Synthesis and properties of silver nanoparticles in chitosan‐based thermosensitive semi‐interpenetrating hydrogels

In this article, thermosensitive poly(N‐isopropyl acrylamide‐co‐vinyl pyrrolidone)/chitosan [P(NIPAM‐co‐NVP)/CS] semi‐interpenetrating (semi‐IPN) hydrogels were prepared by redox‐polymerization using N,N‐methylenebisacrylamide as crosslinker and ammonium persulfate/N,N,N′,N′‐tetramethylethylenediamine as initiator. Highly stable and uniformly distributed Ag nanoparticles were prepared by using the semihydrogel networks as templates via in situ reduction of silver nitrate in the presence of sodium borohydride as a reducing agent. Introduction of CS improves the hydrogels swelling ratio (SR) and stabilizes the formed Ag nanoparticles in networks. Scanning electron microscopy and transmission electron microscopy revealed that Ag nanoparticles were well dispersed with diameters of 10 nm. The semi‐IPN hydrogel/Ag composites had higher SR and thermal stability than its corresponding semi‐IPN hydrogels. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Swelling behavior of semi‐interpenetrating polymer network hydrogels composed of poly(vinyl alcohol) and poly(acrylamide‐co‐sodium methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐sodium methacrylate) poly(AAm‐co‐SMA) were prepared by the semi IPN method. These IPN hydrogels were prepared by polymerizing aqueous solution of acrylamide and sodium methacrylate, using ammonium persulphate/N,N,N¹,N¹‐tetramethylethylenediamine (APS/TMEDA) initiating system and N,N¹‐methylene‐bisacrylamide (MBA) as a crosslinker in the presence of a host polymer, poly(vinyl alcohol). The influence of reaction conditions, such as the concentration of PVA, sodium methacrylate, crosslinker, initiator, and reaction temperature, on the swelling behavior of these IPNs was investigated in detail. The results showed that the IPN hydrogels exhibited different swelling behavior as the reaction conditions varied. To verify the structural difference in the IPN hydrogels, scanning electron microscopy (SEM) was used to identify the morphological changes in the IPN as the concentration of crosslinker varied. In addition to MBA, two other crosslinkers were also employed in the preparation of IPNs to illustrate the difference in their swelling phenomena. The swelling kinetics, equilibrium water content, and water transport mechanism of all the IPN hydrogels were investigated. IPN hydrogels being ionic in nature, the swelling behavior was significantly affected by environmental conditions, such as temperature, ionic strength, and pH of the swelling medium. Further, their swelling behavior was also examined in different physiological bio‐fluids. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 302–314, 2005     

Study of biomineralization of poly(vinyl alcohol)‐based scaffolds using an alternate soaking approach

The present work adds to the continuing efforts of designing a natural bone‐like structure by synthesizing a semi‐interpenetrating polymer network (IPN) of poly(vinyl alcohol)–poly[(acrylic acid)‐co‐acrylonitrile] and impregnating hydroxyapatite (HAP) into the polymer matrix by an alternate soaking process. The prepared HAP–polymer scaffolds were characterized using techniques like Fourier transform infrared spectroscopy, X‐ray diffraction, differential scanning calorimetry, thermogravimetric analysis and environmental scanning electron microscopy. The biomineralized semi‐IPN was evaluated for water sorption capacity and the data were utilized for calculating network parameters such as average molecular weight between crosslinks (M_c) and crosslink density (q). The impregnated HAP was quantified as a function of the chemical architecture of the semi‐IPN, number of reaction cycles and temperature of the swelling bath. Copyright © 2006 Society of Chemical Industry     

Synthesis and properties of the semi‐interpenetrating polymer network–like,thermosensitive poly(N‐isopropylacrylamide) hydrogel

