Rapid formation of high-quality self-assembled monolayers of dodecanethiol on polycrystalline gold under ultrasonic irradiation

Self-assembled monolayers of dodecanethiol (C₁₂SH-SAMs) on polycrystalline gold were prepared under ultrasonic irradiation at 100 W (the actual ultrasonic power intensity is about 0.1 W cm⁻² including the heat loss) for different time and investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). CV experiments show that the differential capacitance C_d values of the C₁₂SH-SAM prepared under ultrasonic irradiation at 100 W (0.1 W cm⁻²) for 15 min are independent of the scan rate, the thickness d value of this monolayer is 17.5 Å, the tilt angle φ value of the molecules in this monolayer from the gold surface normal was calculated to be 30° and the difference value of the current density at −0.2 and 0.5 V (Δi_p) is only 0.69 μA cm⁻². From the EIS experiments, we find that the phase angle value at 1 Hz Φ_1 Hz of the C₁₂SH-SAM prepared under ultrasonic irradiation at 100 W (0.1 W cm⁻²) for 15 min is 89°, the charge transfer resistance R_ct value of this monolayer is 1.40 × 10⁶ Ω cm² and the surface coverage θ value of this monolayer was calculated to be 99.997% from R_ct. These results indicate that the C₁₂SH-SAM of almost defect-free structure and very low ionic permeability can be formed under ultrasonic irradiation at 100 W (0.1 W cm⁻²) in a short time (15 min).     

Tetracarboxylic acid cobalt phthalocyanine SAM on gold: Potential applications as amperometric sensor for H2O2 and fabrication of glucose biosensor

This report describes the applications of cobalt tetracarboxylic acid phthalocyanine (CoTCAPc) self-assembled monolayer (SAM) immobilized onto a preformed 2-mercaptoethanol (Au-ME) SAM on gold surface (Au-ME-CoTCAPc SAM) as a potential amperometric sensor for the detection of hydrogen peroxide (H₂O₂) at neutral pH conditions. The Au-ME-CoTCAPc SAM sensor showed a very fast amperometric response time of approximately 1 s, good linearity at the studied concentration range of up to 5 μM with a coefficient R² = 0.993 and a detection limit of 0.4 μM oxidatively. Also reductively, the sensor exhibited a very fast amperometric response time (∼1 s), linearity up to 5 μM with a coefficient R² = 0.986 and a detection limit of 0.2 μM. The cobalt tetracarboxylic acid phthalocyanine self-assembled monolayer was then evaluated as a mediator for glucose oxidase (GOx)-based biosensor. The GOx (enzyme) was immobilized covalently onto Au-ME-CoTCAPc SAM using coupling agents: N-ethyl-N(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydroxy succinimide (NHS), and the results demonstrated a good catalytic behavior. Kinetic parameters associated with the enzymatic and mediator reactions were estimated using electrochemical versions of Lineweaver-Burk and Hanes equation, and the stability of the sensor was tested. The biosensor (Au-ME-CoTCAPc-GOx SAM) electrode showed good sensitivity (7.5 nA/mM) with a good detection limit of 8.4 μM at 3σ, smaller Michaelis-Menten constant (4.8 mM from Hanes plot) and very fast response time of approximately 5 s.     

Decreasing resistances of membrane-electrode assemblies containing hydrocarbon-based ionomers for improving their anodic performances

To improve methanol-oxidation performances of membrane-electrode assemblies composed of a hydrocarbon-based ionomers, the resistances involved in the reaction were decreased. Electrochemical impedance spectroscopy revealed that the proton-conductive resistance (R_i) in the anode was decreased from 0.54 to 0.40 Ω cm² by increasing a loading ratio of platinum-ruthenium to carbon support of anode catalyst from 54 to 73 wt.%. In addition, R_i was decreased to be 0.25 Ω cm² by increasing ion-exchange capacity (IEC) of the ionomer from 1.4 to 2.9 mequiv. g⁻¹. Consequently, the polarization resistance of the anode was significantly decreased, in turn, increasing current density of methanol oxidation at the potential of 0.45 V from 0.110 to 0.244 A cm⁻².     

