A miniaturized multi‐wideband Quasi‐Yagi MIMO antenna system

A multi‐band directional multiple‐input–multiple‐output (MIMO) antenna system is presented based on a rectangular loop excited Quasi‐Yagi configuration. A 64% reduction in size is obtained using a rectangular meandered element as well as a small ground plane. The proposed two‐element MIMO antenna system covers the Telemetry L‐band and several LTE/WLAN bands. It has a wide measured bandwidth of 689 MHz (1.897–2.586 GHz) in the desired band centered at 2 GHz, and a measured bandwidth of more than 168 MHz across rest of the bands. The MIMO antenna system has a total size of 45 × 120 × 0.76 mm³, with a single element size of 55 × 60 × 0.76 mm³. The non‐desired back‐lobe radiation which is obtained using a small ground plane, is significantly reduced by using a novel defected ground structure (DGS) as compared with the complex techniques present in literature. The proposed DGS provides a high measured front‐to‐back ratio of 14 dB at 2 GHz and 11 dB in other bands. A maximum measured realized gain of 5.8 dBi is obtained in the desired band using a single parasitic director element. The proposed MIMO antenna system has a minimum measured radiation efficiency of 70%, isolation of 12 dB, and envelope correlation coefficient of 0.098 within all bands which ensures very good MIMO performance.     

Dual‐band quasi‐self‐complementary antenna for wireless local network operation

This article proposes a compact (6 × 21 × 0.4 mm³) antenna with dual‐band operation that satisfies the wireless local area network. To achieve optimal impedance matching for the lower and upper operating bands, the proposed antenna structure is designed as a quasi‐self‐complementary (QSC) type, in which the lower (2.4 GHz) operating band is excited through the loop‐like structure of the proposed antenna, whereas its self‐complementary counterpart (rectangular patch structure) induces the upper (5.2/5.8 GHz) operating band. Further investigation was also conducted by printing the proposed QSC antenna onto a flexible substrate of 0.063 mm in thickness. To cover both operating bands, the proposed flexible antenna was restructured to 20.5 × 8 mm². The design and initial characteristics of the two proposed antennas were discussed in detail via simulation, and the experimental results showed satisfactory performance of both operating bands. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:298–305, 2014.     

Design of ultrawide band planar inverted‐F antenna with slotted broad feed

This article presents a low ‐ profile planar inverted‐F antenna (PIFA) for broadband applications. The proposed antenna geometry is simple and does not use any parasitic elements, which makes its fabrication easier. The antenna's radiator is composed of a top loading plate, broad feed plate, and a shorting plate; occupies a total volume of (L × W × H ) 20 × 12 × 6 mm³. The proposed antenna design achieved the wideband characteristics by using the method of bringing resonances to proximity; furthermore, the low ‐ profile feature is achieved by removing some portion of the ground plane according to the volume ratio of PIFA. To validate the simulated results, an antenna prototype has been fabricated. The simulated and measured radiation patterns, gain, group delay, and simulated peak ‐ specific absorption rate (SAR) are presented. The measurement result demonstrates that the proposed antenna design achieved the maximum bandwidth of 142% (3.1–18.5 GHz) for |S ₁₁| ≤ ?10 dB.     

Dual ISM band printed antenna with omnidirectional radiation pattern and better radiation efficiency

Designing a high gain planar antenna on the low‐cost FR4 substrate is one of the major challenging tasks for the researchers. The omnidirectional radiation pattern is desired for 360° coverage. Both of these requirements have been addressed in this article. This article presents a dual band printed antenna designed on an FR4 substrate of 1.6 mm thickness. The proposed antenna operates in the ISM band of 2.4 and 5.8 GHz for the application of dual‐band WLAN/WIFI. The proposed antenna consists of a circular patch and ring‐shaped ground plane. The overall dimension of the antenna is 66 × 66 × 1.6 mm³. Excellent impedance matching and radiation efficiency for both the bands have been achieved. The proposed antenna shows omnidirectional radiation pattern at 2.4 GHz ISM band and nearly omnidirectional pattern along with high gain of 4.7 dBi at 5.8 GHz ISM band.     

