Synthesis of highly crystalline spinel LiMn2O4 by a soft chemical route and its electrochemical performance

Highly crystalline spinel LiMn₂O₄ was successfully synthesized by annealing lithiated MnO₂ at a relative low temperature of 600 °C, in which the lithiated MnO₂ was prepared by chemical lithiation of the electrolytic manganese dioxide (EMD) and LiI. The LiI/MnO₂ ratio and the annealing temperature were optimized to obtain the pure phase LiMn₂O₄. With the LiI/MnO₂ molar ratio of 0.75, and annealing temperature of 600 °C, the resulting compounds showed a high initial discharge capacity of 127 mAh g⁻¹ at a current rate of 40 mAh g⁻¹. Moreover, it exhibited excellent cycling and high rate capability, maintaining 90% of its initial capacity after 100 charge-discharge cycles, at a discharge rate of 5 C, it kept more than 85% of the reversible capacity compared with that of 0.1 C.     

Rechargeable Li/LiFePO4 cells using N-methyl-N-butyl pyrrolidinium bis(trifluoromethane sulfonyl)imide-LiTFSI electrolyte incorporating polymer additives

We have incorporated polymer additives such as poly(ethylene glycol) dimethyl ether (PEGDME) and tetra(ethylene glycol) dimethyl ether (TEGDME) into N-methyl-N-butylpyrrolidinium bis(trifluoromethane sulfonyl)imide (PYR₁₄TFSI)-LiTFSI mixtures. The resulting PYR₁₄TFSI + LiTFSI + polymer additive ternary electrolyte exhibited relatively high ionic conductivity as well as remarkably low viscosity over a wide temperature range compared to the PYR₁₄TFSI + LiTFSI binary electrolytes. The charge/discharge cyclability of Li/LiFePO₄ cells containing the ternary electrolytes was investigated. We found that Li/PYR₁₄TFSI + LiTFSI + PEGDME (or TEGDME)/LiFePO₄ cells containing the two different polymer additives showed very similar discharge capacity behavior, with very stable cyclability at room temperature (RT). Li/PYR₁₄TFSI + LiTFSI + TEGDME/LiFePO₄ cells can deliver about 127 mAh/g of LiFePO₄ (74.7% of theoretical capacity) at 0.054 mA/cm² (0.2C rate) at RT and about 108 mAh/g of LiFePO₄ (63.4% of theoretical capacity) at 0.023 mA/cm² (0.1C rate) at −1 °C for the first discharge. The cell exhibited a capacity fading rate of approximately 0.09-0.15% per cycle over 50 cycles at RT. Consequently, the PYR₁₄TFSI + LiTFSI + polymer additive ternary mixture is a promising electrolyte for cells using lithium metal electrodes such as the Li/LiFePO₄ cell reported here. These cells showed the capability of operating over a significant temperature range (∼0-∼30 °C).     

High power supercapacitors using polyacrylonitrile-based carbon nanofiber paper

Porous carbon nanofiber paper has been obtained by one-step carbonization/activation of PAN-based nanofiber paper at temperatures from 700 to 1000 °C in CO₂ atmosphere. The paper was used as supercapacitor electrode without any binder or percolator. At low temperature, e.g., ?900 °C, nitrogen enriched carbons with a poorly developed specific surface area (S_BET ? 400 m²/g) are obtained. In aqueous electrolytes, these carbons withstand high current loads without a noticeable decrease of capacitance, and the normalized capacitance reaches 67 μF/cm². At 10 s time constant, the values of energy and power densities are 3-4 times higher than for activated carbons (AC) presenting higher specific surface area. By carbonization/activation at 1000 °C, subnanometer pores are developed and S_BET = 705 m²/g. Despite moderate BET specific surface area, the capacitance reaches values higher than 100 F/g in organic electrolyte. At high power densities, the nanofiber paper obtained at 1000 °C outperforms the energy density retention of ACs in organic electrolyte. The high power capability of the carbon nanofiber papers in the two kinds of electrolytes is attributed both to the high intrinsic conductivity of the fibers and to the high diffusion rate of ions in the opened mesopores.     

