Birefringent light‐shaping films for mini‐LED backlights

Birefringent light‐shaping films (BLSFs) for mini‐LED backlit liquid crystal displays (LCDs) are proposed and experimentally demonstrated by passive polymer‐dispersed liquid crystal (PDLC) films. Such films show angle‐selective scattering properties, achieved by proper material engineering and good vertical alignment of liquid crystals. They only respond to angles rather than spatial locations. By directly adhering the BLSF onto a LED, the angular intensity distribution of light can be tailored from Lambertian‐like to batwing‐like. Further simulation proves that by engineering the angular distribution, a fewer number of LEDs or equivalently a shorter light‐spreading distance is required to maintain good uniformity. These BLSFs are expected to find widespread applications in emerging mini‐LED backlit LCDs and shed light on designing other light‐shaping films in the future.     

High performance color‐converted micro‐LED displays

A full‐color micro‐LED display can be achieved by red, green, and blue (RGB) chips or by a blue/ultraviolet (UV) micro‐LED array to pump downconverters. The latter helps relieve the burden of epitaxial growth of tri‐color micro‐LED chips. However, such a color‐converted micro‐LED system usually suffers from color crosstalk and low efficiency due to limited optical density of color converters. With funnel‐tube array and reflective coating on its inner surface, the crosstalk is eliminated, and the optical efficiency can be improved by more than two times. In addition, the ambient contrast ratio is also improved because of higher light intensity. The color gamut of this device is approximately 92% of DCI‐P3 standard.     

Active matrix monolithic micro‐LED full‐color micro‐display

An active matrix monolithic micro‐LED full‐color micro‐display with a pixel density of 317 ppi is demonstrated. Starting from large‐scale and low‐cost GaN‐on‐Si epilayers, monolithic 64 × 36 blue micro‐LED arrays are fabricated and further transformed to full‐color micro‐displays by applying a photo‐patternable color conversion layer. This full‐color fabrication scheme shows feasible manufacturability, suggesting a potential for volume production of micro‐LED full‐color micro‐display.     

Inorganic light‐emitting diode displays using micro‐transfer printing

Large quantities of microscopic red, green, and blue light‐emitting diodes (LEDs) made of crystalline inorganic semiconductor materials micro‐transfer printed in large quantities onto rigid or flexible substrates form monochrome and color displays having a wide range of sizes and interesting properties. Transfer‐printed micro‐LED displays promise excellent environmental robustness, brightness, spatial resolution, and efficiency. Passive‐matrix and active‐matrix inorganic LED displays were constructed, operated, and their attributes measured. Tests demonstrate that inorganic micro‐LED displays have outstanding color, viewing angle, and transparency. Yield improvement techniques include redundancy, physical repair, and electronic correction. Micro‐transfer printing enables revolutionary manufacturing strategies in which microscale LEDs are first assembled into miniaturized micro‐system “light engines,” and then micro‐transfer printed and interconnected directly to metallized large‐format panels. This paper reviews micro‐transfer printing technology for micro‐LED displays.     

Fully‐integrated active matrix programmable UV and blue micro‐LED display system‐on‐panel (SoP)

High pixel per inch and high‐resolution micro‐LED displays are attracting more and more attentions. The increasing pixel number requires a large amount of bonding pads and brings huge difficulties to micro‐LED system design and lowers power efficiency as well. It is urgent to integrate row and column driving circuits onto the micro‐LED panel. Here, we report a fully integrated active matrix programmable micro‐LED system on panel (SoP) with ultraviolet and blue emission wavelengths. The micro‐LED SoP has a resolution of 60 × 60 and pixel pitch of 70 μm. The micro‐LED SoP was achieved by integrating micro‐LED arrays with silicon‐based p‐channel metal‐oxide semiconductor driving panel using fine‐toned flip‐chip bonding technology. With fully integrated scan and data circuits, the number of bonding pads was greatly reduced from 136 to 28, and large amount of metal interconnection lines were saved. The micro‐LED SoP panel was mounted on a periphery driving board, and representative characters were displayed successfully.     

High‐resolution and high‐brightness full‐colour “Silicon Display” for augmented and mixed reality

High‐brightness micro‐LED display bonded onto silicon backplane has been successfully demonstrated. The 0.38‐inch full‐colour active matrix LED microdisplay system consists of 352 × 198 pixels. Each pixel is 24 μm square composed of red, green, and blue (RGB) subpixels corresponding to a pixel resolution of 1053 ppi. Quantum‐dot materials are formed on III‐nitride blue micro‐LED array to convert blue light into red and green for full‐colour operation. We have confirmed that this microdisplay, which we call “Silicon Display” has wide colour gamut exceeding 120% of sRGB. We describe the advantage of this colour‐converting approach for the full‐colour micro‐LEDs. Progress toward higher resolution is also described. Brightness of more than 30 000 cd/m² has been confirmed at a driving current density of 4 A/cm² for 3000 ppi blue monochrome micro‐LED prepared for full‐colour Silicon Display. We believe our “Silicon Display” is ideally suited for near‐to‐eye displays for augmented and mixed reality.     

