A balanced dual‐band bandpass filter with a wide stopband and controllable differential‐mode frequencies and fractional bandwidths

In this article, a balanced microstrip dual‐band bandpass filter (BPF) is designed. The proposed filter is achieved by employing a microstrip U‐shape half‐wavelength resonator, a folded stub‐loaded resonator and balanced microstrip/slotline transition structures. The center frequencies and the fractional bandwidths of the two differential‐mode (DM) passbands can be controlled independently by changing the physical lengths of the two resonators and the gaps between each resonator, respectively. The balanced microstrip/slotline transition structures can achieve a wideband common‐mode (CM) suppression. Meanwhile, the DM passbands are independent from the CM responses, which significantly simplify the design procedure. In addition, a wide DM stopband is also realized. In order to validate the design strategies, a balanced dual‐band BPF centered at 2.57 and 3.41 GHz was fabricated and a good agreement between the simulated and measured results is observed.     

Compact dual‐band bandpass filter and diplexer using hybrid resonant structure with independently controllable dual passbands

In this article, a compact dual‐band bandpass filter (BPF) is developed using a hybrid resonant structure, which consists of a microstrip stub‐loaded dual‐mode resonator and a slotline stub‐loaded dual‐mode resonator. These two resonators, both having two controllable resonant modes and one transmission zero (TZ), are analyzed and used to construct two desired passbands of a dual‐band BPF. Multiple TZs are generated by introducing a source‐load coupling, thus improving the selectivity of the passbands. Then, the dual‐band BPF is reshaped to configure a compact diplexer. The inherent TZs of the two proposed resonators are designed to improve the frequency property and port isolation of the diplexer. Finally, a dual‐band BPF and a diplexer with the lower and upper passbands centered at 2.45 and 3.45 GHz, respectively, are designed, fabricated, and measured to verify the proposed structure and method.     

A balanced dual‐band bandpass filter with independently tunable differential‐mode frequencies

A balanced dual‐band bandpass filter (BPF) with independently tunable differential‐mode (DM) frequencies is proposed in this letter. The proposed BPF is composed of complementary split‐ring resonators (CSRRs) etched on the ground and varactors loaded on the resonators. A balanced stepped‐impedance microstrip‐slotline transition structure is introduced to transfer the DM signals successfully and block the common‐mode (CM) signals transmission. Good DM transmission and CM suppression can be achieved. Moreover, by changing the reverse bias voltages of the varactors loaded on coupling CSRRs, two DM resonant frequencies of the proposed balanced BPF can be tuned independently. To verify the feasibility of the design method, a balanced BPF with DM frequency ranging from 0.80 GHz to 1.12 GHz and 1.55 GHz to 2.05 GHz is fabricated and measured. Good agreement between the simulation and measurement results demonstrate the validity of the design.     

A tunable balanced dual‐band BPF with quasi‐independently controlled center frequency and bandwidth

In this paper, a balanced dual‐band bandpass filter (BPF) with high selectivity and low insertion loss performance is presented by employing stub loaded resonators (SLRs) and stepped impedance resonators (SIRs) into balanced microstrip‐slotline (MS) transition structures. The balanced MS transition structures can achieve a wideband common‐mode (CM) suppression which is independent of the differential‐mode (DM) response, significantly simplifying the design procedure. Six varactors are loaded into the resonators to achieve the electrical reconfiguration. The proposed balanced dual‐band BPF can realize quasi‐independently tunable center frequencies and bandwidths. A tuning center frequency from 2.48 to 2.85 GHz and a fractional bandwidth (20.16%‐7.02%) with more than 15 dB return loss and less than 2.36 dB insertion loss are achieved in the first passband. The second passband can realize a tuning center frequency from 3.6 to 3.95 GHz with more than 12 dB return loss and less than 2.38 dB insertion loss. A good agreement between the simulated and measured results is observed.     

A balanced dual‐band BPF with independently controllable frequencies and bandwidths

A balanced second‐order dual‐band bandpass filter (BPF) with independently controllable center frequencies and bandwidths based on coupled stepped‐impedance resonators (SIRs) is designed in this article. To obtain a dual‐band differential‐mode (DM) response, two pairs of SIRs with different resonant frequencies are employed in the design. The bandwidths of the two DM passbands can be independently tuned by adjusting the coupling gaps and coupling lengths of the corresponding resonators. In addition, three transmission zeros are realized to enhance the selectivity of the DM passbands. The microstrip‐slotline transition structure is utilized to achieve a wideband common‐mode (CM) suppression. Moreover, the DM responses are independent of the CM ones, which significantly simplify the design procedure. Finally, a balanced dual‐band BPF is designed to validate the design method and a good agreement between the simulated and measured results is observed.     