Electrochemical impedance spectroscopy of electrodes modified with thin films of MgMnCO3 layered double hydroxides

The electrochemical impedance spectra of MgMnCO₃ LDH films oxidized at different dc potentials were recorded. The results were fitted to a Randles type cell by replacing the Warburg impedance with a mass transfer resistance in parallel with a constant phase element. The films charge transfer resistances decreased dramatically at the onset of manganese oxidation. In thin films, R_ct decreased from 10⁴ Ω for an un-oxidized film to a minimum of 40 Ω in a film oxidized at 0.32 V, before increasing back to 10⁴ Ω in a film oxidized at 0.5 V. Iodometry measurements show these changes correspond to increases in the manganese average valence in the films from 3.09+ prior to oxidation, to 3.80+ at 0.32 V and 3.95+ at 0.5 V. In thicker films, however, a much higher dc potential, 1.0 V, was required to return R_ct to 10⁴ Ω. There was also less change in the manganese average valence in the thicker films. Oxidation at 1.0 V only increased the manganese valence to 3.33+. For the partially oxidized films, the Nyquist plots consisted of depressed semicircles at high frequency, followed by linear regions at lower frequency where the impedance was controlled by mass transport. The effective diffusion coefficient estimated from the low frequency impedance was 1 × 10⁻⁹ cm² s⁻¹, consistent with proton diffusion in solid electrodes. The impedance spectrum of a partially oxidized film reduced at −0.2 V was similar to that of the un-oxidized film.     

Electrochemical and spectroscopic properties of dendritic cobalto-salicylaldiimine DNA biosensor

A metallodendrimer-based electrochemical DNA biosensor was constructed by a layer-by-layer assembly of cobalt(II) salicylaldiimine metallodendrimer (SDD-Co(II)) and a 21 bases oligonucleotide NH₂-5′-GAGGAGTTGGGGGAGCACATT-3′ (pDNA) on a gold electrode. The complementary oligonucleotide was 5′-AATGTGCTCCCCCAACTCCTC-3′ (tDNA). UV-visible spectra of SDD-Co(II) in 1:1 (v/v) acetone-ethanol solution showed absorption bands at 325 nm and 365-420 nm related to π-π* intra-dendrimer transitions and d-π* metal-dendrimer charge transfer transitions, respectively. Square-wave voltammetry (SWV) characterisation of the Au|SDD-Co(II)|pDNA biosensor system in phosphate buffer saline solution of pH 7.4, indicated a reversible one-electron electrochemical process with a formal potential, E°′, value of +210 mV. Electrochemical impedance spectroscopy (EIS) data confirmed that the hybridisation of the biosensor's pDNA with the tDNA to form double-stranded DNA (dsDNA) resulted in an increase of the impedimetric charge transfer resistance, R_ct, value from 6.52 to 12.85 kΩ. The limit of detection (LOD), calculated as 3σ of the background noise, and sensitivity of the sensor were 1.29 kΩ/nmol L⁻¹ and 0.34 pmol L⁻¹, respectively.     

Mechanistic study of the reduction of copper oxides in alkaline solutions by electrochemical impedance spectroscopy

Electrochemical impedance spectroscopy was used to study the mechanism by which copper oxides are reduced in alkaline solutions. For the reductions of CuO and Cu₂O, a capacitive loop and also an inductive loop under certain conditions were observed in the complex plane. The electrochemical impedance for CuO reduction was not greatly dependent on the solution alkalinity and the kind of alkali hydroxide. However, the electrochemical impedance for Cu₂O reduction was considerably affected by the kind and concentration of alkali hydroxide. The diameter of the capacitive loop, i.e., the charge-transfer resistance (R_ct), was increased with increase in solution alkalinity. It should also be noted that R_ct was increased in the order of KOH < NaOH < LiOH. These dependences were consistent with the good separation between the reduction potentials of CuO and Cu₂O in chronopotentiometric and voltammetric measurements with strongly alkaline electrolytes containing Li⁺. The inductive loop observed for the Cu₂O reduction at higher concentrations of KOH (>6 M) and LiOH (>0.2 M) suggested the existence of an intermediate species (probably CuOH). The specific inhibitory effect of Li⁺ ions on the reduction of Cu₂O might be explained by a possible stabilization of CuOH by Li⁺ ions.     

