Improving glass transition temperature of unsaturated polyester thermosets: Conventional unsaturated polyester resins

Highly crosslinkable unsaturated polyester resins (UPR) have attracted many interests in the application as reinforced matrix materials. Here, we present a systematical study of the influence of different curing conditions and styrene concentrations on resin viscosity and dynamic-mechanical properties of the thermoset. The pure maleic Palapreg® P18-03 was selected as model UPR because of its broad industrial use. By applying newly developed thermal curing profiles (without thermal initiators) and by raising the styrene content, the T_g of the network could be increased up to 206/215°C (1/10 Hz). For the first time, a fast curable UPR based on propylene glycol and neopentyl glycol with a T_g of up to 215°C is described. A partial substitution of problematic styrene with methylmethacrylate, tert-butylacrylate, and maleic anhydride (MA) was studied as well. MA leads to significantly improved resin reactivity. A resin containing 42 wt% styrene and 8 wt% MA yields thermosets with remarkably improved mechanical properties and with a narrower glass transition range compared to the original P18-03.     

Thermal and dynamic mechanical properties of polyethylene glycol/quartz composites for phase change materials

Polyethylene glycol (PEG)/quartz (denoted as BP/Q) composites have been investigated as candidates of phase change materials (PCMs) due to their thermomechanical properties around the glass transition temperature as well as thermal properties between 30 and 600 °C. Quartz (q-SiO₂) powders were extracted from local sand in Tanah Laut, Pelaihari, South Kalimantan, Indonesia. The composites were prepared by dispersing q-SiO₂ powders in the PEG matrix followed by the wet mixing process. The thermal properties of the composites were characterized using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), while the thermomechanical properties were examined using a dynamic mechanical analyzer (DMA) in a three-point bending mode around the PEG glass transition temperature range (−100–50°C). The morphology and interface bonding were investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the DSC measurement, the endothermic peak of the composites showed a shift of approximately 7–12 °C toward higher temperatures than that of the pure polymer. The melting enthalpy values (ΔH_m) of the BP/Q composites covered the required PCM application range, that is, between 139 and 182 J/g. The TGA of the composites showed that thermal degradation occurs in the range of 250–450 °C. We found that solid–solid PCMs (ssPCMs) were successfully fabricated with the addition of 10 and 20 wt% q-SiO₂. From DMA characterization, the BP/Q 20 wt% composite exhibited the maximum E’ and the minimum energy dissipation (E”). Its E’ value was approximately 250 MPa more than that of the pure PEG. The glass transition (T_g) temperatures of PEG and BP/Q composites (5, 10, and 20 wt%) were around −24.5, −19.1, −17.1, and − 5.3 °C, respectively. In addition, the E” and tan δ values decreased with q-SiO₂ filler content. Furthermore, the Cole-Cole plots of the BP/Q composites revealed a better interfacial bonding between the q-SiO₂ and the PEG matrix in the composites with higher silica content. A compact morphology was shown by the BP/Q 20 wt% composite due to high silica concentration. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48130.     

Elaboration and dielectric property of modified PZT/epoxy nanocomposites

Composites of lead zirconate titanate (PZT) 50 nm nanoparticles and epoxy resins have been produced with various PZT contents from 0 to 20 wt%. The morphology and thermal properties of prepared composites were characterized using scanning electron microscopy and differential scanning calorimetry. The PZT nanoparticles were found to be well dispersed in the epoxy resin matrix. The glass transition temperature (T_g) value of the nanocomposites increases from 164 to 178°C with increasing the PZT weight fraction. The dielectric composites properties dependences were studied via a wide range of frequency from 10 Hz to 100 kHz. The dielectric constant of PZT/epoxy composite was increased from 5.56 to 6.29 (at f = 1 kHz, T = 30°C), respectively to the incorporated PZT amount, and these values are higher than that the dielectric constant of pure cured epoxy resin, ε = 4.86. POLYM. COMPOS., 37:455–461, 2016. © 2014 Society of Plastics Engineers     