Compact Dual‐/Tri‐/Quad‐Band banpass filters using shorted stub loaded stepped‐impedance resonator

In this article, the shorted stub loaded stepped‐impedance resonator (SSLSIR) with the individually tunable first even resonant mode and first odd resonant mode is applied to design dual‐, tri‐, and quad‐band bandpass filters (BPFs). The SSLSIR dual‐band BPF with asymmetrical coupling is realized using the first even resonant modes and the first odd resonant modes of a set of SSLSIRs. Then, the high‐impedance feeding lines of SSLSIR dual‐band BPF is modified to produce a new passband, and thus a new tri‐band BPF is realized. The proposed quad‐band BPF consists of two sets of SSLSIRs with symmetrical coupling. Each of the designed circuits occupies a very compact size and has a good in‐band out‐of‐band performance. Good agreements are observed between the simulated and measured results. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:601–609, 2015.     

An X‐band push‐push oscillator with parallel feedback configuration designed by microstrip balanced bandpass filter

In this article, a push‐push oscillator with parallel feedback configuration designed by the microstrip balanced bandpass filter (BPF) is proposed. The push‐push oscillator consists of two sub‐oscillators with a balanced BPF. The balanced BPF with the open‐circuited stubs exhibits the desired differential‐mode frequency response and achieves high common‐mode suppression simultaneously. Based on the technique of the balanced BPF, the out‐of‐phase fundamental signals and odd harmonic signals are canceled out while the even harmonic signals are well combined. The prototype of the push‐push oscillator is designed and fabricated. Measured results show that the proposed push‐push oscillator works at 9.96 GHz of the second harmonic frequency. The actual output power is ?8.57 dBm. The rejection of the fundamental signal and third harmonic signal are better than 27 and 42 dBc, respectively. The phase noise of the proposed push‐push oscillator is ?128.3 dBc/Hz at 1 MHz frequency offset.     

Compact differential dual‐band bandpass filter using single quad‐mode metal‐loaded dielectric resonator

This letter presents a novel miniaturized differential dual‐band bandpass filter (BPF) using a single quad‐mode metal‐loaded dielectric resonator (DR). The differential dual‐band BPF is designed in a single‐cavity configuration with one quad‐mode DR and four feeding probes, featuring compact size. The rectangular DR is directly mounted on the bottom of the metal cavity and covered by a metal plate on the top surface. It allows two pairs of orthogonal modes (LSE₁₀ and LSM₁₀), which can be differentially excited and coupled by introducing proper perturbation for constructing dual‐band differential‐mode frequency response. To validate the proposed idea, a compact differential BPF with good performance using a quad‐mode DR cavity is designed, fabricated, and measured. The simulated and measured results with good agreement are presented.     

Design of high selectivity tri‐band bandpass filter with wide upper stopband

This article presents a dual‐plane structure high selectivity tri‐band bandpass filter (BPF) which consists of a pair of T‐shaped microstrip feed lines with capacitive source‐load coupling as well as spur lines embedded, and three resonators, i.e., a dual‐mode stub‐loaded stepped impedance resonator and two nested dual‐mode defected ground structure resonators. Using the intrinsic characteristics of the resonators and feed lines, nine transmission zeros near the passband edges and in the stopband can be generated to achieve high selectivity. An experimental tri‐band BPF located at 2.4/5.7 GHz [wireless local area networks (WLAN) application] and 3.5 GHz [worldwide interoperability for microwave access (WiMAX) application] has been simulated and fabricated. Good agreement between the simulated and measured results validates the design approach. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

A novel triple notch‐bands ultra wide‐band band‐pass filters using parallel multi‐mode resonators and CSRRs

This article discusses a technique based on combination of multimode resonators (MMR) and complementary split ring resonators (CSRR) to design multi notch‐bands ultra wide‐band (UWB) band‐pass filters (BPF). The proposed structure consists of two parallel multimode resonators, resulting in a dual notch‐band UWB BPF, integrated with a single cell of CSRR to realize the third notch‐band. The mechanism of realizing the notch‐bands is mathematically presented and a triple notch‐bands UWB BPF is designed, simulated and fabricated. The overall size of the proposed filter is reported to be around 36 × 7.7 mm² where a size reduction of around 35% is demonstrated in comparison to the conventional filter. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:375–381, 2014.     

Multi‐mode resonators with quad‐/penta‐/sext‐mode resonant characteristics and their applications to bandpass filters

In this article, a new class of dual‐/tri‐band and ultra‐wideband (UWB) bandpass filters (BPFs) using novel multi‐mode resonators are proposed. The classical even‐/odd‐mode method is applied to analyze the resonant characteristics of the proposed resonators, which exhibit controllable resonant modes with different dimension parameters under the same configuration. According to the analysis, three resonators with quad‐/penta‐/sext‐mode resonant characteristics are obtained by choosing the specific dimension parameters. Then, the quad‐mode resonator is used to design a dual‐wideband BPF centred at 2.39/5.14 GHz with 3‐dB fractional bandwidths (FBWs) of 36.9%/18.9%, and the penta‐mode resonator is utilized to design an UWB BPF with 3‐dB FBW of 102.2%, whereas the sext‐mode resonator is applied to design a tri‐band BPF with centre frequencies of 2.09/3.52/5.46 GHz and 3‐dB FBWs of 11.3%/20%/12.1%. All these three filters are fabricated and measured, and the measured results are in good agreement with the simulated ones.     

