Dielectric resonator based two‐port dual band antenna for MIMO applications

This article investigates a dual band multiple input multiple output (MIMO) cylindrical dielectric resonator antenna (cDRA) for WLAN and WiMAX applications. It consists of two symmetrical orthogonally placed radiators. Each radiator is excited through a narrow rectangular aperture with the help of a microstrip line. For higher mode excitation, the proposed structure uses dual segment DRA which apparently looks like stacked geometry. The aperture fed dielectric resonator works as a feed for upper cDRA to generate higher order mode. The presented radiator covers the band between 3.3‐3.8 GHz and 5‐5.7 GHz. The measured isolation is better than 20 dB in the desired band. The average gain and radiation efficiency achieved for the proposed antenna is 6.0 dBi and 85%, respectively at the operating frequency band. In the proposed geometry, broadside radiation patterns are achieved by exciting HEM_11δ and HEM_12δ modes in a stacked geometry. Different MIMO performance parameters (ECC, DG, MEG, and CCL) are also estimated and analyzed. The prototype of proposed antenna is fabricated and tested. The measured outcomes are in good accord with the simulated one.     

Dual‐port MIMO dielectric resonator antenna for WLAN applications

A dual‐port multiple‐input multiple‐output (MIMO) dielectric resonator antenna (DRA) for 5 GHz IEEE (802.11a/h/j/n/ac/ax) is discussed in this article. Two prototypes of single feed DRA and dual feed MIMO DRA are fabricated and measured results are compared with the simulated data. The proposed single feed DRA and dual feed MIMO DRA exhibits wide impedance bandwidth (IBW). Antennas have been fabricated on Rogers RT Duroid substrate with Eccostock made DRA placed over the substrate. DRAs are excited by aperture coupled feed to achieve wide bandwidth and high efficiency. The measured IBW of uniport DRA and dual‐port MIMO DRA are 26.6% (4.75‐6.21 GHz) and 27.5% (4.7‐6.2 GHz) respectively. Maximum gain of the antenna is 7.4 dBi. The results of the antennas are in good agreement with simulated data and they are suitable for WLAN applications. These antennas are also compact with area of substrate 32.8 cm².     

Compact meander T‐shaped monopole antenna for dual‐band WLAN applications

A compact coplanar waveguide‐feed monopole antenna with dual‐band characteristics is proposed in this article. The proposed antenna mainly consists of meander T‐shaped monopole and small ground plane embedded with a pair of L‐shaped couple slots and two pairs of I‐shaped notched slots symmetrically. By elongating the meander T‐shaped arms and carefully selecting the positions and lengths of L‐shaped slot and I‐shaped slot, the antenna excites four resonant frequencies at 2.42, 2.52, 4.75, and 5.54 GHz which are formed into two wide bands to cover all the 2.4/5.2/5.8 GHz wireless local area network (WLAN) operating bands, and is with miniaturization structure. Moreover, the antenna can provide nearly dipole‐like radiation patterns and good gains across the dual operating bands. These results prove that the proposed dual‐band antenna is very suitable for WLAN applications. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Broadband circularly polarized printed falcate‐shaped monopole antenna

In this study, a simple broadband circularly polarized (CP) printed monopole antenna for S/C‐band applications is proposed. The CP antenna is composed of a falcate‐shaped monopole with a right‐angle trapezoid stub, then wide impedance and axial ratio (AR) bandwidths are achieved. By placing one rectangular split‐ring resonator above the stub for generating upper CP mode, both of impedance and CP performances are further improved. The proposed antenna is fabricated on a FR4 substrate and measured. The measured ?10‐dB impedance bandwidth is 107%, ranging from 2.4‐7.9 GHz, and the measured 3‐dB AR bandwidth is 94% (2.4‐6.6 GHz), covering the entire wireless local area network (WLAN) and WiMAX bands.     