A new strategy was used to prepare a semi‐interpenetrating polymer network (semi‐IPN)–like poly(N‐isopropylacrylamide) (PNIPAAm) polymeric hydrogel, consisting of either low (2300) or high (33,000) molecular weight linear PNIPAAm chains and the crosslinked PNIPAAm network. The properties of the resulting PNIPAAm hydrogels were characterized by DSC and SEM as well as their swelling ratios at various temperatures, the deswelling in hot water (48°C), and the oscillating shrinking–swelling properties within small temperature cycles. It was found that the deswelling rate of these semi‐IPN–like PNIPAAm hydrogels was improved if the molecular weight and/or composition of the linear PNIPAAm chains within the semi‐IPN–like PNIPAAm hydrogels were increased. This improved deswelling rate was attributed to the fast response nature of the linear PNIPAAm chains and the increased pore number in the matrix network, which provided numerous water channels for the water to diffuse out during the deswelling process at a temperature above the lower critical solution temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1935–1941, 2003     

Studies and characterization of RESOL/VAc–EHA/HMMM IPN systems in aqueous medium

Resol was solution‐blended with vinyl acetate‐2‐ethylhexyl acrylate (VAc–EHA) resin in an aqueous medium, in varying weight fractions, with hexamethoxymethylmelamine (HMMM) as a crosslinker and the data were compared with a control. The present work was aimed to obtain an optimum combination of high‐temperature resistance by synthesis of an interpenetrating network (IPN) of the resins. The control gave a semi‐IPN system, in which the resol crosslinked, while the acrylic did not, whereas the blend, where HMMM was the crosslinker, gave a full‐IPN system. FTIR spectra of the blends of resol/VAc–EHA/HMMM indicated the formation of new stretching, which was generated due to crosslinking reactions among VAc–EHA and the crosslinker HMMM. TGA showed that, with an increase in the VAc–EHA percent in semi‐IPNs, the decomposition temperature decreased gradually, whereas in case of full‐IPNs, the decomposition temperature increased with increase in the VAc–EHA percent. However, the full‐IPNs had a higher decomposition temperature than that of the semi‐IPNs, at the same resol/(VAc–EHA) ratio. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3581–3588, 2002     

Preparation of poly(methyl methacrylate‐co‐butyl methacrylate) nanoparticles and their reinforcing effect on natural rubber

Poly(methyl methacrylate‐co‐butyl methacrylate) [P(MMA‐co‐BMA)] nanoparticles were synthesized via emulsion polymerization, and incorporated into natural rubber (NR) by latex compounding. Monodispersed, core‐shell P(MMA‐co‐BMA)/casein nanoparticles (abbreviated as PMBMA‐CA) were produced with casein (CA) as surfactant. The chemical structure of P(MMA‐co‐BMA) copolymers were confirmed by ¹H‐NMR and FTIR analyses. Transmission electron microscopy demonstrated the core–shell structure of PMBMA‐CA, and PMBMA‐CA homogenously distributed around NR particles, indicating the interaction between PMBMA‐CA and NR. As a result, the tensile strength and modulus of NR/PMBMA‐CA films were significantly enhanced. The tensile strength was increased by 100% with 10% copolymer addition, when the molar ratio of MMA:BMA was 8:2. In addition, scanning electron microscopy and atomic force microscopy results presented that the NR/PMBMA‐CA films exhibited smooth surfaces with low roughness, and PMBMA‐CA was compatible with NR. FTIR‐ATR analyses also suggested fewer PMBMA‐CA nanoparticles migrated out of NR. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43843.     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation of poly(divinylbenzene‐co‐N‐isopropylacrylamide) microspheres and their hydrogen‐bonding assembly behavior for raspberry‐like core‐corona polymer composite

Narrowdisperse poly(divinylbenzene‐co‐N‐isopropylacrylamide) (poly(DVB‐co‐NIPAM)) functional microspheres with the diameter in the range of 630 nm and 2.58 μm were prepared by distillation–precipitation polymerization in neat acetonitrile in the absence of any stabilizer. The effect of N‐isopropylacrylamide (NIPAM) ratio in the comonomer feed on the morphology of the resultant polymer particles was investigated in detail with divinylbenzene (DVB) as crosslinker and 2,2′‐azobisisobutyronitrile (AIBN) as initiator. The monodisperse poly(DVB‐co‐NIPAM) microspheres with NIPAM fraction of 20 wt % were selected for the preparation of raspberry‐like core‐corona polymer composite by the hydrogen‐bonding self‐assembly heterocoagulation with poly(ethyleneglycol dimethacrylate‐co‐acrylic acid) [poly(EGDMA‐co‐AA)] nanospheres. Both of the functional poly(DVB‐co‐NIPAM) microspheres and the core‐corona particles were characterized with scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), and elemental analysis (EA). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1350–1357, 2007     

