Li-ion diffusion kinetics in LiMn2O4 thin films prepared by pulsed laser deposition

LiMn₂O₄ thin films were deposited on Au substrates by pulsed laser deposition (PLD). The Li-ion chemical diffusion coefficients of the films, , were measured by cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT), potentiostatic intermittent titration technique (PITT), and electrochemical impedance spectroscopy (EIS). It was found that the values by CV and PITT were in the order of 10⁻¹³ cm² s⁻¹, and those by EIS and GITT were in the range of 10⁻¹³ to 10⁻¹¹ and 10⁻¹⁴ to 10⁻¹¹ cm² s⁻¹, respectively. These data were compared with the previously reported values.     

Kinetic analysis on LiFePO4 thin films by CV, GITT, and EIS

LiFePO₄ thin films were deposited on Ti substrates by pulsed laser deposition (PLD). The apparent chemical diffusion coefficients of lithium in the films, , were measured by cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT), and electrochemical impedance spectroscopy (EIS). The average values calculated from CV results were in the order of 10⁻¹⁴ cm² s^–1. The values obtained by GITT, and EIS techniques were in the range of 10^–14–10^–18 cm² s^–1, 10^–14–10^–18 cm² s^–1, respectively. The values obtained by the two methods show a minimum point at x ∼ 0.5 for Li_1−xFePO₄. However, the overpotential values of the LiFePO₄ thin film electrodes obtained from the GITT results and the diffusion impedance deduced from the impedance spectra also show the minimum values at x ∼ 0.5 for Li_1–xFePO₄. This contradict could be caused by the improper use of GITT and EIS techniques for measuring the chemical diffusion coefficient of Li in Li_1–xFePO₄ which constitutes two phase, i.e., LiFePO₄ and FePO₄ in this region.     

The role of structural and electronic alterations on the lithium diffusion in LixCo0.5Ni0.5O2

The mechanisms for lithium diffusion in Li_xCo_0.5Ni_0.5O₂ were investigated using the galvanostatic intermittent titration technique (GITT). Membrane electrodes prepared with poly(vinylidene fluoride) and carbon black were employed in this study. The measured Brunauer-Emmett-Teller (BET) area of the Li_xCo_0.5Ni_0.5O₂ powder was combined with the GITT data to obtain the lithium chemical diffusion coefficient (), the lithium self-diffusion coefficient (D_Li⁺) and the thermodynamic factor (Φ) as a function of Li concentration (x). All three parameters vary non-monotonically with x. A minimum in and D_Li⁺ at x=0.5, along with structural changes, suggests the formation of a lithium superlattice at that concentration. The behavior of is complex but for x<0.34 it eventually undergoes a continuous decrease due to the metallic character of Li_xCo_0.5Ni_0.5O₂. We attribute the limitation of the specific reversible capacity of Li_xCo_0.5Ni_0.5O₂ to this decrease in and to elevated electrode voltages. Li transport in Li_xCo_0.5Ni_0.5O₂ is analyzed taking the variations in the cell parameters and the oxidation states of the Ni, Co and O ions into account.     

Li-ion diffusion kinetics in LiFePO4 thin film prepared by radio frequency magnetron sputtering

LiFePO₄ thin films were prepared by radio frequency (RF) magnetron sputtering and were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and atomic force microscope (AFM). Li-ion chemical diffusion coefficients, , were measured by potentiostatic intermittent titration technique (PITT), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The effects of Ag content, film thickness, and film orientation on the electrochemical performance and Li-ion chemical diffusion coefficients of the LiFePO₄ thin films were investigated. values were measured using the liquid electrolyte and the solid electrolyte, and the obtained values were discussed. The values by PITT and EIS were in the range of 10⁻¹⁴ to 10⁻¹² and 10⁻¹⁵ to 10⁻¹² cm² s⁻¹, respectively and that by CV was in the order of 10⁻¹⁴ cm² s⁻¹.     