Compact ultra‐wideband bandpass filter with configurable stopband based on diamond‐shape resonator

An ultra‐wideband compact bandpass filter (BPF) with configurable stopband by tuning transmission zeroes is proposed in this paper. The ultra‐wideband bandpass response is based on a diamond‐shape resonator consisting of a pair of broadside coupled diamond‐shape microstrip lines, within which a diamond shape defected ground structure (DGS) is etched in the middle. Flexible transmission zeros realized by open and short stubs can be easily adjusted to improve band selectivity and harmonic suppression. Measurement result shows that the dedicated device has a 3 dB fractional bandwidth of 148% (0.94‐6.36 GHz) with 20 dB rejection stopband from 6.87 to 9.7 GHz (77.5%) which agrees good with the simulate performance. The overall size of the proposed BPF is 0.27 λ_g × 0.23 λ_g.     

Inter‐digital coupled dual‐mode patch resonator with crossed‐island configuration for tri‐band filter design

The miniaturized dual‐mode tri‐band band‐pass filters (BPF) using crossed‐island patch resonator is proposed in this article. The BPF is mainly formed by a square patch resonator in which a crossed‐island configuration is embedded in the patch. The patch size reduction with 74.4% is achieved. By the perturbation and the alternative inter‐digital coupling, the tri‐band responses are obtained. The proposed filter covers the required bandwidths for WLAN band (2.26–3.11 GHz and 5.02–6.0 GHz) and X‐band (7.58–8.41 GHz) applications. Five transmission zeros are placed between three pass‐bands and resulted in a good isolation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:457–463, 2014.     

Compact dual‐ and triband bandpass filter using frequency selecting coupling structure loaded stepped‐impedance resonator

This article presents two novel resonators, that is, frequency selecting coupling structure loaded stepped‐impedance resonator (FSCSLSIR) and π‐section loaded FSCSLSIR. The resonator behaviors and guidelines are given to design FSCSLSIR dual‐band bandpass filter (BPF) and π‐section loaded FSCSLSIR triband BPF. The proposed dual‐ and triband BPF have very compact sizes of 0.13 λ_gd × 0.06 λ_gd and 0.115 λ_gt × 0.074 λ_gt, respectively. Moreover, good return loss, low insertion loss, and high band‐to‐band isolation can be observed, and the proposed FSCSLSIR dual‐band BPF has an ultrawide stopband from 5.79 to 36 GHz. The experimental results are in good agreement with the simulations. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:427–435, 2015.     

A highly selective balanced wideband bandpass filter based on nested split‐ring resonators

A balanced wideband bandpass filter (BPF) with a high frequency selectivity, controllable bandwidth, and good common‐mode (CM) suppression based on nested split‐ring resonators (SRRs) is proposed in this article. The proposed nested SRRs are applied to form three transmission poles (TPs) that can achieve a wide differential‐mode (DM) passband centered at 3.0 GHz. Meanwhile, two transmission zeros (TZs) are generated to realize a high frequency selectivity of the DM passband. Moreover, TPs and TZs can be quasi‐independently controlled by changing the physical lengths of SRRs and the gaps between them, which can greatly improve the flexibility and practicality of the design. The proposed balanced BPF is fed by balanced microstrip‐slotline (BMS) transition structures. For the CM signals, the BMS transition structures can achieve a good wideband CM suppression without affecting the DM ones, thereby simplifying the design procedure. In order to validate its practicability, a balanced wideband BPF is fabricated and a good agreement between the simulated and measured results is obtained.     

Dual‐mode resonator with modified dual‐square‐Loop for WLAN and WiMAX quad‐band filter design

We propose the improved configurations with dual‐mode dual‐square‐loop resonators (DMDSLR) for quad‐band bandpass filter (BPF) design. The modified DMDSLR filter employs two sets of the loops. The square loop is designed to operate at the first and third resonated frequencies (2.4/5.22 GHz) and the G‐shaped loop is employed at the second and fourth resonated frequencies (3.59/6.6 GHz). The resonant frequency equations of DMDSLR are introduced for simply designing quad‐band BPF. Resonant frequencies can be controlled by tuning the perimeter ratio of the square loops. A systematic design procedure with the design map is applied for accuracy design. To obtain lower insertion loss, higher out‐of‐band rejection level and wider bandwidth of quad‐band, the miniaturized DMDSLR with meander‐line technique is proposed. The proposed filters are successfully simulated and measured showing frequency responses and current distributions. It can be applied to WLAN and WiMAX quad‐band systems. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:332–340, 2014.     