Dielectric and mechanical properties of poly(vinyl chloride)–dioctylphthalate systems

The mechanical properties, tensile strength, and elongation were investigated for poly(vinyl chloride) (PVC) samples mixed with dioctylphthalate (DOP) at concentrations from 0 to 100 parts per hundred parts PVC at 23°C. It was found that the tensile strength decreased with the increase of concentration, and the elongation was increased until a concentration of 30 DOP content, and then decreased. This leads to the suggestion that intermolecular plasticization is dominant until 30 DOP content, while interstructural plasticization is prevailing for higher concentrations. The permittivity ε′ and the dielectric loss factor ε″ of the same samples have been measured in the frequency range 10²–10⁵ Hz at temperatures from 3 to 96°C. Results show that as the DOP content increases in PVC, the dielectric absorption becomes broader, and the glass transition temperature T_g is lowered. The magnitude of the loss peak decreases with an increase of DOP content to a minimum at concentrations from 40 to 60 DOP content. At higher concentrations the loss peak is increased and T_g is unaltered. Another absorption was observed at 100 Hz and at high temperatures, which was attributed to Maxwell–Wagner effect or direct current conductivity or both of them. It was found that the sample containing 40 parts DOP in 100 parts PVC possesses the best mechanical and electrical properties.     

Quantitative study of the annealing of poly(vinyl chloride) near the glass transition

Poly(vinyl chloride) displays a normal DSC of DTA curve for the glass transition when quenched from above its T_g. However if cooled slowly or annealed near the glass transition temperature, a peak appears on the DSC or DTA curve at the T_g. In this paper quantitative studies of the time and temperature effects on the production of this endothermal peak during the annealing of PVC homopolymer and an acetate copolymer are presented. The phenomenon conforms to the Williams, Landell, and Ferry equation for the relaxation of polymer chains, the rate of the peak formation becoming negligible at more than 50°C below T_g. The energy difference between the quenched and annealed forms is small. For a PVC homopolymer annealed 2 hr at 68°C, which is T_g ?10°C, the difference is 0.25 cal/g. For a 13% acetate copolymer of PVC similarly annealed, the difference is 0.36 cal/g. The measured rates of the process give a calculated activation energy of 13–14 kcal/mole for PVC homopolymer and copolymer. This appearance of a peak on the T_g curve for a polymer when annealed near the glass temperature appears to be a general phenomenon.     

Mechanical,morphological, and thermal properties of poly(vinyl chloride)/low‐density polyethylene composites filled with date palm leaf fiber

This article investigates the mechanical, morphological, and thermal properties of poly(vinyl chloride) (PVC) and low‐density polyethylene (LDPE) blends, at three different concentrations: 20, 50, and 80 wt% of LDPE. Besides, composite samples that were prepared from PVC/LDPE blend reinforced with different date palm leaf fiber (DPLF) content, 10, 20, and 30 wt%, were also studied. The sample in which PVC/LDPE (20 wt%/80 wt%) had the greatest tensile strength, elongation at break, and modulus. The good thermal stability of this sample can be seen that T_10% and T_20% occurred at higher temperatures compared to others blends. DPLF slightly improved the tensile strength of the polymer blend matrix at 10 wt% (C10). The modulus of the composites increased significantly with increasing filler content. Ageing conditions at 80°C for 168 h slightly improved the mechanical properties of composites. Scanning electron microscopic micrographs showed that morphological properties of tensile fracture surface are in accordance with the tensile properties of these blends and composites. Thermogravimetric analysis and derivative thermogravimetry show that the thermal degradation of PVC/LDPE (20 wt%/80 wt%) blend and PVC/LDPE/DPLF (10 and 30 wt%) composites took place in two steps: in the first step, the blend was more stable than the composites. In the second step, the composites showed a slightly better stability than the PVC/LDPE (20 wt%/80 wt%) blend. Based on the above investigation, these new green composites (PVC/LDPE/DPLF) can be used in several applications. J. VINYL ADDIT. TECHNOL., 25:E88–E93, 2019. © 2018 Society of Plastics Engineers     

