Solidification Microstructure of Aluminum AA 6016-T4 Resistance Spot Welds Using a Short-Pulse Technique

The influence of the duration of the current pulse on the solidification microstructure of resistance spot welded (RSW) samples of aluminum alloy 6016-T4 with the short-pulse technique was investigated through experiments and numerical modeling. Microstructure was analyzed in terms of morphology and size, and primary and secondary dendrite arm spacing were measured on experimental samples. A reduction in pulse width resulted in a fine, columnar-dendritic microstructure in the outer regions of the fusion zone as well as a larger equiaxed-dendritic zone in the fusion zone center. A two-dimensional, axisymmetric finite element model of the spot welding process with new methods for calculation of the solidification parameters G (thermal gradient in the solid behind the solid–liquid interface) and R (velocity of the solid–liquid interface) was used for investigation of influence of pulse time on solidification microstructure and comparison to experimental results. Morphological trends in the solidification structure showed good agreement between experiments and simulations, and the influence of the pulse duration on the solidification parameters evolved because of changing heat transfer conditions. Simulated solidification data suggest that the solidification of aluminum during RSW falls in the regime of rapid solidification.

     

Modeling of irregular eutectic microstructures in solidification of Al-Si alloys

A modified cellular automaton (MCA) model was developed and applied to simulate the evolution of solidification microstructures of both eutectic and hypoeutectic Al-Si alloys. The present MCA model considers the equilibrium and metastable equilibrium solidification processes in a multiphase system. It accounts for the aspects including the nucleation of a new phase, the growth of primary α dendrites and two eutectic solid phases from a single liquid phase, as well as the coupling between the phase transformation and solute redistribution in liquid. The effects of alloy composition and eutectic undercooling on eutectic morphology and eutectic nucleation mode were investigated. The simulated results were compared with those obtained experimentally.     

Room temperature compressive properties and strengthening mechanism of Mg_(96.17)Zn_(3.15)Y_(0.50)Zr_(0.18) alloy solidified under high pressure

The microstructures of Mg_(96.17)Zn_(3.15)Y_(0.50)Zr_(0.18) alloys solidified under 2-6 GPa high pressure were investigated by employing SEM(EDS) and TEM.The strengthening mechanism of experimental alloy solidified under high pressure is also discussed by analyzing the compressive properties and compression fracture morphology.The results show that the microstructure of experimental alloy becomes significantly fine-grained with increasing GPa level high pressure during solidification process,and the secondary dendrite arm spacing reduces from 40 μm at atmospheric pressure to 10 μm at 6 GPa pressure.The morphology of the second phases changes from the net structure by the lamellar-type eutectic structure at atmospheric pressure to discontinuous thin rods or particles at 6 GPa pressure.Besides,the solid solubility of Zn in the Mg matrix is improved with the increase of the solidification pressure.Compared with atmospheric-pressure solidification,high-pressure solidification can improve the strength of the experimental alloy.The compressive stre ngth is improved from 263 to 437 MPa at 6 GPa.The fracture mechanism of the experimental alloy changes from cleavage fracture at atmospheric pressure to quasi-cleavage fracture at high pressure.The main mechanism of the strength improvement of the experimental alloy includes the grain refinement strengthening caused by the refinement of the solidification microstructure,the second phase strengthening caused by the improvement of the morphology and distribution of the second phases,and solid solution strengthening caused by the increase of the solid solubility of Zn in the Mg matrix.     

Application of electromagnetic separation of phases in alloy melt to produce <Emphasis Type="Italic">In-situ</Emphasis> surface and functionally gradient composites

The principle of electromagnetic separation of phases (primary phase) in alloy melt is that the electromagnetic force scarcely acts on the primary phases due to its low electric conductivity as compared to the melt. As a result, a repulsive force acts on the primary iron-rich phases to push them to move in the direction opposite to that of the electromagnetic force. The in-situ surface composite and the functionally gradient composite reinforced by primary Si are produced when the hypereutectic Al-Si alloy solidifies under electromagnetic force induced by static magnetic field and DC current. Similarly, the Al-Si-1.20 pct Fe-1.60 pct Mn alloy in-situ surface composite reinforced by primary iron-rich phase is produced. Based on this, a new method for production of in-situ multigradient composite with several layers, by electromagnetic separation of phases and directional solidification technique, is proposed.     

