共查询到20条相似文献,搜索用时 125 毫秒
1.
长期以来,在机床上加工较高精度轴类零件时,由于刀具磨损和机床热变形等原因,工件直径尺寸需要经常测量,并需经常调整刀具位置。这样不但影响生产效率,而且还难以保证直径的质量要求。为此,我们试制成功了一种气液联动弹性刀架补偿装置,它是与测量装置、控制装置组成轴类零件加工时的尺寸控制系统。通过大量试验证实,采用该系统可以在不停车的情况下实现对零件径向尺寸的自动测量和刀具位置的自动调整,既保证了高的加工精度,又能提高生产率。应用同样原理,也可用于镗孔时控制孔径尺寸精度。一、尺寸控制系统的组成与补偿装置工作原理尺寸控制系统由测量装置、控制装置及补偿(即自动调整)装置三部分组成(图1)。测量装置采用薄膜式气动量仪;控制装置主要由程序控制器及电流分配 相似文献
2.
3.
4.
5.
介绍一套用于汽车前照灯照明光度分布的测量装置。对该测量装置的测量原理、系统组成、软件设计及影响测量精度的因素等进行了讨论 ,并给出该系统的使用效果。 相似文献
6.
7.
8.
9.
10.
本文详细地叙述了系统的组成、工作原理和功能。温度、流量检测采用自行设计的采集装置,成本低,安装简便,可靠性高,满足了测量要求。采用该监测系统可实时地监测高炉冷却系统的水温差、流量及热负荷,为高炉安全生产提供依据。 相似文献
11.
郑海明 《仪表技术与传感器》2006,(10):52-53
国内火电厂安装的烟气在线监测系统在实际使用中运行状况不佳。调查发现监测结果不准确主要是由于采样问题造成的,减少烟气采样对测量结果产生的影响是烟气排放监测的技术难点之一。针对国内火电厂CEMS采样探针的一些缺点,设计了基于差分吸收光谱技术的新型采样监测探针,简化了整个采样子系统,提高运行的可靠性。 相似文献
12.
星载微波组件的热设计与试验研究 总被引:1,自引:0,他引:1
星载微波组件是决定星载雷达系统性能的最重要、最复杂和最吊贵的子系统,文中介绍星载微波组件热设计的重要性及特点,通过研究接触导热和辐射散热两种热传导形式,提出了相应的结构设计的基本途径来提高组件的散热效果。文中还介绍了热真空试验的重要性以及它的目的和试验步骤。热真空试验为星载微波组件的工程设计和优化航天产品提供了一条重要参考依据。 相似文献
13.
14.
15.
16.
基于GSM/GPRS的海上导航灯器远程监测系统 总被引:9,自引:0,他引:9
给出了基于GSM/GPRS的海上导航灯标信息的远程监测系统设计方案。系统主要由海上导航灯标现场检测子系统和陆上信息中转子系统两部分组成。考虑到系统的通用性,信息中转子系统还设计了标准的MODBUS协议,可以很容易地和任何装有MODBUS协议的监管设备进行通讯。现场检测子系统和信息中转子系统之间以GSM短信方式实现信息和指令交换,信息中转子系统和监管设备之间以标准的MODBUS协议进行通讯。监管设备一方面可对任一导航灯标进行设置,另一方面也可通过现场检测子系统的“定时发送”和“遇变则报”两种方式实现对多个导航灯标的信息进行轮回和实时的检测。在通讯方面,重点介绍了基于GSM的通讯协议设计方法。经现场调试运行,证明了方案的可行性。 相似文献
17.
Radiopharmaceuticals used in nuclear medicine for therapy or diagnosis (molecular imaging, PETscan, scintigraphy) are characterized in terms of volume activity before injection to patients. The current measurement process relies on dose calibrators which have to be calibrated by transfer standards, traceable to primary standards. For very short half-life radionuclides (few minutes), the metrological traceability can only be assured through an on-site calibration with primary standards. However, until now, there is no primary system for the direct measurement of such high activity radioactive solutions. This study presents the sub-system under development for the measurement of a sampled volume of the order of 1 μL with an associated relative target standard uncertainty of 1%. The volume of solution is a key parameter in activity per unit of volume calibration of radiopharmaceuticals solutions. This article focuses on the volume measurement method development and its validation by comparison to the gravimetric method.The paper, in a first part, describes the developed method and the associated hardware and software. The authors have chosen a non-contact optical method implemented by a microscope camera and associated optics in front of a transparent capillary.The second part of the paper describes the measurement process. Several image processing steps are described and the traceability to dimensional units is presented.Finally, the paper presents some validation results by comparison to a gravimetric measurement, including repeatability and accuracy tests. Further development and improvements, necessary for the finalization of the prototype and the measurement of nano-flow rates are discussed. 相似文献
18.
19.
以模块化设计和参数化设计为指导思想,以VisualBasic为编程语言和开发工具,对AutoCAD软件进行二次开发,研制出了界面友好的齿轮传动计算机辅助设计系统。该系统包括齿轮传动设计系统和绘图系统两个子系统,分别实现齿轮设计和绘图自动化。 相似文献