Lanthanum-doped LiCoO2 cathode with high rate capability

Lanthanum-doped LiCoO₂ composite cathode materials, containing 0.1-10 mol% of La were synthesized by citric acid aided combustion technique. Thermal analyses showed that the sharp decomposition reaction for pristine LiCoO₂ became sluggish upon addition of lanthanum. X-ray diffraction analyses of the composites revealed existence of minute quantities of lanthanum-rich perovskite phases—rhombohedral LaCoO₃ and tetragonal La₂Li_0.5Co_0.5O₄ (14/mmm), along with rhombohedral LiCoO₂. Electron microscopy showed a distinct grain growth with increasing La content. An increase of about two orders of magnitude in the electrical conductivity (1.09 × 10⁻³ S cm⁻¹) was observed for 1.0 mol% La-doped LiCoO₂. An excellent cycling performance with capacity retention by a factor of ∼10 in comparison to the pristine LiCoO₂ was observed for the composite cathode containing 5.0 mol% La, when 2032 type coin cells were cycled at 5C rate. This has been ascribed to the structural stability induced by La doping and presence of the ion-conducting phase La₂Li_0.5Co_0.5O₄ which acts as a solid electrolyte for Li⁺ ions. A negligible growth of impedance upon repeated cycling has been observed. Cyclic voltammetry showed a remarkable improvement in reversibility and stability of the La-doped electrodes. These composite cathodes might be very useful for high rate power applications.     

Synthesis and peculiarities of electric properties of Li1.3Zr1.4Ti0.3Al0.3(PO4)3 solid electrolyte ceramics

The solid electrolyte Li_1.3Zr_1.4Ti_0.3Al_0.3(PO₄)₃ compound was synthesized by a solid-state reaction. The ceramic samples were sintered 1, 2 and 3 h and studied by X-ray and complex impedance spectroscopy in the frequency range from 10⁶ to 1.2 × 10⁹ Hz in temperature range from 300 to 600 K. The investigated compound at room temperature belongs to rhombohedral symmetry (s.g. ) with six formula units in the lattice. Two regions of relaxation dispersion were found. The dispersions are related to the fast Li⁺ ion transport in the grain and grain boundaries of ceramics. Varying of the sintering time affects the density of the ceramics, the values of total conductivity and its activation energy. The values of grain conductivity, its activation energy, and relaxation frequency in grain, dielectric permittivity and dielectric losses are independent from sintering duration of the ceramics. The value of activation energy of grain conductivity and activation energy of relaxation frequency is the same. That can be attributed to the fact that the temperature dependence of the grain conductivity is caused only by the mobility of Li⁺ ions, while a number of charge carriers remains constant with temperature.     

Investigation on diffusion behavior of Li in LiFePO4 by capacity intermittent titration technique (CITT)

Capacity intermittent titration technique (CITT) was used to investigate the chemical diffusion coefficient () of lithium-ion in LiFePO₄ cathode material. The values of at the galvano-charge current of 0.2 and 0.4 mA were respectively found to range from 8.8 × 10⁻¹⁶ to 8.9 × 10⁻¹⁴ cm² s⁻¹ and from 1.2 × 10⁻¹⁶ to 8.5 × 10⁻¹⁴ cm² s⁻¹ in the voltage range from 3.2 to 4 V (vs. Li⁺/Li). The transfer coefficients of cathode (0.32-0.42) and anodic (0.26-0.3), and the standard rate constant (1.58 × 10⁻⁹ to 1.30 × 10⁻⁸ cm s⁻¹) were measured from the Tafel plots of LiFePO₄ in the equilibrium potential range from 3.06 to 3.45 V. From these kinetic parameters, the finite kinetics at interface was taken into account to revise the above values of . The revised values of at the galvano-charge current of 0.2 and 0.4 mA were respectively found to range from 2.44 × 10⁻¹⁵ to 2.21 × 10⁻¹³ cm² s⁻¹ and from 5.81 × 10⁻¹⁶ to 3.22 × 10⁻¹³ cm² s⁻¹ in the voltage range from 3.2 to 4 V. Results show that the approximation of infinite charge-transfer kinetics leads to a spurious value of which is lower than the revised value, and the spurious extent depends on the galvano-charge current of CITT experiment.     

Carbon coated Li3V2(PO4)3 cathode material prepared by a PVA assisted sol-gel method

Carbon coated Li₃V₂(PO₄)₃ cathode material was prepared by a poly(vinyl alcohol) (PVA) assisted sol-gel method. PVA was used both as the gelating agent and the carbon source. XRD analysis showed that the material was well crystallized. The particle size of the material was ranged between 200 and 500 nm. HRTEM revealed that the material was covered by a uniform surface carbon layer with a thickness of 80 Å. The existence of surface carbon layer was further confirmed by Raman scattering. The electrochemical properties of the material were investigated by charge-discharge cycling, CV and EIS techniques. The material showed good cycling performance, which had a reversible discharge capacity of 100 mAh g⁻¹ when cycled at 1 C rate. The apparent Li⁺ diffusion coefficients of the material ranged between 9.5 × 10⁻¹⁰ and 0.9 × 10⁻¹⁰ cm² s⁻¹, which were larger than those of olivine LiFePO₄. The large lithium diffusion coefficient of Li₃V₂(PO₄)₃ has been attributed to its special NASICON-type structure.     

