Molecular structures and physical properties of heat‐drawn conjugate fibers

As‐spun poly(trimethylene terephthalate) (PTT)/poly(ethylene terephthalate) (PET) side‐by‐side conjugate fibers were drawn to investigate the effects of drawing conditions on structure development and physical properties. Effects of draw ratio and heat‐set temperature were observed. In the state of an as‐spun fiber, the molecular orientation of PTT was higher than PET, whereas PET molecular orientation increased remarkably over PTT with increasing draw ratio. Crimp contraction increased sharply at a draw ratio over 2.0, where the crystalline structure of the PET developed sufficiently. A heat‐set temperature of at least 140°C was required to develop sufficient crimp contraction. The crystallinity and orientation of the PET were attributed mainly to the crimp contraction of the drawn fiber. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Investigations of the preparation technology for polyglycolic acid fiber with perfect mechanical performance

Polyglycolic acid (PGA) fibers were prepared by melt‐spinning process in this report. The effects of spinning parameters, such as windup rates and drawn ratio, on the mechanical properties of the fibers were discussed by analyzing the internal stress of as‐spun fibers, axial sound velocity, fiber tenacity, etc. The results showed that windup rate had a slight effect on the macromolecular orientation degree of the as‐spun fibers, which was quite unusual for melt spinning, whereas, the subsequent drawing process effectively increased the macromolecular orientation degree of the PGA fibers and consequently increased the tensile strength of the fibers. Low internal stress of as‐spun fibers obtained at lower windup rate led to higher drawing ratio, and the drawn fibers possessed relatively excellent mechanical properties. As a contrast, higher windup rate resulted in the strong internal stress of the as‐spun fibers, which had a negative influence on the drawing process, and so the tensile strength of the drawn fibers was relatively poor. Therefore, PGA fiber with perfect mechanical performance could be prepared at the technical parameters of lower windup rate and higher drawing multiples as well as slow drawing rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effects of spinning and drawing conditions on the crimp contraction of side‐by‐side poly(trimethylene terephthalate) bicomponent fibers

The crimp properties in the melt‐spinning and drawing processes of side‐by‐side bicomponent fibers with poly(trimethylene terephthalate)s (PTTs) of different viscosities were studied. Two PTTs of different intrinsic viscosities (1.02 and 0.92) were selected to make latent crimp yarn. The spinning and drawing conditions were changed to investigate the relation between the process conditions and crimp contraction. An orthogonal array was used to rule out the weak variables. The draw ratio, heat‐set temperature, and portion of high‐viscosity PTT were selected as variables having an effect on the crimp contraction. An analysis of the effects of the spinning and drawing conditions on the crimp contraction showed that the draw ratio was the most critical variable. Increasing the draw ratio caused a difference in the shrinkage between the two parts of PTT and caused the self‐crimping of the bicomponent fibers. Although changing the heat‐set temperature and the portion of high‐viscosity PTT did not produce a dimensional change, the crimp contraction varied with those variables. As the heat‐set temperature and the high‐viscosity portion increased, the crimp contraction increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1322–1327, 2006     

Investigation on dry spinning process of ultrahigh molecular weight polyethylene/decalin solution

The relationship between the draw‐down ratio in the dry spinning process of ultrahigh molecular weight polyethylene/decalin solution and the fiber performance through maximized after‐drawing was investigated. The structural development during the after‐drawing process was analyzed by scanning electron microscopy, differential scanning calorimetry, wide‐angle X‐ray diffraction, sonic velocity, and FTIR measurements. An optimum draw‐down ratio was found in the multihole dry spinning process, which may be explained by molecular disentanglement and the composite effect of entropy and the viscosity component. The as‐spun fiber by draw‐down had an obvious shish kebab morphology, lower crystallinity, and a higher melting temperature compared with a free extrusion sample, and higher crystallinity and melting temperature compared with the fiber by first‐stage after‐drawing. During the subsequent after‐drawing process, the crystallinity, melting temperature, X‐ray diffraction, and sonic velocity orientation factors increased slowly in the higher after‐drawing ratio region, which was not consistent with the rising tendency of the tensile properties. The polarized and unpolarized IR spectra reflected the variations of the orientation and the content of the folded chains. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 474–483, 2005     

Preparation of poly(lactic acid) fiber by dry–jet–wet spinning. II. Effect of process parameters on fiber properties

