PVC/G-POSS共混物的力学性能与热性能

考察了2,3-环氧丙氧乙基笼型倍半硅氧烷(G-POSS)对聚氯乙烯(PVC)共混物力学和热性能的影响。结果表明:加入G-POSS可缩短PVC的塑化时间;100 g PVC中G-POSS用量不超过7 g时共混物的拉伸强度得到提高;加入G-POSS可改善PVC的耐热性能,G-POSS用量为13 g时,共混物的维卡软化温度和初始分解温度分别提高12,27℃。     

Rheological and mechanical properties of poly(vinyl chloride)/chlorinated poly(vinyl chloride) miscible blends

The properties of poly(vinyl chlorlde)/ehlorinated poly(vinyl chloride) (61.6 percent C1) blends, prepared by melt and solution blending, were measured by various tests. Based on the chlorinated poly(vinyl chloride) (CPVC) composition, percent chlorine, and mole percent CC1₂ groups, these blends were expected to show intermediate properties between miscible and immiscible systems. Indicative of miscible behavior were the single glass transition temperatures over the entire composition range for both melt and solution blended mixtures. A single phase was also indicated by transmission electron microscopy. However, the yield stress showed a minimum value less than either of the pure components in the 50 to 75 percent CPVC range, which is characteristic of two-phased systems. Specific volume, glass transition temperature, and heat distortion temperature were linear with binary composition. The storage modulus showed a small maximum, suggesting a weak interaction between the two miscible polymers. Heats of melting for the residual PVC crystallinity were also less than expected from linear additivity. At 160°C and 210°C, the logarithm of the complex viscosity was essentially linear with volume fraction of CPVC, except for a very slight decrease in the 50 to 75 percent CPVC range, which may have been a result of lower crystallinity. At 140°C, the complex viscosity of the CPVC was less than that of PVC owing to the higher crystallinity of the latter. The viscosities were similar at 160°C, but at 210°C, where most of the crystallites had melted, the complex viscosity of the CPVC was higher because of its higher glass transition temperature.     

The effect of layered double hydroxides dispersion on thermal and mechanical properties of poly(vinyl chloride)/poly(methyl methacrylate) blends

Poly(vinyl chloride) (PVC)/layered double hydroxide (LDH) composites and PVC/poly(methyl methacrylate) (PMMA)/LDH composites were prepared via solution intercalation into PVC using both unmodified and organo‐modified LDHs and variable‐molecular‐weight PMMA as additional components. The LDH dispersion was investigated using X‐ray diffraction analysis and electron microscopy in scanning and transmission modes. Spotlight fourier transform infrared (FTIR) chemical imaging analysis was also used to obtain a deeper insight into the dispersion of polymer phases and LDH segregation. Thermal properties were determined using thermogravimetric analysis and differential scanning calorimetry; moreover, a preliminary investigation of mechanical properties in tensile mode and evaluation of the Vicat softening temperature were carried out. The morphological analysis of PVC/LDH and PVC/PMMA/LDH composites evidenced in both cases the presence of disordered micro‐aggregates with loss of the LDH crystallographic symmetry depending on the amount and molecular weight of PMMA. In particular, in the case of PVC/PMMA/LDH composites, the FTIR imaging analysis showed that PMMA mostly segregated in the LDH phase. However, even if the degree of LDH dispersion was not elevated (micro‐aggregates with disordered structures and size ranging from 0.5 up to 11 µm were evidenced), thermal stability and mechanical properties of the composites were improved with a synergic effect of PMMA and LDH. © 2013 Society of Chemical Industry     

Viscoelastic properties,morphology, and thermal stability of rigid and plasticized poly(vinyl chloride)/poly(methyl methacrylate) blends