Phase‐separation prevention and performance improvement of poly(vinyl acetate)/TEOS hybrid using modified sol‐gel process

The formation of covalent bonds between silanols in copolymer and those in silica prevents organic–inorganic phase separation. Two series of hybrid composite materials, poly(vinyl acetate‐co‐vinyl trimethoxysilane)/TEOS and poly[vinyl acetate‐co‐3‐(trimethoxysilyl)propyl methacrylate]/TEOS, were fabricated using a modified sol‐gel process. The hybrids were transparent. Two kinds of silane coupling agents, vinyl trimethoxysilane (VTS) and 3‐(trimethoxysilyl)propyl methacrylate (γ‐MPS), were used to prevent macrophase separation through formation of covalent bonds. Thermal analysis showed that γ‐MPS was more effective than VTS for the formation of covalent bonds. Enhancement of thermal stability of the hybrids was investigated by thermogravimetric analysis. Photomicrographs of scanning electron microscopy and images of atomic force microscopy indicated that inorganic silica particles were homogeneously dispersed in less than 50 nm in organic matrix. The morphological properties of hybrids were strongly dependent on the organic–inorganic composition. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2310–2318, 2001     

Mechanical and dynamic mechanical studies of resol/vinyl acetate‐2‐ethylhexylacrylate/ hexamethoxymethylmelamine interpenetrating network systems

Resol was solution blended with vinyl acetate–2‐ethylhexylacrylate (VAc–EHA) resin in aqueous medium, in varying weight fractions, with hexamethoxymethylmelamine (HMMM) as crosslinker, and data was compared with a control. The present work was aimed at getting an optimum combination of tensile strength, dynamic mechanical strength, impact strength, and toughness by synthesis of an interpenetrating network (IPN) of the resins. The control gave a semi‐IPN system, in which the resol crosslinked, while the acrylic did not, whereas the blend, where HMMM was the crosslinker, gave a full IPN system. Full IPNs of the resol/VAc–EHA system had higher moduli and ultimate tensile strength than the semi‐IPNs. Dynamic mechanical study showed that full IPN systems have higher T_g values than semi‐IPN systems. The impact strength increases with increasing proportions of VAc–EHA copolymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1765–1771, 2003     

Preparation of hemispherical poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres by seeded preswelling emulsion polymerization

Seeded preswelling emulsion polymerization was carried out by using monodispersed poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] particles as the seed, and styrene and butyl acrylate as the second‐stage monomers under different polymerization conditions, to obtain hemispherical polystyrene (PST)‐rich–P4VP‐rich microspheres. Prior to polymerization, toluene was added into the preswelling system together with the second‐stage monomers. It was found that, with the increase of the amount of toluene, the particle morphology showed a tendency toward desirable hemispherical structure, and the colloidal stability of composite latex was improved. When the weight ratio of toluene/seed latex was increased up to 7.5/40 (g/g), the stable hemispherical latex could be obtained. However, when toluene was not added, the coagulum formed on the wall of the reactor during polymerization, and the composite particles with multiple surface domains (such as sandwich‐like, popcorn‐like) were formed. In addition, the final morphology of composite particles was influenced by the polarity of the seed crosslinker and the hydrophilicity of the second‐stage initiator, which could affect the mobility of poly(styrene‐co‐butyl acrylate) [P(ST‐BA)] chains. The morphology development during the polymerization was investigated in detail, and a schematic model was derived to depict the formation mechanism of hemispherical P(4VP‐BA)/P(ST‐BA) composite microspheres. The results revealed that the mobility of the P(ST‐BA) chains influenced the diffusion of the P(ST‐BA) domains on the surface of the P(4VP‐BA) matrix. When the mobility of the P(ST‐BA) chains allowed small‐size P(ST‐BA) domains to coalesce into one larger domain, complete phase‐separated morphology (hemisphere) could be achieved. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3811–3821, 2003     