Electrochemical characteristics of LSCF-SDC composite cathode for intermediate temperature SOFC

A kind of composite cathode, La_0.58Sr_0.4Co_0.2Fe_0.8O_3−δ-Ce_0.8Sm_0.2O_2−δ (LSCF-SDC), was presented in this paper. The electrochemical performance of the cathode on the electrolyte of SDC and YSZ coated with a thin SDC (YSZ/SDC) layer was studied by electrochemical impedance spectroscopy (EIS) and cathodic polarization techniques for their potential utilization in the intermediate temperature solid oxide fuel cell (IT-SOFC). Also studied was the relationship between the electro-catalytic characteristics and the electrode microstructure. Results showed that the LSCF-SDC composite electrode performed better on the SDC electrolyte than on the electrolyte of YSZ/SDC. The polarization resistance, R_p, of the cathode on the SDC electrolyte was 0.23 Ω cm² at 700 °C and 0.067 Ω cm² at 750 °C, much lower than the corresponding R_p of the same cathode on the YSZ/SDC electrolyte. At 750 °C, the cathodic overpotential of the composite cathode on the SDC electrolyte was 99.7 mV at the current density of 1.0 A cm⁻².     

Monitoring the real time growth of a self-assembled monolayer on a polymer electrolyte surface

The growth of a self-assembled monolayer (SAM) at the surface of a polymer electrolyte has been shown to inhibit the formation of the passivating layer that forms when the polymer is in contact with lithium metal. In this work, ac impedance spectroscopy was used to monitor the formation of SAM layers on polyethylene oxide (PEO) polymer electrolyte thin films as a function of time. To monitor SAM growth, thin PEO films were cast onto interdigitated electrodes. The electrodes were subsequently immersed in a saturated SAM solution and the film impedance was measured. SAM molecules with the general formula: H(CH₂)₃₂(CH₂CH₂O)_yH (y = 2, 10, 40) were used. Growth occurred due to interactions with the ethylene oxide portion of the SAM molecules with the PEO surface. To visualize SAM growth impedance data at a single frequency sensitive to changes at the solution interface was plotted verses time. At the point of immersion, a sharp increase in impedance was observed. With time, the rate at which the impedance increased slowed and ultimately leveled off presumably indicating the point at which a nearly complete monolayer had formed. SAM growth was verified using attenuated total reflectance infrared spectroscopy (ATR-IR).     

The effect of Al(OH)3 coating on the Li[Li0.2Ni0.2Mn0.6]O2 cathode material for lithium secondary battery

Layered Li[Li_0.2Ni_0.2Mn_0.6]O₂ powder was modified by coating its surface with amorphous Al(OH)₃. Energy dispersive spectroscopy (EDS) showed that nano-sized Al(OH)₃ powders were homogeneously dispersed in the parent Li[Li_0.2Ni_0.2Mn_0.6]O₂ powders. Al(OH)₃ coated Li[Li_0.2Ni_0.2Mn_0.6]O₂ exhibited an greater retention capacity at higher rates compared to uncoated Li[Li_0.2Ni_0.2Mn_0.6]O₂. The low area specific impedance (ASI) value of the Al(OH)₃ is the major factor for its higher rate performance. The 1.4 wt.% Al(OH)₃ coated sample had an impedance of 41 Ω cm² while uncoated Li[Li_0.2Ni_0.2Mn_0.6]O₂ had a 57 Ω cm² at 30-80% state of charge. Electrochemical impedance spectroscopy (EIS) also showed that the Al(OH)₃ coated sample had a lower charge transfer resistance (R_ct) than the uncoated sample. Differential scanning calorimetry (DSC) analysis showed that Al(OH)₃ coating improved the thermal stability. Al(OH)₃ coating increased the onset temperature of thermal decomposition and reduced the amount of heat for the exothermic peak.     