In‐pixel temperature sensor for high‐luminance active matrix micro‐light‐emitting diode display using low‐temperature polycrystalline silicon and oxide thin‐film‐transistors

We propose an in‐pixel temperature sensor using low‐temperature polycrystalline silicon and oxide (LTPO) thin‐film transistor (TFTs) for high‐luminance active matrix (AM) micro‐light‐emitting diode (LED) displays. By taking advantage of the different off‐current characteristics of p‐type LTPS TFTs and n‐type a‐IGZO TFTs under temperature change, we designed and fabricated a temperature sensor consists of only LTPO TFTs without additional sensing component or material. The fabricated sensor exhibits excellent temperature sensitivity of up to 71.8 mV/°C. In addition, a 64 × 64 temperature sensor array with 3T sensing pixel and integrated gate driver has also been fabricated, which demonstrates potential approach for maxing out the performance of high‐luminance AM micro‐LED display with real‐time in‐pixel temperature monitoring.     

LED packaging by ink‐jet microdeposition of high‐viscosity resin and phosphor dispersion

Abstract— An ink‐jet‐printing method applied to the microdeposition of high‐viscosity resin, including optimization of phosphor dispersion for light‐emitting‐diode (LED) packaging was examined for the first time. An ultrasonic ink‐jet‐printing method was used, in which ink droplets are ejected by a focused ultrasonic beam from a nozzle‐less printhead. To fabricate white LEDs, high‐viscosity phosphor‐dispersed resin was deposited to form an encapsulant dome. Two types of methods to control phosphor sedimentation for color uniformity were examined; one is heating the lead frame during the resin deposition, and the other is hydrophobic surface treatment of the lead frame base enabling the fabrication of a small encapsulant dome. For light direction control, a silicone micro lens was deposited on an encapsulant dome using the ink‐jet method. The results show that ultrasonic ink‐jet printing is an applicable technique to optimize and modify on‐demand optical characteristics of LED devices.     

How to reduce light leakage and clipping in local‐dimming liquid‐crystal displays

Abstract— In conventional LCDs, the backlight is set to maximum luminance regardless of the image. For dark scenes, this approach causes light leakage and power waste. Especially, light leakage in dark scenes degrades the contrast ratio of LCDs; to circumvent this problem, local‐dimming systems have been proposed. In these systems, the LED backlight is divided into several local blocks and the backlight luminance of each local block is controlled individually, and pixel values are adjusted simultaneously according to the luminance profile of the dimmed backlight. In this paper, a method of determining the LED backlight luminance of each local block depending on the image is proposed; this method significantly improves the image quality of LCDs. First, we introduce methods of quantifying light‐leakage at dark gray levels and clipping at bright gray levels. Then, the proposed method to determine the dimming duty, which controls the LED backlight luminance by compromising between these two measures, was derived. The proposed algorithm preserves the original image with little clipping distortion and effectively reduces light leakage.     

White‐LED backlight control for motion‐blur reduction and power minimization in large LCD TVs

Abstract— A 1‐D LED‐backlight‐scanning technique and a 2‐D local‐dimming technique for large LCD TVs are presented. These techniques not only reduce the motion‐blur artifacts by means of impulse representation of images in video, but also increase the static contrast ratio by means of local dimming in the image(s). Both techniques exploit a unique feature of an LED backlight in large LCD TVs in which the whole panel is divided into a pre‐defined number of regions such that the luminance in each region is independently controllable. The proposed techniques are implemented in a Xilinx FPGA and demonstrated on a Samsung 40‐in. LCD TV. Measurement results show that the proposed techniques significantly reduce the motion‐blur artifacts, enhance the static contrast ratio by about 3×, and reduce the power consumption by 10% on average.     