Ethanol‐assisted dispersion of attapulgite and its effect on improving properties of alginate‐based superabsorbent nanocomposite

The dispersion of attapulgite (APT) as nanorod‐like single crystals is crucial to fully develop its functionality of one‐dimensional nanometer material as a filler of composite materials. In this study, APT was dispersed by the assistance of ethanol during the high‐pressure homogenization process to form individual nanorod‐like crystals. The dispersed APT was used to prepare new sodium alginate‐g‐poly(sodium acrylate‐co‐styrene)/attapulgite (NaAlg‐g‐P(NaA‐co‐St)/APT) superabsorbent nanocomposites. The effect of ethanol/water ratio on the dispersion of crystal bundles of APT was investigated by field emission scanning electron microscopy, and the results indicate that APT crystal bundles were effectively disaggregated in ν(CH₃CH₂OH) : ν(H₂O) ? 5 : 5 solution after homogenized at 50 MPa. The better dispersion of APT in NaAlg‐g‐P(NaA‐co‐St) matrix has clearly improved the gel strength (from 1300 Pa to 1410 Pa, ω = 100 rad/s), swelling capacity (442–521 g/g), swelling rate (3.3303–4.5736 g/g/s), and reswelling ability of the superabsorbent nanocomposite. Moreover, the nanocomposites showed fast swelling–deswelling responsive behavior in different saline solutions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Interpenetrating polymer networks based on poly(styrene‐co‐butylacrylate‐co‐hydroxyethyl methacrylate) and SiO2

Copolymer such as poly(styrene‐co‐butylacrylate‐co‐hydroxyethyl methacrylate) p (St‐BA‐HEMA) was prepared via free radical emulsion polymerization method. The resulting copolymer was converted to silicone secondary crosslinked interpenetrating polymer network (IPN) by condensation reaction with tetraethyl orthosilicate (TEOS). The obtained copolymers were characterized by using Fourier transform infrared spectroscopy (FTIR). Thermal properties of the copolymers were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Optical microscopy (OM) is used for studying the morphology, and then the effects of silicone concentrations, the reflux time, and composition on the phase morphology of P (St‐BA‐HEMA)‐SiO₂ IPNs were discussed. The broadening of the transition region was observed with the prolongation of the reflux time, and the tendency for aggregation of silicone on the surface was observed with Teflon as substrate plate. However, an optically transparent film was easily achieved at higher temperature due to the chemical crosslink and physical entanglement between the two phases of P (St‐BA‐HEMA)‐SiO₂. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Ionic conductivity and morphology of semi‐interpenetrating‐type polymer electrolyte entrapping poly(siloxane‐g‐allyl cyanide)

We prepared a semi‐IPN (interpenetrating network)‐type solid polymer electrolyte (SPE) using poly (ethylene glycol)dimethacrylate (PEGDMA) as a polymer matrix containing a monocomb‐type poly(siloxane‐g‐allyl cyanide) and poly(ethylene glycol)dimethylether (PEGDME) for the lithium secondary battery. The poly(siloxane‐g‐allyl cyanide)s were prepared by a hydrosilation reaction of poly (methyl hydrosiloxane) with allyl cyanide and characterized by ¹H NMR and FTIR. The semi‐IPN‐type electrolyte was prepared by thermal curing, and conductivities of samples were measured by impedance spectroscopy using an indium tin oxide (ITO) electrode. The ionic conductivity of the semi‐IPN‐polymer electrolyte was about 1.05 × 10^?5 S cm^?1 with 60 wt % of the poly(siloxane‐g‐allyl cyanide) and 6.96 × 10^?4 S cm^?1 with 50 wt % of the PEGDME and 10 wt % of the poly(siloxane‐g‐allyl cyanide) at 30°C. The SEM morphology of the cross section of the semi‐IPN‐polymer electrolyte film was changed from discontinuous network to continuous network as increasing the PEGDME content and decreasing the poly(siloxane‐g‐allyl cyanide) content. The mechanical stability was also enhanced when increasing the PEGDME content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of alginate/poly(N‐isopropylacrylamide) semi‐interpenetrating and fully interpenetrating polymer network hydrogels with γ‐ray irradiation and their swelling behaviors