Epsilon‐shaped circularly polarized strip and slot‐loaded ultra‐wideband antenna for Ku‐band and K‐band

A compact epsilon‐shaped (ε) ultra‐wideband (UWB) antenna for dual‐wideband circularly polarized (CP) applications has been investigated in this article. It consists of a stepped stub loaded modified annular ring‐shaped radiator and modified CPW ground plane. The ground plane is loaded with two semicircular notches and a spiral‐shaped slot. The impedance bandwidth (IBW) is 97.02% (10.4‐30 GHz) along with an overall footprint of 20 × 20 mm². The fractional axial ratio bandwidth (3‐dB ARBW) for two wide bands is 38.50% (13.30‐19.64 GHz) and 6.45% (26.25‐28.00 GHz), respectively. The proposed antenna is left‐hand circularly polarized with a peak gain of about 5.09 and 5.14 dB in both 3‐dB ARBW bands. The proposed antenna is dominating other reported CP antenna structures in terms of number of CP bands, 3‐dB ARBW, IBW, peak gain, and dimensions.     

Triple‐band metamaterial‐inspired antenna using FDTD technique for WLAN/WiMAX applications

In this article, a triple‐band metamaterial (MTM)‐inspired antenna has been designed and analyzed using finite difference time domain technique (FDTD). The proposed MTM consists of two L‐dumbbell‐shaped unit cells, feed, and partial ground plane. The proposed antenna shows triple‐band characteristics with impedance bandwidths of 10.6, 4.67, and 26.8% centered at 2.4, 3, and 5.7 GHz, respectively. The first two bands are working at zeroth‐order resonating mode and first‐order resonating mode while third is due to series slot and coupling between feed and ground plane. It offers compact nature with total antenna size of 30 × 30 × 1.6 mm³. The proposed triple‐band antenna has been designed and analyzed using FDTD code based on convolutional perfectly matched layer boundary conditions and HFSS as well. The prototype antenna has also been fabricated and tested experimentally to validate the simulation results. The proposed antenna exhibits good radiation characteristics throughout the working bands. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:688–695, 2015.     

Penta‐band notched ultra‐wideband monopole antenna loaded with electromagnetic bandgap‐structures and modified U‐shaped slots

In this article, a planar monopole penta‐notched ultra‐wideband (UWB) antenna is designed and investigated. Three notches (2.81 GHz radar surveillance, 3.38 GHz WiMAX, and 3.87 GHz C‐band satellite downlink) have been realized by integrating three modified U‐shaped slots on the radiating surface. Furthermore, to create two additional notches (2.33 GHz ISM band and 5.75 GHz WLAN), two meander line electromagnetic bandgap (EBG); one located near to the feed line and another on the radiating surface, have been introduced in the design. These unit cells play a fundamental role in generating notches at higher as well as lower frequencies. The proposed antenna possesses an overall size of 34.9 × 31.3 × 1.6 mm³ and has been designed over FR4 substrate. A 50 Ω microstrip line is used to feed the antenna. The antenna without any extra arrangement exhibits an impedance bandwidth of 7.6 GHz. A parametric analysis is studied in detail to observe the band rejection characteristics. The ANSYS HFSS simulation software is used for simulating the proposed design structures. For validation purpose, a prototype is fabricated and characterized. A very good agreement is achieved between simulated and measured results.     

