Porous biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): physical properties,morphology, and biodegradation

Poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their films without or blended with 50 wt% poly(ethylene glycol) (PEG) were prepared by solution casting. Porous films were obtained by water‐extraction of PEG from solution‐cast phase‐separated PLLA‐blend‐PCL‐blend‐PEG films. The effects of PLLA/PCL ratio on the morphology of the porous films and the effects of PLLA/PCL ratio and pores on the physical properties and biodegradability of the films were investigated. The pore size of the blend films decreased with increasing PLLA/PCL ratio. Polymer blending and pore formation gave biodegradable PLLA‐blend‐PCL materials with a wide variety of tensile properties with Young's modulus in the range of 0.07–1.4 GPa and elongation at break in the range 3–380%. Pore formation markedly increased the PLLA crystallinity of porous films, except for low PLLA/PCL ratio. Polymer blending as well as pore formation enhanced the enzymatic degradation of biodegradable polyester blends. Copyright © 2006 Society of Chemical Industry     

Porous biodegradable polyesters. I. Preparation of porous poly(L‐lactide) films by extraction of poly(ethylene oxide) from their blends

Porous poly(L ‐lactide) (PLLA) films were prepared by water extraction of poly(ethylene oxide) (PEO) from solution‐cast PLLA and PEO blend films. The dependence of blend ratio and molecular weight of PEO on the porosity and pore size of films was investigated by gravimetry and scanning electron microscopy. The film porosity and extracted weight ratio were in good agreement with the expected for porous films prepared using PEO of low molecular weight (M_w = 1 × 10³), but shifted to lower values than expected when high molecular weight PEO (M_w = 1 × 10⁵) was utilized. The maximum pore size was larger for porous films prepared from PEO having higher molecular weight, when compared at the same blending ratio of PLLA and PEO before water extraction. Differential scanning calorimetry of as‐cast PLLA and PEO blend films revealed that PLLA and PEO were phase‐separated at least after solvent evaporation. On the other hand, comparison of blend films before and after extraction suggested that a small amount of PEO was trapped in the amorphous region between PLLA crystallites even after water extraction and hindered PLLA crystallization during solvent evaporation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 629–637, 2000     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Blends of aliphatic polyesters. III. Biodegradation of solution-cast blends from poly(L-lactide) and poly(ε-caprolactone)

Phase-separated blend films were prepared with the solution casting method from poly(L -lactide) (PLLA) and poly(ε-caprolactone) (PCL) with different PLLA contents [X_PLLA (w/w) = PLLA/(PCL + PLLA)] and their biodegradation was investigated in soil up to 20 months by gravimetry, gel permeation chromatography, tensile testing, differential scanning calorimetry, and scanning electron microscopy. The nonblended PCL film and the blend film with X_PLLA = 0.25 disappeared in 4 and 12 months, respectively, while most of the initial mass remained for the blend film of X_PLLA = 0.75 and the nonblended PLLA film. The decrease in weight remaining, molecular weight, tensile strength, and elongation-at-break was higher for blend films of low X_PLLA. The melting temperature of PLLA in blend films of X_PLLA = 0.5 and 0.75, and of nonblended film, remained around 179°C upon biodegradation in soil for 20 months. The preferred biodegradation of PCL in blend films resulted in formation of microspheres of a PLLA-rich phase at the surface for the blend film of X_PLLA = 0.25 and the porous structure for blend films of X_PLLA = 0.5 and 0.75. Comparison of the weight loss of blend films in biodegradation in soil with that of the nonenzymatic hydrolysis in phosphate-buffered solution revealed preferred enzymatic degradation of PCL and insignificant attack to PLLA in the blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2259–2268, 1998     

Blends of crystalline and amorphous poly(lactide). III. Hydrolysis of solution-cast blend films

Hydrolysis of blend films prepared from amorphous poly(DL-lactide) (a-PLA) and isotactic crystalline poly(D- or L-lactide) (c-PLA) having different c-PLA contents [X = c-PLA/(a-PLA + c-PLA)] was performed in phosphate buffered solution of pH 7.4 at 37°C. The blend films before and after hydrolysis were studied using gel permeation chromatography, tensile testing, differential scanning calorimetry (DSC), and optical rotation. The mass of the blend films remaining after hydrolysis of longer than 20 months was larger with the increasing initial X. The tensile strength of the blend films remained unchanged in the early stage of hydrolysis, followed by a rapid decrease with time, the duration of period for the tensile strength remaining unchanged was longer for the blend films of smaller X. The change in crystallinity, molecular weight, and specific optical rotation during hydrolysis of the blend films revealed that degradation took place preferentially in the amorphous region than in the crystalline region of the blend films. A double melting peak was observed in the DSC spectra of blend films with X = 0.75 and 0.5 after hydrolysis for 20 months. The time difference in the induction of reduction between the tensile strength and the mass due to hydrolysis of the blend films increased with an increase in X. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 855–863, 1997     

