Effect of ionomer on clay dispersions in polypropylene‐layered silicate nanocomposites

In this study, polypropylene (PP)/clay nanocomposites containing different concentrations of ethylene‐methacrylic acid ionomer (i.e. Surlyn®) were prepared, and the effect of ionomer on clay dispersion was studied via WAXD, rheology, SEM, and TEM. The role of the ionomer in the nanocomposites was compared with that of maleic anhydride grafted PP (PP‐g‐MA), which has been widely used as a compatibilizer in making PP/clay nanocomposites. With an increase in the concentration of compatibilizer, the position of d₀₀₁ peak of OMMT shifted toward a lower angle for PP‐g‐MA system, while the position remained almost unchanged for Surlyn system, in which a larger interlayer spacing (d₀₀₁) was found with respect to the former. In rheology, the addition of the ionomer led to a gradual increase in both moduli and complex viscosity, and the nonterminal behavior at low frequency was observed in both systems. In addition, the ternary hybrid containing 20 wt % Surlyn achieved the largest enhancement in relative viscosity, which was more than that of the nanocomposite prepared from pure Surlyn or pure PP, presumably indicative of the existence of strong interaction between the components. Finally, SEM and TEM micrographs demonstrated that exfoliated structure was preferred for PP/Surlyn/OMMT hybrids, while intercalated morphology for PP/PP‐g‐MA/OMMT. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4024–4034, 2007     

Morphological evolution and mechanical property enhancement of natural rubber/polypropylene blend through compatibilization by nanoclay

Nanocomposites of natural rubber (NR)/polypropylene (PP) (80/20 wt %) blends filled with 5 phr pristine clay were prepared by melt‐mixing process. Effects of clay incorporation technique via conventional melt‐mixing (CV) and masterbatch mixing (MB) methods on nanostructure and properties of the blend nanocomposites were investigated. The XRD, SAXS, WAXD, and TEM results showed that the clays in the NR/PP blend nanocomposites were presented in different states of dispersion and were locally existed at the interface between NR and PP as well as dispersed in the NR matrix. The presence of clay caused unique morphological evolution such as fine fibrillar PP domains. The tensile strength was improved over the unfilled NR/PP blends by 53% and 224%, and the storage modulus at 25 °C was increased by 78% and 120% for the NR/PP/clay nanocomposites prepared by CV and MB methods, respectively. Significant improvement in both properties was particularly obtained from the MB method due to finer dispersion fibrillar PP phase in the NR matrix and stronger interfacial adhesion between NR and PP fibers, as suggested from DMA. The oil resistance of blend nanocomposites was also improved over that of the unfilled NR/PP blend, and this property was further progressed by the masterbatch mixing method. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44574.     

PP/clay nanocomposites: Effect of clay treatment on morphology and dynamic mechanical properties

The morphology and properties of polypropylene (PP)/clay nanocomposites are described. The melt intercalation of organophilic clay was carried out with a single‐screw extruder. The effects of two kinds of treatments of clay are discussed. Maleic anhydride (MAH)‐grafted PP was used as a compatibilizer. The expansion of the intergallery distance of the clay was governed by the interaction between the clay treatment and the compatibilizer. In one case, the composites exhibited significantly reduced intensities of diffraction peaks, suggesting partial exfoliation of the clay layers, whereas for the second clay sample, expansion of the gallery height was noted. The mechanical properties of the PP/clay composites showed significant enhancement in their mechanical and thermal properties. About a 35% increase in the tensile modulus and about a 10% increase in the tensile strength were observed. The thermal degradation temperature increased from 270 to about 400°C as a result of the incorporation of clay, and the extent depended on the dispersion of clay in the composite. The most interesting outcome of this study was the changes in morphology for PP/clay composites, which are reported here for the first time. An optical microscopic study revealed that the PP/clay composites could be crystallized at higher temperatures than pure PP and that the morphology was remarkably altered because of the presence of layers of clay. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1786–1792, 2001     

Influence of organically modified nanoclay on the performance of pineapple leaf fiber‐reinforced polypropylene nanocomposites

