Effect of the high‐density polyethylene melt index on the microcellular foaming of high‐density polyethylene/polypropylene blends

The effect of high‐density polyethylene (HDPE)/polypropylene (PP) blending on the crystallinity as a function of the HDPE melt index was studied. The melting temperature and total amount of crystallinity in the HDPE/PP blends were lower than those of the pure polymers, regardless of the blend composition and melt index. The effects of the melt index, blending, and foaming conditions (foaming temperature and foaming time) on the void fractions of HDPEs of various melt indices and HDPE/PP blends were also investigated. The void fraction was strongly dependent on the foaming time, foaming temperature, and blend composition as well as the melt index of HDPE. The void fraction of the foamed 30:70 HDPE/PP blend was always higher than that of the foamed 50:50 HDPE/PP blend, regardless of the melt index. The microcellular structure could be greatly improved with a suitable ratio of HDPE to PP and with foaming above the melting temperature for long enough; however, using high‐melt‐index HDPE in the HDPE/PP blends had a deleterious effect on both the void fraction and cell morphology of the blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 364–371, 2004     

Development of isotropic compatible HDPE/PP blends for structural applications

In an attempt to provide superior products for the structural applications, this study aimed at preparing isotropic compatible high density polyethylene (HDPE)/ polypropylene (PP) blends without the use of the expensive compatibilization technique. Morphological and structural characterizations of the homopolymers and blends were carried out. In addition, some of the structurally important mechanical and thermal properties were characterized. Such characterizations were performed to investigate whether or not the blends are compatible and therefore acceptable for the structural applications. Scanning electron microscope (SEM) micrographs of the blend samples indicate that the interfacial adhesion between HDPE and PP phases is intimate in the 5/95 HDPE‐PP, good in the 85/15 HDPE‐PP and 95/5 HDPE‐PP, fair in the 30/70 HDPE‐PP and very poor in the 50/50 HDPE‐PP. Similarly, mechanical and thermal responses of the first three blends are remarkable. The 30/70 HDPE‐PP blend displays a fairly good performance. Whereas, the properties of the 50/50 HDPE‐PP blend are very poor. This decides that the first three blends are compatible and, therefore, structurally attractive materials. The fourth is partially compatible and, as a consequence, can be rather acceptable for the structural applications. However, the fifth is incompatible and, of course, is not acceptable for such applications. On the other hand, SEM micrographs and differential scanning calorimetry results indicate that the crystalline structures of individual polymers are appreciably affected by blending. Additionally, the study reveals that the end use performance of blends is strongly dependent on the crystalline structure changes occurring in each component due to blending as well as the compatibility between the blend components. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Study on processing of ultrahigh molecular weight polyethylene/polypropylene blends

The processing of ultrahigh molecular weight polyethylene (UHMWPE) by the addition of polypropylene (PP) and high‐density polyethylene (HDPE) was investigated. The results show that the addition of PP improves the processability of UHMWPE more effectively than does the addition of HDPE. UHMWPE/PP blends can be effectively processed with a twin‐roller and general single‐screw extruder. In the extrusion of UHMWPE/PP blends, PP is enriched at the surface of the blend adjacent to the barrel wall, thus increasing the frictional force on the wall; the conveyance of the solid down to the channel can then be carried out. The melt pool against the active flight flank exerts a considerable pressure on the UHMWPE powder in the passive flight flank, which overcomes the hard compaction of UHMWPE. The PP penetrates into the gaps between the particles, acting as a heat‐transfer agent and adhesive, thus enhancing the heat‐transfer ability in the material. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 977–985, 2004     

Recycled car bumpers' impact resistance investigated by wide‐angle X‐ray diffraction

The recycled polyolefinic product from discarded standard car bumpers collected from Rio de Janeiro suburb shops was characterized by mechanical and wide‐angle X‐ray scattering (WAXS) methods. We found that the recycled plastic mixture is composed mainly of polypropylene (PP), containing ethylene‐propylene‐diene (EPDM) terpolymers and a minor proportion of high‐density polyethylene (HDPE), and is highly resistant to impact. The results were compared with the corresponding data obtained from binary and ternary blends of virgin PP, EPDM, and HDPE. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 999–1004, 2000     

Relationship between cell morphology and impact strength of microcellular foamed high‐density polyethylene/polypropylene blends

Polymer blends, such as those resulting from recycling postconsumer plastics, often have poor mechanical properties. Microcellular foams have been shown to have the potential to improve properties, and permit higher‐value uses of mixed polymer streams. In this study, the effects of microcellular batch processing conditions (foaming time and temperature) and HDPE/PP blend compositions on the cell morphology (the average cell size and cell‐population density) and impact strength were studied. Optical microscopy was used to investigate the miscibility and crystalline morphology of the HDPE/PP blends. Pure HDPE and PP did not foam well at any processing conditions. Blending facilitated the formation of microcellular structures in polyolefins because of the poorly bonded interfaces of immiscible HDPE/PP blends, which favored cell nucleation. The experimental results indicated that well‐developed microcellular structures are produced in HDPE/PP blends at ratios of 50:50 and 30:70. The cell morphology had a strong relationship with the impact strength of foamed samples. Improvement in impact strength was associated with well‐developed microcellular morphology. Polym. Eng. Sci. 44:1551–1560, 2004. © 2004 Society of Plastics Engineers.     