Compact C‐shaped MIMO diversity antenna for quad band applications with hexagonal stub for isolation improvement

A compact MIMO antenna was proposed in this article. The designed antenna is compact in size with dimensions of 20 × 34 × 1.6 mm. In this proposed antenna model the patch consisting of two counter facing C‐shaped elements facing each other in which a hexagonal ring attached to a strip line which is placed in between the two C‐shaped patch acts as the stub. The novelty of the antenna elements lies isolation improvement by using the ground stub with the use of circular ring resonator. The proposed antenna operates in four bands in which 2.66 to 3.60 GHz (Wi‐Max, Wi‐Fi), 4.52 to 5.78 GHz (WLAN), 6.59 to 7.40 GHz (satellite communication), and 9.55 to 10.91 GHz and having bandwidth of 0.94, 1.26, 0.81, and 1.36 GHz at four bands. The envelope correlation coefficient is ECC ≤ 0.3 and diversity gain > 9.8 dB for the operating bands of antenna proposed. This antenna can work in the bands of Wi‐Max, Wi‐Fi, WLAN, satellite communication in X‐band and for radio location, and astronomy applications.     

A metamaterial hepta‐band antenna for wireless applications with specific absorption rate reduction

Present article embodies the design and analysis of slotted circular shape metamaterial loaded multiband antenna for wireless applications with declination of SAR. The electrical dimension is 0.260 λ × 0.253 λ × 0.0059 λ (35 × 34 × 0.8 mm³) of proposed design, at lower frequency of 2.23 GHz. The antenna consists of circular shape rectangular slot as the radiation element loaded with metamaterial split ring resonator (SRR) and two parallel rectangular stubs, etched rectangular single complementary split‐ring resonator (CSRR) and reclined T‐shaped slot as ground plane. Antenna achieves hepta bands for wireless standards WLAN (2.4/5.0/5.8 GHz), WiMAX (3.5 GHz), radio frequency identification (RFID) services (3.0 GHz), Upper X band (11.8 GHz—for space communication) and Lower K_U band (13.1 GHz—for satellite communication systems operating band). Stable radiation patterns are observed for the operating bands with low cross polarization. The SRR is responsible for creating an additional resonating mode for wireless application as well as provide the declination in SAR about 13.3%. Experimental characteristic of antenna shows close agreement with those obtained by simulation of the proposed antenna.     

Complementary meander‐line‐inspired dielectric resonator multiple‐input‐multiple‐output antenna for dual‐band applications

The communication presents a simple dielectric resonator (DR) multiple‐input‐multiple‐output (MIMO) dual‐band antenna. It utilizes two “I”‐shaped DR elements to construct an “I”‐shaped DR array antenna (IDRAA) for MIMO applications. The ground plane of the antenna is defected by two spiral complementary meander lines and two circular ground slots. In the configuration, two “I”‐shaped DR elements are placed with a separation of 0.098λ. The antenna covers dual‐band frequency spectra from 3.46 to 5.37 GHz (43.26%) and from 5.89 to 6.49 GHz (9.7%). It ensures the C‐band downlink (3.7‐4.2 GHz), uplink (5.925‐6.425 GHz), and WiMAX (5.15‐5.35 GHz) frequency bands. Each DR element is excited with a 50‐Ω microstrip line feed with aperture‐coupling mechanism. The antenna offers very high port isolation of around 18.5 and 20 dB in the lower band and upper band, respectively. The proposed structure is suitable to operate in the MIMO system because of its very nominal envelope correlation coefficient (<0.015) and high diversity gain (>9.8). The MIMO antenna provides very good mean effective gain value (±0.35 dB) and low channel capacity loss (<0.35 bit/s/Hz) throughout the entire operating bands. Simulated and measured results are in good agreement and they approve the suitability of the proposed IDRAA for C‐band uplink and downlink applications and WiMAX band applications.     

A novel compact self‐similar fractal UWB MIMO antenna

A novel compact self‐similar fractal ultra‐wideband (UWB) multiple‐input‐multiple‐output (MIMO) antenna is presented. This fractal geometry is designed by using iterated function system (IFS). Self‐similar fractal geometry is used here to achieve miniaturization and wideband performance. The self‐similarity dimension of proposed fractal geometry is 1.79, which is a fractional dimension. The antenna consists of two novel self‐similar fractal monopole‐antenna elements and their metallic area is minimized by 29.68% at second iteration. A ground stub of T‐shape with vertical slot enhances isolation and impedance bandwidth of proposed MIMO antenna. This antenna has a compact dimension of 24 × 32 mm² and impedance bandwidth (S₁₁ < ?10 dB) of 9.4 GHz ranging from 3.1 to 12.5 GHz with an isolation better than 16 dB. The various diversity performance parameters are also determined. There is good agreement between measured and simulated results, which confirms that the proposed antenna is acceptable for UWB applications.     