Semi‐interpenetrating polymer network (semi‐IPN) and fully interpenetrating polymer network (full‐IPN) hydrogels composed of alginate and poly(N‐isopropylacrylamide) were prepared with γ‐ray irradiation. The semi‐IPN hydrogels were prepared through the irradiation of a mixed solution composed of alginate and N‐isopropylacrylamide (NIPAAm) monomer to simultaneously achieve the polymerization and self‐crosslinking of NIPAAm. The full‐IPN hydrogels were formed through the immersion of the semi‐IPN film in a calcium‐ion solution. The results for the swelling and deswelling behaviors showed that the swelling ratio of semi‐IPN hydrogels was higher than that of full‐IPN hydrogels. A semi‐IPN hydrogel containing more alginate exhibited relatively rapid swelling and deswelling rates, whereas a full‐IPN hydrogel showed an adverse tendency. All the hydrogels with NIPAAm exhibited a change in the swelling ratio around 30–40°C, and full‐IPN hydrogels showed more sensitive and reversible behavior than semi‐IPN hydrogels under a stepwise stimulus. In addition, the swelling ratio of the hydrogels continuously increased with the pH values, and the swelling processes were proven to be repeatable with pH changes. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4439–4446, 2006     

Long‐range‐ordered,hexagonally packed nanoporous membranes from degradable‐block‐containing diblock copolymer film templates

Polystyrene (PS)‐b‐polylactide (PLA) diblock copolymers with different molecular weights and fractions were synthesized through a combination of living anionic polymerization and controlled ring‐opening polymerization. Then, the PS–PLA films were guided to phase‐separate by self‐assembly into different morphologies through casting solvent selection, solvent evaporation, and thermal and solvent‐field regulation. Finally, perpendicularly oriented PS–PLA films were used as precursors for PS membranes with an ordered periodic nanoporous structure; this was achieved by the selective etching of the segregated PLA domains dispersed in a continuous matrix of PS. Testing techniques, including IR, ¹H‐NMR, gel permeation chromatography, scanning electron microscopy (SEM), and atomic force microscopy (AFM), were used to determine the chemical structure of the PS–PLA copolymer and its film morphology. AFM images of the self‐assembled PS‐PLA films indicate that vertical tapers of the PLA domains were generated among PS continuum when either toluene or tetrahydrofuran was used as the annealing solvent. The SEM images certified that the chemical etching of the PLA component from the self‐assembled PS–PLA films led to a long‐range‐ordered array of hexagonally packed nanoporous membranes with a diameter about 500 nm and a center‐to‐center distance of 1700 nm. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39638.     

Comparative delivery of Diltiazem hydrochloride through synthesized polymer: Hydrogel and hydrogel microspheres

In this study, interpenetrating polymer network (IPN) hydrogel based on polyvinyl alcohol (PVA) networking with polyacrylic acid (PAA) were prepared by a non‐conventional emulsion method without any added crosslinker, using benzoyl peroxide as initiator and sodium chloride (NaCl) as additive. The IPN hydrogel was characterized by using Fourier transformed infrared (FTIR) spectrophotometry, Thermo gravimetric analysis (TGA), and Scanning electron microscopy (SEM). (PVA‐co‐PAA)/NaCl normal IPN hydrogel (H) were fabricated into hydrogel microspheres (HM) by modified emulsion crosslinking method using glutaraldehyde‐saturated toluene as crosslinker and were loaded with Diltiazem hydrochloride (DL). The IPN hydrogel showed more swelling in simulated intestinal fluid (SIF). (PVA‐co‐PAA)/NaCl HM formulation A1 showed comparatively higher DL entrapment (79%) and better control over DL release up to 24 h. By comparing antihypertensive activity of DL loaded two formulations in normotensive rats, HM formulation A1 found more effective in reducing blood pressure to 40.1%. The experimental results demonstrated that (PVA‐co‐PAA)/NaCl HM had the greater potential than normal hydrogel to be used as a drug carrier. A single use of the prepared hydrogel microsphere system of DL can effectively control hypertension in rats. The system holds promise for clinical studies. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Membrane properties of microporous structures prepared from polyethylene/polymethacrylate IPN