Hybrid wideband dual‐cylindrical circularly polarized dielectric resonator antennas excited with S‐shaped microstrip feed for sub‐6 GHz frequency range

In this article, a hybrid microstrip fed dual‐cylindrical dielectric resonator antenna (dual‐CDRA) has been proposed for the sub‐6 GHz band application with a wide circular polarization band. The proposed hybrid microstrip feed cylindrical dielectric resonator antenna utilizes an S‐shaped microstrip feed line to excite fundamental HE_11δ like mode and hybrid mode in dual‐CDRAs. The presented antenna structures are acting as monopole antenna separately with 48.75% (3.88‐6.38 GHz) bandwidth whereas both radiators called dual‐CDRAs enhances the bandwidth up to 93.06% (2.16‐5.92 GHz) in addition with an axial ratio bandwidth of 15.2% (3.52‐4.1 GHz). The proposed antenna is applicable for WiMAX (3.4‐3.69 GHz), and WLAN application of 802.11d and 8.02.11e IEEE standard. For validation of simulated results, an antenna prototype has been fabricated and experimentally verified. A good agreement between simulation and measured results are obtained. The simulation results have been carried out by using Ansys HFSS 14.0 version software.     

A dual‐band dual‐mode microstrip Yagi antenna with quasi‐end‐fire radiation

A dual‐band dual‐mode microstrip Yagi antenna with quasi‐end‐fire radiation patterns is proposed in this paper. It consists of five radiating patches driven by a single slot‐loaded patch placed in the middle. Meanwhile, two slot‐loaded parasitic patches are symmetrically located on two sides of the driven patch, respectively. In the lower band, the five patches involved resonate at TM₀₁ mode. While in the upper band, all the patches resonate at TM₀₂ mode. In order to ensure quasi‐end‐fire radiations in the both bands, four slots are symmetrically etched around the strongest surface currents of each patch resonating at TM₀₂ mode. As a result, the resonant frequency of TM₀₂ mode is decreased dramatically, while the resonant frequency of TM₀₁ mode almost remains unchanged. With these arrangements, the separations between any two of the adjacent patches at their centers satisfy the requirements in design of the microstrip Yagi antenna in both bands, so as to realize the dual‐band dual‐mode microstrip Yagi antenna on a single‐layer substrate. Finally, an antenna prototype is fabricated and tested. The measured results reveal that the dual operating bands of 2.76~2.88 and 4.88~5.03 GHz for |S₁₁| < ?10 dB are satisfactorily achieved. Most importantly, the proposed antenna can indeed realize the quasi‐end‐fire radiation patterns in dual operating bands.     

Dual‐band band pass filter using stub‐loaded open‐loop resonators with wide controllable bandwidths

Two dual‐band band pass filters (BPF) using stub‐loaded open‐loop (SLOL) resonator are presented in this article. A novel coupling tuning method by changing the relative coupling position of the resonators is proposed to control the bandwidth of each passband in a wide range. Transmission zeros are created to improve the selectivity by source‐load coupling. Because of the large ratio of two bandwidths, a novel dual‐band matching method is proposed to match the different load impedances at two passband frequencies to the same source impedance. Hence, relax the fabrication requirement of gap. The proposed dual‐band band pass filter is designed and fabricated. The measured 3 dB fractional bandwidths (FBWs) of two 2.45/5.25 GHz dual‐band BPFs are 6.5%/14.5% and 9.8%/5.5%, respectively. The results are in good agreement with the simulation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:367–374, 2014.     

Compact wideband microstrip bandpass filter with wide upper stopband based on coupled‐stub loaded resonator

A novel wideband microstrip bandpass filter (BPF) based on a coupled‐stub loaded resonator (CSLR) is presented in this article. The CSLR is constructed by attaching one short‐circuited parallel coupled microstrip line (PCML) in shunt to a high impedance microstrip line. The filter bandwidth can be conveniently controlled via reasonable adjusting of the impedance of PCML. Moreover, new defected microstrip structures (DMSs) introduced in the PCML functions as a means of adjusting the positions of transmission zeros, created by the PCML. The resonant mode and transmission zero chart are given, indicating that the higher modes could be suppressed by the transmission zeros. Finally, to validate the proposed method, two wideband BPF filters with and without DMSs centered at 3 GHz with 3 dB fractional bandwidth of 87% are designed and fabricated. The measured results show that both the return losses are better than 15.8 dB, while the BPF with DMSs has a ?19.4 dB isolation wideband from 1.57 to 4.23 . The measured results are in excellent agreement with full‐wave electromagnetic simulation results. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:122–128, 2015.