Enzymatic degradation of blends of poly(ε‐caprolactone) and poly(styrene‐co‐acrylonitrile) by Pseudomonas lipase

In polymer blends, the composition and microcrystalline structure of the blend near surfaces can be markedly different from the bulk properties. In this study, the enzymatic degradation of poly(ε‐caprolactone) (PCL) and its blends with poly(styrene‐co‐acrylonitrile) (SAN) was conducted in a phosphate buffer solution containing Pseudomonas lipase, and the degradation behavior was correlated with the surface properties and crystalline microstructure of the blends. The enzymatic degradation preferentially took place at the amorphous part of PCL film. The melt‐quenched PCL film with low crystallinity and small lamellar thickness showed a higher degradation rate compared with isothermally crystallized (at 36, 40, and 44°C) PCL films. Also, there was a vast difference in the enzymatic degradation behavior of pure PCL and PCL/SAN blends. The pure PCL showed 100% weight loss in a very short time (i.e., 72 h), whereas the PCL/SAN blend containing just 1% SAN showed ～50% weight loss and the degradation ceased, and the blend containing 40% SAN showed almost no weight loss. These results suggest that as degradation proceeds, the nondegradable SAN content increases at the surface of PCL/SAN films and prevents the lipase from attacking the biodegradable PCL chains. This phenomenon was observed even for a very high PCL content in the blend samples. In the blend with low PCL content, the inaccessibility of the amorphous interphase with high SAN content prevented the attack of lipase on the lamellae of PCL. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 868–879, 2002     

Blends of aliphatic polyesters. IV. Morphology,swelling behavior,and surface and bulk properties of blends from hydrophobic poly(L-lactide) and hydrophilic poly(vinyl alcohol)

Blend films were prepared from hydrophobic poly(L -lactide) (PLLA) and hydrophilic poly(vinyl alcohol) (PVA) with different PLLA contents [X_PLLA (w/w) = PLLA/(PVA + PLLA)] by solution casting and melt quenching. Their morphology, swelling behavior, and surface and bulk properties were investigated. Polarizing optical microscopy, scanning electron microscopy, differential scanning calorimetry, X-ray diffractometry, and tensile testing revealed that PLLA and PVA were phase separated in these blend films and the PLLA-rich and PVA-rich phases both formed a continuous domain in the blend film of X_PLLA = 0.5. The water absorption of the blend films was higher for the blend films of low X_PLLA values when compared at the same immersion time, and it was larger than expected from those of nonblended PLLA and PVA films. The dynamic contact angles of the blend films were linearly increased with an increase in X_PLLA. The tensile strength and Young's modulus of the dry blend films decreased with a rise in X_PLLA, but this dependence was reversed because of the large decreases in tensile strength and Young's modulus for the blend films having high X_PLLA values after immersion in water. The elongation at break was higher for the wet blend film than for the dry blend film when compared at the same X_PLLA and that of the dry and wet blend films decreased with an increase in X_PLLA. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2151–2160, 2001     

Blends of aliphatic polyesters. II. Hydrolysis of solution-cast blends from poly(L-lactide) and poly(E-caprolactone) in phosphate-buffered solution

Blend films were prepared from poly(L -lactide) (PLLA) and poly(E-caprolactone) (PCL) with different PLLA contents [X_PLLA (w/w) = PLLA/(PCL + PLLA)] by the solution-casting method and their hydrolysis behaviors were investigated up to 20 months in a phosphate-buffered solution of pH 7.4 at 37°C by gel permeation chromatography, tensile testing, differential scanning calorimetry, and gravimetry. Polarizing microscopic observation and dynamic mechanical analysis revealed that PCL and PLLA were phase-separated in blend films before hydrolysis. The mass remaining, molecular weight, and tensile strength of the blend films with X_PLLA of 0.5 and 0.75 decreased more rapidly by hydrolysis than those of the nonblended PLLA, while the elongation at break of the blend film of X_PLLA = 0.25 decreased the slowest. The rate constant for hydrolysis (k) calculated from the M_n change during hydrolysis was higher for blend films of X_PLLA = 0.5 and 0.75 than those expected from k of nonblended PLLA and PCL. The melting temperature (T_m) of PLLA in the blend and nonblended films of X_PLLA = 0.5, 0.75, and 1 decreased from 179 to 161, 160, and 175°C upon hydrolysis for 20 months, respectively, while that for X_PLLA = 0.25 slightly increased from 176 to 177°C. On the other hand, T_m and the crystallinity of PCL was significantly increased by hydrolysis for 20 months, irrespective of X_PLLA. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 405–415, 1998     