Polypropylene/Pine apple leaf fiber (PP/PALF)‐reinforced nanocomposites were fabricated using melt blending technique in a twin‐screw extruder (Haake Rheocord 9000). Variation in mechanical properties, crystallization behavior, water absorption, and thermal stability with the addition of nanoclay in PP/PALF composites were investigated. It was observed that the tensile, flexural, and impact properties of PP increase with the increase in fiber loading from 10 to 30 wt %. Composites prepared using 30 wt % PALF and 5 wt % MA‐g‐PP exhibited optimum mechanical performance with an increase in tensile strength to 31%, flexural strength to 45% when compared with virgin PP. Addition of nanoclay results in a further increase in tensile and flexural strength of PP/PALF composites to 20 and 24.3%, which shows intercalated morphology. However, addition of nanoclay does not show any substantial increase in impact strength when compared with PP/PALF composites. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), confirming a strong influence between the fiber/nanoclay and MA‐g‐PP. Differential scanning calorimetry, thermogravimetric analysis thermograms also showed improved thermal properties when compared with the virgin matrix. TEM micrographs also showed few layers of agglomerated clay galleries along with mixed nanomorphology in the nanocomposites. Wide angle X‐ray diffraction studies indicated an increase in d‐spacing from 22.4 Å in Cloisite 20A to 40.1 Å in PP/PALF nanocomposite because of improved intercalated morphology. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polypropylene‐organoclay nanocomposite: Preparation,microstructure, and mechanical properties

A series of polypropylene (PP) nanocomposites containing 2, 4, and 6 wt % of an organophilic montmorillonite clay was prepared via direct melt mixing in the presence of maleic anhydride grafted polypropylene (PP‐g‐MAH) as compatibilizing agent. Microstructure characterization was performed by X‐ray diffraction analysis. Nanocomposites exhibited a 15 and 22% enhancement in tensile modulus and impact strength, respectively. The heat deflection temperature of PP nanocomposites was 36°C greater than for pure PP. Thermal and mechanical properties of nanocomposites were compared to properties of traditional PP‐talc and PP‐glass fiber composites. The results showed that the properties of nanocomposites improved compared to ordinary polypropylene composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology,deformation behavior and thermomechanical properties of polypropylene/maleic anhydride grafted polypropylene/layered silicate nanocomposites

Nanocomposites polypropylene (PP) with 3 and 7 wt % of clay were prepared by melt mixing. Four types of maleic anhydride grafted PP (MAPP) in broad range of MA groups content (0.3–4 wt %) and molecular weights (MW) were used as polar compatibilizers. The effect of the MAPP kind on both the clay dispersion and miscibility with PP was studied. The mixed intercalated/exfoliated morphologies of nanocomposites in the presence of all studied compatibilizers were revealed by XRD and TEM. The oligomer compatibilizer with 4 wt % of MA groups increases the intercalation ability of polymer into clay galleries but this one has limited miscibility with PP and worsens crystalline structure of polymer matrix. The MAPPs with 0.3–1.3% of MA are characterized by the lower intercalation ability but well cocrystallize with PP. Maximum reinforcing effect is attained using high MW MAPP with 0.6% MA and for nanocomposite with 7 wt % (3.8 vol %) of clay it averages almost 1.7 times relative to neat PP and 1.3 times relative to noncompatibilized composite. Dynamic storage moduli of nanocomposites compatibilized by MAPPs with 0.3–1.3% of MA containing 7 wt % of clay increase up to 1.4–1.5 around 30–75°C and over the whole temperature range remain higher compared with both neat PP and uncompatibilized composite. On the contrary, the oligomer MAPP with 4 wt % of MA groups decreases the thermal–mechanical stability of nanocomposite at high temperature compared with both PP and uncompatibilized composites. The study of nanocomposites flammability showed that creating complex composites containing both layered silicate and relatively small amount of magnesium hydroxide can be a successful approach to reduce the combustibility of PP‐based nanocomposites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Supercritical carbon dioxide (scCO2) dispersion of poly(ethylene terephthalate)/clay nanocomposites: Structural,mechanical, thermal,and barrier properties

