Preparation and characterization of siliconized epoxy‐1,2‐bis(maleimido)ethane intercrosslinked matrix materials

Novel intercrosslinked networks of siliconized epoxy‐1,2‐bis(maleimido)ethane matrix systems are developed. The siliconization of epoxy resin is carried out by using 5–15% hydroxyl‐terminated poly(dimethylsiloxane) with γ‐aminopropyltriethoxysilane as a crosslinking agent and dibutyltin dilaurate as a catalyst. The siliconized epoxy systems are further modified with 5–15% 1,2‐bis(maleimido)ethane and cured by using diaminodiphenylmethane. The prepared neat resin castings are characterized for their mechanical properties. Mechanical studies indicate that the introduction of siloxane into these epoxy resins improves the toughness with a reduction in the stress–strain values, whereas incorporation of bismaleimide (BMI) into the epoxy resin improves the stress–strain properties with a lowering of the toughness. The introduction of both siloxane and BMI into the epoxy resin influences the mechanical properties according to their content percentages. Differential scanning calorimetry (DSC), thermogravimetry, and heat distortion temperature analyses are also carried out to assess the thermal behavior of the matrix materials that are developed. DSC thermograms of the BMI modified epoxy systems show unimodal reaction exotherms. The glass‐transition temperature, thermal degradation temperature, and heat distortion temperature of the cured BMI modified epoxy and siliconized epoxy systems increase with increasing BMI content. The water absorption behavior of the matrix materials is also studied. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3808–3817, 2003     

Studies on thermal and morphological behavior of siliconized epoxy bismaleimide matrices

Novel bismaleimide‐modified siliconized epoxy intercrosslinked network systems were developed. Siliconized epoxy systems containing 5, 10, and 15% siloxane units were prepared using epoxy resin and hydroxyl‐terminated polydimethylsiloxane (HTPDMS) with γ‐aminopropyltriethoxysilane (γ‐APS) as a compatibilizer and dibutyltindilaurate as a catalyst. The siliconized epoxy systems were further modified with 5, 10, and 15% (wt %) of bismaleimide [(N,N′‐bismaleimido‐4,4′‐diphenylmethane) (BMI)] and cured by diaminodiphenylmethane (DDM). Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and heat‐distortion temperature measurement of the matrix samples were carried out to assess their thermal behavior. DSC thermograms of the BMI‐modified epoxy systems show unimodel reaction exotherms. The glass transition temperature (T_g) of the cured BMI‐modified epoxy and siliconized epoxy systems increases with increasing BMI content. Thermogravimetric analysis and heat‐distortion temperature measurements indicate that the thermal degradation temperature and heat‐distortion temperature of the BMI‐modified epoxy and siliconized epoxy systems increase with increasing BMI content. The morphology of the BMI‐modified siliconized epoxy systems was also studied by scanning electron microscopy (SEM). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2330–2346, 2001     

Preparation and characterization of bismaleimide (N,N′‐bismaleimido‐4,4′‐diphenyl methane)–unsaturated polyester modified epoxy intercrosslinked matrices

An intercrosslinked network of unsaturated polyester–bismaleimide modified epoxy matrix systems was developed. Epoxy systems modified with 10, 20, and 30% (by weight) of unsaturated polyester were made by using epoxy resin and unsaturated polyester with benzoyl peroxide and diaminodiphenylmethane as curing agents. The reaction between unsaturated polyester and epoxy resin was confirmed by IR spectral studies. The unsaturated polyester toughened epoxy systems were further modified with 5, 10, and 15% (by weightt) of bismaleimide (BMI). The matrices, in the form of castings, were characterized for their mechanical properties. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) of the matrix samples were performed to determine the glass transition temperature (T_g) and thermal degradation temperature of the systems, respectively. Mechanical properties, viz: tensile strength, flexural strength, and plain strain fracture toughness of intercrosslinked epoxy systems, were studied by ASTM methods. Data obtained from mechanical and thermal studies indicated that the introduction of unsaturated polyester into epoxy resin improves toughness but with a reduction in glass transition, whereas the incorporation of bismaleimide into epoxy resin improved both mechanical strength and thermal behavior of epoxy resin. The introduction of bismaleimide into unsaturated polyester‐modified epoxy resin altered thermomechanical properties according to their percentage concentration. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2853–2861, 2002     