Viscoelastic properties, morphology, and thermal stability of rigid and plasticized poly(vinyl chloride)/poly (methyl methacrylate) (PVC/PMMA) blends were studied. For that purpose, blends of variable composition from 0 to 100 wt% were prepared in the presence (15, 30, and 50 wt%) and in the absence of di(2‐ethylhexyl) phthalate as plasticizer. Their miscibility was investigated by using dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The DMTA and SEM results showed that the two polymers are miscible. Thermogravimetric studies on these blends were carried out in a flowing atmosphere of air from ambient temperature to 550°C. The results showed that the thermal degradation of rigid and plasticized PVC/PMMA in this broad range of temperature is a three‐step process and that PMMA exerted a stabilizing effect on the thermal degradation of PVC during the first step by reducing the rate of dehydrochlorination. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Investigation of thermal,mechanical and electrochemical properties of nanocomposites based on CuO modified poly(vinyl chloride)/poly(methyl methacrylate) blend

The preparation of binary polymer blend nanocomposites with different nanomaterials is a relatively new approach to achieve desired physical, thermal, mechanical, and electrochemical properties because it has the collective effects of both polymer blending and fillers. Transition metal oxides constitute a large class among those fillers because the precursors for metal oxides are abundantly available. However, very few studies have been accomplished on incorporating transition metal oxides into binary polymer blends. In this project, cuprous oxide (CuO) nanoparticles (NPs) with a crystallite size of 24.95 nm were incorporated into poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blend, and thin films of the nanocomposites were obtained through a solution casting technique. Scanning electron microscopy, X‐ray diffraction, universal testing machine testing, thermogravimetric analysis, and cyclic voltammetry were used to study morphological, crystalline, mechanical, thermal, and electrochemical properties of the nanocomposites. Scanning electron micrographs showed that the blend was completely miscible and CuO NPs were well dispersed within the matrix. Mechanical properties greatly improved with each wt% addition of CuO NPs. Thermogravimetric analysis thermograms revealed a two‐stage degradation for neat PVC/PMMA blend and CuO/PVC/PMMA. Cyclic voltammetry results indicated a free electron transfer in neat blend that further improved with the incorporation of increasing percentage of CuO NPs. J. VINYL ADDIT. TECHNOL., 23:80–85, 2017. © 2015 Society of Plastics Engineers     

Thermal and mechanical properties of electron beam irradiated poly(vinyl chloride)/polystyrene blends

The effect of electron beam irradiation on the thermal and mechanical properties of poly(vinyl chloride)/polystyrene (PVC/PS) blends and PVC/PS blends containing epoxidized natural rubber (ENR) was studied. The thermogravimetric analysis study showed that the thermal decomposition of the plasticized PVC individual polymer goes through two stages, whereas PS decomposes through one stage. However, the temperature of the maximum rate of reaction (T_max) of PS is much higher than that for PVC and their blends. Meanwhile, the T_max was found to increase with increasing PS ratios in the blend. The thermal stability of PVC/PS blends was greatly increased after electron beam irradiation in comparison with unirradiated blends. Moreover, the addition of ENR to PVC/PS increased the thermal stability. On the other hand, the mechanical properties in terms of tensile strength and elongation at break of PVC/PS blends are lower than pure PVC polymer because of the immiscibility. However, the addition of ENR to the PVC/PS (80/20) blend increased the elongation at break from 114 to 321% associated with a small effect on the tensile properties. These behaviors were supported by structure morphology studies observations, which indicate an improvement in the interfacial adhesion between the phases. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Photostability,thermal and mechanical properties of poly(vinyl chloride)/novel acrylate terpolymer blend