The dry–jet–wet spinning process was employed to spin poly(lactic acid)(PLA) fiber by the phase inversion technique using chloroform and methanol as solvent and nonsolvent, respectively, for PLA. The as spun fiber was subjected to two‐stage hot drawing to study the effect of various process parameters, such as take‐up speed, drawing temperature, and heat‐setting temperature on the fiber structural properties. The take‐up speed had a pronounced influence on the maximum draw ratio of the fiber. The optimum drawing temperature was observed to be 90°C to get a fiber with the tenacity of 0.6 GPa for the draw ratio of 8. The heat‐setting temperature had a pronounced effect on fiber properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3774–3780, 2006     

Spinning and drawing properties of ultrahigh‐molecular‐weight polyethylene fibers prepared at varying concentrations and temperatures

The concentrations and temperatures of ultrahigh‐molecular‐weight polyethylene (UHMWPE) gel solutions exhibited a significant influence on their rheological and spinning properties. The shear viscosities of UHMWPE solutions increased consistently with increasing concentrations at a constant temperature above 80°C. Tremendously high shear viscosities of UHMWPE gel solutions were found as the temperatures reached 120–140°C, at which their shear viscosity values approached the maximum. The spinnable solutions are those gel solutions with optimum shear viscosities and relatively good homogeneity in nature. Moreover, the gel solution concentrations and spinning temperatures exhibited a significant influence on the drawability and microstructure of the as‐spun fibers. At each spinning temperature, the achievable draw ratios obtained for as‐spun fibers prepared near the optimum concentration are significantly higher than those of as‐spun fibers prepared at other concentrations. The critical draw ratio of the as‐spun fiber prepared at the optimum concentration approached a maximum value, as the spinning temperature reached the optimum value of 150°C. Further investigations indicated that the best orientation of the precursors of shish‐kebab‐like entities, birefringence, crystallinity, thermal and tensile properties were always accompanied with the as‐spun fiber prepared at the optimum concentration and temperature. Similar to those found for the as‐spun fibers, the birefringence and tensile properties of the draw fibers prepared at the optimum condition were always higher than those of drawn fibers prepared at other conditions but stretched to the same draw ratio. Possible mechanisms accounting for these interesting phenomena are proposed.     

High modulus polypropylene fibers. II. Influence of fiber preparation upon structure and morphology

The influence of drawing on the limiting draw ratio upon formation of the morphological structure of fibers spun from binary polypropylene (PP) blends was studied. Fibers were spun from a fiber‐grade CR‐polymer and from the blends of a fiber‐grade CR‐polymer with a molding‐grade polymer in the composition range of 10–50 wt % added. As‐spun fibers were immediately moderately and additionally highly drawn at the temperature of 145°C. The structure and morphology of these fibers were investigated by small‐angle X‐ray scattering, wide‐angle X‐ray scattering, differential scanning calorimetry, scanning electron microscopy, density, birefringence, and sound velocity measurements. It was shown that continuously moderately drawn fibers are suitable precursors for the production of high tenacity PP fibers of very high modulus, because of so called oriented “smectic” structure present in these fibers. With drawing at elevated temperature, the initial metastable structure of low crystallinity was disrupted and a c‐axis orientation of monoclinic crystalline modification was developed. Hot drawing increased the size of crystallites and crystallinity degree, the orientation of crystalline domains, and average orientation of the macromolecular chains and resulted in extensive fibrillation and void formation. It was found that the blend composition has some influence on the structure of discontinuously highly drawn fibers. With increasing the content of the molding‐grade polymer in the blend, the size of crystalline and amorphous domains, density and crystallinity, as well as amorphous orientation decreased. Relationship has been established between the mechanical properties, crystallinity, and orientation of PP fibers. It was confirmed that by blending the fiber‐grade CR‐polymer by a small percentage of the molding‐grade polymer, maximization of elastic modulus is achieved, mainly because of higher orientation of amorphous domains. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1067–1082, 2006     

Preparation of poly(lactic acid) fiber by dry‐jet‐wet‐spinning. I. Influence of draw ratio on fiber properties