Surface modification of passive iron by alkyl-phosphonic acid layers

Phosphonate layer formation on passive iron surface has been investigated by electrochemical, conversion electron Mössbauer spectroscopy (CEMS) and atomic force microscopy (AFM) techniques. Electrochemical methods revealed that the prepassivation of iron surface results in stabilization of the phosphonate layer exhibiting favorable corrosion resistance. The rate of anodic dissolution is continuously decreasing due to the time-dependent formation of a protective phosphonate layer.The large R_ct values of 1-20 MΩ cm² indicate rather high blocking effect of metal dissolution by the phosphonate layer. The phosphonate layer formation has been also followed by the decrease of capacitance. CEMS investigations were carried out to evaluate the differences in the composition of the passive layer as a result of the phosphonate treatment. Mössbauer spectroscopy indicated the presence of iron phosphonate. Changes in morphology due to the phosphonate layer formation have been observed.     

Polyaniline for corrosion prevention of mild steel coupled with copper

Polyaniline emeraldine base/epoxy resin (EB/ER) coating was investigated for corrosion protection of mild steel coupled with copper in 3.5% NaCl solution. EB/ER coating with 5-10 wt% EB had long-term corrosion resistance on both uncoupled steel and copper due to the passivation effect of EB on the metal surfaces. During the 150 immersion days, the impedance at 0.1 Hz for the coating increased in the first 1-40 days and subsequently remained constant above 10⁹ Ω cm², whereas that for pure ER coating fell below 10⁶ Ω cm² after only 30 or 40 days. Immersion tests on coated steel-copper galvanic couple showed that EB/ER coating offered 100 times more protection than ER coating against steel dissolution and coating delamination on copper, which was mainly attributed to the passive metal oxide films formed by EB blocking both the anodic and cathodic reactions. Salt spray tests showed that 100 μm EB/ER coating protected steel-copper couple for at least 2000 h.     

An electrochemical DNA biosensor developed on novel multinuclear nickel(II) salicylaldimine metallodendrimer platform

An electrochemical DNA biosensor (EDB) was prepared using an oligonucleotide of 21 bases with sequence NH₂-5′-GAGGAGTTGGGGGAGCACATT-3′ (probe DNA) immobilized on a novel multinuclear nickel(II) salicylaldimine metallodendrimer on glassy carbon electrode (GCE). The metallodendrimer was synthesized from amino functionalized polypropylene imine dendrimer, DAB-(NH₂)₈. The EDB was prepared by depositing probe DNA on a dendrimer-modified GCE surface and left to immobilize for 1 h. Voltammetric and electrochemical impedance spectroscopic (EIS) studies were carried out to characterize the novel metallodendrimer, the EDB and its hybridization response in PBS using [Fe(CN)₆]^3−/4− as a redox probe at pH 7.2. The metallodendrimer was electroactive in PBS with two reversible redox couples at E°′ = +200 mV and E°′ = +434 mV; catalytic by reducing the E_pa of [Fe(CN)₆]^3−/4− by 22 mV; conducting and has diffusion coefficient of 8.597 × 10⁻⁸ cm² s⁻¹. From the EIS circuit fitting results, the EDB responded to 5 nM target DNA by exhibiting a decrease in charge transfer resistance (R_ct) in PBS and increase in R_ct in [Fe(CN)₆]^3−/4− redox probe; while in voltammetry, increase in peak anodic current was observed in PBS after hybridization, thus giving the EDB a dual probe advantage.     

Modification of copper with self-assembled organic coatings

Self-assembled monolayers of n-alkanethiols (CH₃(CH₂)_n−1SH; n = 12 and 18) were prepared on a copper surface, and the quality and protection efficiency of resulting coatings against aqueous corrosion of copper were investigated. A combination of physical (scanning electron microscopy, energy dispersive X-ray spectroscopy and contact angle measurements) and electrochemical (cyclic voltammetry and impedance spectrometry) methods was used to correlate the structure of the coatings with their barrier properties during exposures in an aqueous solution. Impedance results reveal that the coatings behave almost like an ideal dielectric, with a resistance of several MΩ cm² and a coating capacitance that agree well with the value calculated according to the theory of dielectrics. Protection efficiency of chemisorbed alkanethiol coatings determined from dc and ac measurements were above 99%.     