Morphological,thermal, and mechanical properties of poly(ε‐caprolactone)/poly(ε‐caprolactone)‐grafted‐cellulose nanocrystals mats produced by electrospinning

Electrospun nanocomposites of poly(ε‐caprolactone) (PCL) incorporated with PCL‐grafted cellulose nanocrystals (PCL‐g‐CNC) were produced. PCL chains were grafted from cellulose nanocrystals (CNC) surface by ring‐opening polymerization. Grafting was confirmed by infrared spectroscopy (FTIR) and thermogravimetric analyses (TGA). The resulting PCL‐g‐CNC were then incorporated into a PCL matrix at various loadings. Homogeneous nanofibers with average diameter decreasing with the addition of PCL‐g‐CNC were observed by scanning electron microscopy (SEM). PCL‐g‐CNC domains incorporated into the PCL matrix were visualized by transmission electron microscopy (TEM). Thermal and mechanical properties of the mats were analyzed by differential scanning calorimetry (DSC), TGA and dynamic mechanical analysis (DMA). The addition of PCL‐g‐CNC into the PCL matrix caused changes in the thermal behavior and crystallinity of the electrospun fibers. Significant improvements in Young's modulus and in strain at break with increasing PCL‐g‐CNC loadings were found. These results highlighted the great potential of cellulose nanocrystals as a reinforcement phase in electrospun PCL mats, which can be used as biomedical materials. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43445.     

Poly(ethyl glycol) assisting water sorption enhancement of poly(ε‐caprolactone) blend for drug delivery

Poly(ε‐caprolactone) (PCL) has been thermally synthesized, and then fractionated to blend with poly(ethyl glycol) (PEG). Blend films of PCL and PEG have been prepared by solution casting. Fourier transform infrared spectrum and differential scanning calorimetry of the films have been carried out, and the results indicate some hydrogen bonding interaction between the two components, which is resulted from the carbonyl groups of PCL and the hydroxyl end‐groups of the low‐molecular‐weight PEG. Scanning electron microscope images of the blend films reveal porous network structures for their surfaces and for their inner parts and the porous structure becomes more pronounced with the increase of PEG in the blend film. Ibuprofen (IBU) was used as the model drug to test the drug release behavior for the PCL/PEG blend matrices. The results show that IBU could be released from the blend tablets rapidly, and the release rate increases with PEG content. Analysis of the release profiles indicates PCL erosion control release mechanism of pure PCL tablet, but drug diffusion control of the blend tablet, because PEG can absorb water to allow water feasible to diffuse into drug core and dissolve drug. Therefore, the interconnected channels in the blend matrices and the hydrophilic nature of PEG contribute to the improvement of the IBU release rate. The research indicates that drug release rate from PCL based material could be efficiently improved by addition of small amount of hydrophilic low‐molecular‐weight PEG. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Properties and morphology of poly(L‐lactide). III. Effects of initial crystallinity on long‐term in vitro hydrolysis of high molecular weight poly(L‐lactide) film in phosphate‐buffered solution

The effects of crystallinity (x_c) on the hydrolysis of high molecular weight poly(L ‐lactide) (PLLA) films in a phosphate‐buffered solution at 37°C was investigated by gel permeation chromatography, tensile testing, differential scanning calorimetry, scanning electron microscopy, and polarizing optical microscopy. The change in molecular weight distribution and surface morphology of the PLLA films after hydrolysis revealed that the hydrolysis of PLLA film in a phosphate‐buffered solution proceeded homogeneously along the film cross section, mainly via the bulk‐erosion mechanism. The induction period until the start of the decrease in mass remaining and the tensile strength became longer with a decrease in the initial x_c of the PLLA films. The rate of molecular weight reduction was higher as the initial x_c of the PLLA films increased when hydrolysis was carried out up to 24 months. Melting and glass transition temperatures of the PLLA films increased in the first 12 months of hydrolysis, while they decreased in another 24 months, irrespective of the initial x_c. The x_c value of the PLLA films increased monotonously by hydrolysis. The lamella disorientation in PLLA spherulites after hydrolysis implied that the hydrolysis of PLLA chains occurred predominantly in the amorphous region between the crystalline regions in the spherulites. The area of a specific molecular weight in GPC spectra at 36 months increased with increase in the initial x_c of the PLLA film, suggesting that the specific peak should be due to the component of one fold in the crystalline region. The reason for enhanced hydrolysis of PLLA films having higher initial crystallinities was discussed in terms of tie chains and terminal groups of PLLA. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1452–1464, 2000     

Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Morphology and hydrolysis of PCL/PLLA blends compatibilized with P(LLA‐co‐ϵCL) or P(LLA‐b‐ϵCL)

The effect of the compatibilizers, P(LLA‐co‐?CL) and P(LLA‐b‐?CL), on the morphology and hydrolysis of the blend of poly(?‐caprolactone) (PCL) and poly(L ‐lactide) (PLLA) was investigated. An addition of P(LLA‐co‐?CL) or P(LLA‐b‐?CL) into the blend could enhance the compatibility between the dispersed PCL domains and the PLLA matrix. The size of the PCL domains in the PLLA/PCL (70/30) blend containing P(LLA‐co‐?CL) reduced more significantly with an increase in the content of the compatibilizer than that in the blend containing P(LLA‐b‐?CL). The molecular weight of the PLLA/PCL blend films compatibilized with P(LLA‐co‐?CL) or P(LLA‐b‐?CL) decreased during the hydrolysis and the decrease of the molecular weight of the blend films compatibilized with P(LLA‐co‐?CL) was much more significant than that of the blend films compatibilized with P(LLA‐b‐?CL). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1892–1898, 2002     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermally induced crystallization and enzymatic degradation studies of poly (L‐lactic acid) films

Poly(L ‐lactic acid) (PLLA) films with different crystallinities were prepared by solvent casting and subsequently annealed at various temperatures (T_a) (80–110°C). The effects of crystallinity on enzymatic degradation of PLLA films were examined in the presence of proteinase K at 37°C by means of weight loss, DSC, FTIR spectroscopy, and optical microscopy. DSC and the absorbance ratio of 921 and 956 cm^?1 (A₉₂₁/A₉₅₆) were used to evaluate crystallinity changes during thermally induced crystallization and enzymatic hydrolysis. The highest percentage of weight loss was observed for the film with the lowest initial crystallinity and the lowest percentage of weight loss was observed for the film with highest crystallinity. FTIR investigation of degraded films showed a band at 922 cm^?1 and no band at 908 cm^?1 suggested that all degraded samples form α crystals. The rate of degradation was found to depend on the initial crystallinity of PLLA film and shown that enzymatic degradation kinetics followed first‐order kinetics for a given enzyme concentration. DSC crystallinity and IR absorbance ratio, A₉₂₁/A₉₅₆ ratio, showed no significant changes with degradation time for annealed PLLA films whereas as‐cast PLLA film showed an increase in crystallinity with degradation; this revealed that degradation takes place predominantly in the free amorphous region of annealed PLLA films without changing long range and short range order © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

Poly(ϵ-caprolactone)/poly(ethylene oxide) diblock copolymer II. Nonisothermal crystallization and melting behavior

The nonisothermal crystallization behavior and melting process of the poly(ϵ-caprolactone) (PCL)/poly(ethylene oxide) (PEO) diblock copolymer in which the weight fraction of the PCL block is 0.80 has been studied by using differential scanning calorimetry (DSC). Only the PCL block is crystallizable, the PEO block with 0.20 weight fraction cannot crystallize. The kinetics of the PCL/PEO diblock copolymer under nonisothermal crystallization conditions has been analyzed by Ozawa's equation. The experimental data shows no agreement with Ozawa's theoretical predictions in the whole crystallization process, especially in the later stage. A parameter, kinetic crystallinity, is used to characterize the crystallizability of the PCL/PEO diblock copolymer. The amorphous and microphase separating PEO block has a great influence on the crystallization of the PCL block. It bonds chemically with the PCL block, reduces crystallization entropy, and provides nucleating sites for the PCL block crystallization. The existence of the PEO block leads to the occurrence of the two melting peaks of the PCL/PEO diblock copolymer during melting process after nonisothermal crystallization. The comparison of nonisothermal crystallization of the PCL/PEO diblock copolymer, PCL/PEO blend, and PCL and PEO homopolymers has been made. It showed a lower crystallinity of the PCL/PEO diblock copolymer than that of others and a faster crystallization rate of the PCL/PEO diblock copolymer than that of the PCL homopolymer, but a slower crystallization rate than that of the PCL/PEO blend. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1793–1804, 1997     