Dispersed poly(ethylene terephthalate) (PET)/clay nanocomposites can lead to materials with superior barrier and mechanical properties. PET/clay nanocomposites were prepared by melting extrusion of PET with as‐received or supercritical carbon dioxide (scCO₂) predispersed Cloisite^® 30B (30B). The predispersion of 30B was assessed by WAXD, SEM, and TGA, and results indicated that scCO₂ processing could predisperse 30B and the surface modification of the clay was preserved after processing. The structure of PET/30B nanocomposites was investigated by WAXD and TEM confirming that PET has penetrated into the clays inter‐galleries and the predispersed clays lead to improved interfacial interaction and homogenous clay dispersion. Both tensile strength and Young's modulus were improved by 12.1% and 24.9% respectively, as incorporating of 3 wt % of scCO₂ processed clay. Differential scanning calorimetry (DSC) results indicated that clay particles served as nucleation agent could increase the crystallinity whereas had no impact on melting process. In addition, with the addition of 1 wt % of predispersed clay, a significant reduction of oxygen permeation (～33%) was achieved at 23 °C and the maximum reduction (44%) was achieved by adding 3 wt % processed clay. Moreover, we confirmed the effect of temperature on the permeation of PET/30B nanocomposites depended both on the Arrhenius behavior of the organic phases and tortuous path effects, where improved clay dispersion resulted in a higher effective activation energy. Moreover, the transparency of PET matrix was preserved for all nanocomposites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44779.     

Preparation and characterization of polyethylene–clay nanocomposites by using chlorosilane‐modified clay

Clay was modified by trimethylchlorosilane; after modification, hydroxyl groups at the edge of layers were reacted and CEC value was drastically decreased. Polyethylene–clay composites were prepared by melt compounding. Wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) showed that intercalated nanocomposites were formed using organoclay ion‐exchanged from chlorosilane‐modified clay, but conventional composites formed using organoclay directly ion‐exchanged from crude clay. Dynamic mechanical analysis (DMA) of PE and PE–clay composites was conducted; the results demonstrated that nanocomposites were more effective than conventional composites in reinforcement and addition of organoclay resulted in the increase of glass transition temperature (T_g), but crude clay had no effect on T_g of PE–clay composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 676–680, 2004     

Mechanical properties of polypropylene/clay nanocomposites: Effect of clay content,polymer/clay compatibility,and processing conditions

In this work, polypropylene/clay nanocomposites with 0.5, 1, 3, and 5 wt % of montmorillonite (MMT) (unmodified clay) were prepared by intensive mixing at 50 rpm and 10 min of mixing. For the highest clay content (5 wt %), the initial materials or the processing conditions were changed to study their independent effect. On one hand, 10 wt % of PP‐graft‐MA (PP‐g‐MA) was incorporated or MMT was replaced by organomodified clays (C10A and C30B). On the other side, for the initial system, the speed of rotation (100 and 150 rpm) and the mixing time (5 and 15 min) were altered. In all cases, the state of the clay inside the matrix (DRX), the degree of dispersion in the micro (SEM) and nano (TEM) scales, and the rheological and mechanical properties were analyzed. It was found that the stiffness increased with clay content, whereas tensile and impact strength did not significantly change. Although intercalated structures were observed in the composites with unmodified clay, in the composites with modified clay or PP‐g‐MA, improved dispersion of clay in PP was found. The mechanical properties increased accordingly. The degree of dispersion of the filler in the matrix appeared to be unaffected by the changes in the processing conditions introduced. Finally, the elastic modulus was modeled by using an effective filler‐parameter model based on Halpin–Tsai equations, which also allowed estimating the relative degree of dispersion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polypropylene/clay nanocomposites prepared by in situ grafting‐melt intercalation with a novel cointercalating monomer

