Role of silane coupling agents for performance improvement of poly(vinyl acetate)/tetraethyl orthosilicate hybrid composites prepared by a sol–gel process

Silica based poly(vinyl acetate)/inorganic hybrid composites were prepared via a sol–gel process under acidic conditions. Because the phase behaviour of the hybrids is greatly affected by weak interactions such as hydrogen bonding between organic polymer and inorganic network, two types of silane coupling agent (vinyl trimethoxysilane and 3‐(trimethoxysilyl)propyl methacrylate) were used to introduce specific interactions and to control phase behaviour in the interface between polymer and silica. The interfacial interactions between polymer and inorganic segment in the presence of silane have been investigated by Fourier transform infrared spectroscopy. Thermogravimetric analysis shows that the thermal stability of organic components in the hybrids is enhanced by addition of silane coupling agents. Scanning electron micrographs reveal that silica particles are homogeneously dispersed in the organic matrix as a result of the specific interactions. © 2001 Society of Chemical Industry     

Reaction‐induced phase separation in poly(vinyl acetate)/polyester blend

In blends of unsaturated polyester (UP), poly (vinyl acetate) (PVAc), and styrene, a reaction‐induced phase separation occurs upon curing that is due to the crosslinking between styrene and the UP molecules. The evolution of the morphology was observed by optical microscopy on a heated stage. Light transmission was used in parallel to precisely detect the onset of phase separation and the formation of microvoids. Using Fourier transform IR spectroscopy in the same conditions, the conversions at phase separation and at microvoiding were evaluated. Phase separation occurs at a very low degree of conversion and microvoiding develops at around 60% of conversion. The final morphology of the blend was investigated by scanning electron microscopy. The relative influences of the cure temperature, the concentration in PVAc, and the molecular weight of PVAc were investigated. It was confirmed that the early stages of the reaction at high temperature determine the final morphology of the blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3877–3888, 2006     

Nanocomposites of poly(propylene carbonate) reinforced with cellulose nanocrystals via sol‐gel process

Cellulose nanocrystals (CNCs) organogels were first produced from aqueous dispersion through solvent exchange of CNCs to acetone via a simple sol‐gel process. After mixing the organogels with poly(propylene carbonate) (PPC) in dimethylformamide followed by solution casting, green nanocomposites were obtained with CNCs well dispersed in PPC polymer matrix which was confirmed by scanning electron microscopy observations. Differential scanning calorimeter analysis revealed that glass transition temperature of the nanocomposites was slightly increased from 34.0 to 37.4°C. Tensile tests indicated that both yield strength and Young's modulus of CNCs/PPC nanocomposites were doubled by adding 10 wt % CNCs. However, poor thermal stability of PPC occurred after incorporating with CNCs due to the thermo‐sensitive sulfate groups located on the surface of CNCs. Furthermore, PPC became more hydrophilic because of the inclusion of CNCs according to the water contact angle measurement. The enhanced mechanical and hydrophilic properties, coupled with the inherent superior biocompatibility and degradability, offered CNCs/PPC composites potential application in biomedical fields. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40832.     

Phase separation in styrenated polyester resin containing a poly(vinyl acetate) low-profile additive

Scanning electron microscopy has been used to observe morphology in styrenated polyester resins containing poly(vinyl acetate) (PVA). Resins containing 8% PVA form composite spherical particles which occupy 35 vol% of the total material. It is concluded that these particles consist of resin sub-inclusions embedded in the continuous matrix of polyester resin. Increasing the PVA content to 16% results in a phase inversion: PVA forms the matrix, and the resin is present as spherical particles. These observations are interpreted with the aid of a ternary diagram.     

Properties and structure of poly(vinyl alcohol)/silica composites

The relationships between the properties and structure are discussed for poly(vinyl alcohol)(PVA)/silica composites prepared through the sol‐gel process. The composites became stiff and brittle with increasing the silica content. The properties of the composites were changed drastically at around the composition of PVA/silica = 70/30 wt %. For example, there was no large change in the Young's modulus above 30 wt % of silica content (Pure PVA: 31.8 MPa, silica 30%: 52.6 MPa, silica 50%: 55.2 MPa). Consequently, it was considered that the three‐dimensional network structure of silica could be formed in the composite with more than 30 wt % of silica in PVA. From this behavior, it could be considered that the crystal growth of PVA was remarkably inhibited by silica network. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 133–138, 1999     

Manufacturing and characterizations of flexible poly(dimethylsiloxane)/poly(vinyl acetate)/polythiophene ternary composite films