Assessment of structurally stable cubic Bi12TiO20 as intermediate temperature solid oxide fuels electrolyte

Colloid processing and subsequent pressure filtration were used to prepare 14.3 mol% TiO₂ doped Bi₂O₃ (Bi₁₂TiO₂₀, 14BTO) as solid oxide fuel cell electrolyte. Materials characterization and electrical behaviors of 14BTO samples were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and two-point probe DC conductivity. A pure 14BTO with a cubic sillenite single phase was prepared at the sintering process of 850 °C with a high relative sintered density of 96.82%. In situ and batch-type long-term conductivity measurements at 600 °C were carried out to verify the possible reason of degradation. Additional reduction-oxidation tests under CH₄ atmosphere by thermogravimetric analysis (TGA) revealed possible application temperature of 14BTO electrolytes below 700 °C.     

Optimization of EC-based multi-solvent electrolytes for low temperature applications of lithium-ion batteries

The ionic conductivities of EC-based multi-component electrolytes in various solvent compositions were measured over a wide temperature range of +40 to −40 °C, and the factors affecting the low temperature conductivities of the electrolytes were discussed. It is revealed from the experimental results that the co-solvents with high dielectric constant and low viscosity can improve the ionic conductivity at room temperature, whereas, only the co-solvents which possess low melting points can effectively expand the operating temperature range of the electrolyte. The Li-ion batteries using the optimized electrolyte of 1 M LiPF₆/EC-DMC-EMC (8.3:25:66.7) show the capacity retentions about 90.3% of their nominal capacities when discharged to 2.0 V at −40 °C at 0.1 C, demonstrating excellent low temperature performances.     

Preparation and characterization of 10 mol% Gd doped CeO2 (GDC) electrolyte for SOFC applications

Ceria-based materials are prospective electrolytes for low and intermediate temperature solid oxide fuel cells. In the present work, fully dense CeO₂ ceramics doped with 10 mol% gadolinium (Gd_0.1Ce_0.9O_1.95, GDC) have been prepared with a Pechini method. Characterization studies were realized with thermo-gravimetric analysis (TGA), differential thermal analysis (DTA), mass spectroscopy (MS), high temperature FT-IR (HT-FTIR) and X-ray diffraction analysis (XRD). A single-phase with a fluorite type structure was found to form at a relatively low calcination temperature of 500 °C. Dense GDC pellets having 98% of the relative density were obtained at sintering temperature of 1400 °C/6 h, which gave significantly higher total ionic conductivity of 3.4×10⁻² S cm⁻¹ at 500 °C in air. The present work showed that the Pechini method is a relatively low-temperature preparation technique to synthesize Gd_0.1Ce_0.9O_1.95 powders that provided high sinterability and good ionic conductivity.     

The role of gel electrolyte composition in the kinetics and performance of dye-sensitized solar cells

Gel-type polymer electrolytes based on the copolymer poly(ethylene oxide-co-epichlorohydrin) and the plasticizer γ-butyrolactone (GBL) were optimized and applied in dye-sensitized solar cells. The plasticizer added to the electrolyte allowed the dissolution of a higher concentration of salt, reaching conductivity values close to 1 mS cm⁻¹ for the sample prepared with 30 wt% of LiI. Raman spectroscopy confirmed polyiodide formation in the electrolyte when the salt concentration exceeds 7.5 wt%, introducing a significant contribution of electronic conductivity in the electrolyte. The devices were characterized under AM 1.5 conditions and the I-V curves were fitted using a two diode equation. Increasing the concentration of LiI-I₂ accelerates dye cation regeneration as measured by transient absorption spectroscopy; however, it also contributes to an increase in the dark current of the cell by one order of magnitude. The best performance was achieved for the solar cell prepared with the electrolyte containing 20 wt% of LiI, with efficiencies of 3.26% and 3.49% at 100 and 10 mW cm⁻² of irradiation, respectively.     

Dye sensitized solar cells with poly(acrylonitrile) based plasticized electrolyte containing MgI2

Polymer electrolytes can be used favorably in photo-electrochemical solar cells. A possible electrolyte for this purpose is a polyacrylonitrile-MgI₂ complex with plasticizers such as ethylene carbonate and propylene carbonate. The best ionic conductivity was obtained for samples containing 60 wt% of MgI₂ salt with respect to the weight of polyacrylonitrile, for example, at 30 °C the conductivity is 1.9 × 10⁻³ S cm⁻¹. The ionic contribution to the conductivity is dominant as shown by dc polarization tests. Furthermore, the glass transition temperature showed a minimum, −103.0 °C, for the sample with the highest conductivity indicating the importance of polymer chain flexibility for the conduction process. Measurements on a fabricated solar cell with this electrolyte exhibited an overall energy conversion efficiency of 0.84%. The short circuit current density, open circuit voltage and fill factor of the cell were 2.04 mA cm⁻², 692 mV and 59.3%, respectively.     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