Methyl methacrylate/2‐hydroxyethyl methacrylate/maleic anhydride terpolymer with various compositions was synthesized, characterized and investigated as a photostabilizer for rigid polyvinyl chloride (PVC). The chemical structure of the terpolymer MMA/HEMA/MA, was confirmed by ultraviolet–visible and FTIR, spectroscopy. The molecular weights of the terpolymer were determined by applying gel permeation chromatography. The stabilizing efficiency of the terpolymer was evaluated by the determination of the weight loss of PVC/terpolymer blends after various irradiation times. The content of the formed gel as well as the intrinsic viscosity of the soluble fraction of the photodegraded polymer were also determined. The efficiency was also evaluated by measuring the extent of the discoloration of the photodegraded polymer. Thermal gravimetric analysis of the terpolymer and PVC/terpolymer blend were measured. Moreover, physicomechanical properties of photodegraded stabilized PVC samples were as well measured. The results revealed that the photostabilizing efficiency as well as thermal stability increased in the presence of the terpolymer as blended with PVC and by the increase of maleic anhydride ratio in the terpolymer. The photostabilizing efficiencies were compared with the industrially known UV absorber 2‐hydroxy‐4‐(octyloxy) phenylbenzophenone. J. VINYL ADDIT. TECHNOL., 25:E55–E62, 2019. © 2018 Society of Plastics Engineers     

Preparation method and physical,mechanical, thermal characterization of poly(vinyl alcohol)/poly(acrylic acid) blends

A series of blends of poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) were prepared by solution mixing and casting. Glycerol was used as plasticizer. The blends were characterized for their physicochemical and thermo-mechanical properties. The FTIR results revealed the molecular level interaction between PVA and PAA at all blend ratios. The incorporation of PAA significantly reduced the storage modulus of PVA at a given temperature. PVA gradually lost its crystalline character with the increase of PAA and became fully amorphous when the PAA content in the blend exceeded 50 wt%. The kinetic parameters of the semi-crystalline blends were determined using the Avarami–Erofeev model, which showed excellent fitting with the experimental data from DSC. The loss in crystallinity of PVA also contributed to an increase in swelling of the blend when the PAA content is increased. The morphology study by FE-SEM demonstrated that there is no phase separation among the blend components at all blend ratios.     

Evaluation effects of biobased plasticizer on the thermal,mechanical, dynamical mechanical properties,and permanence of plasticized PVC

Sunflower oil (SO) is a renewable resource that can be epoxidized, and the epoxidized SO has potential uses as an environmentally friendly in polymeric formulations, especially for poly (vinyl chloride) (PVC). Epoxidized sunflower oil (ESO) was prepared by treating the oil with peracetic acid generated in situ by reacting glacial acetic acid with hydrogen peroxide. Epoxidation was confirmed using spectroscopic and titration methods. ESO was used as a coplasticizer in PVC for the partial replacement of di‐(2‐ethyl hexyl) phthalate (DEHP). The effect of ESO on the thermal stability of plasticized PVC was evaluated by using synmero scale for the sheets. In presence of ESO plasticized PVC samples showed a reduction in discoloration and the number of conjugated double bonds. By using thermogravimetry, the incorporation of 15/45 of ESO/DEHP in PVC presents the lowest weight loss. The results of the shore hardness and mechanical properties showed that a proportion of DEHP could be substituted by ESO. By use of DMA, the formulation which contains 25 % wt of ESO in plasticizer system shifts the glass transition temperature (T_g) to ambient temperature. The migration phenomenon was studied on PVC based samples plasticized with DEHP and ESO in varying amounts. The migration was monitored by the weight loss percentage of the samples immersed into n‐hexane or heated in an oven. The amount of extracted or volatilized DEHP is proportional to the added ratio of ESO in plasticizer system. All of this favored the partial replacement of DEHP by ESO as biobased plasticizer for flexible PVC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Miscibility and thermal behavior of poly(vinyl chloride)/feather keratin blends