Poly(lactic acid) fiber was prepared by dry‐jet‐wet spinning of the polymer from chloroform solution and with methanol as the precipitating medium. The as‐spun fiber was subsequently made into high strength fiber by two‐step process of drawing at a temperature of 90°C and subsequent heat setting in the temperature range of 120°C. The draw ratio had significant influence on the crystallinity and the tensile strength of the fiber. The fiber with the tenacity of 0.6 GPa and modulus of 8.2 GPa was achieved at a draw ratio of 8. The differential scanning calorimetry revealed an increase in the glass‐transition temperature with the increase in the draw ratio, which suggests the orientation of chains during the drawing process. The surface morphology of the filament as revealed by scanning electron microscopy shows that fibers are porous in nature, but a significant reduction in the porosity and pore size of the fiber was observed with the increase in the draw ratio. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1239–1246, 2006     

Mechanical properties and microstructure of poly(ethylene terephthalate) microfiber prepared by carbon dioxide laser heating

We determined that a poly(ethylene terephthalate) microfiber was easily obtained by irradiating a carbon dioxide laser to an annealed fiber. The annealed fiber was prepared by zone drawing and zone annealing. First, an original fiber was zone drawn at a drawing temperature of 90°C under an applied tension of 4.9 MPa, and the zone‐drawn fiber was subsequently zone annealed at 150°C under 50.9 MPa. The zone‐annealed fiber had a degree of crystallinity of 48%, a birefringence of 218.9 × 10^?3, tensile modulus of 18.8 GPa, and tensile strength of 0.88 GPa. The microfiber prepared by laser heating the zone‐annealed fiber had a diameter of 1.5 μm, birefringence of 172.8 × 10^?3, tensile modulus of 17.6 GPa, and tensile strength of 1.01 GPa. The draw ratio estimated from the diameter was 9165 times; such a high draw ratio has thus far not been achievable by any conventional drawing method. Microfibers may be made more easily by laser heating than by conventional technologies such as conjugate spinning. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1955–1958, 2003     

PBT/PET conjugated fibers: Melt spinning,fiber properties,and thermal bonding

This work examines the PBT/PET sheath/core conjugated fiber, with reference to melt spinning, fiber properties and thermal bonding. Regarding the rheological behaviors in the conjugated spinning, PET and PBT show the smallest difference between their melt‐viscosity at temperatures of 290°C and 260°C respectively, which has been thought to represent optimal spinning conditions. The effect of processing parameters on the crystallinity of core material‐PET was observed and listed. In order of importance, these factors are the draw ratio, the heat‐set temperature, and the drawing temperature. The crystallinity of sheath material‐PBT, however, can be considered to be constant, independent of any processing parameters. The bulk orientation, rather than the crystallinity of PET core, dominates the tenacity of PBT/PET sheath/core fiber. Moreover, heat‐set treatment after drawing is recommended to yield a highly oriented conjugated fiber. With respect to thermal bonding, PBT/PET conjugated fibers processed via high draw ratio but low‐temperature heat setting can form optimal thermal bonds at a constant bonding temperature of 10°C above the T_m of PBT.     

Morphology and structure changes of aromatic copolysulfonamide fibers heat‐drawn at various temperatures

Pre‐drawn aromatic copolysulfonamide (co‐PSA) fibers were prepared by wet spinning and then heat drawing at temperatures varying from 350 to 390 °C, which are below the decomposition temperature. The fibers were then characterized using tensile testing, dynamic mechanical analysis, wide‐angle X‐ray diffraction and small‐angle X‐ray scattering. The relationship between structure and properties of the co‐PSA fibers drawn at different temperatures was investigated. The heat‐drawn co‐PSA fibers displayed similar glass transition temperature of about 355 °C, which was higher than that of pre‐drawn co‐PSA fibers of 345 °C. The crystal orientation was high as a crystalline structure formed during heat drawing and the crystallinity increased with the heat‐drawing temperature. However, the tenacity of the co‐PSA fibers did not increase linearly with the draw temperature. When the drawing temperature was higher than the glass transition temperature, a decrease in tenacity was observed, which could be attributed to an increase of crystallite size of the (100) plane and a decrease of the long period of the lamellar structure. © 2014 Society of Chemical Industry     

Melt spinning of β‐phase poly(vinylidene fluoride) yarns with and without a conductive core