Solvents in salt electrolyte: Benefits and possible use as electrolyte for lithium-ion battery

An EC/DEC [40:60% (v/v)] solvent mixture has been added in various amounts to the ionic liquid (IL) hexyltrimethylammonium bis(trifluoromethylsulfonyl)imide (N₁₁₁₆-NTf₂) in the presence of LiNTf₂ (lithium bis(trifluoromethylsulfonyl)imide) as lithium salt for possible use as electrolytes in lithium-ion batteries. These electrolytes exhibit a larger thermal stability than the reference electrolyte EC/DEC [40:60] + LiNTf₂ 1 M when the percentage of the IL exceeds 30% (v/v). All studied electrolytes are glass forming ones with an ideal glass transition temperature of ca. −85 °C(±5 °C), which has been determined by application of the VTF theory to conductivity and viscosity measurements and confirmed by DSC (T_g = −90 ± 5 °C). An electrochemical window of about 5 V versus Li/Li⁺ was measured at a glassy carbon electrode. The cycling ability of the optimized electrolyte N₁₁₁₆-NTf₂/EC:DEC (40/60% (v/v)) + 1 M LiNTf₂ has been investigated at a titanate oxide (Li₄Ti₅O₁₂) and a cobalt oxide (Li_xCoO₂) electrodes. Cycling the positive and the negative electrodes was conducted successfully with a high capacity and without any significant fading.     

Electrochemical production of Ti-Al alloys using TiCl4-AlCl3-1-butyl-3-methyl imidazolium chloride (BmimCl) electrolytes

Electrochemical production of Ti-Al alloys was investigated using TiCl₄-AlCl₃-1-butyl-3-methyl imidazolium chloride (BmimCl) electrolytes (molar ratio 0.019:2:1). The experiments were conducted at different temperatures between 70 and 125 ± 3 °C and at various cell voltages between 1.5 and 3.0 V. Morphology and composition of deposited Ti-Al alloys were characterized using scanning electron microscope (SEM), along with energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The Ti-Al alloys containing about 15-27 at% Ti were produced with a current efficiency of about 25-38%. TiCl₃ passivation on electrodes hinders the deposition kinetics and hence very low cathodic current density and cathodic current efficiency was obtained. This study also focused to determine the effect of process variables such as applied voltage, electrolyte composition and temperature on cathode current density, current efficiency, composition and morphology of Ti-Al alloys. The optimized condition for producing finer particle size and high Ti content in Ti-Al alloys was obtained between the applied voltages of 1.5-2.0 V and temperature ranges from 70 to 100 °C.     

Novel chemically cross-linked solid state electrolyte for dye-sensitized solar cells

Poly(vinylpyridine-co-ethylene glycol methyl ether methacrylate) (P(VP-co-MEOMA)) and α,ω-diiodo poly(ethylene oxide-co-propylene oxide) (I[(EO)_0.8-co-(PO)_0.2]_yI) were synthesized and used as chemically cross-linked precursors of the electrolyte for dye-sensitized solar cells. Meanwhile, α-iodo poly(ethylene oxide-co-propylene oxide) methyl ether (CH₃O[(EO)_0.8-co-(PO)_0.2]_xI) was synthesized and added into the electrolyte as an internal plasticizer. Novel polymer electrolyte resulting from chemically cross-linked precursors was obtained by the quaterisation at 90 °C for 30 min. The characteristics for this kind of electrolyte were investigated by means of ionic conductivity, thermogravimetric and photocurrent-voltage. The ambient ionic conductivity was significantly enhanced to 2.3 × 10⁻⁴ S cm⁻¹ after introducing plasticizer, modified-ionic liquid. The weight loss of the solid state electrolyte at 200 °C was 1.8%, and its decomposition temperature was 287 °C. Solid state dye-sensitized solar cell based on chemically cross-linked electrolyte presented an overall conversion efficiency of 2.35% under AM1.5 irradiation (100 mW cm⁻²). The as-fabricated device maintained 88% of its initial performance at room temperature even without sealing for 30 days, showing a good stability.     