Design and analysis of a quad‐band substrate‐integrated‐waveguide cavity backed slot antenna for 5G applications

A planar and compact substrate integrated waveguide (SIW) cavity backed antenna and a 2 × 2 multi‐input multi‐output (MIMO) antenna are presented in this study. The proposed antenna is fed by a grounded coplanar waveguide (GCPW) to SIW type transition and planned to be used for millimeter‐wave (mm‐wave) fifth generation (5G) wireless communications that operates at 28, 38, 45, and 60 GHz frequency bands. Moreover, the measured impedance bandwidth (|S₁₁| ≤ ? 10 dB ) of the antenna covers 27.55 to 29.36, 37.41 to 38.5, 44.14 to 46.19, and 57.57 to 62.32 GHz bands and confirms the quad‐band characteristic. Omni‐directional radiation characteristics are observed in the far‐field radiation pattern measurements of the antenna over the entire operating frequency. The reported antenna is compact in size (9.7 × 13.3 × 0.6 mm³) and the gain values at each resonance frequency are measured as 3.26, 3.28, 3.34, and 4.51 dBi, respectively. Furthermore, the MIMO antenna performance is evaluated in terms of isolation, envelope correlation coefficient and diversity gain.     

A dual‐band dual‐polarized cubical DRA coupled with new modified cross‐shaped slot for ISM (2.4 GHz) and Wi‐MAX (3.3‐3.6 GHz) band applications

In this article, a new modified cross‐shaped coupled cubical dielectric resonator antenna (DRA) has been investigated for dual‐band dual‐polarized applications. The linearly polarized (LP) fields in DRA has been generated by using a single slot in the ground plane and kept at either 45° (S_L1) or ?45° (S_L2) from the microstrip feed line. Combining these two slots (S_L1 and S_L2) in the modified ground plane, the proposed structure able to generate circularly polarized (CP) field in DRA. But the generated CP field is not enough to cover ISM 2400 band. To achieve CP in ISM 2400 band, an extra slot (S_L3) to the existing slots and an extra strip (S_T) in the circular ring feed line have been included. This modified final antenna arrangement has been able to produce LP (due to loading effect, ie, slot and DRA) and CP fields (orthogonal modes have been generated, ie, TE ^x₁₁₁ and TE ^y₁₁₁), simultaneously. The measured CP and LP, ?10 dB impedance bandwidths are 11.85% (2.38‐2.68 GHz) and 9.11% (3.25‐3.56 GHz) in combination with the 3‐dB axial ratio bandwidth of 4.11% (2.38‐2.48 GHz). The generated CP and LP fields are used for different wireless communication bands such as ISM 2400 and Wi‐MAX (3.3‐3.7 GHz) bands.     

A vertex‐fed hexa‐band frequency reconfigurable antenna for wireless applications

Present article embodies the design and analysis of an octagonal shaped split ring resonator based multiband antenna fed at vertex for wireless applications with frequency‐band reconfigurable characteristics. The proposed antenna is printed on FR4 substrate with electrical dimension of 0.4884 λ × 0.4329 λ × 0.0178 λ (44 × 39 × 1.6 mm³), at lower frequency of 3.33 GHz. The antenna consists of SRR based vertex fed octagonal ring as the radiation element and switchable reclined L‐shaped slotted ground plane. Antenna achieves six bands for wireless standards viz: upper WLAN (5.0/5.8 GHz), lower WiMAX (3.3 GHz), super extended C‐band (6.6 GHz), middle X band (9.9 GHz—for space communication), and lower K_U band (15.9 GHz—for satellite communication systems operating band). Stable radiation patterns are observed for the operating bands with low cross polarization. The proposed design achieves hexa band characteristics during switching ON state of PIN diode located at reclined L‐shaped slot in the ground plane. Experimental characteristic of antenna shows close agreement with those obtained by simulation of the proposed antenna.     