Oxygen reduction mechanism on copper in a 0.5 M H2SO4

The mechanism of the oxygen reduction reaction (ORR) in a naturally aerated stagnant 0.5 M H₂SO₄ was studied using electrochemical methods. The cathodic polarization curve showed three different regions; electrochemical impedance spectroscopy (EIS) measurement was used accordingly. The EIS data were analyzed, and the mechanism for the ORR was proposed consequently. The three regions include a limiting current density region with the main transfer of 4e⁻ controlled by diffusion (−0.50 V < E < −0.40 V), a combined kinetic-diffusion region (−0.40 V < E < −0.20 V) with an additional 2e⁻ transfer due to the adsorption of the anions, and a hump phenomenon region (−0.20 V < E < −0.05 V), in which the chemical redox between the anodic intermediate and the cathodic intermediate , together with the electrochemical reaction, synergistically results in the acceleration of the ORR. Therefore, a coupled electrochemical/chemical process (the EC mechanism) in the hump phenomenon region was proposed, and a good agreement was found between the experimental and fitted results. The EC mechanism was confirmed by the deaerated experiments.     

Particle size effect of Li[Ni0.5Mn0.5]O2 prepared by co-precipitation

Spherical (Ni_0.5Mn_0.5)(OH)₂ with different secondary particle size (3 μm, 10 μm in diameter) was synthesized by co-precipitation method. Mixture of the prepared hydroxide and lithium hydroxide was calcined at 950 °C for 20 h in air. X-ray diffraction patterns revealed that the prepared material had a typical layered structure with space group. Spherical morphologies with mono-dispersed powders were observed by scanning electron microscopy. It was found that the layered Li[Ni_0.5Mn_0.5]O₂ delivered an initial discharge capacity of 148 mAh g⁻¹ (3.0-4.3 V) though the particle sizes were different. Li[Ni_0.5Mn_0.5]O₂ having smaller particle size (3 μm) showed improved area specific impedance due to the reduced Li⁺ diffusion path, compared with that of Li[Ni_0.5Mn_0.5]O₂ possessing larger particle size (10 μm). Although the Li[Ni_0.5Mn_0.5]O₂ (3 μm) was electrochemically delithiated to Li_0.39[Ni_0.5Mn_0.5]O₂, the resulting exothermic onset temperature was around 295 °C, of which the value is significantly higher than that of highly delithiated Li_1−δCoO₂ (∼180 °C).     

Internal cation mobility in molten LiCl-NdCl3 system

Internal mobilities of Li⁺ and Nd³⁺ cations have been investigated in binary unsymmetrical molten LiCl-NdCl₃ system by countercurrent electromigration method (so-called Klemm method). The results have been presented as isotherms of cation internal mobilities versus equivalent fraction of NdCl₃ for 1023, 1073 and 1123 K and have been compared with corresponding relationships for NaCl-NdCl₃ and KCl-NdCl₃ systems. It has been found that internal mobility of Nd³⁺ ions (as well as Li⁺) increases with decreasing concentration of NdCl₃, contrary to KCl-NdCl₃ and NaCl-NdCl₃ systems for which Nd³⁺ internal mobility decreases or is nearly constant, respectively. The tendency that smaller alkali metal cation enhances internal mobility of trivalent ion (b_Ln) has been described with a simple equation: , where is the internal mobility of Ln³⁺ in molten LnCl₃, yLnCl₃ the equivalent fraction of LnCl₃ and a parameter is the difference between internal mobility of Ln³⁺ cation in molten LnCl₃ and internal mobility of this cation in infinitely diluted solution of LnCl₃ in alkali metal chloride.     