Various poly(vinyl chloride) (PVC)/feather keratin (FK) blends were prepared via a solution blending method in the presence of N,N‐dimethylformamide as a solvent. The miscibility of the blends was studied with different analytical methods, such as dilute solution viscometry, differential scanning calorimetry, refractometry, and atomic force microscopy. According to the results obtained from these techniques, it was concluded that the PVC/FK blend was miscible in all the studied compositions. Specific interactions between carbonyl groups of the FK structure and hydrogen from the chlorine‐containing carbon of the PVC were found to be responsible for the observed miscibility on the basis of Fourier transform infrared spectroscopy. Furthermore, increasing the FK content in the blends resulted in their miscibility enhancement. The thermal stability of the samples, as an important characteristic of biobased polymer blends, was finally examined in terms of their FK weight percentage and application temperature. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Miscibility in poly(vinyl chloride)/chlorinated poly(vinyl chloride) blends,and blends of different chlorinated poly(vinyl chlorides)

Blends of poly(vinyl chloride) with chlorinated poly(vinyl chloride) (PVC), and blends of different chlorinated poly(vinyl chlorides) (CPVC) provide an opportunity to examine systematically the effect that small changes in chemical structure have on polymer-polymer miscibility. Phase diagrams of PVC/CPVC blends have been determined for CPVC's containing 62 to 38 percent chlorine. The characteristics of binary blends of CPVC's of different chlorine contents have also been examined using differential calorimetry (DSC) and transmission electron microscopy. Their mutual solubility has been found to be very sensitive to their differences in mole percent CCl₂ groups and degree of chlorination. In metastable binary blends of CPVC's possessing single glass transition temperatures (T_g) the rate of phase separation, as followed by DSC, was found to be relatively slow at temperatures 45 to 65° above the T_g of the blend.     

Crystallization,morphology, and electrical properties of bio‐based poly(trimethylene terephthalate)/poly(ether esteramide)/ionomer blends

Bio‐based poly(trimethylene terephthalate) (PTT) and poly(ether esteramide) (PEEA) blends were prepared by melt processing with varying weight ratios (0–20 wt %) of ionomers such as lithium‐neutralized poly(ethylene‐co‐methacrylic acid) copolymer (EMAA‐Li) and sodium‐neutralized poly(ethylene‐co‐methacrylic acid) copolymer (EMAA‐Na). The blends were characterized by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), polarized light microscopy (PLM), and transmission electron microscopy (TEM). DSC and PLM results showed that EMAA‐Na increased the crystallization rate for PTT significantly, whereas EMAA‐Li did not enhance the crystallization rate at all. Specific interactions between PEEA and ionomers were confirmed by DSC and TEM. Electrostatic performance was also investigated for those PTT blends because PEEA is known as an ion‐conductive polymer. Here, we confirmed that both sodium and lithium ionomers work as a synergist to enhance the static decay performance of PTT/PEEA blends. Morphological study of these ternary blends systems was conducted by TEM. Dispersed ionomer domains were encapsulated by PEEA, which increases the interfacial surface area between PEEA and the PTT matrix. This encapsulation effect explains the unexpected synergy for the static dissipation performance on addition of ionomers to PTT/PEEA blends. This core–shell morphology can be predicted by calculating spreading coefficient for the ternary blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Dynamic mechanical behavior of poly(vinyl chloride)/poly(methyl methacrylate) polymer blend

A poly(vinyl chloride) (PVC)/poly(methyl methacrylate) (PMMA) (80/20 w/w) polymer blend was studied by mechanical spectroscopy. Two relaxations can be distinguished: in the glassy state, a very large secondary relaxation in the range of 100 K to 325 K which results from the combination of secondary relaxations of PVC and PMMA; and only one main relaxation at 364 K associated to the glass rubber transition. The relaxation spectrum in the range of the β relaxation has been described by a relaxation time distribution function based upon a Gaussian function and a series-parallel model. The α relaxation was studied by means of a theoretical approach for the nonelastic deformation of polymers. We found that the miscibility of this blend appears to be a function of the observation scale: the PVC/PMMA blend is heterogeneous at the scale of molecular movements involved for the β relaxation process but homogeneous at the scale of the chain segments responsible for the α relaxation dynamics. © 1996 John Wiley & Sons, Inc.     