Energy‐efficient liquid‐crystal displays (e2‐LCDs) using a photonic‐crystal backlight system

Abstract— Cholesteric liquid crystals automatically form one‐dimensional photonic crystals. For a photonic crystal in which light‐emitting moieties are embedded, unique properties such as microcavity effects and simultaneous light emission and light reflection can be expected. Three primary‐color photonic‐crystal films were prepared based on cholesteric liquid crystal in which fluorescent dye is incorporated. Microcavity effects, i.e., emission enhancement and spectrum narrowing, were observed. Two types of demonstration liquid‐crystal displays (LCDs) were fabricated using the prepared photonic‐crystal films in a backlight system. One is an area‐color LCD in which a single photonic‐crystal layer is used for each color pixel and the other is a full‐color TFT‐LCD in which three stacked photonic‐crystal layers are used as light‐conversion layers. The area‐color LCD was excited by using 365‐nm UV light, and the full‐color TFT‐LCD was excited by using 470‐nm blue LED light. Because of the photonic crystal's unique features that allow it to work as light‐emitting and light‐reflecting layers simultaneously, both LCDs demonstrate clear readable images even under strong ambient light, such as direct‐sunlight conditions, under which conventional displays including LCDs and OLED displays cannot demonstrate clear images. In particular, an area‐color LCD, which eliminated color filters, gives clear images under bright ambient light conditions even without backlight illumination. This fact suggests that a backlight system using novel photonic‐crystal layers will be suitable for energy‐efficient LCDs (e²‐LCDs), especially for displays designed for outdoor usage.     

LED backlight system with double‐prism pattern

Abstract— A LED backlight system with a double‐prism pattern for use in mobile phones to achieve thin and high luminance LED backlight systems is proposed. The double‐prism pattern is formed on the light guide of the proposed LED backlight system and simultaneously exhibited two optical functions: shifting of the light from the direction of the guided light toward the radiated light and controlling the directivity of the radiated light. Therefore, using the double‐prism pattern eliminates two prism sheets and a diffusive sheet, which are indispensable optical elements to exhibit the optical function that controls the directivity of light in conventional LED backlight systems. Consequently, the thickness of the proposed LED backlight system is reduced to 0.75 mm compared to that of the conventional system. A luminance of 3115 nits and a full‐width half maximum of 35° for radiated light, which are comparable to conventional LED backlight systems, were obtained.     

High‐performance local‐dimming algorithm based on image characteristic and logarithmic function

With the emergence of high‐dynamic range (HDR) image and video, displaying an HDR image or video on a standard dynamic range displays with natural visual effect, clear details on local areas, and high‐contrast ratio has become an important issue. To achieve HDR, local‐dimming technique has been commonly practiced. In this paper, we investigate the problem of local dimming for LED‐backlight LC display to provide algorithm support for developing HDR displays. A novel local‐dimming algorithm is proposed to improve the contrast ratio, enhance the visual quality, and reduce the power consumption of the LCDs. The proposed algorithm mainly consists of two parts. The first part is a backlight luminance extraction method based on dynamic threshold and the maximum grayscale of an image block to improve the contrast ratio and reduce the power consumption. In the second one, a pixel compensation method based on logarithmic function is used to improve the visual quality and contrast ratio. At the same time, in order to better smooth the backlight diffusion at the edges of the backlight luminance signal to enhance the accuracy of the pixel compensation, we draw on the idea of BMA and improve it to establish the backlight diffusion model with different low‐pass‐filter templates for different types of blocks. Simulation and measured results show that the proposed algorithm outperforms the competing ones in contrast ratio, visual quality, and power‐saving ratio.     

Implementation of an LED backlight for avionics displays

Abstract— The replacement of conventional light sources used to backlight displays with LEDs is very attractive in avionics. Today's LED technology provides devices suitable to implement display backlight sources but specific requirements need to be satisfied for avionics displays. This paper covers the development of an innovative LED backlight dedicated to avionics displays, realized in a new box geometry in order to generate more than 10,000 cd/m² on a 6 × 5‐in. active area using less than 28 W of power.     

Wide gamut LCD using locally dimmable four‐primary‐color LED backlight

This paper proposes a wide gamut LCD using locally dimmable four‐primary‐color (4PC) LED backlight. Although the color gamut of LCDs has been improved in recent years, it is insufficient to reproduce all the colors in the real world. The objective of this paper is to propose a wide gamut LCD that reproduces all the colors in the real world while keeping the cost increases to a minimum. We evaluated the color gamut reproduced by LEDs of multiple primary colors and selected cyan as the optimal color to be added to the three primary colors to reproduce all the colors in the real world. Therefore, we designed an LED backlight consisting of an additional only‐cyan LED with three‐primary‐color LEDs and developed a prototype LCD with 4PC LED backlight. Furthermore, we developed a local dimming algorithm for the 4PC LED backlight. As a result, we confirmed that the prototype LCD with the 4PC LED backlight is able to cover almost all the colors in the real world and also able to display natural images with highly saturated colors by local dimming.     