Relative stabilities of Ce(IV) and Ce(III) limiting carbonate complexes at 5-50 °C in Na aqueous solutions, an electrochemical study

The normal potential of the Ce(IV)/Ce(III) redox couple was determined by square wave voltammetry (SWV) at different temperatures in solutions with a constant ratio [CO₃²⁻]/[HCO₃⁻] ≈10 for high ionic strengths (3.29 mol dm⁻³ at 4.39 mol dm⁻³): varies from 259.5 to 198.0 mV/S.H.E. in the 15-50 °C range. Linear variations were found for versus (RT/F)ln(mCO₃²⁻), leading to the stoichiometry, Ce(CO₃)₆⁸⁻ for the Ce(IV) limiting complex. But the slopes of these linear variations were actually found in the range 1.8-1.9, not exactly 2. This was interpreted as dissociation of the Ce(IV) limiting complex following the reaction: Ce(CO₃)₅⁶⁻ + CO₃²⁻ → Ce(CO₃)₆⁸⁻ and as dissociation of the Ce(III) limiting complex following the reaction: Ce(CO₃)₃³⁻ + CO₃²⁻ → Ce(CO₃)₄⁵⁻; for which maximum possible values of log₁₀ K_IV,6 and log₁₀ K_III,4 were estimated via fitting in the 15-50 °C temperature range (log₁₀ K_IV,6 = 0.42 (0.97) and log₁₀ K_III,4 = 0.88 (7.00) at 15 °C (50 °C). The normal potential was found to decrease linearly with T, these variations correspond to , with T⁰ = 298.15 K and . The apparent diffusion coefficient of Ce(IV) was determined by direct current polarography (DCP), cyclic voltammetry (CV) and square wave voltammetry. It was found to depend on the ionic strength and to be proportional to T.     

Li diffusion in LiNi0.5Mn0.5O2 thin film electrodes prepared by pulsed laser deposition

Kinetic and transport parameters of Li ion during its extraction/insertion into thin film LiNi_0.5Mn_0.5O₂ free of binder and conductive additive were provided in this work. LiNi_0.5Mn_0.5O₂ thin film electrodes were grown on Au substrates by pulsed laser deposition (PLD) and post-annealed. The annealed films exhibit a pure layered phase with a high degree of crystallinity. Surface morphology and thin film thickness were investigated by field emission scanning electron microscopy (FESEM). The charge/discharge behavior and rate capability of the thin film electrodes were investigated on Li/LiNi_0.5Mn_0.5O₂ cells at different current densities. The kinetics of Li diffusion in these thin film electrodes were investigated by cyclic voltammetry (CV) and galvanostatic intermittent titration technique (GITT). CV was measured between 2.5 and 4.5 V at different scan rates from 0.1 to 2 mV/s. The apparent chemical diffusion coefficients of Li in the thin film electrode were calculated to be 3.13 × 10⁻¹³ cm²/s for Li intercalation and 7.44 × 10⁻¹⁴ cm²/s for Li deintercalation. The chemical diffusion coefficients of Li in the thin film electrode were determined to be in the range of 10⁻¹²-10⁻¹⁶ cm²/s at different cell potentials by GITT. It is found that the Li diffusivity is highly dependent on the cell potential.     

Synthesis and characterization of LiNi1/3Mn1/3Co1/3O2 by wet-chemical method

A series of LiNi_1/3Mn_1/3Co_1/3O₂ samples with α-NaFeO₂ structure belonging to the D_3d⁵ space group were synthesized using tartaric acid as a chelating agent by wet-chemical method. Different acid to metal-ion ratios R have been used to investigate the effect of this parameter on the physical and electrochemical properties. We have characterized the reaction mechanism, the structure, and morphology of the powders by TGA, XRD, SEM and TEM imaging, completed by magnetic measurements, Raman scattering spectroscopy, and complex impedance experiments. We find that the LiNi_1/3Mn_1/3Co_1/3O₂ sintered at 900 °C for 15 h with an acid to metal-ion ratio R = 2 was the optimum condition for this synthesis. For this optimized sample, only 1.3% of nickel-ions occupied the 3b Wyckoff site of the lithium-ions sublattice. The electrochemical performance has been investigated using a coin-type cell containing Li metal as the anode. The electronic performance is correlated to the concentration of the Ni(3b) defects that increase the charge transfer resistance and reduce the lithium diffusion coefficient. The optimized cell delivered an initial discharge capacity of 172 mAh g⁻¹ in the cut-off voltage of 2.8-4.4 V, with a coulombic efficiency of 93.4%.     