Dynamic mechanical signatures of a polyester‐urethane and plastic‐bonded explosives based on this polymer

The complex shear moduli of the segmented polyurethane Estane 5703p, Livermore explosive (LX)‐14, and plastic bonded explosive (PBX)‐9501, which use this polymer as a binder, have been investigated. Segmented polyurethanes, such as Estane 5703, contain microphase‐separated hard segments in a rubbery matrix of soft segments. LX‐14 is composed of 95.5% 1,3,5,7‐tetranitroazacyclooctane (HMX) explosive with 4.5% Estane 5703 binder. PBX‐9501 is composed of 94.9% HMX, 2.5% Estane 5703p binder, 2.5% nitroplasticizer (NP), and about 0.1% antioxidant Irganox 1010. In the temperature range from ?150 to 120°C, two relaxations were observed as peaks in the loss modulus and tangent delta in Estane 5703p and LX‐14. A third relaxation was found in PBX‐9501. The low temperature relaxation associated with vitrification of the poly(ester urethane) soft segment occurred in the shear loss modulus (G″) at ?29 and ?26°C in Estane and LX‐14, respectively, at 1 Hz. In PBX‐9501 the Estane soft segment glass transition peak, T_g(SS), in the loss modulus occurred at ?40 ± 3°C at 1 Hz. The reduction in soft segment glass transition in PBX‐9501 is clear evidence of plasticization of the soft segment by NP. The apparent activation energy of the maximum in the loss modulus for LX‐14 and PBX‐9501 over the frequency range from 0.1 to 10 Hz was 230 kJ/mole (55 kcal/mole). The hard segment glass transition, T_g(HS), was observed as a peak in the loss modulus at about 70°C. In LX‐14 the transition was observed at lower temperatures (56–58°C at 1 Hz) depending on thermal history. There was a low temperature shoulder on the T_g(HS) of Estane 5703 associated with soft segment crystallinity. Modulated differential scanning calorimetry (MDSC) was used to verify the T_g(HS) in Estane and 50/50 mixtures of Estane with NP. In PBX‐9501 the hard segment glass transition occurred between 65 and 72°C. The presence of NP in PBX‐9501 gave rise to a new transition, T_eu(NP), between 8 and 15°C. This peak is believed to be associated with the eutectic melting of the plasticizer. Returns of fielded PBX‐9501 that were 6 and 11 years old were also measured. Small variations in T_g(SS) and the rubber plateau modulus were observed in these aged samples, consistent with migration of plasticizer and/or very low levels of chain scission. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1009–1024, 2002     

Relaxation behavior and activation energy of relaxation for polyimide and polyimide–graphene nanocomposite

The relaxation behavior of polyimide and its nanocomposite containing 10 wt % of graphene was studied by using the dynamic mechanical spectrometer. Dynamic mechanical analysis of polyimide and its composite was performed as a function of temperature and frequency in the temperature range of 25–480 °C and frequency range between 0.05 and 100 Hz. The effect of increasing frequency of testing from 0.05 to 100 Hz is a significant shift from the glass transition temperature, T_g, to higher temperature from 360 °C at 0.05 Hz to 420 °C at 100 Hz. The tan δ peak height for both α and β transitions decreased with increasing test frequency from 0.24 at 0.05 Hz to 0.08 at 100 Hz, due to increasing restriction to chain motion. At any given testing frequency, the T_g for the composite was shown to be higher than that for the matrix by about 5–10 °C. The Arrhenius equation was used to calculate the activation energy for both α and β transitions. The activation for α and β transitions for the composite and polyimide matrix were determined to be 688 and 537 kJ/mol and 313 and 309 kJ/mol, respectively, indicating that a significant increase in the energy barrier to chain relaxation occurred as a result of reinforcement of polyimide with low weight fraction of graphene. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43684.     