Study of the mechanical,thermal, and thermodegradative properties of virgin PP with recycled and non-recycled HDPE

In order to show the significance of plastic recycling, a study of the properties of blends of PP with non-recycled and recycled high density polyethylene (HDPE) is made. The results of the Young's modulus for polypropylene (PP)/non-recycled and recycled HDPE blends present a slight synergism, although no significant dependence of this property on the compound was observed. The values of elongation at break and impact strength reflect the incompatibility of the blends. In thermal studies of the blends, the values of fusion enthalpy are below the values of the components. The results of the thermodegradative studies show that activation energies (E_a) obtained are lower, in the case of the blends, than the E_a corresponding to pure polymers. In PP/recycled HDPE blends, activation energy, at 5% to 20% concentration, is maintained and falls abruptly with an increase in the concentration of the recycled material. Based upon the facts previously exposed, it is possible to recycle the recycled HDPE up to 20% concentration, in PP blends. The addition of the compatibilizer at 5% represents the optimal concentration for improving the final properties of the finished product.     

Improving polypropylene microcellular foaming through blending and the addition of nano‐calcium carbonate

This article reports an attempt to improve polypropylene (PP) microcellular foaming through the blending of PP with high‐density polyethylene (HDPE) as a minor component and the incorporation of nano‐calcium carbonate (nano‐CaCO₃) into PP and its blends with HDPE. Three HDPEs were selected to form three blends with a viscosity ratio less than, close to, or greater than unity. Two concentrations of nano‐CaCO₃, 5 and 20 wt %, were used. The blends and nanocomposites were prepared with a twin‐screw extruder. The foaming was carried out by a batch process with supercritical carbon dioxide as a blowing agent. The online shear viscosity during compounding and the dynamic rheological properties of some samples used for foaming were measured. The cell structure of the foams was examined with scanning electron microscopy (SEM), and the morphological parameters of some foams were calculated from SEM micrographs. The rheological properties of samples were used to explain the resulting cell structure. The results showed that the blend with a viscosity ratio close to unity produced a microcellular foam with the minimum mean cell diameter (0.7 μm) and maximum cell density (1.17 × 10¹¹ cells/cm³) among the three blends. A foamed PP/nano‐CaCO₃ composite with 5 wt % nano‐CaCO₃ exhibited the largest cell density (8.4 × 10¹¹ cells/cm³). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Recycling of commingled plastics waste containing polypropylene,polyethylene, and paper

Polymer waste recycling is a major technical problem, because large amounts of synthetic polymers are produced every day and polymeric wastes are gathered from municipal solid wastes. There are a few polyolefins, such as polyethylene (PE) and polypropylene (PP) with huge amounts of paper in the waste materials. In order to recycle the commingled plastics waste that contains paper, hydrolytic treatment is needed prior to conventional processing. In this project, the optimum conditions of hydrolytic treatment of paper and the mechanical properties and morphological state of different compositions of PP high‐density PE (HDPE) blends with paper were studied. Ethylene‐propylene‐diene copolymer (EPDM) was added to improve the mechanical properties of blends. The results show that the hydrolytic treatment of paper improves the mechanical properties, such as the tensile strength and modulus of the PP/HDPE/paper composites relative to the untreated samples, and up to 30% paper can be added to commingled PP and HDPE blends. The EPDM was used as an impact modifier. The plastics waste containing paper can be used in applications such as artificial wood. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2573–2577, 2001     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effects of dispersed phase composition on thermoplastic polyolefins

Ternary blends of polypropylene (PP), ethylene–octene copolymer (mPE), and high‐density polyethylene (HDPE) were prepared based on the phase behavior and physical properties of mPE/HDPE binary blends, and the results were interpreted in terms of morphology and both rheological and mechanical properties of the ternary blends as well as the binary blends. It was found that when mPE encapsulates HDPE in the PP matrix, compared to the encapsulation of mPE by HDPE, better blend properties were obtained, presumably because of the compatibilizing effect of mPE between PP and HDPE. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 179–188, 2004     