Preparation and characterization of 3,3′‐bis (maleimidophenyl)phenylphosphine oxide (BMI)/polysulfone modified epoxy intercrosslinked matrices

An intercrosslinked network of polysulfone (PSF)—bismaleimide (BMI) modified epoxy matrix system was made by using diglycidyl ether of bisphenol A (DGEBA) epoxy resin, hydroxyl terminated polysulfone and bismaleimide (3,3′‐bis(maleimidophenyl) phenylphosphine oxide) with diaminodiphenylmethane (DDM) as curing agent. BMI–PSF–epoxy matrices were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and heat deflection temperature (HDT) analysis. The matrices, in the form of castings, were characterized for their mechanical properties such as tensile strength, flexural strength, and unnotched Izod impact test as per ASTM methods. Mechanical studies indicated that the introduction of polysulfone into epoxy resin improves the toughness to an appreciable extent with insignificant increase in stress–strain properties. DSC studies indicated that the introduction of polysulfone decreases the glass transition temperature, whereas the incorporation of bismaleimide into epoxy resin influences the mechanical and thermal properties according to its percentage content. DSC thermograms of polysulfone as well as BMI modified epoxy resin show a unimodal reaction exotherm. The thermal stability and flame retardant properties of cured epoxy resins were improved with the introduction of bismaleimide and polysulfone. Water absorption characteristics were studied as per ASTM method and the morphology of the BMI modified epoxy and PSF‐epoxy systems were studied by scanning electron microscope. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Synthesis and characterization of siliconized epoxy-1,3-bis(maleimido)benzene intercrosslinked matrix materials

Intercrosslinked network of siliconized epoxy-1,3-bis(maleimido)benzene matrix systems have been developed. The siliconization of epoxy resin was carried out by using various percentages of (5-15%) hydroxyl-terminated polydimethylsiloxane (HTPDMS) with γ-aminopropyltriethoxysilane (γ-APS) as crosslinking agent and dibutyltindilaurate as catalyst. The siliconized epoxy systems were further modified with various percentages of (5-15%) 1,3-bis(maleimido)benzene (BMI) and cured by using diaminodiphenylmethane (DDM). The neat resin castings prepared were characterized for their mechanical properties. Mechanical studies indicate that the introduction of siloxane into epoxy resin improves the toughness of epoxy resin with reduction in the values of stress-strain properties whereas, incorporation of bismaleimide into epoxy resin improves stress-strain properties with lowering of toughness. However, the introduction of both siloxane and bismaleimide into epoxy resin influences the mechanical properties according to their percentage content. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and measurement of heat distortion temperature were also carried out to assess the thermal behavior of the matrix samples. DSC thermogram of the BMI modified epoxy systems show unimodel reaction exotherms. The glass transition temperature (T_g), thermal degradation temperature and heat distortion temperature of the cured BMI modified epoxy and siliconized epoxy systems increase with increasing BMI content and this may be due to the homopolymerization of BMI rather than Michael addition reaction. The morphology of the BMI modified epoxy and siliconized epoxy systems were also studied by scanning electron microscopy.     

