a valuable insight into the improvement of the performance of the EC devices using the optimum sheet resistance (~6?Ω/□) of the FTO films.     

Potentiostatically deposited polypyrrole/graphene decorated nano-manganese oxide ternary film for supercapacitors

A simple method based on potentiostatic polymerization was developed for the preparation of ternary manganese oxide-based nanocomposite films. The ternary nanocomposites, which were characterized using x-ray diffraction spectroscopy and x-ray photoelectron spectroscopy, showed that the manganese oxide within the film consisted of MnO₂ and Mn₂O₃. Electrochemical measurements showed that the ternary nanocomposite electrode exhibited high specific capacitance (up to 320.6 F/g), which was attributed to the morphology of a polypyrrole/graphene/manganese-oxide (PPy/GR/MnO_x) ternary nanocomposite. The experimental approach maximized the pseudocapacitive contribution from redox-active manganese oxide (MnO_x) and polypyrrole (PPy), as well as the electrochemical double layer capacitive (EDLC) characteristic from graphene (GR) sheets. Long cyclic measurements indicated that the specific capacitance of the ternary nanocomposite film could retain 93% of its initial value over 1000 charge/discharge cycles, in the potential range of −0.2 to 0.7 V versus silver/silver chloride electrode (Ag/AgCl).     

基于WO3-MoO3和TiO2/CdS复合电极的光电致变色器件

电致变色广泛应用于智能窗领域,但电致变色材料仍需外部电源驱动,将太阳能电池与电致变色材料结合起来的光电致变色器件可实现无需外部供电的智能变色调控。性能优异的变色阴极和光阳极是当下光电致变色器件的研究热点。通过水热法制备WO₃-MoO₃薄膜,研究其电致变色性能;通过水热法结合连续离子层沉积法制备TiO₂/CdS复合薄膜,研究其光电转换性能。最后将WO₃-MoO₃薄膜和TiO₂/CdS复合薄膜分别作为光电致变色器件的变色阴极、光阳极构建WO₃/MoO₃-TiO₂/CdS光电致变色器件。WO₃/MoO₃-TiO₂/CdS光电致变色器件具有较大的光学调制范围(630nm处为41.99%)、更高的着色效率(35.787%),将其作为智能窗应用在现代建筑、通行工具等领域具有重要应用价值。     

Pseudocapacitive contributions to electrochemical kinetics in NiOx electrochromic anodes

Because of its ability to change optical absorption dynamically by applied electric field, nickel oxide (NiO) is a promising anodic material in smart windows, which can improve energy conversion efficiency in construction buildings. Although many works have achieved high electrochromic performance with different method. The underlying mechanism is still not fully investigated. In this article, we prepared the NiO films with large specific surface area and high stability by electron beam evaporation. X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed to figure out the surface morphology and composition of as-deposited films. Afterwards, the electrochemical properties and optical performance of the prepared NiO films were investigated. On this basis, the origin of surface charge was fully analyzed by cyclic voltammetry and diffusion coefficient test. These experimental and theoretical results firmly confirm that both the surface reaction and capacitive effect bring about the excellent EC performance in NiO films. These results not only provide clear evidence about electrochemical kinetics in NiO films, but also offer some useful guidelines for the design of EC materials with higher performance and longer stability.     

Electrochromic properties of polyaniline thin film nanostructures derived from solutions of ionic liquid/polyethylene glycol

By exploiting the templating ability, wetting properties and the capability of the ionic liquid, 1-ethyl,3-methylimidazolium bromide to furnish the anionic dopant, nanostructured thin films of polyaniline (PANI) have been fabricated from an aqueous solution of the monomer encompassing this organic moiety by electropolymerization. These films have been compared to films synthesized from a medium based on a conventional polymeric surfactant, polyethylene glycol 400 (PEG). The template/dopant controls pore structure and assembly patterns as an interconnected network of nanofibrils of 50-500 nm in length and 10-40 nm in diameter constitutes the PANI films derived from the ionic liquid-based solution whereas the dominant microstructural attribute of the PANI films obtained from the PEG-containing formulation are abutting nanoparticles with elongated shapes. The effect of the different thin film nanostructures on their electrochromic properties is evident from the higher coloration efficiency, transmission modulation (in the NIR region), larger charge capacity, enhanced cycling stablity and faster color-bleach rates observed for the PANI films obtained from the ionic liquid medium as compared to that shown by the PANI films fabricated from the PEG solution. The outstanding optical and electrochemical behavior of the films, in particular, for the film derived from the ionic liquid-based solutions indicate that such recyclable and environmentally benign reaction media are most useful especially for transposing PANI films to large area substrates for electrochromic window applications.     

In situ sol–gel synthesis of tungsten trioxide networks in polymer electrolyte: Dual-functional solid state chromogenic smart film

The novel electro-photochromic solid electrolyte films were successfully synthesized by in situ sol–gel synthesis of tungsten trioxide (WO₃) working electrode within gelatin/lithium cosolvent system. The transparent free-standing single-layer film with adhesiveness and flexibility, darken significantly under the UV radiation with photo-response time of 30 s and gradually reversed once the source of UV was blocked. Moreover, casted film on the indium tin oxide (ITO) glass showed electrochromic (EC) behavior as well in presence of ion storage counter electrode. X-ray diffraction analysis indicates the amorphous nature of an in situ synthesized gelatin-based film. The prepared film containing 30 wt% LiClO₄ and 10 wt% WO₃ (sample designated as GLi30W10) shows ionic conductivity value of 1.1 × 10⁻⁴ S/cm. The EC performances of the device with the following configuration; ITO/GLi30W10/NiO/ITO, was investigated by means of UV and cyclic voltammograms. Good performances and fast electro-response times (2 s/1 s) of the device were demonstrated with coloration efficiency of 51.54 cm²/C.     

An efficient route to a porous NiO/reduced graphene oxide hybrid film with highly improved electrochromic properties

A porous NiO/RGO hybrid film is prepared by the combination of electrophoretic deposition and chemical-bath deposition. The porous hybrid film exhibits a noticeable electrochromism with reversible color changes from transparent to dark brown, and shows high coloration efficiency (76 cm(2) C(-1)), fast switching speed (7.2 s and 6.7 s) and better cycling performance compared with the porous NiO thin film. The enhancement of electrochromic performances are attributed to the reinforcement of the electrochemical activity of the RGO sheets and the greater amount of open space in the porous hybrid film which allows the electrolyte to penetrate and shorten the proton diffusion paths within the bulk of NiO.     

All-Printed Multilayers and Blends of Poly(dioxythiophene) Derivatives Patterned into Flexible Electrochromic Displays

Low-cost, flexible and thin display technology is becoming an interesting field of research as it can accompany the wide range of sensors being developed. Here, the synthesis of poly(dimethylpropylene-dioxythiophene) (PProDOT-Me₂) by combining vapor phase polymerization and screen printing is presented. A multilayer architecture using poly(3,4-ethylenedioxythiophene) (PEDOT) and PProDOT-Me₂ to allow for electrochromic switching of PProDOT-Me₂, thereby eliminating the need for a supporting transparent conductive (metal oxide) layer is introduced. Furthermore, the technology is adapted to a blended architecture, which removes the additional processing steps and results in improved color contrast (∆E* > 25). This blend architecture is extended to other conductive polymers, such as PEDOT and polypyrrole (PPy), to highlight the ability of the technique to adjust the color of all-printed electrochromic displays. As a result, a green color is obtained when combining the blue and yellow states of PEDOT and PPy, respectively. This technology has the potential to pave the way for all-printed multicolored electrochromic displays for further utilization in printed electronic systems in various Internet of Things applications.