When poly(vinylidene fluoride) (PVDF) is to be used as a piezoelectric material, the processing must include the formation of polar β‐phase crystallites, as well as the application of electrically conducting charge collectors, that is, electrodes. In this article, results from the melt spinning of PVDF yarns and a novel bicomponent PVDF‐yarn with a conductive carbon black/polypropylene (CB/PP) core are presented. Melt spinning has been done under conditions typical for industrial large‐scale fiber production. The effects on the resulting crystalline structure of varying the spinning velocity, draw rate, and draw temperature are discussed. The results show that, for maximum α‐to‐β phase transformation, cold drawing should take place at a temperature between 70 and 90°C, and both the draw ratio and the draw rate should be as high as possible. It was observed that the cold drawing necessary to form β‐phase crystallinity simultaneously leads to a decrease in the core conductivity of the bicomponent yarns. In this work, the melt spinning of bicomponent fibers with high‐β‐phase PVDF in the sheath and a CB/PP core was successfully accomplished. The core material remained electrically conductive, paving the way for the use of a CB‐polymer compound as inner electrode in the melt spinning of piezoelectric bicomponent fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Isotactic polypropylene microfiber prepared by carbon dioxide laser‐heating

An isotactic polypropylene (i‐PP) microfiber was obtained by irradiating a carbon dioxide laser to previously drawn fibers. To prepare the thinner i‐PP microfiber, it is necessary to previously draw original i‐PP fibers under an applied tension of 7.8 MPa at a drawing temperature of 140°C. The drawn fiber was heated under an applied tension of 0.3 MPa using the laser operated at a power density of 39.6 W cm^?2. The thinnest i‐PP microfiber obtained under optimum conditions had a diameter of 1.8 μm and a birefringence of 30 × 10^?3. Its draw ratio estimated from the diameter reached 51,630. It is so far impossible to achieve such a high draw ratio by any drawing. The wide‐angle X‐ray diffraction photograph of the microfiber shows the existence of the oriented crystallites. Laser‐heating allows easier fabrication of microfibers compared with the conventional technology such as the conjugate spinning. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1534–1539, 2004     

中空纤维生产线开发PTT短纤维

概述了利用现有中空纤维生产线开发1.56dtex×38mmPTT短纤维的生产工艺,讨论了纺丝、拉伸、热定型等工艺条件对生产的影响。指出切片干燥不需预结晶过程,纺丝温度应比纺PET低30℃左右,应选择较低的拉伸速度、拉伸倍率和组件压力。     

Mechanical properties and superstructure of isotactic polypropylene fibers prepared by continuous vibrating zone‐drawing

A continuous vibrating zone‐drawing (CVZD) was applied to study the effect of vibration on the mechanical properties and superstructure of isotactic polypropylene fibers. The CVZD treatment was a new drawing method by which the fiber was continuously drawn at a rate of 0.5 m/min under vibration using the specially designed apparatus. The CVZD treatment was carried out in five steps at a drawing temperature of 150°C and a frequency of 100 Hz, and applied tensions increased step by step with processing in the range of 14.8 to 207 MPa. The obtained fiber had a birefringence of 0.0373, crystallinity of 62.4%, tensile modulus of 17.6 GPa, and tensile strength of 1.11 GPa. These values are higher than those of the continuous zone‐drawn isotactic polypropylene fiber previous reported. The vibration added to the fibers during the zone‐drawing was effective in developing amorphous orientation and improving the mechanical properties. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 600–608, 2001     

PTT的纺丝稳定性和聚集态结构

利用毛细管流变仪研究PTT熔体挤出时的破裂现象,讨论PTT纺丝稳定性和初生纤维聚集态结构。结屎表明,PTT熔体是一种拉伸变稀型流体。自由挤出时,即使剪切速率达到1.5×105 s-1时,挤出熔体也没有出现明显的熔体破裂;而在纺丝过程中,在卷绕速度达到3.8 km／min(剪切速率2.1×103 s-1)时,就出现明显的熔体断裂现象。在高速纺丝中,控制PTT初生纤维取向结构的关键是喷丝头拉伸比,决定结晶结构的关键是卷绕速度。增加喷丝头拉伸比可以提高初生纤维的取向度;提高卷绕速度可以提高纤维结晶度。     

Deformation processing of PMMA into high-strength fibers

Poly(methyl methacrylate) was drawn into fibers by melt extrusion followed immediately by a transient temperature drawing process. By varying five processing variables, fibers ranging from 0.635 mm to 25 μm in diameter were produced. Heat-induced relaxation of the aligned structure was used to determine the draw ratio of the resultant fibers and therefore the degree of polymer chain alignment imposed by the deformation process. The resulting changes in length and diameter were measured and it was found that draw ratios of 5–20 had been achieved under the varying processing conditions. It was also observed that fiber diameter immediately after drawing is a good predictor of the degree of orientation present in the fiber irrespective of the processing conditions. To test the effect molecular orientation has on material properties, fibers with varying degrees of orientation were tested in tension. As expected, increasing alignment resulted in increasing tensile strength. The maximum observed true ultimate tensile strength was 225 ± 53 MPa and was seen in fibers with a draw ratio equal to 18.7 ± 4.5. Fibers with a lower degree of alignment, while not as strong in tension, exhibited significantly increased ductility. True strains of as high as 25% were observed.     