Studies on mechanical,thermal, and morphology of diglycidylether‐terminated polydimethylsiloxane‐modified epoxy–bismaleimide matrices

An epoxy matrix system modified by diglycidylether‐terminated polydimethylsiloxane (DGETPDMS) and bismaleimide (BMI) was developed. Epoxy systems modified with 4, 8, and 12% (by wt) of DGETPDMS were made using epoxy resin and DGETPDMS, with diaminodiphenylmethane as the curing agent. The DGETPDMS‐toughened epoxy systems were further modified with 4, 8, and 12% (by wt) of BMI, namely (N,N′‐bismaleimido‐4,4′‐diphenylmethane). DGETPDMS/BMI/epoxy matrices were characterized using differential scanning calorimetry, thermogravimetric analysis, and heat deflection temperature analysis. The matrices, in the form of castings, were characterized for their mechanical properties, viz. tensile strength, flexural strength, and impact test, as per ASTM methods. Mechanical studies indicate that the introduction of DGETPDMS into epoxy resin improves the impact strength, with reduction in tensile strength, flexural strength, and glass transition temperature, whereas the incorporation of BMI into epoxy resin enhances the mechanical and thermal properties according to its percentage content. However, the introduction of both DGETPDMS and BMI enhances the values of thermomechanical properties according to their percentage content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 668–674, 2006     

Preparation and characterization of bismaleimide (N,N′‐bismaleimido‐4,4′‐diphenyl methane)–vinyl ester oligomer–modified unsaturated polyester interpenetrating matrices for advanced composites

Interpenetrating networks of varying percentages of bismaleimide (BMI) in vinyl ester oligomer (VEO) modified unsaturated polyester (UP) matrices have been developed. Vinyl ester oligomer was prepared by reacting commercially available epoxy resin GY 250 (Ciba‐Geigy) and acrylic acid, and used as a toughening agent for unsaturated polyester resin. Unsaturated polyesters modified with 10, 20, and 30 wt % vinyl ester oligomer were made. The VEO toughened unsaturated polyester matrix systems, further modified with 5, 10, and 15 wt % bismaleimide (BMI). BMI–VEO–UP matrices were characterized using differential scanning calorimetry, thermogravimetric analysis, and heat deflection temperature analysis. The matrices, in the form of castings, were characterized for their mechanical properties according to ASTM methods: tensile strength, flexural strength, and unnotched Izod impact test. Data obtained from mechanical studies and thermal characterization indicate that the introduction of VEO and BMI into unsaturated polyester resin improves thermomechanical properties according to their percentage concentration. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2502–2508, 2002     

Development and characterization of phosphorus-containing siliconized epoxy resin coatings

The objective of the present work is the development and characterization of siliconized epoxy-phosphorus based bismaleimide coating systems using diglycidylether terminated poly (dimethylsiloxane) (DGTPDMS) and phosphorus-containing bismaleimide (PBMI) as chemical modifiers for epoxy resin. Phosphorus-containing diamine (DOPO-NH₂) was synthesized from 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) and 4,4′-diaminobenzophenone (DABP), which was utilized in the preparation of phosphorus-containing bismaleimide (PBMI) with maleic anhydride. Siliconized epoxy prepolymer was prepared using epoxy resin and functionally terminated polydimethylsiloxane. The purity and structural conformation of these materials were ascertained from FTIR and NMR spectral studies. The prepared siliconized epoxy prepolymer was blended with varying percentages of PBMI using diaminodiphenylsulfone (DDS) and diaminodiphenylmethane (DDM) as curing agents. The siliconized epoxy and bismaleimide modified epoxy and siliconized epoxy coating materials were characterized by dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA), heat distortion temperature (HDT) and Limiting oxygen index (LOI).     

Mechanical properties of E‐glass fiber reinforced siliconized epoxy polymer composites

Siliconized epoxy‐matrix systems have been developed by an interpenetrating mechanism using epoxy resins GY 250 and LY 556 (Ciba‐Geigy) and hydroxyl terminated polydimethylsiloxane with γ‐aminopropyltriethoxysilane as crosslinker in the presence of dibutyltindilaurate catalyst. Aliphatic amine (HY 951, Ciba‐Geigy), aromatic amine (HT 972, Ciba‐Geigy) and polyamidoamine (HY 840, Ciba‐Geigy) are used as curing agents for epoxy resins. The tentative level of 10% siloxane introduction into epoxy resin has been ascertained from experimental studies to obtain reasonable improvements in the impact behavior without compromising other mechanical properties. The impact behavior of E‐glass reinforced composites made from the siliconized epoxy resin is enhanced to 2–4 times over that measured on the composites made from a pure epoxy resin. Composites cured with aromatic amine impart better mechanical properties than those cured with aliphatic amine and polyamidoamine.     