Investigation of the thermal,mechanical and morphological properties of poly(vinyl chloride)/polyhedral oligomeric silsesquioxane nanocomposites

Research into organic–inorganic nanocomposites has recently become popular, particularly the development of new polymer nanocomposites. Compared to pristine polymers or conventional composites, these nanocomposites exhibit improved properties. The storage modulus of a poly(vinyl chloride) (PVC)/polyhedral oligomeric silsesquioxane (POSS) nanocomposite slightly decreased with POSS content, but had a higher modulus from 50 to 100 °C. Some of the material appeared to be aggregated with 1 wt% POSS in the polymeric matrix. Conversely, with a POSS content of 5 wt%, a better dispersion of the nanoparticles was observed. The presence of POSS in the plasticised PVC compound had little influence on the final properties of the nanocomposites, showing weaker interactions between the POSS and the plasticised PVC compound. Copyright © 2010 Society of Chemical Industry     

Study on thermal,mechanical and morphological properties of recycled poly(vinyl chloride)/fly ash composites

The present study deals with the development of composite materials utilizing recycled poly(vinyl chloride) (r‐PVC) recovered from waste electrical and electronic materials and waste fly ash obtained from thermal power plants. The effect of the incorporation of fly ash on the mechanical, thermal and morphological properties of the r‐PVC matrix was studied. The primary characterization of r‐PVC and fly ash was done employing FTIR, EDX, particle size analysis and XRD analysis. Subsequently, fly ash with a particle size of approximately 9.29 μm was incorporated within the r‐PVC matrix. Composite sheets were prepared using a melt blending process followed by compression moulding. The mechanical test revealed an increase in the tensile strength and elongation at break of the r‐PVC/fly ash composite up to 30 wt% loading of fly ash beyond which there was a decrease in the tensile strength. The impact strength, however, decreased with increasing fly ash content in the r‐PVC matrix. The morphological properties of the composites showed a good distribution of the filler within the recycled matrix. The thermal properties of r‐PVC also improved with the incorporation of fly ash which was revealed from DSC and TGA studies. The water absorption test showed an increase in water uptake with the addition of fly ash in the r‐PVC matrix. © 2020 Society of Chemical Industry     

Effect of thermal annealing on plasticizer migration in poly(vinyl chloride)/dioctyl phthalate system

Plasticizer migration studies dealing with poly(vinyl chloride) (PVC) sheets and liquid surrounding media revealed two parallel phenomena, migration of plasticizer and liquid penetration, that take place simultaneously. The present work was focused on correlating the structural differences of the PVC material with the aforementioned processes. The plasticizer and the liquid medium used were dioctyl phthalate and isopropanol, respectively. Emphasis was placed on any rearrangement of the polymer morphology occurring when elevated test temperatures were employed for a relatively long period of time (crystallization). The result was that the PVC structure seemed to become more compact, forcing the liquid medium that had already penetrated to come out. Furthermore, these experiments showed that plasticizer migration and liquid penetration were related to the polymer structure. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1780–1786, 2001     

The surface modification of diatomite,thermal, and mechanical properties of poly(vinyl chloride)/diatomite composites

Pristine diatomite was first purified by acid treatment and then modified with γ‐methacryloxy propyl trimethoxysilane molecule (KH570) to introduce hydrophobic chains on the surface of acid‐treated diatomite. Fourier‐transform infrared spectroscopy and thermogravimetric analysis (TGA) indicated that the silane coupling agent (KH570) was successfully grafted on the diatomite through covalent bonding. The digital photos showed that the silanization process changed the surface property of the diatomite. The poly(vinyl chloride) (PVC)/pristine diatomite and PVC/modified diatomite composites were prepared via two‐roll mill. The thermal stability and mechanical properties of PVC composites were investigated by TGA, mechanical properties tests, and dynamic mechanical analysis. The results showed that the thermal stability of the composites improved and maximum weight loss temperature (T_max) of the PVC composite with 1 phr modified diatomite was about 20°C higher than that of PVC composite without diatomite. The PVC/modified diatomite composites exhibited better mechanical properties owing to the stronger interfacial interaction between PVC matrix and modified diatomite. But the impact strength reduced sharply when the addition of diatomite was more than 1 phr. The reason of the phenomenon is that the diatomite plays the role of defects in PVC and it works against the absorption of impact strength energy. It was proved by the results of scanning electron microscopy. J. VINYL ADDIT. TECHNOL., 25:E39–E47, 2019. © 2018 Society of Plastics Engineers     

