Properties of poly(ethylene terephthalate) and maleic anhydride-grafted polypropylene blends by reactive processing

The properties of poly(ethylene terephthalate) (PET) and polypropylene (PP) blends and PET/maleic anhydride-grafted PP (MAgPP) reactive blends were investigated. Two blend systems were immiscible based on tan δ measured by dynamic mechanical analyzer (DMA). In case of PET/MAgPP blends, the reaction of ester groups of PET and MA sites on MAgPP occurred during melt mixing at 280°C for 30 min. The reaction was confirmed by a new peak between the glass transition temperatures of PET-rich and MAgPP-rich phase on tan δ curves, as well as from the rheological properties. From the morphology, the improvement of the dispersibility in PET/MAgPP reactive blends was observed. The modulus of PET/MAgPP blends was higher than that of PET/PP blends, and the strength of PET/MAgPP blends showed the good adhesion compared with the PET/PP blends. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 389–395, 1998     

Compatibilization of Poly(ethylene terephthalate)/Polypropylene Blends with Maleic Anhydride Grafted Polyethylene-Octene Elastomer

Blends of poly(ethylene terephthalate) (PET) and polypropylene (PP) at composition 80/20 with and without a compatibilizing agent were studied. Both materials are widely used in the soft drink bottle industry. The compatibilizing agent was a maleic anhydride grafted polyethylene-octene elastomer (POE-g-MA). The olefinic segment of POE is compatible with PP, whereas the maleic anhydride is affined with PET carbonyl groups. The effectiveness of the compatibilizing agent was evaluated using different techniques, such as Fourier transform IR spectroscopy, mechanical analysis, scanning electron microscopy, dynamic mechanical analysis, and rheological analysis. The results show that the addition of POE-g-MA promotes a fine dispersed-phase morphology, and improves process ability and toughness of these blends. Shifts in the glass-transition temperature of the PET phase and the increase in the melt viscosity of the compatibilized blends indicated enhanced interactions between the discrete PET and PP phases induced by the functional compatibilizer.     

Improved compatibility of high‐density polyethylene/poly(ethylene terephthalate) blend by the use of blocked isocyanate group

The blocked isocyanate group (BHI) was synthesized to improve the storage stability of HI (2‐hydroxyethyl methacrylate combined with isophorone diisocyanate) and characterized by Fourier transform infrared spectroscopy (FTIR). High‐density polyethylene grafted with the blocked isocyanate group (HDPE‐g‐BHI) was used as a reactive compatibilizer for an immiscible high‐density polyethylene/poly(ethylene terephthalate) (HDPE/PET) blend. A possible reactive compatibilization mechanism is that regenerated isocyanate groups of HDPE functionalized by BHI react with the hydroxyl and carboxyl groups of PET during melt blending. The HDPE‐g‐BHI/PET blend showed the smaller size of a dispersed phase compared to the HDPE/PET blend, indicating improved compatibility between HDPE and PET. This increased compatibility was due to the formation of an in situ graft copolymer, which was confirmed by dynamic mechanical analysis. Differential scanning calorimetry (DSC) analysis represented that there were few changes in the crystallinity for the continuous PET phase of the HDPE‐g‐BHI/PET blends, compared with those of the HDPE/PET blends at the same composition. Tensile strengths and elongations at the break of the HDPE‐g‐BHI/PET blends were greater than those of the HDPE/PET blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1017–1024, 2000     

PEN/PET共混物结晶行为研究

用差示扫描量热法(DSC)研究了不同共混比例PEN/PET共混物的熔体结晶行为,并进行了等温结晶动力学测定。结果表明:随着两种组分向中间比例(50/50)靠近,共混物的熔融温度越低,结晶速率也越慢。     

Mechanical and Rheological Properties of Poly(ethylene terephthalate)/ Polypropylene Blends

Poly(ethylene terephthalate) and polypropylene (PET/PP) were compounded and pelletized with a single-screw extruder. Standard ASTM tensile test specimens were made by injection moulding. The blends are stronger and stiffer than the plain PP specimens. The addition of a compatibilizer, EPOLENE E-43, is found to improve the strength and stiffness of the blends at loadings of 50% and 70% PET. At 10% PET loading, E-43 has the opposite effect of slightly reducing the tensile properties. All the blends are more brittle relative to either plain PET or PP. The addition of E-43 results in negligible improvement in the elongation at break. E-43 is also found to be an effective lubricant in improving the processability of the blends. The blends with E-43 added have lower viscosities and less shear-thinning characteristics than those without E-43. © 1997 SCI.     