Synthesis and characterization of poly(ethylene oxide)‐based glycopolymers and their biocompatibility with osteoblast cells

Poly(ethylene oxide)‐block‐poly(methacryl‐d ‐glucopyranoside) (PEO‐GP) and poly(methacryl‐d ‐glucopyranoside) (H‐GP) glycopolymers were synthesized by deacetylation of acetylated polymers which were synthesized via atom transfer radical polymerization. The synthesized glycopolymers were characterized using ¹H NMR, ¹³C NMR and Fourier transform infrared (FTIR) spectroscopies, gel permeation chromatography (GPC), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The deacetylated polymers exhibited onset decomposition temperatures about 60 °C lower compared to the polymers having acetyl pendants. The glass transition temperature (T_g) of the acetylated homopolymer was 133 °C and that of the PEO‐based block copolymer was 124 °C. The deacetylated polymers H‐GP and PEO‐GP exhibited T_g values of about ?30 °C. Biocompatibility of the H‐GP and PEO‐GP glycopolymers was obtained by studying osteoblast cell adhesion, viability and proliferation in vitro. The cell viability showed an increase with increasing concentration of H‐GP from 0.1 to 1 µmol L^?1 and then decreased with further increase in its concentration (10–1000 µmol L^?1). PEO‐GP did not show a significant variation in cell viability on variation of its concentration from 0.1 to 1000 µmol L^?1. The significant improvement in biocompatibility with osteoblast cells in the presence of PEO‐GP was considered as due to the covalently bonded PEO segment of the methacrylate glycopolymer block. © 2014 Society of Chemical Industry     

Nanotailoring of polyurethane adhesive by polyhedral oligomeric silsesquioxane (POSS)

The development and commercialization of nanoparticles such as nanoclays (NCs), carbon nanotubes (CNTs) and polyhedral oligomeric silsesquioxanes (POSS) offers new possibilities to tailor adhesives at the nanoscale. Four types of POSS, with reactive mono-functional groups of isocyanatopropyl, glycidoxypropyl, aminoethyl and non-reactive octaphenyl, were incorporated in concentrations of 1, 3 and 5 wt% into a polyurethane (PU)-based adhesive. Thermo-mechanical bulk properties were studied using dynamic mechanical analysis (DMA). Adhesive properties were characterized in shear and peel modes. Atomic force microscopy (AFM) was used to study the nanoscale morphology. DMA measurements indicated that the neat PU possessed a glass transition temperature (T _g) of ≈ 30°C. The T _g of PU/POSS-glycidoxypropyl nanocomposite adhesive increased gradually with POSS concentration to 50°C for 5 wt%. PU/POSS-octaphenyl nanocomposite adhesive exhibited an increased T _g by 10°C for 5 wt%. The incorporation of POSS-isocyanatopropyl in the PU had no effect on the T _g. With respect to shear properties of POSS-octaphenyl-, POSS-isocyanatopropyl- and POSS-glycidoxypropyl-based PU nanocomposite adhesives, shear strength improved by 230, 178 and 137%, respectively, compared to neat PU. POSS-aminoethyl exhibited lower shear and peel strengths, while POSS-isocyanatopropyl provided the best balance of both higher shear and peel strengths compared to neat PU. It was concluded that the grafted functional group on the POSS and its reactivity with the PU network components were the decisive factors with respect to the thermo-mechanical, morphological and adhesive properties of the resulting nanocomposite adhesives. Consequently, the POSS/polyurethane based nanocomposite adhesives could be tailored for a large range of applications.     

Automated torsion pendulum analysis of the formation and properties of a polyphthalocyanine

The cure and transitions of a C₁₀ diamide phthalocyanine resin have been investigated by the torsional braid method. Two relaxations (T′ > T_g and T > T_g) occurring above the glass transition temperature (T_g) are shown to correspond to two relaxations which develop prior to vitrification on isothermal cure. They bear directly on processibility of the material. Also investigated was the coupling between a low temperature transition (～ ? 146°C/2.1 Hz) inherent to the material and a low temperature water-induced transition (～ ? 76°C/1.9 Hz).     