Compact wideband bandpass filter based on double‐T‐shaped stub loaded resonator and loading technique for zero‐voltage point

In this article, a double‐T‐shaped stub centrally loaded uniform impedance resonator (UIR) is introduced and its resonant characteristics are well clarified, which provided a simple approach for triple‐mode wideband bandpass filter (BPF) design. The double‐T‐shaped stub consists of a T‐shaped stub at the center of UIR and two shunt uniform‐impedance stubs at the T‐shaped stub. Furthermore, loading technique for zero‐voltage point is employed to guide design procedure from UIR to the proposed resonator. The resonant frequencies of the first three modes for the resonator can be free to adjust by the length of the UIR and the two kinds of stub. Finally, a compact wideband BPF is designed, fabricated, and measured. The measured results are in good agreement with the full‐wave simulation results. The realized wideband filter exhibits a 3 dB fractional bandwidth of 69.1% with good in‐band filtering performance, wide stopband, and sharp out‐of‐band rejection skirt.     

An ultra wideband “OM” shaped DRA with a defected ground structure and dual polarization properties for 4G/5G wireless communications

This research article reports a new Dielectric Resonator Antenna (DRA) with its Dielectric resonator (DR) modified to an “OM” shape for UWB (3.1‐11.1 GHz), to support high data rate multimedia applications for 4G/5G communications. The proposed DRA reports a peak gain of 7.68 dB and a dual polarization behavior for a frequency band from 6 to 11.1 GHz. It has overall antenna dimensions of 50 × 40 × 4.87 mm³ and is fabricated on a commercially available Rogers RT 5880 substrate (with ε_r = 2.2), which is fed using a microstrip feedline with a P‐type transformer that offers an input impedance of 50 Ω to the DR. A conformal strip between the feedline and the OM shaped DR improves the impedance matching at the UWB frequency response of the DRA. This UWB frequency response is mainly because of its optimized “OM” shaped DR structure that excites a TE₁₁₁ mode at 4.9 GHz and two higher order modes TE₂₁₁ and TE₂₂₁ at resonant frequencies of 7.2 and 8.35 GHz, respectively. Additionally the proposed OM shaped DR also generates orthogonal modes of TE₂₁₁^x and TE₂₁₁^y at 6.5 and 7.2 GHz and TE₂₂₁^x and TE₂₂₁^y at 8.35 and 10 GHz, respectively. The proposed DRA therefore exhibits an elliptically polarized behavior with axial ratio bandwidth of 5.1 GHz (≤10 dB) from 6 to 11.1 GHz. A measured impedance bandwidth of 5.25 GHz from 3.8 to 9.05 GHz and 1.5 GHz from 10 to 11.5 GHz and a peak‐measured gain of 7.68 dB at 10.5 GHz (with an average gain of 4.6 dB) has been reported for the proposed DRA. An UWB performance, with good gain properties and an elliptically polarized behavior allows the proposed “OM” shaped DRA to be suitable for short range 4G/5G UWB wireless communications for future multimedia rich WPAN (wireless personal area networks), WLAN, Wi‐MAX, INSAT applications, satellite applications, and X band RADAR (for defense communication) applications.     

A wideband reflectarray antenna using single‐layer dipole element attached with T‐shaped stubs

A wideband reflectarray antenna consisting of single‐layer dipole element attached with T‐shaped stubs is proposed. By varying the lengths of the T‐shaped stubs, the unit cell can provide a linear phase curve covering about 420°. Critical design parameters are analyzed to understand its wideband operating mechanism. Using this novel type of unit cells, a 441 element 25° offset‐fed reflectarray with grid spacing of λ/3 at 10 GHz is designed, fabricated, and measured. The experimental results show that the proposed reflectarray can achieve 1‐dB gain bandwidth of 24% and 1.5‐dB gain bandwidth of 37%. In addition, aperture efficiency of 66.6% and cross polarization level of 29 dB are obtained at 10 GHz, respectively.     