Improving the fracture toughness of constituent phases and Nb-based <Emphasis Type="Italic">in-situ</Emphasis> composites by a computational alloy design approach

A computational alloy design approach has been used to identify a ductile matrix for Nb-based in-situ composites containing Ti, Hf, Cr, Si, and Ge additions. Candidate alloys in the form of cast buttons were fabricated by arc melting. Coupon specimens were prepared and heated treated to vary the microstructure. Backscattered electron (BSE) microscopy, quantitative metallography, energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD) were utilized to characterize the morphology, volume fraction, composition, and crystallography of individual phases in the microstructure. The fracture toughness of the composites was characterized by three-point bending and compact-tension techniques, while the fracture toughness of individual phases in the in-situ composites was determined by an indentation technique. The composition, crystallography, and volume fraction of individual phases were correlated with the fracture-toughness results to assess (1) the role of constituent properties in the overall fracture resistance of the composites and (2) the effectiveness of the computational design approach. The results indicated that the effects of alloy addition and plastic constraint on fracture toughness were reasonably predicted, but the conditions for relaxing plastic constraint to attain higher fracture toughness were not achieved.     

Effect of Ag Content on the Microstructure and Crystallization of Coupled Eutectic Growth in Directionally Solidified Al-Cu-Ag Alloys

A series of coupled eutectic growths along the univariant eutectic groove in the ternary Al-Cu-Ag alloy was studied to investigate the effect of Ag on the microstructure and crystallization of directionally solidified Al-Cu-Ag alloys. The results indicated that the eutectic morphology and orientation relationship (OR) between eutectic phases were modified as the Ag content in the Al-Cu-Ag alloys increased. At a lower growth velocity (R ≤ 1 μm/s), a banded structure formed and the interlamellar spacing decreased with the increasing Ag content. At a higher growth velocity (R ≥ 3 μm/s), the eutectic cell spacing decreased with increasing Ag content. Increasing the Ag content in the Al-Cu-Ag alloys enhanced the enrichment of the Ag solute in the liquid ahead of the quenched liquid/solid interface. In addition, increasing the Ag content in the Al-Cu-Ag alloys promoted the transformation from a “Beta 6” OR to an “Alpha 4” OR between eutectic phases. Modifications of the eutectic morphology and the OR during directional solidification were attributed to the enrichment of Ag content at the solid/liquid interface and the changes in the interfacial energy due to the increase in Ag solubility in the α-Al phase.

     

Equiaxed dendritic solidification with convection: Part I. Multiscale/multiphase modeling

Equiaxed dendritic solidification in the presence of melt convection and solid-phase transport is investigated in a series of three articles. In part I, a multiphase model is developed to predict com-position and structure evolution in an alloy solidifying with an equiaxed morphology. The model accounts for the transport phenomena occurring on the macroscopic (system) scale, as well as the grain nucleation and growth mechanisms taking place over various microscopic length scales. The present model generalizes a previous multiscale/multiphase model by including liquid melt convec-tion and solid-phase transport. The macroscopic transport equations for the solid and the interdendritic and extradendritic liquid phases are derived using the volume averaging technique and closed by supplementary relations to describe the interfacial transfer terms. In part II, a numerical application of the model to equiaxed dendritic solidification of an Al-Cu alloy in a rectangular cavity is dem-onstrated. Limited experimental validation of the model using a NH₄C1-H₂O transparent model alloy is provided in part III.     

Cellular Automaton Study of Hydrogen Porosity Evolution Coupled with Dendrite Growth During Solidification in the Molten Pool of Al-Cu Alloys

Welding porosity defects significantly reduce the mechanical properties of welded joints. In this paper, the hydrogen porosity evolution coupled with dendrite growth during solidification in the molten pool of Al-4.0 wt pct Cu alloy was modeled and simulated. Three phases, including a liquid phase, a solid phase, and a gas phase, were considered in this model. The growth of dendrites and hydrogen gas pores was reproduced using a cellular automaton (CA) approach. The diffusion of solute and hydrogen was calculated using the finite difference method (FDM). Columnar and equiaxed dendrite growth with porosity evolution were simulated. Competitive growth between different dendrites and porosities was observed. Dendrite morphology was influenced by porosity formation near dendrites. After solidification, when the porosities were surrounded by dendrites, they could not escape from the liquid, and they made pores that existed in the welded joints. With the increase in the cooling rate, the average diameter of porosities decreased, and the average number of porosities increased. The average diameter of porosities and the number of porosities in the simulation results had the same trend as the experimental results.

     

A Developed Method for Fabricating <Emphasis Type="Italic">In-Situ</Emphasis> TiC<Subscript><Emphasis Type="Italic">p</Emphasis></Subscript>/Mg Composites by Using Quick Preheating Treatment and Ultrasonic Vibration

Quick preheating treatment of the Al-Ti-C pellets and high-intensity ultrasonic vibration are introduced in the fabrication of in-situ TiC _p /Mg composites. Al-Ti-C pellets are preheated for about 130 seconds in the furnace at 1023 K (750 °C), in which magnesium is melted as well. In this process, plenty of heat can be accumulated due to the reactive diffusion between liquid aluminum and solid titanium in Al-Ti-C, and a small amount of Al₃Ti phase is formed as well. After adding the preheated Al-Ti-C into the molten magnesium, thermal explosion takes place in a few seconds. In the meantime, high-intensity ultrasonic vibration is applied into the melt to disperse in-situ formed TiC particles into the matrix and degas the melt as well. Microstructural characterization indicates that in-situ formed TiC particles are spherical in morphology and smaller than 2 μm in size. Furthermore, a homogeneous microstructure with low porosity of the magnesium composite is obtained due to the effect of ultrasonic vibration. A novel approach using the quick preheating treatment technique and high-intensity ultrasonic vibration to synthesize in-situ TiC _p /Mg composites is proposed in our research.     