Polypropylene (PP)/clay nanocomposites were prepared by melt‐compounding PP with organomontmorillonite (OMT), using maleic anhydride grafted polypropylene (PP‐g‐MA) as the primary compatibilizer and N‐imidazol‐O‐(bicyclo pentaerythritol phosphate)‐O‐(ethyl methacrylate) phosphate (PEBI) as the cointercalating monomer. X‐ray diffraction patterns indicated that the larger interlayer spacing of OMT in PP was obtained due to the cointercalation monomer having a large steric volume and the d‐spacing further increased with the addition of PP‐g‐MA, as evidenced by transmission electron microscopy. Thermogravimetric analysis revealed that the PEBI‐containing PP nanocomposites exhibited better thermal stability than PEBI‐free PP composites. Dynamic mechanical analysis demonstrated that the storage modulus was significantly enhanced, and the glass transition temperature (T_g) shifted slightly to low temperature with the incorporation of clay for PP/OMT hybrids. PEBI‐containing PP/OMT composites gave a lower T_g value because of the strong internal plasticization effect of PEBI in the system. Cone calorimetry showed that the flame‐retardancy properties of PP nanocomposites were highly improved with the incorporation of PEBI. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization,mechanical, and fracture behavior of mullite fiber‐reinforced polypropylene nanocomposites

This study describes the reinforcement effect of surface modified mullite fibers on the crystallization, thermal stability, and mechanical properties of polypropylene (PP). The nanocomposites were developed using polypropylene‐grafted‐maleic anhydride (PP‐g‐MA) as compatibilizer with different weight ratios (0.5, 1.0, 1.5, 2.5, 5.0, and 10.0 wt %) of amine functionalized mullite fibers (AMUF) via solution blending method. Chemical grafting of AMUF with PP‐g‐MA resulted in enhanced filler dispersion in the polymer as well as effective filler‐polymer interactions. The dispersion of nanofiller in the polymer matrix was identified using scanning electron microscopy (SEM) elemental mapping and transmission electron microscopy (TEM) analysis. AMUF increased the Young's modulus of PP in the nanocomposites up to a 5 wt % filler content, however, at 10 wt % loading, a decrease in the modulus resulted due to agglomeration of AMUF. The impact strength of PP increased simultaneously with the modulus as a function of AMUF content (up to 5 wt %). The mechanical properties of PP‐AMUF nanocomposites exhibited improved thermal performance as compared to pure PP matrix, thus, confirming the overall potential of the generated composites for a variety of structural applications. The mechanical properties of 5 wt % of AMUF filled PP nanocomposite were also compared with PP nanocomposites generated with unmodified MUF and the results confirmed superior mechanical properties on incorporation of modified filler. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43725.     

The preparation of nano-clay/polypropylene composite materials with improved properties using supercritical carbon dioxide and a sequential mixing technique

A semi-continuous process using scCO₂ is reported for processing polymer–clay composites with high clay loading (i.e. 10 wt %) by reducing the collapse of the exfoliated clays. Two major modifications are involved in the new procedure: exfoliating the nano-clay directly into the hopper filed with pellets followed by processing the composite immediately and sequentially mixing the clay into the melt. This latter approach helped to minimize the clay collapse when processing the composites with high clay loadings. Transmission electron microscopy (TEM) and wide angle X-ray diffraction (WAXD) results are provided to investigate the effect of sequential mixing on reducing the clay collapse in the nanocomposite. Surface modified montmorillonite (MMT) nano-clay/polypropylene (PP) composite at 10 wt % nano-clay with improved clay dispersion was obtained with increased modulus and tensile strength of 63 % and 16%, respectively, compared to the pure PP matrix.     

Comparative Characterization of PP Nano‐ and Microcomposites by In‐Mold Shrinkage Measurements and Structural Characteristics

Poly(propylene)‐clay nanocomposites and poly(propylene) containing conventional inorganic fillers such as calcium carbonate (CaCO₃) and glass fiber were used in a comparative study focusing on dimensional stability, structure, mechanical and thermal properties. Micro‐ and nanocomposites were prepared by melt blending in a twin‐screw extruder. The relative influence of each filler was observed from dimensional stability measurements and structural analysis by WAXD, TEM, and thermal and mechanical properties. At equal filler loadings, PP/clay nanocomposites exhibit an improvement in dimensional stability and were the only composites capable of reduced shrinkage in both in‐flow and cross‐flow directions. The flexural modulus of PP increased nearly 20% by compounding with 4% organoclay, as compared to a similar performance obtained by compounding with 10 wt.‐% of CaCO₃ or approximately 6 wt.‐% of glass fiber. The HDT and thermal stability of PP were enhanced by using nanoclay as filler.