Mechanical and morphological properties of organic–inorganic,hybrid, clay‐filled,and cyanate ester/siloxane toughened epoxy nanocomposites

Organic–inorganic hybrids involving cyanate ester and hydroxyl‐terminated polydimethylsiloxane (HTPDMS) modified diglycidyl ether of bisphenol A (DGEBA; epoxy resin) filled with organomodified clay [montmorillonite (MMT)] nanocomposites were prepared via in situ polymerization and compared with unfilled‐clay macrocomposites. The epoxy‐organomodified MMT clay nanocomposites were prepared by the homogeneous dispersion of various percentages (1–5%), and the resulting homogeneous epoxy/clay hybrids were modified with 10% HTPDMS and γ‐aminopropyltriethoxysilane as a coupling agent in the presence of a tin catalyst. The siliconized epoxy/clay prepolymer was further modified separately with 10% of three different types of cyanate esters, namely, 4,4′‐dicyanato‐2,2′‐diphenylpropane, 1,1′‐bis(3‐methyl‐4‐cyanatophenyl) cyclohexane, and 1,3‐dicyanato benzene, and cured with diaminodiphenylmethane as a curing agent. The reactions during the curing process between the epoxy, siloxane, and cyanate were confirmed by Fourier transform infrared analysis. The results of dynamic mechanical analysis showed that the glass‐transition temperatures of the clay‐filled hybrid epoxy systems were lower than that of neat epoxy. The data obtained from mechanical studies implied that there was a significant improvement in the strength and modulus by the nanoscale reinforcement of organomodified MMT clay with the matrix resin. The morphologies of the siloxane‐containing, hybrid epoxy/clay systems showed heterogeneous character due to the partial incompatibility of HTPDMS. The exfoliation of the organoclay was ascertained from X‐ray diffraction patterns. The increase in the percentage of organomodified MMT clay up to 5 wt % led to a significant improvement in the mechanical properties and an insignificant decrease in the glass‐transition temperature versus the unfilled‐clay systems. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Toughened polyester matrices for advanced composites

An intercrosslinked network of hybrid bismaleimide (BMI) modified vinyl ester oligomer–unsaturated polyester matrix systems have been developed. Vinyl ester oligomer (VEO) was used as a toughening agent for unsaturated polyester resin and was added in 2, 4, and 6% (by wt). Benzoyl peroxide was used as curing agent. The VEO‐toughened unsaturated polyester matrix systems were further modified with 5, 10, and 15% (by wt) of bismaleimide. Bismaleimides modified vinyl ester–unsaturated polyester matrices were characterized by mechanical (tensile strength, flexural strength, tensile modulus, flexural modulus, and impact strength), thermal [differential scanning calorimetry (DSC), thermogravimetic analysis (TGA), heat deflection temperature analysis (HDT)] and morphological studies [scanning electron microscope (SEM)] and water absorption. Data obtained from mechanical studies indicated that the introduction of VEO into unsaturated polyester resin improves the fracture toughness. The introduction of BMI into VEO incorporated unsaturated polyester resin enhanced both thermal and mechanical behavior. The scanning electron micrographs of fractured surfaces of VEO‐modified unsaturated polyester systems and BMI modified vinyl ester–unsaturated polyester matrices illustrate the presence of homogeneous morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 167–177, 2007     

Preparation and properties of high performance phthalide‐containing bismaleimide modified epoxy matrices