Solidification Microstructure and Mechanical Properties of Cast Magnesium-Aluminum-Tin Alloys

The solidification microstructure and mechanical properties of as-cast Mg-Al-Sn alloys have been investigated using computational thermodynamics and experiments. The as-cast microstructure of Mg-Al-Sn alloys consists of α-Mg, Mg₁₇Al₁₂, and Mg₂Sn phases. The amount of Mg₁₇Al₁₂ and Mg₂Sn phases formed increases with increasing Al and Sn content and shows good agreement between the experimental results and the Scheil solidification calculations. Generally, the yield strength of as-cast alloys increases with Al and Sn content, whereas the ductility decreases. This study has confirmed an early development of Mg-7Al-2Sn alloy for structural applications and has led to a promising new Mg-7Al-5Sn alloy with significantly improved strength and ductility comparable with commercial AZ91 alloy.     

Processing,microstructure, and mechanical properties of cast <Emphasis Type="Italic">in-Situ</Emphasis> Al(Mg,Mn)-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>(MnO<Subscript>2</Subscript>) composite

Cast particulate composites, containing in-situ generated reinforcing particles of alumina, have been developed by solidification of slurry obtained by dispersion of externally added manganese dioxide particles (MnO₂) in molten aluminum, and alumina is formed by reaction of manganese dioxide with molten aluminum. The chemical reaction also releases manganese into molten aluminum. Magnesium is added to the melt in order to help wetting of alumina particles by molten aluminum and to retain the particles inside the melt. The present work aims to understand the influence of key parameters such as processing temperature, time, and the amount of MnO₂ particles added on the microstructure and mechanical properties of the resulting cast in-situ composites. The sequence of addition of MnO₂ particles and magnesium has significant influence on the microstructure and mechanical properties. Increasing processing temperature and time increases the extent of reduction of MnO₂ particles, generating more alumina particles as well as releasing more manganese to the matrix alloy. Alumina helps to nucleate finer and sometimes blocky MnAl₆ in the matrix of the composite and thereby results in relatively higher ductility and increased strength in the composite as compared to the base alloy of similar composition. Even in the presence of relatively higher porosity of 8 to 9 vol pct, one observes a percent elongation not below 7 to 8 pct, which is considerably higher than those observed in cast Al(Mg)-Al₂O₃ composite synthesized by externally added alumina particles.     

TiAl合金中的TiB2相生长形态及其对力学性能的影响

研究了B含量分别为0.2％和1.0％(原子分数)两种TiAl合金中TiB2相的生长机制,结果表明G2(Ti-47.5Al-5( Cr,Nb,W,Si)+1.0B％)合金中少量TiB2相是由于成分起伏从液相中生成的初生块状TiB2相,大部分TiB2相是在凝固过程与β相共同耦合生长的次生带状、杆状TiB2相;G1( Ti-47.5Al-5( Cr,Nb,W,Si)+0.2B％)合金中TiB2相是由共晶反应生成的次生带状TiB2相.G2合金全片层组织和网篮组织室温塑性均优于G1合金,网篮组织室温强度与Gt合金相当,而全片层组织室温强度却不如G1合金.在760 ℃/100 MPa/200 h蠕变条件下G2合金全片层组织残余蠕变量和蠕变速率均低于G1合金.     

Nonequilibrium solidification of undercooled melt of Ag-Cu alloy entrained in the primary phase

The solidification structure of undercooled melt of Ag-Cu alloy, entrained in its primary Cu-rich phase, has been investigated. The undercooling procedure consisted of equilibration of a Cu-13 pct Ag alloy in the two-phase liquid-solid region, followed by repeated thermal cycling of the liquid. Slow cooling of the sample in the present work established the ability to undercool the melt up to 70 K below the eutectic temperature of this alloy. The microstructure of the undercooled alloy indicated a complete absence of eutectic reaction on subsequent quenching of the melt directly from the equilibration temperature. The compositional analysis of the constituent phases by electron probe microanalysis (EPMA) technique provided evidence for the massive diffusionless solidification of the undercooled liquid. The X-ray diffraction study and electron microscopic examination indicated evidence for the spinodal transformation of the metastable solid solution phase. The composition of the phases formed on decomposition matched well with the calculated coherent spinodal boundaries in this system. The evolution of the metastable microstructure in the mushy-state quenching process of this alloy is discussed.     