Influence of iodine concentration on the photoelectrochemical performance of dye-sensitized solar cells containing non-volatile electrolyte

The effect of iodine concentration in the electrolyte with non-volatile solvent of dye-sensitized solar cells (DSCs) on photovoltaic performance was studied. The electron transport and interfacial recombination kinetics were also systematically investigated by electron impedance spectroscopy (EIS). With the iodine concentration increased from 0.025 to 0.1 M, open-circuit voltage (V_oc) and photocurrent density (J_sc) decreased while fill factor (ff) increased significantly. The decline of the V_oc and J_sc was mainly ascribed to increased electron recombination with tri-iodide ions (I₃⁻). The increased fill factor was primarily brought by a decrease in the total resistance. From impedance spectra of the solar cells, it can be concluded that increasing the iodine concentration in electrolytes could decrease charge transfer resistance (R_ct) and the chemical capacitance (C_μ), increase the electron transport resistance (R_t), and hence decrease the electron lifetime (τ) and the effective diffusion coefficient (D_n) of electrons in the TiO₂ semiconductor. With optimum iodine concentration, device showed a photocurrent density of 16.19 mA cm⁻², an open-circuit voltage of 0.765 V, a fill factor of 0.66, and an overall photo-energy conversion efficiency of 8.15% at standard AM 1.5 simulated sunlight (100 mW cm⁻²).     

Self-assembled monolayers of a disulphide-derivatised cobalt-porphyrin on gold

A self-assembled monolayer (SAM) of a novel cobalt(II)porphyrin disulphide derivative was prepared on flat gold(1 1 1) electrode. Evidence for surface modification was provided by electrochemical reductive desorption of the monolayer and ellipsometry, consistent with a coverage of 2.5 × 10⁻¹⁰ mol cm⁻² and a thickness of 13 Å, respectively. Both results support the presence of SAMs where the molecules share an intermediate position between perpendicular and flat orientation. Scanning tunnelling microscopy have also proven the formation of CoPSS SAMs, however high-resolution images could only be obtained when the CoPSS molecules were diluted in an hexanethiol SAM. The electrocatalytic activity of the surface confined Co-porphyrin was evaluated for the oxygen reduction. Voltammetric data indicate that reaction involves two electrons consistent with the formation of hydrogen peroxide. Under similar experimental conditions the data obtained for an iron-porphyrin analogue points for a full reduction of dioxygen to water.     

Self-assembled monolayers-based immunosensor for detection of Escherichia coli using electrochemical impedance spectroscopy

An electrochemical impedance immunosensor for the detection of Escherichia coli was developed by immobilizing anti-E. coli antibodies at an Au electrode. The immobilization of antibodies at the Au electrode was carried out through a stable acyl amino ester intermediate generated by 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydrosuccinimide (NHS), which could condense antibodies reproducibly and densely on the self-assembled monolayer (SAM). The surface characteristics of the immunosensor before and after the binding reaction of antibodies with E. coli were characterized by atomic force microscopy (AFM). The immobilization of antibodies and the binding of E. coli cells to the electrode could increase the electro-transfer resistance, which was directly detected by electrochemical impedance spectroscopy (EIS) in the presence of Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ as a redox probe. A linear relationship between the electron-transfer resistance and the logarithmic value of E. coli concentration was found in the range of E. coli cells from 3.0 × 10³ to 3.0 × 10⁷ cfu mL⁻¹ with the detection limit of 1.0 × 10³ cfu mL⁻¹. With preconcentration and pre-enrichment steps, it was possible to detect E. coli concentration as low as 50 cfu/mL in river water samples.     