A series of intercrosslinked networks formed by diglycidyl ether of bisphenol A epoxy resin (DGEBA) and novel bismaleimide containing phthalide cardo structure (BMIPP), with 4,4′‐diamino diphenyl sulfone (DDS) as hardener, have been investigated in detail. The curing behavior, thermal, mechanical and physical properties and compatibility of the blends were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), notched Izod impact test, scanning electron microscopy (SEM) and water absorption test. DSC investigations showed that the exothermic transition temperature (T_p) of the blend systems shifted slightly to the higher temperature with increasing BMIPP content and there appeared a shoulder on the high‐temperature side of the exothermic peak when BMIPP content was above 15 wt %. TGA and DMA results indicated that the introduction of BMIPP into epoxy resin improved the thermal stability and the storage modulus (G′) in the glassy region while glass transition temperature (T_g) decreased. Compared with the unmodified epoxy resin, there was a moderate increase in the fracture toughness for modified resins and the blend containing 5 wt % of BMIPP had the maximum of impact strength. SEM suggested the formation of homogeneous networks and rougher fracture surface with an increase in BMIPP content. In addition, the equilibrium water uptake of the modified resins was reduced as BMIPP content increased. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Curing behavior and thermal and mechanical properties enhancement of tetraglycidyl‐4,4′‐diaminodiphenylmethane/4,4′‐diaminodiphenylsulfone using a liquid crystalline epoxy

A thermosetting resin system, based on tetraglycidyl‐4,4′‐diaminodiphenylmethane, has been developed via copolymerization with 4,4′‐diaminodiphenylsulfone in the presence of a newly synthesized liquid crystalline epoxy (LCE). The curing behavior of LCE‐containing resin system was evaluated using curing kinetics method and Fourier transform infrared spectroscopy. The effect of LCE on the thermal and mechanical properties of modified epoxy systems was studied. Thermogravimetric analysis indicated that the modified resin systems displayed a high T_0.05 and char yield at lower concentrations of LCE (≤5 wt%), suggesting an improved thermal stability. As determined using dynamic mechanical analysis and differential scanning calorimetry, the glass transition value increased by 9.7% compared to that of the neat resin when the LCE content was 5 wt%. Meanwhile, the addition of 5 wt% of LCE maximized the toughness with a 175% increase in impact strength. The analysis of fracture surfaces revealed a possible effect of LCE as a toughener and showed no phase separation in the modified resin system, which was also confirmed by dynamic mechanical analysis. © 2016 Society of Chemical Industry     

Toughening of epoxy resin systems using low‐viscosity additives

This study has evaluated three low‐viscosity epoxy additives as potential tougheners for two epoxy resin systems. The systems used were a lower‐reactive resin based upon the diglycidyl ether of bisphenol A (DGEBA) and the amine hardener diethyltoluene diamine, while the second epoxy resin was based upon tetraglycidyl methylene dianiline (TGDDM) and a cycloaliphatic diamine hardener. The additives evaluated as potential tougheners were an epoxy‐terminated aliphatic polyester hyperbranched polymer, a carboxy‐terminated butadiene rubber and an aminopropyl‐terminated siloxane. This work has shown that epoxy‐terminated hyperbranched polyesters can be used effectively to toughen the lower cross‐linked epoxy resins, i.e. the DGEBA‐based systems, with the main advantage being that they have minimal effect upon processing parameters such as viscosity and the gel time, while improving the fracture properties by about 54 % at a level of 15 wt% of additive and little effect upon the T_g. This result was attributed to the phase‐separation process producing a multi‐phase particulate morphology able to initiate particle cavitation with little residual epoxy resin dissolved in the continuous epoxy matrix remaining after cure. The rubber additive was found to impart similar levels of toughness improvement but was achieved with a 10–20 °C decrease in the T_g and a 30 % increase in initial viscosity. The siloxane additive was found not to improve toughness at all for the DGEBA‐based resin system due to the poor dispersion within the epoxy matrix. The TGDDM‐based resin systems were found not to be toughened by any of the additives due to the lack of plastic deformation of the highly cross‐linked epoxy network Copyright © 2003 Society of Chemical Industry     