Non‐polar‐oriented InGaN light‐emitting diodes for liquid‐crystal‐display backlighting

Abstract— This article addresses spontaneously polarized light emission from GaN‐based light‐emitting diodes (LEDs) fabricated on electrically non‐polar crystallographic orientations and application of spontaneously polarized emission for backlighting of liquid‐crystal displays (LCDs). The first half of the article describes polarized light emission from GaN‐based LEDs and its role in solid‐state lighting technology. The second half reports on our experimental work to explore the potential of non‐polar LEDs for LCD backlighting applications. Optical transmission of non‐polar LED emission was characterized through a liquid‐crystal layer. Extinction ratios of 0.21 were measured between zero and an applied bias voltage to the liquid‐crystal cells. These extinction ratios are not particularly high yet; nevertheless, the experiment has demonstrated the potential of such non‐polar LEDs for LCD backlighting.     

A reflective polarizer‐free display using dye‐doped polymer‐stabilized blue‐phase liquid crystals

Abstract— A reflective polarizer‐free display using dye‐doped polymer‐stabilized blue‐phase liquid crystal (DDPSBP‐LC) has been demonstrated. The mechanism is a combination of electrically tunable light absorption and Bragg reflection. In this paper, the influence of light absorption in DDPSBP‐LC by changing the dye concentration and absorption paths has been studied. Increased dye concentration can improve the contrast ratio of DDPSBP‐LC; however, the response time is the tradeoff. Increasing the cell gap can improve the contrast ratio of DDPSBP‐LC; however, the response time remains the same. The study of DDPSBP‐LC can help in shutter‐glass applications of 3‐D displays and electronic paper.     

LED‐backlight feedback control system with integrated amorphous‐silicon color sensor on an LCD panel

Abstract— Thin‐film‐transistor liquid‐crystal displays (TFT‐LCDs) have the largest market share of all digital flat‐panel displays. An LCD backlighting system employing a three‐color red‐green‐blue light‐emitting diode (RGB‐LED) array is very attractive, considering its wide color gamut, tunable white point, high dimming ratio, long lifetime, and environmental compatibility. But the high‐intensity LED has problems with thermal stability and degradation of brightness over time. Color and white luminance levels are not stable over a wide range of temperature due to inherent long‐term aging characteristics. In order to minimize color point and brightness differences over time, optical feedback control is the key technology for any LED‐backlight system. In this paper, the feasibility of an optical color‐sensing feedback system for an LED backlight by integrating the amorphous‐silicon (a‐Si) color sensor onto the LCD panel will be presented. To minimize the photoconductivity degradation of a‐Si, a new laser exposure treatment has been applied. The integrated color‐sensor optical‐feedback‐controlled LED‐backlight system minimized the color variation to less than 0.008 Δu'v' (CIE1976) compared to 0.025 for an open‐loop system over the temperature range of 42–76°C.     

Wafer‐scale monolithic hybrid integration of Si‐based IC and III–V epi‐layers—A mass manufacturable approach for active matrix micro‐LED micro‐displays

Hybridization of silicon integrated circuits (ICs) with compound semiconductor device arrays are crucial for making functional hybrid chips, which are found to have enormous applications in many areas. Although widely used in manufacturing hybrid chips, the flip‐chip technology suffers from several limitations that are difficult to overcome, especially when the demand is raised to make functional hybrid chips with higher device array density without sacrificing the chip footprint. To address those issues, Beida Jade Bird Display Limited has developed its unique wafer‐level monolithic hybrid integration technology and demonstrated its advantages in making large‐scale hybrid integration of functional device arrays on Si IC wafers. Active matrix micro‐light‐emitting diode micro‐displays with a resolution of 5000+ pixel per inch were successfully fabricated using Beida Jade Bird Display Limited's monolithic hybrid integration technology. The general fabrication method is described, and the result is presented in this paper. The fabricated monochromatic micro‐light‐emitting diode micro‐displays exhibit improved device performance than do other micro‐display technologies and have great potentials in applications such as portable projectors and near‐to‐eye projection for augmented reality. More importantly, the wafer‐scale monolithic hybrid integration technology offers a clear path for low‐cost mass production of hybrid optoelectronic IC chips.     

Highly efficient large‐sized LED display with improved ergonomics

Abstract— We have proposed a new approach to engineering and manufacturing an indoor indicator based on energy‐effective super‐bright LEDs. In our design, the light from a small number of such LEDs was uniformly redistributed using a special light guide. Recently, we developed a multi‐segment (40) LED indicator with improved ergonomics and a luminance of up to 4000 cd/m². This indicator is also capable of displaying (apart from the digits) special symbols.