A new corrosion protection coating with polyaniline-TiO2 composite for steel

Organic coating strategies for corrosion protection with inherently conducting polymers have become important because of restriction on the use of heavy metals and chromates in coatings due to their environmental problems. This work presents the synthesis of polyaniline-TiO₂ composites (PTC) and the corrosion protection behaviour of PTC containing coating on steel. PTC was prepared by chemical oxidation of aniline and TiO₂ by ammonium persulfate in phosphoric acid medium. The PTC was characterized by FTIR, XRD and SEM techniques. Suitable coating with PTC was formed on steel using acrylic resin. Using electrochemical impedance spectroscopy, the PTC containing coating's behaviour in 3% NaCl immersion test and salt spray test has been found out. Results indicate that the coating containing PTC is able to maintain the potential of steel in passive region due to its redox property. The resistance of the coating containing PTC was more than 10⁷ Ω cm² in 3% NaCl solution after 60 days and 10⁹ Ω cm² in the salt spray test of 35 days. But the resistance of the TiO₂ containing coating was found to be less than 10⁴ Ω cm² in both the cases. The high performance of PTC containing coating is attributed to the passivation of steel by polyaniline.     

Electrocatalytic activities of gold-5-amino-2-mercaptobenzimidazole-M self-assembled monolayer complexes (M: Ag, Cu) for hydroquinone oxidation investigated by CV and EIS

Electrocatalytic activity of a new catalyst toward the oxidation reaction of hydroquinone as a model compound is described. The catalyst was formed by immobilizing metal cations on the topside of a gold-5-amino-2-mercaptobenzimidazole, self-assembled monolayer (Au-5A2MBI-Mⁿ⁺ SAM, Mⁿ⁺: Cu²⁺, Ag⁺) electrode. Preparation steps and the electrocatalytic activity of the catalyst were studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The EIS data were approximated by appropriate electronic equivalent circuit models from which kinetic parameters, such as charge transfer resistance, double layer capacitance, and apparent rate constant (k_app), were estimated. Excellent activity was observed for Au-5A2MBI-Ag⁺ SAM with the following order: Au-5A2MBI-Ag⁺ > Au-5A2MBI-Cu²⁺ > Au-5A2MBI, after testing many modified electrodes. The increased activity originates from a modification of the Au-5A2MBI structure by mediating the effect of Ag⁺. This behavior was understood from significant increases in the k_app without significant changes in the double layer capacitance.     

Self-assembled monolayers (SAMs) of cobalt tetracarboxylic acidchloride phthalocyanine covalently attached onto a preformed mercaptoethanol SAM: A novel method

A feasible method of fabricating phthalocyanine sensor was developed by covalent attachment of cobalt tetracarboxylic acidchloride phthalocyanine (CoTCACIPc) onto a preformed 2-mercaptoethanol (2-ME) self-assembled monolayer (SAM) modified gold electrode (designated as CoTCACIPc-2-ME-SAM). The surface concentration of the CoTCACIPc was found to be 4.58 × 10⁻¹⁰ mol/cm². The sensor gave a linear response to l-cysteine over the concentration range 0.28-20 μM with a detection limit of 5 × 10⁻⁷ M and best response time of 2 s.     

PrBa0.5Sr0.5Co2O5+δ layered perovskite cathode for intermediate temperature solid oxide fuel cells

Layered perovskite oxides have ordered A-cations localizing oxygen vacancies, and may potentially improve oxygen ion diffusivity and surface exchange coefficient. The A-site-ordered layered perovskite PrBa_0.5Sr_0.5Co₂O_5+δ (PBSC) was evaluated as new cathode material for intermediate temperature solid oxide fuel cells (IT-SOFCs). The material was characterized using electrochemical impedance spectroscopy in a symmetrical cell system (PBSC/Ce_0.9Sm_0.1O_1.9 (SDC)/PBSC), exhibiting excellent performance in the intermediate temperature range of 500-700 °C. An area-specific-resistance (ASR) of 0.23 Ω cm² was achieved at 650 °C for cathode polarization. The low activation energy (Ea) 124 kJ mol⁻¹ is comparable to that of La_0.8Sr_0.2CoO_3−δ. A laboratory-scaled SDC-based tri-layer cell of Ni-SDC/SDC/PBSC was tested in intermediate temperature conditions of 550 to 700 °C. A maximum power density of 1045 mW cm⁻² was achieved at 700 °C. The interfacial polarization resistance is as low as 0.285, 0.145, 0.09 and 0.05 Ω cm² at 550, 600, 650 and 700 °C, respectively. Layered perovskite PBSC shows promising performance as cathode material for IT-SOFCs.