Mechanical relaxations of poly(β,L‐aspartate)s

The dynamic mechanical thermal properties of a family of poly(α‐alkyl β,L ‐aspartate)s bearing various cyclic, linear, and branched alkoxycarbonyl groups in the side chain were studied. The measurements carried out by dynamic mechanical thermal analysis (DMTA) revealed the significant influence of the constitution of the side chain on mechanical relaxation phenomena. Three relaxations were observed, which are referred to as γ, β, and α, in increasing order of temperature. The first two, γ and β, are related to the local and global motions of the side chain, respectively. Relaxation α is related to the motion of the main chain. Relaxation β, which is associated with the rotation of the side chain, is the most intense. The magnitude and temperature at which this relaxation occurs depends on the volume, the length, and the degree of branching of the ester group of the side chain. A comparison between the dynamic mechanical properties of poly(β,L ‐aspartate)s and poly(α,L ‐glutamate)s revealed that the two methylene groups spacing the ester group from the main chain provides the poly(α‐L ‐glutamate)s with greater mobility, and thus, relaxations α and β occur at lower temperatures. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 994–1003, 2006     

Miscibility,thermal behaviour,morphology and mechanical properties of binary blends of poly[(R)‐3‐hydroxybutyrate] with poly(γ‐benzyl‐L‐glutamate)+

The miscibility, thermal behaviour, morphology and mechanical properties of poly[(R)‐3‐hydroxybutyrate] (PHB) with poly(γ‐benzyl‐L ‐glutamate) (PBLG) are investigated by means of differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and tensile tests. The DSC results show that PHB and PBLG are immiscible in the melt state. Such immiscibility also exists in the amorphous state due to a clear two‐phase separated structure observed by SEM measurements. The blend samples with different thermal history, namely as original and melt samples separately, display differences in thermal behaviour such as the DSC scan profile, the crystallinity and the melting temperature of PHB. The crystallization of PHB both from the molten state and the amorphous state is retarded on addition of the second component. The SEM measurements reveal that a phase inversion occurs between the PHB/PBLG (60/40) and PHB/PBLG (40/60) blends. Except for the PHB/PBLG (40/60) blend, a microphase separated structure is observed for all blend compositions. The mechanical properties vary considerably with blend composition. Compared with pure components, the PHB/PBLG (20/80) blend shows a certain improvement in mechanical properties. © 2001 Society of Chemical Industry     

Synthesis and characterization of novel poly(γ‐benzyl‐L‐glutamate) derivatives tailored for the preparation of nanoparticles of pharmaceutical interest

Four poly(γ‐benzyl‐L ‐glutamate) (PBLG) derivatives bearing at one end specific groups were synthesized by ring‐opening polymerization of the corresponding γ‐benzyl‐L ‐glutamate N‐carboxyanhydride using different amine‐terminated initiators. These moieties were chosen to introduce, on demand, specific functionalities in nanoparticles of pharmaceutical interest. The PBLG and PBLG derivatives were characterized by ¹H NMR, viscosimetry, Fourier transform infrared spectroscopy and differential scanning calorimetry. Nanoparticles smaller than 100 nm in diameter could be easily prepared from these PBLG derivatives by slight modification of a known nanoprecipitation technique. Copyright © 2006 Society of Chemical Industry     

Influence of γ‐irradiation on poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) was γ‐irradiated (5–20 kGy) by a ¹³⁷Cs source at room temperature in air. The changes in the molecular structure attributed to γ‐irradiation were studied by mechanical testing (flexure and hardness), size‐exclusion chromatography, differential scanning calorimetry, thermal gravimetric analysis, and both Fourier transform infrared and solution ¹³C‐NMR spectroscopy. Scanning electron microscopy was used to investigate the influence of the dose of γ rays on the fracture behavior of PMMA. The experimental results confirm that the PMMA degradation process involves chain scission. It was also observed that PMMA presents a brittle fracture mechanism and modifications in the color, becoming yellowish. The mechanical property curves show a similar pattern when the γ‐radiation dose increases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 886–895, 2002     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Largely improved tensile extensibility of poly(L‐lactic acid) by adding poly(ε‐caprolactone)

Poly(L ‐lactic acid) (PLLA) has good biocompatibility, biodegradability and physical properties. However, one of the drawbacks of PLLA is its brittleness due to the stiff backbone chain. In this work, a largely improved tensile toughness (extensibility) of PLLA was achieved by blending it with poly(ε‐caprolactone) (PCL). To obtain a good dispersion of PCL in the PLLA matrix, blends were prepared via a solution‐coagulation method. An increase in extensibility of PLLA of more than 20 times was observed on adding only 10 wt% of PCL, accompanied by a slight decrease in tensile strength. However, annealing of the samples led to a sharp decrease of extensibility due to phase separation and a change of crystalline structure. To conserve the good mechanical properties of PLLA/PCL blends, the blends were crosslinked via addition of dicumyl peroxide during the preparation process. For the crosslinked blend films, the extensibility was maintained nearly at the original high value even after annealing. Morphological analysis of cryo‐fractured and etched‐smoothed surfaces of the PLLA/PCL blends was carried out using scanning electron microscopy. Differential scanning calorimetry and polarized light microscopy experiments were used to check the possible change of crystallinity, melting point and crystal morphology for both PLLA and PCL after annealing. The results indicated that the combination of solution‐coagulation and crosslinking resulted in a good and stable dispersion of PCL in the PLLA matrix, which is considered as the main reason for the observed improvement of tensile toughness. Copyright © 2010 Society of Chemical Industry     