Stereocomplex formation between enantiomeric poly(lactic acid). VIII. Complex fibers spun from mixed solution of poly(D-lactic acid) and poly(L-lactic acid)

To obtain poly(lactic acid) (PLA) complex fibers, spinning was performed by wet and dry methods from 5–10 g/dL chloroform solutions of poly(D-lactic acid) (PDLA) and poly(L-lactic), both with a viscosity-average molecular weight of 3 × 10⁵. The dope was extruded from a monohole nozzle into coagulation baths from ethanol and chloroform for wet spinning and into a drying column kept at 60°C for dry spinning. Scanning electron microscopic observation of the as-spun fibers showed that the surface of the wet-spun fiber had large basins with diameters of 50–100 μm and many pores with diameters from sub μm to 10 μm, whereas the surface of dry-spun fiber had a microporous structure with the pore diameter of 1–3 μm. The tensile strength of the wet-spun complex fiber was very low and could not be drawn at high temperatures, in contrast to the dry-spun fiber. The tensile strength of dry-spun complex fiber increased upon hot drawing and showed the tensile strength of 94 kg/mm² by drawing at 160°C to the draw ratio of 13. Differential scanning calorimetry revealed that the complex fibers contained both the stereocomplex crystallites (racemic crystallites) and the crystallites of the single polymers, PDLA and PLLA, regardless of the spinning methods. The ratio of the racemic crystallites to the single-polymer crystallites increased with the draw ratio of the complex fiber. © 1994 John Wiley & Sons, Inc.     

熔融纺丝法制备UHMWPE/MMT复合纤维的研究

以超高相对分子质量聚乙烯/蒙脱土(UHMWPE/MMT)纳米复合材料为原料,采用熔融纺丝法,在自行设计制造的实验纺丝机上制备出纤维,利用DSC、XRD、SEM等手段对其结构进行了表征,并对其性能进行了测试。拉伸条件试验表明,水浴温度85℃、拉伸倍率14倍,是纤维最佳拉伸温度与倍率;纤维在拉伸过程中存在一个最佳的甬道停留时间。微观结构分析表明,拉伸后得到的纤维熔点、取向度都得到了提高,并在一定条件下出现了正交晶形到六方晶形的转变。     

Zone drawn NEW-TPI thermoplastic polyimide and its blends with Xydar liquid crystalline polymer

In this work we report the effects of single stage zone drawing on the properties of NEW-TPI thermoplastic polyimide homopolymer, and its blends with Amoco's Xydar liquid crystalline polymer. Zone drawing was performed first on homopolymer NEW-TPI films to determine the effect of load weight, heater speed, and drawing temperature on the attainable draw ratio. Degree of crystallinity and chain orientation increase as the draw ratio increases for NEW-TPI. Blends of NEW-TPI/Xydar compositions 90/10 and 70/30 were studied next. In blends, the Xydar component is not molecularly dispersed, and is initially preferentially oriented along the machine direction during the film processing stage. Xydar acts as a nucleation site and lowers the temperature for crystallization of the NEW-TPI from the rubbery amorphous state. Zone drawing was performed either parallel or perpendicular to Xydar's initial preferred orientation direction. Blends with lower Xydar fraction could be zone-drawn to higher ratios. Zone drawing perpendicular to Xydar's initial orientation direction also resulted in increased draw ratio. Dynamic mechanical properties of the zone drawn materials were studied. In homopolymer NEW-TPI, dynamic modulus increased by a factor of two to 4.0 GPa in zone drawn films, largely as a result of the formation of oriented crystallites. In the blends, the modulus parallel to Xydar's initial orientation direction was greater than that in the transverse direction. Depending upon composition and test direction, zone drawing increased the dynamic moduli of the blends from 1.5 up to 2.7 times, in the temperature range from 150°C to 300°C.