Functionally Graded Al Alloy Matrix <Emphasis Type="Italic">In-Situ</Emphasis> Composites

In the present work, functionally graded (FG) aluminum alloy matrix in-situ composites (FG-AMCs) with TiB₂ and TiC reinforcements were synthesized using the horizontal centrifugal casting process. A commercial Al-Si alloy (A356) and an Al-Cu alloy were used as matrices in the present study. The material parameters (such as matrix and reinforcement type) and process parameters (such as mold temperature, mold speed, and melt stirring) were found to influence the gradient in the FG-AMCs. Detailed microstructural analysis of the composites in different processing conditions revealed that the gradients in the reinforcement modify the microstructure and hardness of the Al alloy. The segregated in-situ formed TiB₂ and TiC particles change the morphology of Si particles during the solidification of Al-Si alloy. A maximum of 20 vol pct of reinforcement at the surface was achieved by this process in the Al-4Cu-TiB₂ system. The stirring of the melt before pouring causes the reinforcement particles to segregate at the periphery of the casting, while in the absence of such stirring, the particles are segregated at the interior of the casting.     

Phase evolution during laser <Emphasis Type="Italic">in-situ</Emphasis> carbide coating

With the help of laser surface engineering, in-situ carbide composite coating on the surface of plain carbon steel was achieved. Energy dispersive spectroscopy (EDS) in supplement with X-ray diffractometry indicated the evolution of TiC, Fe-Cr, and M₇C₃ as major phases in the coating. A variation in the evolution of M₇C₃ phase was observed with respect to the laser power over the range of 900 to 2100 W (3 mm ×600 μm rectangular beam spot) during processing. Computational techniques were employed with the aim of studying possible reasons for phase evolution, stability of phases, solidification path, and optimization of parameters to stabilize the M₇C₃ phase and hence tailor properties.     

<Emphasis Type="Italic">In-Situ</Emphasis> Analysis of Coarsening during Directional Solidification Experiments in High-Solute Aluminum Alloys

Coarsening within the mushy zone during continuous directional solidification experiments was studied on an Al-30 wt pct Cu alloy. High brilliance synchrotron X-radiation microscopy allowed images to be taken in-situ during solidification. Transient conditions were present during directional solidification. Under these conditions, solute-rich settling liquid flow affects the dendritic array and thus coarsening. Coarsening was studied by following the secondary dendrite arm spacing (SDAS) of a developing dendrite at different local solidification times according to the mush depth and instant interface velocity. Solute enrichment and liquid flow cause deceleration and acceleration of the solidification front, which in turn influences both the mush depth and local growth and coarsening due to variations in solutal gradients and thus local undercooling. In addition, spacing between neighboring dendrites (i.e., primary dendrite arm spacing), which determines permeability within the mushy zone, affects the development of high-order branches. This article is based on a presentation given at the International Symposium on Liquid Metal Processing and Casting (LMPC 2007), which occurred in September 2007 in Nancy, France.     

Analysis of heat flow and microstructure evolution during spray deposition of Fe-3C-1.5Mn alloy

A theoretical model for the concomitant solidification of droplets and preform during spray deposition has been proposed, based on heat-flow analysis. It has been unambiguously demonstrated that cooling rates approaching those in the rapid solidification (RS) regime can only be achieved when the droplets are still in free flight during the deposition process. The cooling rates in the droplets range from 10⁴–10⁶ Ks^?1 depending upon their size for the experimental conditions employed in the present studies. In contrast, the model predicted cooling rates for the deposits in the region of 10³–10⁴ Ks^?1. A hypoeutectic Fe-3C-1.5Mn-0.3Si has been chosen as an experimental alloy for studies relating to microstructural characterization. The microstructure of powder developed fully during solidification of droplets in free flight revealed dendritic morphology of the metastable austenitic phase, whereas the spray-deposited alloy exhibited characteristic homogeneous and refined substructure. The evolution of microstructure during spray deposition as also during atomization has been compared and discussed by invoking the proposed model.     

Phase evolution during laser <Emphasis Type="Italic">In-Situ</Emphasis> carbide coating

With the help of laser surface engineering, in-situ carbide composite coating on the surface of plain carbon steel was achieved. Energy dispersive spectroscopy (EDS) in supplement with X-ray diffractometry indicated the evolution of TiC, Fe−Cr, and M₇C₃ as major phases in the coating. A variation in the evolution of M₇C₃ phase was observed with respect to the laser power over the range of 900 to 2100 W (3 mm×600 μm rectangular beam spot) during processing. Computational techniques were employed with the aim of studying possible reasons for phase evolution, stability of phases, solidification path, and optimization of parameters to stabilize the M₇C₃ phase and hence tailor properties.