A water-soluble organic-inorganic hybrid material based on polyhedral oligomeric silsesquioxane and polyvinyl alcohol

A novel series of organic-inorganic hybrid materials involving cage-like octa(3-chloroammoniumpropyl)silsesquioxane and Polyvinyl alcohol (OCAPS/PVA) were prepared via solution blending method. The obtained hybrid films were optically transparent and soluble in water. OCAPS/PVA hybrids were characterized by FT-IR, wide-angle X-ray diffraction (WAXD) scanning electronic microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), differential scanning calorimetry (DSC), thermogravimetry analysis (TGA) and tensile test. The results showed that the hydrogen bond interactions were formed between OCAPS and PVA. OCAPS could be dispersed well in PVA matrix till its content was 10 wt%, while the aggregation and crystallization of OCAPS were observed when the content was up to 15 wt%. The glass transition temperature (T _g ) of OCAPS/PVA was found to increase from 53 °C to 60 °C, and the melting temperature (T _m ) decreased from 180 °C to 171 °C with increasing OCAPS content from 0 wt% to 15 wt%. The thermal stability of PVA main chain was improved by the addition of OCAPS and the thermal residue ratio also increased. The tensile strength of OCAPS/PVA decreased from 28 MPa to 19 MPa, while the elongation at break of hybrid films increased from 121% to 175%.     

High-Performance Low-k Poly(dicyclopentadiene) Nanocomposites as Achieved via Reactive Blending with Norbornene-Functionalized Larger POSS

Low dielectric constant (k) polymers with excellent comprehensive properties are useful materials in the microelectronics industry as matrix resins or encapsulation layers. With the inherent low polarization, high reactivity, good processability, and low cost, poly(dicyclopentadiene) (PDCPD) has received considerable attention as low-k materials. However, its practical application is limited by the relatively high thermal expansion and k value. Herein, three norbornene-functionalized polyhedral oligomeric silsesquioxanes (POSSs) with T₈, T₁₀, and T₁₂ polyhedral cores are synthesized and employed for enhancing the dielectric and comprehensive properties of PDCPD via reactive blending. The results show that these POSSs have good compatibility with PDCPD matrix and nano-dispersed POSSs particles could be obtained. As a result, the materials’ properties can be largely enhanced by varying the POSS content and POSS size. Especially, PT₁₂N₁₂-40 (40 wt% of T₁₂N₁₂) shows the lowest k value (2.1) and coefficient of thermal expansion (63.4 ppm°C⁻¹), highest glass transition temperature (202.5 °C), yield strength (78.0 MPa), and elastic modulus (2.36 GPa), along with excellent hydrophobicity. This study highlights a useful strategy to fabricate high-performance low-k polymer nanocomposites by using larger POSS and reactive blending, which provides useful materials for the future microelectronic industry and high frequency communication.     

Preparation and properties of polyhedral oligomeric silsesquioxane/epoxy hybrid resins

Octaaminophenyl polyhedral oligomeric silsesquioxane (OAPS) was synthesized using three‐step method and used to modify o‐cresol‐novolac epoxy resin (ECN) for printed circuit board. The influence of OAPS on the reactivity and the final properties of the hybrid networks were evaluated. The intercrosslinking reaction between ECN and OAPS was confirmed by Fourier transform infrared spectra. The ECN/OAPS hybrids have better impact strength, higher electrical resistivity and thermal stability, lower water absorption than the unmodified ECN. The volume resistivity and surface resistivity of the hybrids increase by an order of magnitude or more compared to the neat epoxy. The thermal stability of the hybrids improves by the incorporation of OAPS; the initial decomposition temperature and char yield show an increasing tendency up to 4 wt% loading of OAPS. The hybrids exhibit higher storage modulus and glass transition temperature (T_g) than the neat epoxy. The T_g of the hybrids greatly improves up to 153.3°C at 3 wt% content, much higher than 119.4°C of the neat epoxy. POLYM. COMPOS., 34:1753–1760, 2013. © 2013 Society of Plastics Engineers     