Cationic copolymerization of epoxy siloxane monomer with liquid poly‐butadiene and its light emitting diode encapsulation

A novel epoxy siloxane hybrid was prepared using epoxy siloxane monomers of 1,3‐bis[2‐(3‐{7‐oxabicyclo[4.1.0]heptyl})ethyl]‐tetramethyldisiloxane (BEPDS) with hydroxyl terminated hydrogenated polybutadiene (GI‐1000), in different proportions. Apparent polymerization reactivity was decreased with increasing GI‐1000 concentration but the normalized reactivity per epoxy group was slightly increased due to reaction between hydroxyl group and epoxy group. Increasing GI‐1000 concentration showed significant flexibility improvement in epoxy siloxane hybrid. At 30 wt % of GI‐1000 addition, glass transition temperature was decreased from 116 to 21°C and shore D hardness was decreased from 75 to 46.5% weight loss temperature of these epoxy siloxane hybrid was decreased with increasing GI‐1000 concentration, whereas thermal discoloration was increased. LED encapsulation with this epoxy siloxane demonstrated no crack when GI‐1000 was 30 wt % or more. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A comparative study on the preparation and characterization of aromatic and aliphatic bismaleimides‐modified polyurethane–epoxy interpenetrating polymer network matrices

Interpenetrating polymer networks of bismaleimide‐modified polyurethane–epoxy systems were prepared using the aliphatic and aromatic bismaleimides‐ and polyurethane‐modified epoxy and cured in the presence of 4,4′‐diaminodiphenylmethane. Infrared spectral analysis was used to confirm the polyurethane‐crosslinked epoxy (PU–EP). The matrices developed were characterized by mechanical, thermal, electrical, and morphological studies. The results obtained from the mechanical studies indicate that the incorporation of polyurethane and bismaleimides into epoxy increased the tensile strength, flexural strength, and impact strength, according to their nature and percentage concentration. The results obtained from the thermal and electrical studies indicate that the incorporation of polyurethane into epoxy decreased the thermal properties (glass transition temperature, heat distortion temperature (HDT), thermal stability) and electrical properties (dielectric strength, volume and surface resistivity, and arc resistance). The incorporation of aromatic bismaleimide into the polyurethane‐modified epoxy system increased the glass transition temperature, thermal stability, and electrical properties. Decreased values of glass transition and HDT were obtained in the case of aliphatic bismaleimide‐modified polyurethane–epoxy system. Surface morphology of modified epoxy systems was studied using scanning electron microscopy, and it was found that the polyurethane‐modified epoxy systems exhibited heterogeneous morphology and bismaleimides‐modified epoxy systems showed a homogeneous morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3592–3602, 2006     

Synthesis,formulation, and characterization of siloxane‐modified epoxy‐based anticorrosive paints

Diglycidyl ether of bisphenol A epoxy (E) was modified with hydroxyl‐terminated polydimethylsiloxane through a ring‐opening addition polymerization reaction. The structural elucidation of the siloxane‐modified epoxy resin (ES) was carried out with Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopy techniques. The physicochemical characterization of the synthesized resin (ES) was performed with standard methods. E and ES were subjected to paint formulation with the help of a rutile (TiO₂) pigment. The formulated paint systems were cured at room temperature with 1,6‐diaminohexane (AH) and 1,3‐diaminopropane (AP), which were used as curatives. The E–AH, E–AP, ES–AH, and ES–AP paint systems were applied to mild steel strips. The physicomechanical and anticorrosive performance of the coated panels was evaluated with standard methods. The thermal analysis of these E–amine and ES–amine systems was carried out via thermogravimetric analysis. The effects of siloxane incorporation and amine curatives on the coating properties of the paint systems were also investigated. The ES–AP system exhibited good thermal and corrosion stability performance among all the E and ES paint systems. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4981–4991, 2006     