     

Crystallization kinetics of polypropylene composites filled with nano calcium carbonate modified with maleic anhydride

The subject of this study was the crystallization behavior and thermal properties of polypropylene (PP)/maleic anhydride (MAH) modified nano calcium carbonate (nano‐CaCO₃) composites. In this study, 5 wt % nano‐CaCO₃ modified with different contents of MAH was filled into a PP matrix. X‐ray diffraction and differential scanning calorimetry were used to characterize the crystal morphology and crystallization kinetics of a series of composites. The results demonstrate that the nano‐CaCO₃ modified with MAH had an important effect on the thermal and morphological properties of the nanocomposites. The Avrami exponent of the pure PP was an integer, but those of the composites were not integers, but the crystallization rate constant decreased as the content of MAH in the nano‐CaCO₃ filler increased in isothermal crystallization. In nonisothermal crystallization, the kinetic parameter F(T) and the degree of crystallinity of pure PP were compared with those of the PP composites filled with nano‐CaCO₃. We suggest that heterogeneous nucleation existed in the PP composites and that the transformation and retention of the β‐form crystal into the α‐form crystal took place in the composite system and the β‐form crystal had a higher nucleation rate and growth process than the α‐form crystal in the PP composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The effect of clay type and of clay–masterbatch product in the preparation of polypropylene/clay nanocomposites

Clay containing polypropylene (PP) nanocomposites were prepared by direct melt mixing in a twin screw extruder using different types of organo‐modified montmorillonite (Cloisite 15 and Cloisite 20) and two masterbatch products, one based on pre‐exfoliated clays (Nanofil SE 3000) and another one based on clay–polyolefin resin (Nanomax‐PP). Maleic anhydride‐grafted polypropylene (PP‐g‐MA) was used as a coupling agent to improve the dispersability of organo‐modified clays. The effect of clay type and clay–masterbatch product on the clay exfoliation and nanocomposite properties was investigated. The effect of PP‐g‐MA concentration was also considered. Composite morphologies were characterized by X‐ray diffraction (XRD), field emission gun scanning electron microscopy (FEG‐SEM), and transmission electron microscopy (TEM). The degree of dispersion of organo‐modified clay increased with the PP‐g‐MA content. The thermal and mechanical properties were not affected by organo‐modified clay type, although the masterbatch products did have a significant influence on thermal and mechanical properties of nanocomposites. Intercalation/exfoliation was not achieved in the Nanofil SE 3000 composite. This masterbatch product has intercalants, whose initial decomposition temperature is lower than the processing temperature (T ～ 180°C), indicating that their stability decreased during the process. The Nanomax‐PP composite showed higher thermal and flexural properties than pure PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Phase morphology and clay distribution of poly(trimethylene terephthalate)/polypropylene/montmorillonite nanocomposites

Poly(trimethylene terephthalate) (PTT)/polypropylene (PP) blend nanocomposites were prepared by melt mixing of PTT, PP, and organically modified clay. The phase morphologies of the PTT/PP nanocomposites and the distribution of the clay in the nanocomposites were investigated using scanning electron microscopy, transmission electron microscopy (TEM), and wide angle X‐ray diffraction. When PP is the dispersed phase, the domain size of the PP phase is decreased significantly with increasing the clay content from 0 to 5 wt %. In contrast, when PTT is the dispersed phase, the dimension of the PTT phase is a little larger in the presence of 2 wt % clay compared with the case of without clay. TEM observations indicate that the clay is mainly distributed at the phase interfaces along the phase borderlines. In addition, some intercalated clay tactoids (multilayer particles) are observed in the PTT matrix whereas no discernable clay particles can be found in the PP phase, indicating that the affinity of clay with PTT is higher than with PP. In the presence of 5 wt % PP‐graft‐maleic anhydride, the phase morphology is much finer, and most clay is exfoliated and distributed at the phase interfaces forming phase borderlines in polygonal shape. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Use of purified and modified bentonites in linear low‐density polyethylene/organoclay/compatibilizer nanocomposites

