共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
通过Moldflow软件对玻璃纤维增强聚丙烯(PP)复合材料电动车箱盖注射成型塑件的成型过程进行模拟分析;第一步按照常规方法找到最佳浇口位置,确定对比参数, 得到平均玻璃纤维取向值为0.9956;第二步再通过设置不同的浇口位置,得到玻璃纤维在制品中的最佳取向值,最佳浇口位置的平均玻璃纤维取向值为0.9992;根据此最佳浇口位置所得到的拉伸模量云图和泊松比云图的数值可以进一步验证此浇口位置为最佳浇口位置。结果表明,常规方法所分析的最佳浇口位置,不一定是最佳浇口位置,要通过不同的条件进行验证才能得到最佳的结果。 相似文献
3.
4.
采用Moldflow软件对注射成型纤维增强热塑性塑料的拉伸试样进行模拟研究.详细分析了注塑成型拉伸试样的纤维取向结构及由此引起的机械性能变化.分析表明:试样标距位置的纤维平均取向较好、皮芯结构不明显,标距外的两端部及两过渡位置的纤维平均取向不佳、皮芯结构较为明显;试样的物理性能参数受到取向影响而呈现各向异性.结合纤维取向分析、拉伸模量分析及泊松比分析,对注射法成型拉伸试样的方法进行初步探讨. 相似文献
5.
6.
马睿 《合成材料老化与应用》2019,48(4)
采用Moldflow软件对碳纤维复合材料的注塑成型过程进行模拟,并结合Folgar-tucker模型对脱模后的注塑成型碳纤维复合材料的残余应力、温度、弹性模量、泊松比和热膨胀系数等进行模拟。结果表明,纤维不同位置的取向张量不同,浇口位置和纤维末端的取向程度低于中间部分;无论浇口位置如何改变,纤维取向都会与熔体流动方向趋于相同;皮层的取向张量不会因为浇口位置改变而发生明显变化;碳纤维复合材料的边部区域的残余应力和温度与芯部不同;弹性模量E1和弹性模量G12分布与碳纤维取向呈正相关性;碳纤维取向程度对泊松比和热膨胀系数的影响较小,碳纤维复合材料各区域的泊松比和热膨胀系数分布相对均匀。 相似文献
7.
采用静电纺丝技术,利用改进接收装置,制备了取向的聚丙烯腈(PAN)膜,并且,通过热拉伸处理,使其具有更高的取向度。采用聚烯烃热塑性树脂(POE)渗透PAN纤维膜,制备了一系列非取向及取向度不同的PAN膜增强POE复合材料。采用红外光谱(IR)、热重(TG)等分析方法对样品进行了表征,并且,研究了其力学性能。热拉伸处理后的PAN/POE复合材料与纯POE材料相比,屈服强度和模量分别增大了129%、211%,而断裂伸长率减小了89%。当增强材料PAN含量为6.7%时,PAN/POE复合材料力学性能最佳。采用扫描电镜(SEM)和拉曼成像法研究了复合材料的形貌特征和增强机制,结果表明,随着取向的增加,POE树脂和PAN纤维之间的相容性更好,复合材料的屈服强度和模量增大。 相似文献
8.
9.
《化纤文摘》1996,(4)
,64160热处理对主链上有柔性链单元的热致性液晶聚醋初生纤维性能的影响K和n 5.K.…;Eur.Poz脚.J.,1994,30,(9),p.1081一1 088(英)分子中含有4,4,一对苯二甲酸二苯醋中间相单元,以及含有癸甲撑和己甲撑两种柔性间隔基的半柔性热致液晶聚酝,是由4,4,一二经基一1,10一二苯氧基链烷和对苯二甲酞氯,在变化主链上主链中上述两种脂肪墓单元之比的不同条件下反应制得。该聚酣的初生纤维随着喷头拉伸比的增加,显示了较好的取向和较高的模量。以低喷头拉伸比纺制的热处理过的纤维,模量和抗张强度均有提高;而以高喷头拉伸比纺出的初生纤维,经热处理… 相似文献
10.
对共聚芳砜酰胺(PSA)初生纤维进行5级热拉伸,研究了不同拉伸级数下PSA纤维的力学性能、动态力学性能、结晶度、晶区取向度以及片晶结构的变化。结果表明:热拉伸前后的PSA纤维都在425℃左右开始发生分解,热拉伸前后纤维的玻璃化转变温度(Tg)从375℃降为365℃;随着热拉伸的进行,纤维的断裂强度逐步增大,低于Tg进行热拉伸,纤维超分子结构没有明显变化,只发生非晶区的取向;高于Tg进行热拉伸,大分子发生显著的取向和结晶,并形成片晶结构,无定型区沿轴向尺寸增大;纤维经过5级拉伸后,其断裂强度和初始模量分别提高到2.02 cN/dtex和31.88 cN/dtex。 相似文献
11.
CFCC用补强纤维及纤维涂层 总被引:1,自引:0,他引:1
补强纤维对连续纤维补强陶瓷复合材料(CFCC)的性能起着至关重要的作用。本文介绍了目前CFCC所用补强纤维的种类及特性,并介绍了纤维涂层在CFCC补强和增韧过程中的作用以及涂层的涂覆方法。 相似文献
12.
13.
14.
15.
Dielectrophoresis is the motion of an uncharged particle in a nonuniform electric field. Using prolate spheroids to model cylindrical fibers, we find that the theoretical dielectrophoretic velocity of a conducting fiber in an insulating medium is proportional to the square of the fiber length and is virtually independent of fiber diameter. This prediction has been verified experimentally using aluminum wire particles 0.5–5 mm long and 25–75 μm in diameter moving in the space between cylindrical electrodes in a medium of mineral oil. The results point to the development of a fiber length classifier based on dielectrophoresis. 相似文献
16.
17.
H. Brody 《应用聚合物科学杂志》1978,22(6):1631-1641
The recovery portions of the stress–strain cycles of poly(ethylene terephthalate), poly(tetramethylene terephthalate), nylon 66, poly(vinyl chloride), and rayon were analyzed and shown to be superposable if appropriate horizontal and vertical shifts are made. The recovery curves are postulated to represent the stress–strain behavior of an elastomeric portion of the fiber which controls recovery, and the scaling factors necessary for superposition are interpreted as indicating changes in the “length” and “modulus” of the elastomer. The elastomer modulus correlates very well with the slope of the stress–strain curve, showing that the elastomer governs the fiber stress during extension. Temporary set is assumed to be due to a temporary localized ordering of the elastomer modulus, which disappears when stress is completely removed. This local ordering lowers the elastomer modulus, which leads to yield points in the stress–strain curves. Permanent set is initiated just before the temporary set approaches a constant value and increases at almost the same rate as the rate of extension. It is completely recovered by heating to near the Tg. 相似文献
18.
19.