Evaluation of the effects of biobased plasticizers on the thermal and mechanical properties of poly(vinyl chloride)

Blends were prepared of poly(vinyl chloride) (PVC) with four different plasticizers; esters of aconitic, citric, and phthalic acids; and other ingredients used in commercial flexible PVC products. The thermal and mechanical properties of the fresh products and of the products after 6 months of aging were measured. Young's modulus of the PVC blends was reduced about 10‐fold by an increase in the plasticizer level from 15 to 30 phr from the semirigid to the flexible range according to the ASTM classification, but a 40‐phr level was required for PVC to retain its flexibility beyond 6 months. At the 40‐phr level, tributyl aconitate performed better than diisononyl phthalate (DINP) or tributyl citrate, in terms of lowering Young's modulus, both in the fresh materials and those aged for 6 months. The effects of the four plasticizers on the glass‐transition temperature (T_g) were similar, with T_g close to ambient temperature at the 30‐ and 40‐phr levels in freshly prepared samples and at 40–60°C in those aged for 6 months. The thermal stability of the PVC plasticized with DINP was superior among the group. Overall, tributyl aconitate appeared to be a good candidate for use in consumer products where the alleged toxicity of DINP may be an issue. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1366–1373, 2006     

Fracture behavior of poly(vinyl chloride)/methyl methacrylate/butadiene/styrene polymer blends

The fracture mode of poly(vinyl chloride)/methyl methacrylate/butadiene/styrene (PVC/MBS) polymer blends can change from ductile to brittle in accordance with the changes in shape of the test specimen or test conditions. Therefore, the mechanisms of impact energy absorption and the main cause of stress whitening are complicated. The following results on PVC/MBS blends were obtained by carrying out fracture experiments at different test speeds and temperatures:

• (1) The ductile/brittle fracture mode of the PVC and PVC/MBS blends can be explained by σ (the craze initiation stress)/σ_y (the shear yield initiation stress), which depends on the strain rates and temperature.
• (2) The fracture behavior of the PVC/MBS blends can be classified into the following types from the standpoints of fracture mode and whitening degree: Fracture I: ductile fracture without whitening; Fracture II: ductile fracture with whitening; and Fracture III: brittle fracture without whitening.
• (3) The following concepts can be estimated from the measurements of yield stress, specific gravity and SEM, TEM and visual observations. In Fracture I, shear yield occurs mainly. In Fracture II, both shear yield and crazing occur. In Fracture III, deformation of the rubber and local crazing occur.
• (4) The main cause of stress whitening in PVC/MBS blends is light scattering by cavities in the rubber particles.
• (5) In Fracture II, at first, crazes with cavities in the rubber particles occur. Then, shear yield occurs. Finally, crazes are healed by the heat, and only the cavities in the rubber remain.

     

Phase separation and mechanical properties of poly(methyl methacrylate)/polycarbonate blends

Dynamic mechanical properties, tensile properties, and scanning electron microscopy of blends of poly(methyl methacrylate) and polycarbonate were investigated after phase separation above their cloud point temperature by annealing in a hot press. The dynamic mechanical properties show that phase separation proceeds more distinctly for the blends annealed at higher temperature and for longer time. The scanning electron micrographs show that the morphology of phase separated blends varies with the conditions of heat treatment. The tensile properties of phase separated blends deteriorate on account of the coarsening of the brittle dispersed phase over the optimum size and the occurrence of voiding during the heat treatment.