Crystallization behaviors of polypropylene and functional polypropylene

The crystallization behaviors of polypropylene (PP) homopolymer and its blends with 0–15% functional polypropylene (FPP), the backbones of which were grafted with guanidine and diamide polymer chains, were investigated with differential scanning calorimetry and wide‐angle X‐ray scattering. The crystallization kinetics were studied with spectral depolarization. The results revealed that the presence of FPP reduced the crystallinity and crystallite size of PP. Meanwhile, FPP increased the crystallization rate. Compared with that of the PP homopolymer, the crystallization temperature of PP/FPP blends was increased by more than 10°C. During isothermal crystallization, the relative crystallinity, developed as a function of time, was described by the Avrami equation. The half‐time of crystallization for PP/FPP blends was much shorter than that for the PP homopolymer. The half‐time of crystallization of PP/FPP blends depended much less on the crystallization temperature than that of the PP homopolymer. Therefore, FPP accelerated the crystallization rate of PP in a manner similar to that of a nucleator. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 872–877, 2003     

Characterization of the free volume in high‐impact polystyrene/polypropylene and high‐impact polystyrene/high‐density polyethylene blends probed by positron annihilation spectroscopy

The free‐volume properties of high‐impact polystyrene (HIPS)/polypropylene (PP) and HIPS/high‐density polyethylene (HDPE) blends were investigated by means of positron annihilation lifetime spectroscopy (PALS). The measured results show that the free‐volume holes in the semicrystalline polymers, such as PP and HDPE, were not large enough to accommodate the branched chains and the end groups of the macromolecular chains in HIPS to produce favorable interactions between the semicrystalline polymers and the HIPS polymer in these blends; thus immiscible blends were formed. The weak interaction between two dissimilar polymer molecules only took place in the regions between two amorphous phases. In addition, the observed negative deviations of the longest lifetime intensity and the free‐volume fraction were attributed to the influence of the interfacial polarization during PALS measurement. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1507–1514, 2003     

浮沉分离法回收HDPE/PP混合物的研究

用自行设计的分离器,以浮沉法分离了回收塑料瓶盖中的高密度聚乙烯(HDPE)和聚丙烯(PP)。研究了混合塑料中HDPE和PP的含量、回收塑料尺寸以及分离液密度等因素对分离效果的影响。结果表明:分离后得到的产物中HDPE和PP的纯度可达到97%以上。     

Structure and properties of polypropylene/high‐density polyethylene blends by solid equal channel angular extrusion

The solid equal channel angular extrusion (ECAE) process on polypropylene (PP)/high‐density polyethylene (HDPE) blends was carried out. Scanning electron microscopy (SEM) was used to observe the sample structures. Results showed that ECAE process could make PP/HDPE blends to produce orientation structure. Impact performance of ECAE‐PP/HDPE samples after ECAE process improved remarkably, especially for ECAE‐PP/HDPE (90/10)‐O whose impact strength reached 91.91 kJ/m², 18.1 times higher than that of pure PP and 11.2 times higher than that of PP/HDPE (90/10). The mechanism of enhancing between HDPE and PP was discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39759.     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

Morphology and mechanical properties of biaxially oriented films of polypropylene and HDPE blends

Biaxially oriented films of blends of high-density polyethylene (HDPE) with polypropylene (PP) homopolymer and PP copolymers prepared by twin-screw extrusion and lab-stretcher have been investigated by scanning electron microscopy (SEM), polarized microscopy, differential-scanning calorimeter, and universal testing machine. Three different kinds of PP copolymers were used: (i) ethylene–propylene (EP) random copolymer; (ii) ethylene–propylene (EP) block copolymer; (iii) ethylene–propylene–buttylene (EPB) terpolymer. In the SEM study of the morphology of films of HDPE with various PP blends, phase separation is observed between the PP phase and the HDPE phase for all blends and compositions. In all blends, HDPE serves to reduce the average spherulites size, probably acting as a nucleating agent for PP. The reduction of spherulite size appeared most significantly in the blend of EPB terpolymer and HDPE. A large increase of crystallization temperature was found in the blend of EPB terpolymer and HDPE compared with the unblended EPB terpolymer. For the blend of EPB terpolymer and HDPE, the improvement of tensile strength and modulus is observed with an increase of HDPE content, and this can be considered as a result of the role of HDPE in reducing average spherulite size. © 1994 John Wiley & Sons, Inc.     