A penta‐band hybrid fractal MIMO antenna for ISM applications

A miniature two‐element MIMO multiband planar patch antenna with potential applications in the ISM bands is presented. The elements of the antenna have been designed using a novel hybrid fractal geometry based on an altered Dragon Curve and the Inverted Koch. Reduced antenna dimensions are obtained with acceptable performance even at lower frequency ranges. The antenna elements are placed adjacent to each other with a very small spacing of 0.004 λ₀ (λ being the free space wavelength of 433 MHz), confining the antenna dimensions to 51 × 50 mm². The antenna resonates at the 433 MHz (ISM), 2.4 GHz (ISM), 3.9 GHZ (Fixed Satellite), 4.7 GHz (UWB) and 5.8 GHz (ISM) frequency bands. The antenna exhibits |S₁₁| ≤ ?10 dB, |S₂₁| ≤ ?16 dB, an ECC ≤ 0.01 for all operating frequencies, with circular polarisation at the 2.4 GHz and 5.8 GHz bands and linear polarisation at the others. The simulated structure was fabricated and tested, with the simulated and measured results displaying acceptable agreement.     

Uniplanar ACS fed multiband high‐gain antenna with extended rectangular strips for portable system applications

In this article, a compact uniplanar asymmetric coplanar strip (ACS)‐fed multiband antenna with extended rectangular strips is proposed for portable system applications. It is composed of a modified mouse and rectangular‐shaped radiating strip for generating three resonance frequency bands simultaneously. The proposed antenna has a compact size of 16 × 26 × 1.6 mm³. Antenna has |S₁₁| ≤ ?10 dB at three independent controlled bandwidths from 2.2 to 2.4 GHz, 3.5 to 3.7 GHz, and 4.85 to 6.85 GHz. The proposed ACS‐fed antenna is suitable for LTE 2300, WiBro 2300 GHz, 5.2/5.8‐GHz WLAN, 3.5/5.5‐GHz WiMAX, 4.9‐GHz US public safety band, and 5.9‐GHz WAVE applications. The antenna has omnidirectional radiation characteristics in the desired frequency bands in both E‐plane and H‐plane. It has better gain value performance compared with other antenna designs discussed in the literature.     

Dual band frequency tunable planar inverted‐F antenna for mobile handheld devices

A single feed, dual‐band frequency tunable planar inverted‐F antenna (PIFA) is presented for mobile handheld device applications. The proposed antenna is designed using the transmission line model. The dual‐band frequency tunability is achieved by varying the capacitance of the varactor diode between 4.15 pF (0 V) and 0.72 pF (15 V). The measured impedance bandwidth of ?6 dB is realized from 0.8 to 0.98 GHz for the lower band and 1.65 to 2.2 GHz for the higher band. The designed antenna provides the independent frequency tunability for both the bands without disturbing each other. The maximum antenna gain is estimated 2.64 dBi for the proposed PIFA. Also, it has a maximum efficiency of ~85% for the mobile handheld device. In addition, the proposed PIFA is investigated with SAM phantom model for head and hand, found to be within the acceptable SAR limit of 1.6 W/Kg.     

Miniaturized dual‐band metamaterial inspired antenna with modified SRR loading

A miniaturized dual‐band CPW‐fed Metamaterial antenna with modified split ring resonator (SRR) loading has been presented in this paper. Proposed antenna comprises a tapered rectangular patch with a slot in which an elliptically SRR has been loaded to achieve miniaturization. Proposed antenna shows dual band operations in the operating band 3.25‐3.42 and 3.83‐6.63 GHz, respectively. It has been observed that lower mode (at 3.36 GHz) is originated by means of modified SRR. SRR is being modified by small meandered line inductor which is placed instead of strip. This provides an extra inductance to SRR resulting miniaturization. Overall electrical size of the proposed antenna is 0.222 × 0.277 × 0.017 λ₀ at 3.36 GHz. Second band is due to coupling between feed and ground planes. The antenna offers an average peak gain of 1.72 and 3.41 dB throughout the first and second band respectively. In addition to that this antenna exhibits perfect omnidirectional and dipolar radiation patterns at xz‐ and yz‐ plane respectively. Due to consistent radiation pattern, ease of fabrication, and compact nature this antenna can be used for wireless applications such as worldwide interoperability for microwave access (WiMAX), industrial, scientific and medical (ISM) band, WLAN/Wi‐Fi bands.     