Modification of bismaleimide resin by poly(ethylene phthalate‐co‐ethylene terephthalate), poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate), and poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)

Aromatic polyesters were prepared and used to improve the brittleness of bismaleimide resin, composed of 4,4′‐bismaleimidodiphenyl methane and o,o′‐diallyl bisphenol A (Matrimid 5292 A/B resin). The aromatic polyesters included PEPT [poly(ethylene phthalate‐co‐ethylene terephthalate)], with 50 mol % of terephthalate, PEPB [poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate)], with 50 mol % of 4,4′‐biphenyl dicarboxylate, and PEPN [poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)], with 50 mol % 2,6‐naphthalene dicarboxylate unit. The polyesters were effective modifiers for improving the brittleness of the bismaleimide resin. For example, inclusion of 15 wt % PEPT (MW = 9300) led to a 75% increase in fracture toughness, with retention in flexural properties and a slight loss of the glass‐transition temperature, compared with the mechanical and thermal properties of the unmodified cured bismaleimide resin. Microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The toughening mechanism was assessed as it related to the morphological and dynamic viscoelastic behaviors of the modified bismaleimide resin system. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2352–2367, 2001     

Effect of elastomer modification on the adhesive characteristics of maleimide‐functional phenolic resins

The effect of addition of elastomeric modifiers on the adhesive properties like lap shear strength and T‐peel strength of an addition curable, maleimide functional novolac phenolic resin (PMF), self‐cured and cocured with a novolac epoxy resin, was studied using aluminium adherends. The modifiers used were (1) two grades of carboxyl terminated butadiene acrylonitrile copolymer (CTBN) of different molecular weights, (2) a low molecular weight, epoxidized hydroxyl‐terminated polybutadiene, and (3) a high molecular weight acrylate terpolymer containing pendant epoxy functionality. The adhesive properties, when examined as a function of the varying concentrations of the additives, ranging from 10 to 30 parts per hundred parts (phr) of the resin, were found to depend on the nature of the matrix being modified as well as on the nature and concentration of the elastomer. The adhesive properties at ambient temperature of the self‐cured, highly brittle PMF resin were dramatically improved by the inclusion of all the elastomers, the increase being substantial in the case of high molecular weight CTBN. For the more rigid, less ductile, epoxy‐cured PMF system, the adhesive properties were marginally improved by the high molecular weight CTBN, whereas the other elastomers were practically ineffective. For both self‐cured and epoxy‐cured PMF systems, the inclusion of these elastomers generally decreased the high‐temperature adhesive properties, implying impairment of thermal characteristics, evidenced also from their dynamic mechanical spectra. The presence of phase‐separated elastomer particles in the modified systems has been evidenced from scanning electron micrographs. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2321–2332, 1999     

Thermal characterization of carbon‐nanofiber‐reinforced tetraglycidyl‐4,4′‐diaminodiphenylmethane/4,4′‐diaminodiphenylsulfone epoxy composites

The thermal properties of carbon nanofibers (CNF)/epoxy composites, composed of tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM) resin and 4,4′‐diaminodiphenylsulfone (DDS) as a curing agent, were investigated with differential scanning calorimetry (DSC), thermogravimetric analysis, and dynamic mechanical thermal analysis. DSC results showed that the presence of CNF had no pronounced influence on the heat of the cure reaction. However, the incorporation of CNF slightly improved the thermal stability of the epoxy. Furthermore, the storage modulus of the TGDDM/DDS epoxy was significantly enhanced, whereas the glass‐transition temperature was not significantly affected, upon the incorporation of CNFs. The storage modulus of 5 wt % CNF/epoxy composites at 25°C was increased by 35% in comparison with that of the pure epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 295–298, 2006