Studies on binary and ternary blends of polypropylene with SEBS,PS, and HDPE. II. Tensile and impact properties

Studies are reported on tensile and impact properties of several binary and ternary blends of polypropylene (PP), styrene-b-ethylene-co-butylene-b-styrene triblock copolymer (SEBS), high-density polyethylene (HDPE), and polystyrene (PS). The blend compositions of the binary blends PP/X were 10 wt % X and 90 wt % PP, while those of the ternary blends PP/X/Y were 10 wt % of X and 90 wt % of PP/Y, or 10 wt % Y and 90 wt % PP/X (PP/Y and PP/X were of identical composition 90:10); X, Y being SEBS, HDPE, or PS. The results are interpreted for the effect of each individual component by comparing the binary blends with the reference system PP, and the ternary blends with the respective binary blends as the reference systems. The ternary blend PP/SEBS/HDPE showed properties distinctly superior to those of PP/SEBS/PS or the binary blends PP/SEBS and PP/HDPE. Differences in the tensile yield behavior of the different samples and their correlation with impact strength suggested shear yielding as the possible mechanism of enhancement of impact strength. Scanning electron microscopic study of the impact fractured surfaces also supports the shear yielding mechanism of impact toughening of these blends.     

Compatibility of HDPE/postconsumer HDPE blends using compatibilizing agents

Mechanical properties, molecular weight, X‐ray diffraction, and differential scanning calorimetry (DSC) characterization of blends of virgin high‐density polyethylene (HDPE) with two types of recycled material were investigated. The recycled came from urban plastic waste; one kind was only washed and grounded and the other was extruded and pelletized to remove most of contaminant particles. Starting with the 30/70 virgin/grounded recycled and 50/50 virgin/pelletized recycled blends the recycled content was increased in both blends and compatibilizing agents were used to increase the blend performance. A mixture of phenolic antioxidants and phosphite costabilizers under the name of Recycloblend?, ethylene vinyl acetate (EVA) copolymer, low‐density polyethylene (LDPE), and linear low density polyethylene (LLDPE) were used as compatibilizers. The effect of these additives and the recycled content on the performance of extrusion blow‐molded bottles was determined. The results suggest that blends of virgin/grounded recycled and virgin/pelletized recycled HDPE, in general, were not significantly different among each other and both had a quite similar behavior than the virgin HDPE when compatibilizing agents were used. The addition of compatibilizing agents yielded a material with properties similar to those for the virgin HDPE, helping to reduce the effect of polymers degradation on the rheological and mechanical behavior, with Recycloblend and LLDPE being the most effective for the blends with grounded recycled material, and LLDPE y EVA, for the blends with pelletized recycled. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3696–3706, 2006     

A comparative study of polypropylene/(chloroprene rubber) and (recycled polypropylene)/(chloroprene rubber) blends

The blends of virgin polypropylene (PP) and recycled polypropylene (RPP) with chloroprene rubber (CR) have been prepared. The effect of different blend ratios on tensile properties, swelling behavior, morphology, and crystallinity of both blends of virgin and RPP was investigated. The tensile strength and Young's modulus of both blends decreased with increasing CR in blend ratios but the elongation at break was increased. It was found that the tensile properties of PP/CR blends were better than the RPP/CR blends. The PP/CR blends showed the lower value of swelling index. The scanning electron micrograph of the tensile fractured surface of PP/CR blends indicates that a higher energy is needed to cause failure compared with RPP/CR blends. The differential scanning calorimery results indicated that the degree of crystallinity of PP/CR blends also was found to be higher than RPP/CR blends. J. VINYL ADDIT. TECHNOL., 21:122–127, 2015. © 2014 Society of Plastics Engineers     

Processing and properties of recycled polypropylene modified with elastomers

Abstract

This work presents a study of the processability and the characterisation of blends of recycled polypropylene (PP) with two different elastomers. The aim of the work was to demonstrate that the introduction of an elastomeric phase could improve the properties of recycled PP without changing the processing characteristics of the blends in terms of viscosity and temperature. The study was carried out using thermal analysis, thermomechanical analysis and rheological measurements. The rheological analysis of blends of recycled PP and elastomeric additives showed that, despite the different rheological behaviour of the added elastomers, the properties of the blends were dominated by the thermoplastic (PP) phase. A thermogravimetric analysis of the selected blends allowed the calculation of the parameters related to the thermal degradation of such materials and the main results indicated that there were no significant differences between virgin and recycled PP in terms of behaviour at high temperatures. Furthermore, the blending of recycled PP with elastomers did not result in a significant change in thermal degradation behaviour. Crystallisation studies showed that blending polypropylene with elastomers influenced the rate and amount of crystallisation, which increased at low additive concentrations and then decreased at a higher elastomer content. Thermomechanical analysis showed the immiscible character of the blends. The mechanical properties of the blends were affected by the concentration of elastomer, which also influenced the crystallinity of the material.