ABSTRACT

In this study, polythiophene and poly(dimethylsiloxane)/poly(vinyl acetate)/polythiophene ternary composites were synthesized. The new ternary composites obtained in powder and film forms were characterized using various techniques. Magnetic properties of all the materials were analyzed by Gouy balance measurements, and it was found that their conductivity mechanism is of polaron nature. The surface structure, surface roughness, and thermal properties of the prepared samples were identified by Scanning Electron Microscopy, Atomic Force Microscopy, and Thermogravimetric Analysis, respectively. The tensile-tension test studies were performed for mechanical properties. The PDMS/PVAc/PT (6%) composite demonstrated about 50% of the maximum strain value (%) of vulcanized natural rubber.     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Synthesis and characterization of poly(methyl acrylate‐co‐itaconic anhydride)/TiO2 hybrid materials via sol–gel process

In the presence of 3‐aminopropyltriethoxysilane (APTES), the transparent and yellowish poly(methyl acrylate‐co‐itaconic anhydride)/TiO₂ [P(MA‐co‐Itn)/TiO₂] hybrid materials were prepared from the copolymer of methyl acrylate and itaconic anhydride [P(MA‐co‐Itn)] and tetrabutyl titanate (TBT) via a sol–gel process. At first, the triethoxysilane groups were incorporated into the copolymer P(MA‐co‐Itn) as pendant side chains by the aminolytic reaction between the itaconic anhydride units of the copolymer and the amino group of 3‐aminopropyltriethoxysilane (APTES), and then the covalent bonds between the organic and inorganic phases were introduced by the hydrolysis and polycondensation of the triethoxysilane groups on the copolymer with TBT. FTIR analysis proved the existence of the covalent bonds. The influences of APTES on glass transition and morphology of the hybrid materials was studied by differential scanning calorimetry, scanning electron microscope, and atomic force microscope. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1763–1768, 2000     

Poly(ethylene‐co‐vinyl acetate)‐graft‐poly(methyl methacrylate) (EVA‐graft‐PMMA) as a modifier of epoxy resins

Conventional approaches to toughen thermosets are: (1) the polymerization‐induced phase separation of a rubber or a thermoplastic, or (2) the use of a dispersion of preformed particles in the initial formulation. In the present study it is shown that it is possible to combine both techniques by using graft copolymers with one of the blocks being initially immiscible and the other that phase separates during polymerization. This is illustrated by the use of poly(ethylene‐co‐vinyl acetate)‐graft‐poly(methyl methacrylate) (EVA‐graft‐PMMA) as modifier of an epoxy resin. EVA is initially immiscible and PMMA phase separates during polymerization. Blends of an epoxy monomer based on diglycidylether of bisphenol A (DGEBA, 100 parts by weight), piperidine (5 parts by weight), and PMMA (5 parts by weight), showed the typical polymerization‐induced phase separation of PMMA‐rich domains before gelation of the epoxy network. Replacing PMMA by EVA‐graft‐PMMA (5 parts by weight), yielded stable dispersions of EVA blocks, favoured by the initial solubility of PMMA blocks. Phase separation of PMMA blocks in the course of polymerization led to a dispersion of in situ generated biphasic particles (plausibly composed of EVA cores surrounded by PMMA shells), with average diameters varying from 0.3 to 0.6 µm with the cure temperature. This procedure may be used to generate stable dispersions of biphasic particles for toughening purposes. © 2002 Society of Chemical Industry     

Phase separation in poly(vinyl alcohol)/gelatin blend systems

Blends of a commercial poly(vinyl alcohol) (a-PVA) derived from vinyl acetate and gelatin obtained from collagen were prepared by mixing aqueous solutions of both samples under various conditions. For the blend hydrogels, the depression of melting temperatures was observed at high PVA content. Similarly to the a-PVA/silk fibroin (SF) system, when the degrees of polymerization of PVA increased, the microphase separation region in a phase diagram of the blend films increased for the a-PVA/gelatin system. In the IR spectra of the blend films, no absorption bands corresponding to a conformational change of gelatin appeared. Comparison of the mechanical properties of the a-PVA/gelatin and a-PVA/SF systems, showed the interaction between PVA and gelatin molecules to be smaller than that between PVA and SF molecules. © 1999 Society of Chemical Industry     

Silane‐modified poly(ethylene‐co‐vinyl acetate): influence of comonomers on peroxide‐initiated vinylsilane grafting