Polyethylene/polymethacrylate interpenetrating polymer networks (PE/PMA IPN) form a matrix–particle or a co‐continuous morphology that can be adjusted by the composition and synthesis conditions. Based on the fact that PMA degrades whereas PE crosslinks when they are exposed to energetic irradiation, we developed a new approach to create a porous structure by electron beam irradiation. IPN systems that differ in the methacrylate components and composition were studied. One system contains poly(butyl methacrylate‐co‐methyl methacrylate) (BMA‐co‐MMA) and the other contains poly(dodecyl methacrylate‐co‐ethyl methacrylate) (DMA‐co‐EMA) as the PMA phase. After electron beam irradiation followed by extraction with xylene, both IPN systems have a porous structure that is permeable to water. However, the structure and size of the pores depend on the PMA components and the synthesis conditions. PMAs with long aliphatic side chains degrade less than PMAs containing only short aliphatic pendant groups. Therefore, the PE/BMA‐co‐MMA IPN forms bigger pores than PE/DMA‐co‐EMA, resulting in a higher water flux. The molecular cutoffs of the IPN are characteristic for microfiltration or ultrafiltration.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1976–1982, 2003     

Synthesis of polyethylene‐graft‐poly(styrene‐co‐maleic anhydride) and its compatibilizing effects on polyethylene/starch blends

Low density polyethylene (LDPE) was reacted with benzoyl peroxide (BPO) and 2,2,6,6‐tetramethyl‐l‐piperidinyloxy (TEMPO) to prepare a latent macroinitiator, PE–TEMPO. Little polymer was synthesized when maleic anhydride (MAH) was bulk polymerized in the presence of the PE–TEMPO. However, addition of styrene accelerated the polymerization rate and PE‐grafted‐poly(styrene‐co‐maleic anhyride) [PE‐g‐P(ST‐co‐MAH)] was produced to a high yield. Chemical reaction between MAH units and hydroxyl groups of starch was nearly undetectable in the PE/PE‐g‐P(ST‐co‐MAH)/starch blend system, and the tensile properties of the blend were not enhanced significantly. However, addition of tetrabutyl titanate (TNBT) during the blending procedure improved the tensile properties significantly through an increased interfacial adhesion between the components in the blend system. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2434–2438, 2003     

Temperature sensitive semi‐IPN microspheres from sodium alginate and N‐isopropylacrylamide for controlled release of 5‐fluorouracil

Semi‐interpenetrating network (IPN) of sodium alginate (NaAlg) and N‐isopropylacrylamide (NIPAAm) microspheres were prepared by water‐in‐oil (w/o) emulsification method. The microspheres were encapsulated with 5‐fluorouracil (5‐FU) and release patterns carried in 7.4 pH at temperatures of 25 and 37°C. The semi‐IPN microspheres were characterized by Fourier transform infrared spectroscopy (FTIR). Differential scanning calorimetry (DSC) and scanning electron microscopic studies were done on the drug‐loaded microspheres to confirm the polymorphism of 5‐FU and surface morphology of microspheres. These results indicated the molecular level dispersion of 5‐FU in the semi‐IPN microspheres. Particle size and size distribution were studied by laser light diffraction technique. Microspheres exhibited release of 5‐FU up to 12 h. The swelling studies were carried in 1.2 and 7.4 pH buffer media at 25 and 37°C. Drug release from NaAlg‐NIPAAm semi‐IPN microspheres at 25 and 37°C confirmed the thermosensitive nature by in vitro dissolution. The micro domains have released in a controlled manner due the presence of NIPAAm in the matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008