Dual‐band circularly polarized MIMO DRA for sub‐6 GHz applications

In this article, a dual‐band circularly polarized multiple‐input‐multiple‐output (MIMO) dielectric resonator antenna (DRA) is proposed for 3.5 and 5.5 GHz bands, both being located under 6 GHz. Known as sub‐6 (or as mid‐band), they provide good coverage and capacity in the newly targeted fifth‐generation (5G) systems. The proposed structure consists of two ring DRAs (RDRAs) etched on a 0.8 mm thick RT Duroid substrate. Measured impedance bandwidths in broadside direction are 3.1‐3.75 GHz (19%) and 5.3‐5.6 GHz (9.4%) and circular polarization (CP) bandwidths are 3.425‐3.6 GHz (5%) and 5.45‐5.55 GHz (2%), respectively. CP is achieved by exciting HE modes using two probes placed orthogonaly to each other, that is, at an azimuthal angular distance of 90^° . Varying the lengths of the probe allows achieving the necessary time‐phase quadrature between modes. Comparison between recent multiband circularly polarized MIMO DRAs and proposed prototype has revealed that CP bandwidth in both bands is one of the highlighting advantages of the present configuration.     

Millimeter‐wave antenna with wide‐scan angle radiation characteristics for MIMO applications

A three‐element quasi Yagi‐Uda antenna array with printed metamaterial surface generated from the array of uniplanar capacitively loaded loop (CLL) unit‐cells printed on the substrate operating in the band 25‐30 GHz is proposed. The metamaterial surface is configured to provide a high‐refractive index to tilt the electromagnetic (EM) beam from the two dipole antennas placed opposite to each other. The metamaterial region focuses the rays from the dipole antenna and hence increases the gain of the individual antennas by about 5 dBi. The antenna elements are printed on a 10 mil substrate with a center to center separation of about 0.5 λ ₀ at 28 GHz. The three‐element antenna covers 25‐30 GHz band with measured return loss of 10 dB and isolation greater than 15 dB between all the three ports. The measured gain of about 11 dBi is achieved for all the antenna elements. The three antenna elements radiate in three different directions and cover a radiation scan angle of 64°.     

Dual port aperture coupled MIMO cylindrical dielectric resonator antenna with high isolation for WiMAX application

In this article, a dual port aperture coupled MIMO cylindrical dielectric resonator antenna with enhanced isolation is proposed. Dual feeding techniques are used to excite dielectric resonator. These feeding structures are oriented in such a way so that they can produce orthogonal mode in the dielectric resonator. High isolation is observed by generating two orthogonal modes, that is, and in the dielectric resonator. The fractional bandwidth for port 1 and port 2 is 17.8% (3.1‐3.68 GHz) and 18.4% (3.1‐3.7 GHz), respectively, and isolation between the two ports exceeds ?25 dB within the required band. The proposed antenna is simulated, fabricated, and experimentally tested. Good agreements between measured and simulated results are observed. The various diversity performance parameters are also lie within their acceptable limits. Based on presented results, it can be concluded that the presented MIMO antenna is suitable for WiMAX (3.3‐3.6 GHz) applications.     

Novel analysis of the size and orientation dependent resonance phenomenon of the microstrip line coupled complementary split‐ring resonator

The purpose of this article is to provide a comprehensive investigation on the resonance phenomenon of microstrip line coupled complementary split‐ring resonator (CSRR) with different orientation and relative size. It is shown that when the relative size of the CSRR is smaller than the host line, the CSRR with its slit oriented orthogonal to the line axis will not excite effectively and show weak resonance behavior. However, when the slit is positioned along the line axis, the cross‐polarization effect comes into play, which excites the CSRR through the mixed coupling. To ensure the correctness, several numerical simulations are carried out for different substrate height and relative permittivity. Finally, a prototype is fabricated and measured for the experimental validation.     

CPW fed miniaturized dual‐band short‐ended metamaterial antenna using modified split‐ring resonator for wireless application

A miniaturized dual‐band metamaterial (MTM) antenna has been designed in this article. The designed coplanar waveguide fed antenna has composed of inner split‐ring resonator and an outer open ring resonator with rectangular stub. The series parameter of the antenna is used to determine the zeroth order resonance frequency due to short‐ended boundary condition. The whole size of proposed structure is 20 × 25.5 mm². This MTM antenna exhibits dual‐band operation at 3.17 GHz (3.1–3.22 GHz) and 5.39 GHz (5.27–5.47 GHz). The proposed MTM structure achieves measured peak gain of 0.71 and 1.89 dB at 3.17 and 5.39 GHz, respectively. The proposed antenna can be used for recent radio communication in form of S‐band application and Wi‐MAX.     