Compact dual wide‐band four/eight elements MIMO antenna for WLAN applications

A compact four and eight elements multiple‐input‐multiple‐output (MIMO) antenna designed for WLAN applications is presented in this article. The antenna operates in IEEE 802.11b/g WLAN (2.4 GHz), IEEE 802.11 ac/n WLAN (5.2 and 5.8 GHz) and WiMAX (5.8 GHz) bands. The resonated mode of the antenna is achieved by two unequal Reverse‐L shaped, line‐shaped slots on top and parasitic element on the ground layer. The single antenna provides wide bandwidth of about 29% (2.3‐3.1 GHz) in lower and 22% (4.9‐6.1 GHz) in the upper band. The compactness of the single element antenna is found about 95% with respect to the patch and 61% in overall dimension. Thereafter an investigation is carried out to design two, four, and eight elements MIMO antennas. All of the multi‐element structures provide compact configuration and cover entire WLAN frequency ranges (2.4‐2.48 and 5.15‐5.85 GHz). The dimension of the proposed eight element MIMO antenna is 102 × 52 × 1.6 mm³. It covers the frequency (measured) from 2.4 to 3.1 GHz and 5 to 6.1 GHz. The diversity performance of the proposed MIMO antenna is also assessed in terms of the envelope correlation coefficient (ECC), diversity gain (DG), and total active reflection co‐efficient (TARC). The ECC is found <0.5 whereas the DG >9.0 is obtained for the desired bands.     

Coplanar waveguide‐fed electrically small dual‐polarized short‐ended zeroth‐order resonating antenna using Ω‐shaped capacitor and single‐split ring resonator for GPS/WiMAX/WLAN/C‐band applications

This work explains the design and analysis of a triple‐band electrically small (ka = 0.56 < 1) zeroth‐order resonating (ZOR) antenna with wideband circular polarization (CP) characteristics. The antenna compactness is obtained due to ZOR frequency of composite right/left‐handed (CRLH) transmission line (TL) and wideband CP radiation are achieved due to the introduction of single‐split ring resonator and asymmetric coplanar waveguide fed ground plane. The proposed antenna obtains an overall electrical size including the ground plane of 0.124 λ₀ × 0.131 λ₀ × 0.005 λ₀ at 1.58 GHz and physical dimension of 23.7 × 25 × 1 mm³ are achieved. The antenna provides a size reduction of 44.95% compared to a conventional monopole antenna. The novelty behind the ohm‐shaped capacitor is the generation of extra miniaturization with better antenna compactness. The antenna provides dual‐polarized radiation pattern with linear polarization radiation at 1.58 and 3.54 GHz, wideband CP radiation at 5.8 GHz. The antenna measured results shows good impedance bandwidth of 5%, 6.21%, and 57.5% for the three bands centered at 1.58, 3.54, and 5.8 GHz with a wider axial ratio bandwidth (ARBW) of 25.47% is obtained in the third band. The antenna provides a higher level of compactness, wider ARBW, good radiation efficiency, and wider S₁₁ bandwidth. Hence, the proposed antenna is suitable for use in GPS L1 band (1.565‐1.585 GHz), WiMAX 3.5 GHz (3.4‐3.8 GHz) GHz, WLAN 5.2/5.8 GHz (5.15‐5.825 GHz), and C‐band (4‐8 GHz) wireless application systems.     