Fabrication and characterization of composite electrolyte for intermediate-temperature SOFC

In this study, a ceria-based composite electrolyte was investigated for intermediate-temperature solid oxide fuel cells (SOFCs) based on SDC-25 wt.% K₂CO₃. Sodium carbonate co-precipitation process by which SDC powder was adopted and sound cubic fluorite structure was formed after SDC powders were sintered at 750 °C for 3 h. The crystallite size of the particle was 21 nm in diameter as calculated from data obtained through X-ray diffraction. The conductivity of the composite electrolyte proposed in this study was much higher than that of pure SDC at the comparable temperature of 550-700 °C. The transition of the ionic conductivity occurred at 650 °C. Based on this type of composite electrolyte, single cell with the electrolyte thickness of 0.3 mm were fabricated using dry pressing, with nickel oxide adopted as anode and SSC as cathode. The single cell was then tested at 550-700 °C on home-made equipment in this study, using hydrogen/air. The maximum power density and open circuit voltage (OCV) achieved 600 mW cm⁻² and 1.05 V at 700 °C, respectively.     

Microstructure and dielectric properties of Dy/Mn doped BaTiO3 ceramics

Dy/Mn doped BaTiO₃ with different Dy₂O₃ contents, ranging from 0.1 to 5.0 at% Dy, were investigated regarding their microstructural and dielectric characteristics. The content of 0.05 at% Mn was constant in all the investigated samples. The samples were prepared by the conventional solid state reaction and sintered at 1290°, and 1350 °C in air atmosphere for 2 h. The low doped samples (0.1 and 0.5 at% Dy) exhibit mainly fairly uniform and homogeneous microstructure with average grain sizes ranged from 0.3 μm to 3.0 μm. At 1350 °C, the appearance of secondary, abnormal, grains in the fine grain matrix and core–shell structure were observed in highly doped Dy/BaTiO₃. Dielectric measurements were carried out as a function of temperature up to 180 °C. The low doped samples sintered at 1350 °C, display the high value of dielectric permittivity at room temperature, 5600 for 0.1Dy/BaTiO₃. A nearly flat permittivity–temperature response was obtained in specimens with 2.0 and 5.0 at% additive content. Using a Curie–Weiss and modified Curie–Weiss low, the Curie constant (C), Curie like constant (C′), Curie temperature (T_C) and a critical exponent (γ) were calculated. The obtained values of γ pointed out the diffuse phase transformation in highly doped BaTiO₃ samples.     

Heteropolyacid in glass electrolytes for the development of H2/O2 fuel cells

The scope of the present work was to investigate and evaluate the electrochemical activity of H₂/O₂ fuel cells based on the influence of a heteropolyacid glass membrane with a Pt/C electrode at low temperature. A new trend of sol-gel derived PMA (H₃PMo₁₂O₄₀) heteropolyacid-containing glass membranes inherent of a high proton conductivity and mechanical stability, was heat treated at 600 °C and implemented to H₂/O₂ fuel cell activities through electrochemical characterization. Significant research has been focused on the development of H₂/O₂ fuel cells using optimization of heteropolyacid glasses as electrolytes with Pt/C electrodes at 30 °C. A maximum power density of 23.9 mW/cm² was attained for operation with hydrogen and oxygen, respectively, at 30 °C and 30% humidity with the PMA glass membranes (4-92-4 mol%). Impedance spectroscopy measurements were performed on a total ohmic cell resistance of a membrane-electrode-assembly (MEA) at the end of the experiment.     

Effect of fluoroethylene carbonate on high temperature capacity retention of LiMn2O4/graphite Li-ion cells

In order to overcome severe capacity fading of LiMn₂O₄/graphite Li-ion cells at high temperature at 60 °C, fluoroethylene carbonate (FEC) was newly evaluated as an electrolyte additive. With 2 wt.% FEC addition into the electrolyte (EC/DEC/PC with 1 M LiPF₆), the capacity retention at 60 °C after 130 cycles was significantly improved by about 20%. To understand the underlying principle on the capacity retention enhancement, the electrochemical properties of the cells including cell performance, impedance behavior as well as the characteristics of the interfacial properties were examined. Based on these results, it is suggested that the improved capacity retention of LiMn₂O₄/graphite Li-ion cells with addition of FEC especially at high temperature is mainly originated from the thin and stable SEI layer formed on the graphite anode surface.     