Compact four‐element MIMO SIW cavity backed slot antenna with high front‐to‐back ratio

In this article, a novel design of single layer, compact, multiple input multiple output (MIMO) half‐mode substrate integrated waveguide (HMSIW) cavity backed quad element slot antenna with high front‐to‐back ratio (FTBR) is proposed. The proposed antenna consists of four rectangular SIW cavities with semi‐taper radiating slots. The antenna elements are placed in a fashion to achieve high isolation. This antenna is designed for WLAN vehicular communication system to cover the frequency range of 5.84 GHz to 5.96 GHz. It has high front to back ratio (FTBR) of more than 25 dB without using any external metallic reflector. It has more than 37 dB isolation in between orthogonal elements and more than 24 dB in between parallel elements. The envelop correlation coefficient (ECC) and diversity gain are 0.003 and 9.99 dB respectively in between all the elements. Moreover, the antenna has high gain and efficiency of more than 8 dB and 94%, respectively, in 10 dB impedance bandwidth. It can be tuned in a wide range of frequency.     

A Multiband antenna using plus‐shaped fractal‐like elements and stepped ground plane

A multiband planar symmetrical plus‐shaped fractal monopole antenna with stepped ground plane is presented in this study. Measured results show that the proposed antenna operates with 10 dB return loss bandwidths from 1.630 to 1.88 GHz and from 4.5 to 8.5 GHz covering The Global System for Mobile Communications (GSM) 1800 MHz 2G spectrum band, 4400 to 4900 MHz 5G spectrum band adopted by Japan and China for future 5G communication in sub‐6 GHz band, 5.15 to 5.925 GHz LTE band 46, WLAN IEEE 802.11 y/a/h/j/n/P bands, and 5.8 to 7.707 GHz military band. The antenna gain varies between 1.73 and 1.97 dB in lower band and 3.6 to 5.05 dBi in upper band with radiation efficiencies more than 90% in lower band and more than 80% in upper band. The antenna has more than 64 and 28 dB isolations between the copolar and cross‐polar radiation patterns in the lower and upper bands, respectively.     

A novel wideband bandpass filter based on CSRR‐loaded substrate integrated folded waveguide

A novel wideband bandpass filter based on folded substrate integrated waveguide (FSIW) is presented in the article. Five square complementary split‐ring resonators (CSRRs) are etched in the middle layer of the FSIW. By adjusting the physical size of the CSRR structure, the resonant frequency of the CSRRs can be tuned at the same time and the stopband performance can be changed. As transverse electromagnetic (TEM) mode can be transmitted in the stripline, FSIW excited by stripline shows wider passband than that excited by microstrip line directly. To achieve perfect impedance matching, two microstrip lines to stripline transitions are added in two ports of the filter. The proposed bandpass filter exhibits compact size, high selectivity, good stopband rejection, lower radiation loss, and wideband performances. The measured results show that the fractional bandwidth of the filter is about 35.5%. The measured return loss is better than 15 dB from 4.84 GHz to 6.90 GHz, and the insertion loss is less than 1.2 dB. The comparison between the simulated results and the measured ones validate the possibility of the technology that combines the FSIW and CSRR.     

High isolation two‐port compact MIMO fractal antenna with Wi‐Max and X‐band suppression characteristics

This article features about an ultra‐wideband (UWB)‐multiple‐input multiple‐output (MIMO) antenna that exhibits the potentials of good port isolation and dual‐band suppression. The proposed antenna model consists of a unique fractal‐shaped radiating patch, a common ground interface leading to the incorporation of an intuitive approach; parasitic inverted neutralization stubs, which is located at the central co‐ordinate axis system, protruded vertically, where its extension is twisted with a motive of enhancing the port isolation. In addition to that, contiguous notches are implemented to achieve band‐notching at WiMAX (3.35‐4.45 GHz) and X‐band (9‐10 GHz). The total electrical area of UWB MIMO antenna is 0.179(λ₀)² at 2.25 GHz. To rationalize the counterparts of MIMO and band‐notching, diversity performance is studied through the electromagnetic (EM) solver and the corresponding circuit analysis is pursued through a electronic design automation (EDA) solver. The prototype has been fabricated, measured, and agreed well with the simulated results. The feasibility of proposed antenna model is considered to be quite optimum, with due consideration of its outcomes from applications point‐of‐view.