Glass transition temperature of methyl methacrylate–ethyl α‐benzoyloxymethylacrylate copolymers

Poly(ethyl α‐benzoyloxymethylacrylate) (EBMA) and copolymers of methyl methacrylate (MMA) with EBMA have been prepared by free radical polymerization. Monomer precursors of ethyl α‐benzoyloxymethylacrylate have likewise been polymerized. Glass transition temperatures (T_g) of homo and copolymers have been determined by differential scanning calorimetry. The Johnston equation, which considers the influence of monomeric unit distribution on the copolymer glass transition temperature, has been used to explain the T_g behaviour. T_g12 has been calculated by the application of the Johnston equation, which gave a value markedly lower than the average value expected from the additive contribution of the T_g of the corresponding homopolymers. © 2000 Society of Chemical Industry     

Thermal decomposition behavior of γ‐irradiated poly(vinyl acetate)/poly(methyl methacrylate) miscible blends

Miscible polymer blends based on various ratios of poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) were prepared in film form by the solution casting technique using benzene as a common solvent. The thermal decomposition behavior of these blends and their individual homopolymers before and after γ‐irradiation at various doses (50–250 kGy) was investigated. The thermogravimetric analysis technique was utilized to determine the temperatures at which the maximum value of the rate of reaction (T_max) occurs and the kinetic parameters of the thermal decomposition. The rate of reaction curves of the individual homopolymers or their blends before or after γ‐ irradiation displayed similar trends in which the T_max corresponding to all polymers was found to exist in the same position but with different values. These findings and the visual observations of the blend solutions and the transparency of the films gave support to the complete miscibility of these blends. Three transitions were observed along the reaction rate versus temperature curves; the first was around 100–200°C with no defined T_max, which may arise from the evaporation of the solvent. The second T_max was in the 340–380°C range, which depended on the polymer blend and the γ‐irradiation condition. A third transition was seen in the rate of reaction curves only for pure PVAc and its blends with PMMA with ratios up to 50%, regardless of γ‐ irradiation. We concluded that γ‐irradiation improved the thermal stability of PVAc/PMMA blends, even though the PMMA polymer was degradable by γ irradiation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1773–1780, 2006     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Crystallization behavior of poly(ϵ‐caprolactone) in poly(ϵ‐caprolactone) and poly(vinyl methyl ether) mixtures

The morphological development and crystallization behavior of poly(?‐caprolactone) (PCL) in miscible mixtures of PCL and poly(vinyl methyl ether) (PVME) were investigated by optical microscopy as a function of the mixture composition and crystallization temperature. The results indicated that the degree of crystallinity of PCL was independent of the mixture composition upon melt crystallization because the glass‐transition temperatures of the mixtures were much lower than the crystallization temperature of PCL. The radii of the PCL spherulites increased linearly with time at crystallization temperatures ranging from 42 to 49°C. The isothermal growth rates of PCL spherulites decreased with the amount of the amorphous PVME components in the mixtures. Accounting for the miscibility of PCL/PVME mixtures, the radial growth rates of PCL spherulites were well described by a kinetic equation involving the Flory–Huggins interaction parameter and the free energy for the nuclei formation in such a way that the theoretical calculations were in good agreement with the experimental data. From the analysis of the equilibrium melting point depression, the interaction energy density of the PVME/PCL system was calculated to be ?3.95 J/cm³. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of p‐perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐methyl styrene)

p‐Perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐ methyl styrene) 3 was synthesized via electron transfer of perfluoro‐di{2‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}propionyl peroxide 2 and poly(α‐methyl styrene) 1 at different reactant molar ratios (2 : 1). The modified polymer 3 was characterized by various techniques. The ring p‐substitution was proved by FTIR and ¹⁹FNMR. The desulfonation appeared at above 124°C was found by TGA. The molecular weight determined by GPC increased with the increase of reactant molar ratio, and the polydispersity values indicated there was no degradation of the parent polymer chain in the reaction. Followed by hydrolysis and acidification, the modified polymer 3 could be further quantitatively converted into its sulfonic form 4. Ion exchange capacity of novel polyelectrolyte 4 can be controlled by changing reactant molar ratio (2 : 1). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3615–3618, 2006     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Porous biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): physical properties,morphology, and biodegradation

Poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their films without or blended with 50 wt% poly(ethylene glycol) (PEG) were prepared by solution casting. Porous films were obtained by water‐extraction of PEG from solution‐cast phase‐separated PLLA‐blend‐PCL‐blend‐PEG films. The effects of PLLA/PCL ratio on the morphology of the porous films and the effects of PLLA/PCL ratio and pores on the physical properties and biodegradability of the films were investigated. The pore size of the blend films decreased with increasing PLLA/PCL ratio. Polymer blending and pore formation gave biodegradable PLLA‐blend‐PCL materials with a wide variety of tensile properties with Young's modulus in the range of 0.07–1.4 GPa and elongation at break in the range 3–380%. Pore formation markedly increased the PLLA crystallinity of porous films, except for low PLLA/PCL ratio. Polymer blending as well as pore formation enhanced the enzymatic degradation of biodegradable polyester blends. Copyright © 2006 Society of Chemical Industry     

Electrospun poly(L‐lactide)/poly(ε‐caprolactone) blend fibers and their cellular response to adipose‐derived stem cells

Polymer blending is one of the most effective methods for providing new, desirable biocomposites for tissue‐engineering applications. In this study, electrospun poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) blend fibrous membranes with defect‐free morphology and uniform diameter were optimally prepared by a 1 : 1 ratio of PLLA/PCL blend under a solution concentration of 10 wt %, an applied voltage of 20 kV, and a tip‐to‐collector distance of 15 cm. The fibrous membranes also showed a porous structure and high ductility. Because of the rapid solidification of polymer solution during electrospinning, the crystallinity of electrospun PLLA/PCL blend fibers was much lower than that of the PLLA/PCL blend cast film. To obtain an initial understanding of biocompatibility, adipose‐derived stem cells (ADSCs) were used as seed cells to assess the cellular response, including morphology, proliferation, viability, attachment, and multilineage differentiation on the PLLA/PCL blend fibrous scaffold. Because of the good biocompatibility and nontoxic effect on ADSCs, the PLLA/PCL blend electrospun fibrous membrane provided a high‐performance scaffold for feasible application in tissue engineering using ADSCs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Swelling behaviour of poly(α‐hydroxyacrylic acid) gel

Poly(α‐hydroxy acrylic acid) (PHA) and poly(acrylicacid) (PAA) gels were prepared by irradiating the respective 15 wt% aqueous solutions with γ‐rays. Swelling ratios for PHA gel were measured as a function of pH and divalent cation (Mg²⁺, Ca²⁺, Mn²⁺, Co²⁺, Ni²⁺, Cu²⁺) concentration C₂ in the external solution to provide a comparison with the results for PAA gels. It was found that the swelling ratio of PHA gel steeply increases between pH 2 and 4, followed by a gradual swelling in the higher pH region. The corresponding steep swelling of PAA gel was observed at pH 3–6. Cation specificity in the equilibrium swelling ratio at a lower C₂ value (1.0 × 10⁻³ M) was approximately consistent with the binding selectivity in the solution system. Typically, the swelling ratio of PHA gel in the presence of Ca²⁺ was significantly lower than in the Mg²⁺ system, while the difference was slight for PAA gel. The response of the swelling ratio to changes in pH and C₂ was analysed as a first order relaxation to estimate the time constants. The (de)swelling kinetics measured by both the pH and C₂ jump were qualitatively interpreted in terms of main‐chain stiffness and intermolecular hydrogen bonding in the respective polymers. © 2000 Society of Chemical Industry     

Miscibility of block copolymers of poly(ε‐caprolactone) and poly(ethylene glycol) with poly(3‐hydroxybutyrate) as well as the compatibilizing effect of these copolymers in blends of poly(ε‐caprolactone) and poly(3‐hydroxybutyrate)

Atactic poly(3‐hydroxybutyrate) (a‐PHB) and block copolymers of poly(ethylene glycol) (PEG) with poly(ε‐caprolactone) (PCL‐b‐PEG) were synthesized through anionic polymerization and coordination polymerization, respectively. As demonstrated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) measurements, both chemosynthesized a‐PHB and biosynthesized isotactic PHB (i‐PHB) are miscible with the PEG segment phase of PCL‐b‐PEGs. However, there is no evidence showing miscibility between both PHBs and the PCL segment phase of the copolymer even though PCL has been block‐copolymerized with PEG. Based on these results, PCL‐b‐PEG was added, as a compatibilizer, to both the PCL/a‐PHB blends and the PCL i‐PHB blends. The blend films were obtained through the evaporation of chloroform solutions of mixed components. Excitingly, the improvement in mechanical properties of PCL/PHB blends was achieved as anticipated initially upon the addition of PCL‐b‐PEG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2600–2608, 2001     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) during storage at room temperature

Copolymer of L ‐lactide and ε‐caprolactone [P(LLA‐CL)] (50/50) was synthesized using stannous octoate and was stored at room temperature. The change in physical properties occurring during this storage at room temperature was investigated by differential scanning calorimetry (DSC), X‐ray diffractometry, polarizing optical microscopy, tensile and bending tests, and light absorbance measurements. It was concluded that the increase in mechanical properties and light absorbance during storage can be ascribed to gradual selective crystallization of the L ‐lactide sequence in P(LLA‐CL) at room temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 947–953, 2000     

Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007