Characterization of PVC cable insulation materials and products obtained after removal of additives

Organic solvents cyclohexane, dichloromethane, hexane, and tetrahydrofuran were tested to separate the dioctylphthalate (DOP) as plasticizer from the poly(vinyl chloride) (PVC)‐based materials. It was found that the efficiency of ultrasound‐enhanced hexane extraction of the DOP from PVC is 70% and the efficiency of the separation of the DOP and other compounds from the PVC by dissolution in THF followed by subsequent precipitation was 98–99%. Differential scanning calorimetry (DSC) and thermogravimetry (TG) were used to characterize the thermal behavior of PVC materials before and after extraction of plasticizers. It was found that during heating in the range 20–800°C the total mass loss measured for the nontreated, extracted, and precipitated PVC samples was 71.6, 66.6, and 97%, respectively. In the temperature range 200–340°C, the release of DOP, HCl, and CO₂ was observed by simultaneous thermogravimetry (TG)/FTIR. The effect of plasticizers on thermal behavior of PVC‐based insulation material was characterized by DSC in the range ?40–140°C. It was found that, concerning the PVC cable insulation material before treatment, the value of the glass transition temperature (T_g) was 1.4°C, whereas for the PVC sample extracted by hexane, the value of T_g was 39.5°C and for the PVC dissolved in THF and subsequently precipitated, the value of T_g was 80.4°C. Moreover, the PVC samples after extraction of plasticizers, fillers, and other agents were tested to characterize their thermal degradation. The TG and FTIR results of chemically nontreated, extracted, and precipitated samples were compared. The release of DOP, HCl, CO₂, and benzene was studied during thermal degradation of the samples by FTIR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 788–795, 2006     

Thermomechanical behavior of poly(vinyl chloride) in the process of degradation

The thermomechanical behavior of poly(vinyl chloride) (PVC) was investigated during its thermal degradation by using torsional braid analysis. In thermomechanical behavior as a function of temperature, the relative rigidity G_r decreased initially with increasing temperature, then began to increase passing through a minimum at about 200°C, and finally decreased at 340°C. Increase in G_r from 200°C was caused by formation of a conjugated polyene chain accompanied by dehydrochlorination and by crosslinking reaction, and decrease in G_r at 340°C was related to scission reactions of the crosslinking network by oxidation. In the change in logarithmic decrement Δ, three peaks were observed: at 90°C, coinciding with the glass transition of the polymer; at about 200°C, due to the melting transition of crystallites, and at about 300°C, due to a loss of mechanical energy in the rheological transition of the polymer from a liquid state to a glassy state passing through a viscoelastic region. The thermomechanical properties of PVC with different molecular weights were also measured, and the effect of molecular weight G_r and Δ are discussed. In isothermal measurements of the relative rigidity in air, exponentially increasing curves were observed as a function of time. These curves were analyzed kinetically as a first-order reaction, and an activation energy of 22.7 kcal/mole was obtained.     

Preparation and thermal properties of bio‐based gallic acid epoxy/carbon nanotubes composites by cationic ring‐opening reaction

In order to prepare the bio‐based polymeric materials, a gallic acid epoxy resin (GA‐ER) is synthesized by using biodegradable gallic acid, and the nanocomposites of GA‐ER/glycidyl methacrylate (GMA)/multiwalled carbon nanotubes (MWCNTs) were prepared by dual hybrid cationic ring‐opening reaction. Differential scanning calorimetry (DSC) results show that the curing reaction temperature of the nanocomposites is between 150 and 225°C. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results suggest that MWCNTs are homodispersing in the GA‐ER/GMA matrix when the MWCNTs content is not more than 1.0 wt%. The glass transition temperature of the nanocomposite with 0.5 wt% MWCNTs is 9.3°C higher than that of pure resin system. The initial thermal degradation temperature and degradation activation energies E_a of the nanocomposite with 1.0 wt% MWCNTs is 10°C and 68.6 kJ/mol higher than that the pure resin system, respectively. POLYM. COMPOS., 37:3093–3102, 2016. © 2015 Society of Plastics Engineers     