Polyethylene‐based ternary nanocomposites were prepared with different clay structures, obtained by the modification of purified Resadiye bentonite as the reinforcement, a random terpolymer of ethylene, butyl acrylate, and maleic anhydride with the trade name Lotader3210 as the compatibilizer, and linear low‐density polyethylene (LLDPE) as the polymer matrix in an intensive batch mixer. The quaternary ammonium/phosphonium salts used for the modification of bentonite were dimethyldioctadecyl ammonium (DMDA) chloride (Cl), tetrakisdecyl ammonium (TKA) bromide (Br), and tributylhexadecyl phosphonium (TBHP) Br. The effects of the physical properties and structure of the organoclay on the clay dispersion were studied at different clay contents (2 and 5 wt %) and at a compatibilizer/organoclay ratio of 2.5. The extent of organoclay dispersion was determined by X‐ray diffraction (XRD) and was verified by transmission electron microscopy (TEM), mechanical testing, and rheological analysis. XRD analysis showed that the nanocomposite with the organoclay DMDA contained intercalated silicate layers, as also verified by TEM. The TEM analysis of the nanocomposites with TBHP exhibited intercalated/partially exfoliated clay dispersion. TKA, with a crowded alkyl environment, sheltered and hindered the intercalation of polymer chains through the silicate layers. In comparison to pure LLDPE, nanocomposites with a 33–41% higher Young's modulus, 16–9% higher tensile strength, and 75–144% higher elongation at break were produced with DMDA and TBHP, respectively (at 5 wt % organoclay). The storage modulus increased by 807–1393%, and the dynamic viscosity increased by 196–339% with respect to pure LLDPE at low frequencies for the samples with DMDA and TBHP (at 5 wt % organoclay). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Soundproofing properties of polypropylene/clay/carbon nanotube nanocomposites

In this article, polypropylene (PP)/clay/carbon nanotube (CNT) composites were prepared via a solution blending method. Sound transmission loss (STL), determined with an impedance tube, was used to characterize their soundproofing properties. The STL for the PP/4.8 wt % clay/0.5 wt % CNT composite was about 15–21 dB higher than that for pure PP at high frequencies (3200–6400 Hz) and about 8–14 dB higher at low frequencies (580–620 Hz). X‐ray diffraction (XRD) and transmission electron microscopy (TEM) were used to study the crystallinity and the microstructure. A synergistic effect on the STL was established between the structure of the homogeneous dispersion and strong interfacial adhesion. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Polypropylene/montmorillonite composites and their application in hybrid fiber preparation by melt‐spinning

Polypropylene (PP)/organomontmorillonite (OMMT) nanocomposites have been successfully prepared by melt intercalation by using the conventional method of twin‐screw extrusion and subsequently submitted for melt‐spinning. The structure and properties of the PP/clay nanocomposites and hybrid fibers were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and crystallization dynamics, etc. The organoclay layers were found to disperse in the PP resin at the nanometer level. The nanoscaled OMMT layers, dispersed in the PP matrix, actually played the role of heterogeneous nuclei species in the process of PP crystallization and increased the nucleation speed of the composites, hereby leading to the increase of crystallization rate of the as‐spun fiber. Meanwhile, it was found that the crystallinity of PP/OMMT hybrid fibers is much higher than that of pure PP fiber at the same draw ratios, whereas the orientation of PP/OMMT hybrid fibers is much lower than that of pure PP fiber at the same draw ratios. Because of the effective intercalation of OMMT into PP matrix, the nanocomposites have good spinnability, and the moisture absorption of the final PP fiber is improved. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 552–558, 2004