A low volume flexible CPW‐fed elliptical‐ring with split‐triangular patch dual‐band antenna

In this article, the intensive investigations are carried out on a low volume compact flexible antenna for wireless applications with a novel structure model. The proposed model has considered as an elliptical‐ring with split‐triangular patch (ERSTP) antenna with the coplanar waveguide feeding to achieve dual‐bands. The ERSTP antenna is designed with polyimide material having the volume (L _a × W _a × h) 99 mm³. The ERSTP antenna resonates with 2.60 GHz and 3.48 GHz frequencies with a reflection coefficient of ?21.92 dB and ?32.14 dB and a gain of 2.39 dBi and 1.75, dBi respectively. The impedance bandwidths are 100 MHz and 330 MHz observed at two frequency bands. The proposed ERSTP antenna has operated on mobile‐worldwide interoperability for microwave access (M‐WiMAX) and worldwide interoperability for microwave access (WiMAX) bands respectively. The simulated and measured results of ERSTP antenna are in good agreement.     

Semi fractal three leaf clover‐shaped CPW antenna for triple band operation

This article presents a unique and compact coplanar waveguide (CPW) antenna that exhibits triband operation with circular polarization. The single antenna was designed to operate simultaneously in the following bands: WiMAX (3.3–3.6 GHz), wireless local area network (WLAN) (5.15–5.825 GHz), ITS (5.795–6.400 GHz), and ITU‐R (7.725–8.5 GHz). The realization of the triband antenna was achieved by using two semi fractal ring patches resembling the shape of a three leaf clover, and by introducing a pair of symmetrical L‐shaped slits in its ground plane. The antenna's physical parameters were investigated to fully understand their affect on the antenna's performance. The salient parameters obtained from this analysis enabled the optimization of the antenna's overall characteristics. The design concept was confirmed by fabricating the antenna prototype and measuring its characteristics. The proposed antenna has dimensions of 20 × 20 × 1 mm³. Measured results show the antenna exhibits circular polarization in WiMAX and ITU‐R bands, and linear polarization in the WLAN band. The antenna radiates omnidirectionally in the H‐plane, and approximately bidirectionally in the E‐plane. In addition, the antenna presents stable gain over the triband. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:413–418, 2015.     

Compact dual‐band printed quadrifilar helix antenna for practical hand‐held devices

This paper proposes a compact dual‐band printed quadrifilar helix antenna (QHA) operating at GPS‐L1 (1575 ± 2 MHz) and L2 (1228 ± 2 MHz) bands. To generate the dual operating bands, two interconnected lines with unequal lengths are introduced as a radiating element. The closely allocated radiators resonate in quarter‐wavelength mode, which significantly miniaturizes antenna's size. Four shunt capacitors are loaded near ports to manipulate the mutual coupling between each two radiators, so that satisfactory matching condition with minimum active reflection at two target bands can be obtained simultaneously. Then, a compact feeding network consisting of on‐chip hybrid couplers is designed and connected to the QHA. Measured results show that the compact proposed antenna achieves peak gains of 1.5 dBic and 2.6 dBic at 1575 MHz and 1228 MHz, respectively. The axial ratios (ARs) at L1 and L2 bands are both below 2.5 dB, and the half‐power‐beamwidths (HPBWs) are as wide as 130° and 116°, respectively. As compared with reported works, the proposed antenna can achieve much more compact size (0.11 × 0.21 λ₀²) and dual‐band radiation at the same time.     

A miniaturized circularly polarized implantable RFID antenna for biomedical applications

A miniaturized circularly polarized implantable antenna operating at ultrahigh frequency band (902‐928 MHz) for radio frequency identification biomedical monitoring is first presented and experimentally validated in this article. The proposed antenna features a compact volume with a dimension of π × (6)² × 1.27 mm³ by employing an extended ring with meandered lines for size reduction. Moreover, adjusting the length of symmetrical meandered lines can introduce two orthogonal modes, which makes for good performance of circular polarization. Superb impedance matching between the chip and tag antenna is well implemented by applying a modified T‐match stub. In the simulation, the antenna achieves a ?10‐dB impedance bandwidth of 42 MHz (902‐944 MHz) and 3‐dB axial‐ratio bandwidth is 53 MHz (892‐945 MHz). Finally, the specific absorption rate is also calculated for human safety and the measured reading range reaches the maximum distance of about 87 cm.