Effects of hydrothermal ageing on the thermal behaviour of poly(vinyl chloride) filled with wood flour

The hydrothermal ageing of wood‐flour‐filled PVC produced by dry‐blending in a high‐speed mixer in the presence of a plasticizer and other processing additives was carried out to investigate its thermal behaviour, and the results obtained were compared with those for the unfilled material. The dry‐blended compounds were prepared as films by a calendering process. The accelerated hydrothermal ageing was carried out by immersing the samples in boiling water at 100 °C for 110 h. The thermal behaviour of the reference and the aged samples in water was characterized by differential scanning calorimetry (DSC) and determination of the weight changes. The study has shown that during hydrothermal ageing, the samples from the whole formulations absorbed water, for instance, for 30 wt% filled PVC (F30), 16 wt% of water absorption was obtained, while this was only 2.2 wt% for unfilled PVC (F0). It was also noticed that the formulations filled with wood flour up to 10 wt% exhibited similar water absorption kinetics, i.e. the water was mostly absorbed during the first 50 h and the amount absorbed was less than 5 wt%. On the other hand, the 30 wt% filled samples regularly absorbed water up to almost 16 wt% after 100 h of immersion. The DSC data showed that hydrothermal ageing significantly affected the onset temperature of decomposition (T_d) of the unfilled samples by decreasing this temperature from 228 to 215 °C. For the 30 wt% filled samples, only additive migration was observed, while the T_d remained almost unchanged. Furthermore, from the DSC data, processability of the 30 wt% filled PVC samples at elevated temperatures, i.e. 180 to 200 °C was shown. Copyright © 2004 Society of Chemical Industry     

Synthesis,characterization, and properties of a polyhedral oligomeric octadiphenylsulfonylsilsesquioxane

A novel polyhedral oligomeric octadiphenylsulfonylsilsesquioxane (ODPSS) was synthesized from octaphenylsilsesquioxane and benzenesulfonyl chloride via a Friedel–Crafts reaction with a high yield. ODPSS was identified by Fourier transform infrared spectroscopy, ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI–TOF MS), wide‐angle X‐ray diffraction, and elemental analysis to be a kind of polyhedral oligomeric silsesquioxane of a T₈R₈ structure. ODPSS exhibited superior thermal stability according to thermogravimetric analysis. Its initial thermal decomposition temperature (T_onset) was at 491°C in air and 515°C in nitrogen. Thermal and mechanical properties of epoxy resin (EP) composites with ODPSS added were studied by differential scanning calorimetry and tensile testing. The results show that the incorporation of ODPSS at a low loading content not only improved the glass‐transition temperature of the EP composites but also enhanced their tensile strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40892.     

Sustainable synthesis of bio‐based hyperbranched ester and its application for preparing soft polyvinyl chloride materials

In this study, bio‐based hyperbranched ester was synthesized from castor oil. The chemical structure of the bio‐based hyperbranched ester obtained was characterized with Fourier transform infrared and ¹H NMR spectra. Soft polyvinyl chloride (PVC) materials were prepared via thermoplastic blending at 160 °C using bio‐based hyperbranched ester as plasticizer. The performances including the thermal stability, glass transition temperature (T_g), crystallinity, tensile properties, solvent extraction resistance and volatility resistance of soft PVC materials incorporating bio‐based hyperbranched ester were investigated and compared with the traditional plasticizer dioctyl phthalate (DOP). The results showed that bio‐based hyperbranched ester enhanced the thermal stability of the PVC materials. The T_g of PVC incorporating bio‐based hyperbranched ester was 23 °C, lower than that of PVC/DOP materials at 28 °C. Bio‐based hyperbranched ester showed a better plasticizing effect, solvent extraction resistance and volatility resistance than DOP. The plasticizing mechanism is also discussed. © 2018 Society of Chemical Industry