Functionalization of poly(ethylene‐co‐vinyl acetate) (EVA) with vinyltriethoxysilane (VTEOS) has been carried out by a free‐radical melt‐grafting procedure in the presence of added comonomers. The influence of comonomers on silane graft yield and crosslink density has been assessed. Experiments were performed on masterbatches of EVA, VTEOS (5 wt %), peroxide initiator (L‐231, 0.05 wt %), and comonomer (0–1 comonomer : VTEOS mole ratio) prepared at 90°C. Melt‐grafting experiments were carried out at 145°C in an oscillating disk rheometer (ODR), which measured crosslink density during the grafting process. Silane graft yields were determined by proton NMR spectroscopy. Comonomers evaluated were maleic anhydride (MAn), 1‐vinyl‐2‐pyrrolidone (VP), and 1‐dodecene (DD). At the comonomer ratios examined, MAn suppressed both silane grafting and peroxide‐initiated crosslinking. Both VP and DD, however, exhibited greater selectivity in suppressing crosslinking than silane grafting; optimum performance was found at a comonomer : vinylsilane mole ratio of 0.2. None of the comonomers studied enhanced the level of silane grafting. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1308–1314, 2000     

Thermal and spectroscopic studies of poly(N‐vinyl pyrrolidone)/poly(vinyl alcohol) blend films

Poly(N‐vinyl pyrrolidone) (PVP) and poly (vinyl alcohol) (PVA) homopolymers and their blended samples with different compositions were prepared using cast technique and subjected to X‐ray diffraction (XRD) measurements, infrared (IR) spectroscopy, ultraviolet/visible spectroscopy, and thermogravimetric analysis (TGA). XRD patterns of homopolymers and their blended samples indicated that blending amorphous materials, such as PVP, with semicrystalline polymer, such as PVA, gives rise to an amorphous structure with two halo peaks at positions identical to those found in pure PVP. Identification of structure and assignments of the most evident IR ‐ absorption bands of PVP and PVA as well as their blends in the range 400–2000 cm^?1 were studied. UV–vis spectra were used to study absorption spectra and estimate the values of absorption edge, E_g, and band tail, E_e, for all samples. Making use of Coats‐Redfern relation, thermogravimetric (TG) data allowed the calculation of the values of some thermodynamic parameters, such as activation energy E, entropy ΔS^#, enthalpy ΔH, and free energy of activation ΔG^# for different decomposition steps in the samples under investigation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The effectiveness of magnesium carbonate‐based flame retardants for poly(ethylene‐co‐vinyl acetate) and poly(ethylene‐co‐ethyl acrylate)

In this report we outline recent work on the evaluation of magnesium carbonate‐based flame retardants for polymers commonly used in halogen‐free flame retardant wire and cable applications: poly(ethylene‐co‐vinyl acetate) (EVA) and poly(ethylene‐co‐ethyl acrylate) (EEA). Natural magnesium carbonate (magnesite), synthetic magnesium carbonate (hydromagnesite), and hydromagnesite/huntite blends were combined with EVA or EEA and tested for flame retardancy effectiveness with the cone calorimeter. The flammability results showed that the effectiveness of these carbonates was polymer dependent, suggesting that polymer degradation chemistry played a role in the flammability reduction mechanism. Hydromagnesites were, in general, more effective in reducing flammability, being comparable in performance to magnesium hydroxide. Finally, we report some polymer–clay (organically treated montmorillonite and magadiite) + magnesium carbonate flame retardant results which showed that the nanocomposite yielded mixed results. Specifically, the polymer–clay nanocomposite samples did not always yield the greatest reductions in peak heat release rate. Copyright © 2007 John Wiley & Sons, Ltd.     

Influence of hydrogen donors on peroxide‐initiated melt grafting of vinylsilane to poly(ethylene‐co‐vinyl acetate)

A technique has been examined for reducing the extent of crosslinking resulting from 1,1‐di(t‐butylperoxy)‐3,3,5‐trimethylcyclohexane (L‐231) initiating melt grafting of vinyltriethoxysilane (VTEOS) onto poly(ethylene‐co‐vinyl acetate) (EVA). Using measurements of crosslink density and VTEOS conversion, a standard of selectivity for the EVA/VTEOS/L‐231 system at 145 °C was defined and used to assess the influence of a range of additives (0.25 mol per mole VTEOS). The data indicated that compounds such as 4‐nonene, N,N‐dimethylaniline, and cumene improve reaction selectivity, whereas dodecane and cyclohexyl acetate have no effect. A strong correlation between the minimum C? H bond dissociation energy and the influence of a given compound is evident, suggesting that a labile C? H bond is the key element of an effective additive. A mechanism of additive function on the basis of hydrogen atom donation is proposed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2397–2402, 2002     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Diffusion of solvents in poly(vinyl acetate) and partially and fully hydrolyzed poly(vinyl alcohol)