Blends of aliphatic polyesters. VIII. Effects of poly(L‐lactide‐co‐ε‐caprolactone) on enzymatic hydrolysis of poly(L‐lactide), poly(ε‐caprolactone), and their blend films

Poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their blend (50/50) films containing different amounts of poly(L ‐lactide‐co‐ε‐caprolactone) (PLLA‐CL), were prepared by solution casting. The effects of added PLLA‐CL on the enzymatic hydrolysis of the films were investigated in the presence of proteinase K and Rhizopus arrhizus lipase by use of gravimetry. The addition of PLLA‐CL decreased the proteinase K–catalyzed hydrolyzabilities of the PLLA and PLLA/PCL (50/50) films as well as the Rhizopus arrhizus lipase‐catalyzed hydrolyzability of the PCL and PLLA/PCL (50/50) films. The decreased enzymatic hydrolyzabilities of the PLLA and PCL films upon addition of PLLA‐CL are attributable to the fact that the PLLA‐CL is miscible with PLLA and PCL and the dissolved PLLA‐CL must disturb the adsorption and/or scission processes of the enzymes. In addition to this effect, the decreased enzymatic hydrolyzabilities of the PLLA/PCL (50/50) films upon addition of PLLA‐CL can be explained by the enhanced compatibility between the PLLA‐rich and PCL‐rich phases arising from the dissolved PLLA‐CL. These effects result in decreased hydrolyzable interfacial area for PLLA/PCL films. The decrement in proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PLLA‐CL, which is miscible with PLLA, was in marked contrast with the enhanced proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PCL, which is immiscible with PLLA. This confirms that the miscibility of the second polymer is crucial to determine the proteinase K–catalyzed hydrolyzabilities of the PLLA‐based blend films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 412–419, 2003     

Synthesis of star‐shaped poly(ε‐caprolactone)‐b‐poly(L‐lactide) copolymers: From star architectures to crystalline morphologies

Hexa‐armed star‐shaped poly(ε‐caprolactone)‐block‐poly(L ‐lactide) (6sPCL‐b‐PLLA) with dipentaerythritol core were synthesized by a two‐step ring‐opening polymerization. GPC and ¹H NMR data demonstrate that the polymerization courses are under control. The molecular weight of 6sPCLs and 6sPCL‐b‐PLLAs increases with increasing molar ratio of monomer to initiator, and the molecular weight distribution is in the range of 1.03–1.10. The investigation of the melting and crystallization demonstrated that the values of crystallization temperature (T_c), melting temperature (T_m), and the degree of crystallinity (X_c) of PLLA blocks are increased with the chain length increase of PLLA in the 6sPCL‐b‐PLLA copolymers. On the contrary, the crystallization of PCL blocks dominates when the chain length of PLLA is too short. According to the results of polarized optical micrographs, both the spherulitic growth rate (G) and the spherulitic morphology are affected by the macromolecular architecture and the length of the block chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Enzymatic Degradation of Biodegradable Polyester Composites of Poly(L‐lactic acid) and Poly(ε‐caprolactone)

Summary: Two different types of biodegradable polyester composites, PLLA fiber‐reinforced PCL and PCL/PLLA blend films were prepared at PCL/PLLA ratio of 88/12 (w/w), together with pure PCL and PLLA films. Their enzymatic degradation was investigated by the use of Rhizopus arrhizus lipase and proteinase K as degradation enzymes for PCL and PLLA chains, respectively. In the FRP film, the presence of PLLA fibers accelerated the lipase‐catalyzed enzymatic degradation of PCL matrix compared with that in the pure PCL film, whereas in the blend film, the presence of PLLA chains dissolved in the continuous PCL‐rich domain retarded the lipase‐catalyzed enzymatic degradation of PCL chains. In contrast, in the FRP film, the proteinase K‐catalyzed enzymatic degradation of PLLA fibers was disturbed compared with that of the pure PLLA film, whereas in the blend film, the proteinase K‐catalyzed enzymatic degradation rate of particulate PLLA‐rich domains was higher than that of pure PLLA film. The reasons for aforementioned enhanced and disturbed enzymatic degradation are discussed.

Normalized PCL weight loss of pure PCL, FRP, and blend films as a function of Rhizopus arrhizus lipase‐catalyzed enzymatic degradation time.