Study on physical and electrostatic interactions of counterions in poly(perfluorosulfonic) acid matrix: Characterization of diffusion properties of membrane using radiotracers

The self-diffusion coefficients of water and ions were used to study the physical (tortuosity) and electrostatic interactions of counterions in poly(perfluorosulfonic) acid membrane (Nafion-117) matrix. The self-diffusion coefficients of water were measured in the water swollen Nafion-117 membrane with Zn²⁺, Ca²⁺, Sr²⁺, and Fe²⁺ counterions by analyzing the experimental exchange rates between tritium tagged water (HTO) in membrane and equilibrating water. In order to study the effects of equilibrating solution, the HTO-desorption rate profiles between the membrane samples in H⁺ or Cs⁺ forms and equilibrating solution containing CsCl or HCl (0.25 mol/L) were measured. It was observed that the HTO-exchange rate profile was slower in case of membrane sample in Cs⁺-from equilibrated with salt/acid solution than that equilibrated with deionized water in same ionic form. However, HTO-exchange rate profile did not alter in case of H⁺-form of membrane on equilibration with salt or acid solution. The variation of ln  with polymer volume function V_p/(1 − V_p), where V_p is polymer volume fraction, indicated that: (i) in the membrane with multivalent counterions was lower than that reported for membrane with monovalent counterions at same V_p, and (ii) the linear trends observed in variation of ln  with V_p/(1 − V_p) for multivalent and monovalent counterions were significantly different. The values of in membrane normalized with at V_p = 0 were taken as an estimate of the tortuosity factor for self-diffusion of ions in the membrane matrix. The self-diffusion coefficients of ions reported in the literature along with tortuosity factor obtained from in the corresponding ionic forms of the membrane were analyzed to obtain the charge (Z_i) independent electrostatic interaction parameter g(φ) of monovalent and divalent ions in the membrane. This analysis indicated that g(φ) also vary exponentially as a function of V_p/(1 − V_p) irrespective of charge on counterions. In order to study the influence of V_p on diffusional transport rates of Na⁺ and Cs⁺ ions in membrane, a permeation experiment was carried out using H⁺-form of membrane having high water volume fraction. The diffusional transport rates of Cs⁺ and Na⁺ in H⁺-form of membrane were found to be similar indicating that the water volume fraction in membrane has strong influence on the parameters that govern the diffusion across the Nafion-117 membrane.     

Evaluation of electrical energy per order (EEO) with kinetic modeling on the removal of Malachite Green by US/UV/H2O2 process

The kinetics of decolorization of Malachite Green (MG) as a model cationic dye from textile industry, by US/UV/H₂O₂ process, was investigated with nonlinear regression analysis. The experimental results indicated that the decolorization kinetics of MG in this process fit well by pseudo-first order kinetics. With nonlinear regression analysis a model was developed for pseudo-first order constant (k_ap) as a function of operational parameters such as initial concentrations of H₂O₂ (25-600 mg l^− 1) and MG (1.82-9.87 mg l^− 1), temperature (294-307 K) and power density (0.049-0.16 W ml^− 1) as following:

     

Electrochemical behaviour of americium ions in LiCl-KCl eutectic melt

This work presents a study on the electrochemical properties of AmCl₃ in a molten LiCl-KCl eutectic, at a temperature range of 733-833 K. Transient electrochemical techniques, such as cyclic voltammetry and chronopotentiometry, on inert metallic tungsten working electrode have been used to investigate the reduction mechanism of Am³⁺ ions. The results show that Am³⁺ is reduced to Am metal by a two-step mechanism corresponding to the Am³⁺/Am²⁺ and Am²⁺/Am⁰ transitions. Formal standard potentials of Am³⁺/Am²⁺ ( versus Cl₂/Cl⁻ at 733 K) and Am²⁺/Am⁰ ( versus Cl₂/Cl⁻ at 733 K) redox couples as well as diffusion coefficients of Am³⁺ and Am²⁺ (2.4 × 10⁻⁵ and 1.15 × 10⁻⁵ cm² s⁻¹ at 733 K, respectively) have been calculated at three different temperatures. In the studied range of temperature, the DAm3+/DAm2+ ratio was found to be around 2. In addition, thermodynamic properties have been calculated for Am³⁺ () and Am²⁺ () and compared to thermodynamic reference data in order to estimate activity coefficients (Am³⁺ = 4.7 × 10⁻³ and Am²⁺ = 2.7 × 10⁻² at 733 K) in the molten LiCl-KCl eutectic.