Diffusivities of methyl acetate, methanol and water in poly(vinyl acetate) and fully and partially hydrolyzed poly(vinyl alcohol) have been measured by capillary column inverse gas chromatography and/or gravimetric sorption. Data from the literature have been used when available for comparison. Overall the diffusivities show good consistency in terms of their temperature and concentration dependences. The free‐volume model has been applied to all the data with excellent results. In most cases the dramatic changes in diffusivities with temperature and concentration can be captured using only a few experimental data points and two regression parameters. This demonstrates that the free‐volume theory is a valuable tool for the design of equipment for processing and devolatilization of polymer ? solvent systems. © 2013 Society of Chemical Industry     

Use of pyrolyzed oil shale as filler in poly(ethylene‐co‐vinyl acetate) with different vinyl acetate contents

Pyrolyzed oil shale (POS) obtained from the pyrolysis of bituminous rock was used as filler in poly(ethylene‐co‐vinyl acetate) (EVA). The effects of the VA content of EVA and the particle size of POS on the mechanical properties were investigated. The composites were prepared in a rotor mixer at 180°C with a concentration of POS of up to 30 wt %. The stress–strain plots of the compression‐molded composites are similar to the EVA (18% VA content) behavior for low concentrations (1–5 wt %) of POS with a particle size lower than 270 mesh. It was observed that decreasing the POS particle size and increasing the VA content of EVA produced better compatibility between the polymer and filler. The mechanical properties, differential scanning calorimetry, and dynamic mechanical analysis also demonstrated the compatibility between EVA and POS under the increase of the VA content in the EVA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1544–1555, 2002; DOI 10.1002/app.10494     

Enzymatic degradation of poly(D,L‐lactide) and its blends with poly(vinyl acetate)

The enzymatic degradation of poly(D ,L ‐lactide) (PLA) was investigated using two different lipases, Novozym 435 and Lipolase. The optimum temperature was 50°C for the enzymatic degradation of PLA. The effect of various solvents on the degradation of PLA was investigated at 50°C using Novozym 435, and toluene was found to be the best solvent among the solvents investigated. The enzymatic degradation of the blends of PLA and PVAc was investigated at 50°C in toluene. The enzymatic degradation of the blends of PLA and PVAc showed that there is an interaction between the polymers during degradation, which results in the reduction of degradation rate of both polymers in the blend. A continuous distribution model was used to determine the rate coefficients for polymer degradation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 657–680 2006     

聚(丙烯腈/醋酸乙烯酯)/蒙脱土纳米复合材料的流变性能

研究了聚(丙烯腈/醋酸乙烯酯)/蒙脱土[P(AN/VAc)/Clay]纳米复合材料的溶解特性及其在二甲基乙酰胺(DMA)溶剂中的流变性能。结果表明,P(AN/VACc)/Clay在溶液纺丝时最佳的溶剂为DMA; P(AN/VAc)/Clay-DMA溶液的非牛顿流动指数小于1,溶液为假塑性流体;当溶液质量分数为12%-13%、温度为130-150℃时,P(AN/VAc)/Clay-DMA溶液的纺丝性能最佳     

Extensional viscosity measurements and characterization of poly (vinyl chloride‐co‐vinyl acetate) plastisols and foams

The foaming of PVC‐VA [Poly (vinyl chloride‐co‐vinyl acetate)] plastisols is a complex combination of processes involving the simultaneous curing of the paste with the evolution of gases caused by the decomposition of the chemical blowing agent. The extensional viscosity is a fundamental characteristic of the material, responsible for the behavior of the system when undergoing the extensional stress produced by the released gases. Nevertheless, such changes have not been considered to the same extent as the complex viscosity evolution or the thermal processes suffered by PVC‐VA plastisols. The objective of the present work is to study the extensional viscosity of the PVC‐VA plastisols prepared with three plasticizers of similar structure, but with different curing and rheological behavior in order to investigate its influence on the quality of the foams obtained. Extensional viscosity measurements under forced prestretch conditions revealed that depending on the structure and consequently on the compatibility of the plasticizer used, each plastisol develops its properties and structure accordingly. DINCH plasticizer (Diisononyl cyclohexane‐1,2‐dicarboxylate presenting alicyclic ring) seems to be the less compatible compared with the other two studied (both presenting aromatic rings) according to its behavior during the curing and foaming processes and may not be able to withstand the pressure evolved by the released gases during the foaming process yielding foams of poorer quality. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013