Cation driven actuation for free standing PEDOT films prepared from propylene carbonate electrolytes containing TBACF3SO3

Free standing PEDOT [poly(3,4-ethylenedioxythiophene)] films (with surface conductivities of 200-400 S cm⁻¹) were generated in tetrabutylammonium trifluromethanesulfonate (TBACF₃SO₃) electrolytes by potentiostatic (E_P 1.05 V vs. Ag wire) electropolymerisation in propylene carbonate (at −27 °C) and methyl benzoate (at −4 °C). Films obtained in the TBACF₃SO₃ electrolytes showed a length increase of 2-3% during scans to negative potentials under isotonic (constant load 1.35 MPa) and stress of 0.3 MPa under isometric (constant length) conditions. Cation movement occurred due to immobilisation of CF₃SO₃⁻ anions during electropolymerisation. The system showed good stability and low creep during square wave electrochemical cycling in the potential range from 0.0 to 1.0 V. The surface morphology (SEM) of the PEDOT films showed that the polymer structure is dependent upon the solvent used during the polymerisation process.     

Soft matter electrolytes based on polymethylmetacrylate dispersions in lithium bis(trifluoromethanesulfonyl)imide/1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids

Ion transport in a polymer-ionic liquid (IL) soft matter composite electrolyte is discussed here in detail in the context of polymer-ionic liquid interaction and glass transition temperature. The dispersion of polymethylmetacrylate (PMMA) in 1-butyl-3-methylimidazolium hexafluorophosphate (BMIPF₆) and 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMITFSI) resulted in transparent composite electrolytes with a “jelly-like” consistency. The composite ionic conductivity measured over the range −30 °C to 60 °C was always lower than that of the neat BMITFSI/BMIPF₆ and LiTFSI-BMITFSI/LiTFSI-BMIPF₆ electrolytes but still very high (>1 mS/cm at 25 °C up to 50 wt% PMMA). While addition of LiTFSI to IL does not influence the glass T_g and T_m melting temperature significantly, dispersion of PMMA (especially at higher contents) resulted in increase in T_g and disappearance of T_m. In general, the profile of temperature-dependent ionic conductivity could be fitted to Vogel-Tamman-Fulcher (VTF) suggesting a solvent assisted ion transport. However, for higher PMMA concentration sharp demarcation of temperature regimes between thermally activated and solvent assisted ion transport were observed with the glass transition temperature acting as the reference point for transformation from one form of transport mechanism to the other. Because of the beneficial physico-chemical properties and interesting ion transport mechanism, we envisage the present soft matter electrolytes to be promising for application in electrochromic devices.     

Sintering,microstructure and conductivity of La2NiO4+δ ceramic

Microstructure and electrical conducting properties of La₂NiO_4+δ ceramic were investigated in the sintering temperature range 1200–1400 °C. The results demonstrate that the microstructure and electrical conducting properties of La₂NiO_4+δ ceramic are sensitive to sintering temperature. Compared with a progressive densification development with sintering temperature from 1200 to 1300 °C along with an insignificant change in grain size, there is an exaggerated grain growth in the specimens sintered at higher temperatures. Increasing sintering temperature from 1200 to 1300 °C resulted in an enhancement of electrical conducting properties. Further increase of sintering temperature exceeding 1300 °C reduced the electrical conducting properties. A close relation between the microstructure and electrical conducting properties was suggested for La₂NiO_4+δ ceramic. With respect to the electrical conducting properties, the preferred sintering temperature of La₂NiO_4+δ ceramic was ascertained to be 1300 °C. The specimen sintered at 1300 °C exhibits a generally uniform microstructure together with electrical conductivities of 76–95 S cm⁻¹ at 600–800 °C.     

Decomposition of MgSiN2 in nitrogen atmosphere

Magnesium silicon nitride MgSiN₂ was prepared by direct nitridation of Si/Mg₂Si/Mg/Si₃N₄ powder compact in a temperature range 1350-1420 °C. The thermal stability examination showed that MgSiN₂ is stable up to 1400 °C at 0.1 MPa N₂ pressure. The activation energy of decomposition of MgSiN₂ calculated from the temperature dependence of mass loss in the range of 1400-1650 °C is ΔH = 501 kJ mol⁻¹. The time dependence and nitrogen pressure dependence of MgSiN₂ decomposition was also investigated at constant temperature. MgSiN₂ is stable at 1560 °C in 0.6 MPa nitrogen atmosphere. Using these experimental data together with the heat capacity published in a literature the Gibbs energy of formation of MgSiN₂ was calculated in a temperature range 25-2200 °C.