Recycled poly(ethylene terephthalate)/linear low‐density polyethylene blends through physical processing

Poly(styrene‐ethylene/butylene‐styrene) (SEBS) was used as a compatibilizer to improve the thermal and mechanical properties of recycled poly(ethylene terephthalate)/linear low‐density polyethylene (R‐PET/LLDPE) blends. The blends compatibilized with 0–20 wt % SEBS were prepared by low‐temperature solid‐state extrusion. The effect of SEBS content was investigated using scanning electron microscope, differential scanning calorimeter, dynamic mechanical analysis (DMA), and mechanical property testing. Morphology observation showed that the addition of 10 wt % SEBS led to the deformation of dispersed phase from spherical to fibrous structure, and microfibrils were formed at the interface between two phases in the compatibilized blends. Both differential scanning calorimeter and DMA results revealed that the blend with 20 wt % SEBS showed better compatibility between PET and LLDPE than other blends studied. The addition of 20 wt % of SEBS obviously improved the crystallizibility of PET as well as the modulus of the blends. DMA analysis also showed that the interaction between SEBS and two other components enhanced at high temperature above 130°C. The impact strength of the blend with 20 wt % SEBS increased of 93.2% with respect to the blend without SEBS, accompanied by only a 28.7% tensile strength decrease. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology and electrical properties of carbon black/poly(ethylene terephthalate)/polypropylene composite

This work attempts to develop a carbon black (CB) filled conductive polymer composite based on poly(ethylene terephthalate) (PET) and polypropylene (PP). The process follows by localizing the CB particles in the minor phase (PET), and then the conductive masterbatch was elongated to form conductive microfibrils in PP matrix during melt extrusion process. After compression molding, a fine conductive three‐dimensional microfibrillar network is constructed. For comparison purpose, CB, PET, and PP are mixed using different pattern. The morphology and the volume resistivity of the obtained composites are evaluated. Electrical conductivity investigation shows that the percolation threshold and resistivity values are dependent on the CB concentration. The best morphological observation shows that the PET phases forms well‐defined microfibrils, and CB particles overwhelmingly localize in the surfaces of the PET microfibrils, which led to a very low percolation threshold, i.e., 4.5 phr, and a reasonable conductivity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Microstructure and crystallization of melt‐mixed poly(ethylene terephthalate)/poly(ethylene isophthalate) blends

Physical blends of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), abbreviated PET/PEI (80/20) blends, and of PET and a random poly(ethylene terephthalate‐co‐isophthalate) copolymer containing 40% ethylene isophthalate (PET₆₀I₄₀), abbreviated PET/PET₆₀I₄₀ (50/50) blends, were melt‐mixed at 270°C for different reactive blending times to give a series of copolymers containing 20 mol % of ethylene isophthalic units with different degrees of randomness. ¹³C‐NMR spectroscopy precisely determined the microstructure of the blends. The thermal and mechanical properties of the blends were evaluated by DSC and tensile assays, and the obtained results were compared with those obtained for PET and a statistically random PETI copolymer with the same composition. The microstructure of the blends gradually changed from a physical blend into a block copolymer, and finally into a random copolymer with the advance of transreaction time. The melting temperature and enthalpy of the blends decreased with the progress of melt‐mixing. Isothermal crystallization studies carried out on molten samples revealed the same trend for the crystallization rate. The effect of reaction time on crystallizability was more pronounced in the case of the PET/PET₆₀I₄₀ (50/50) blends. The Young's modulus of the melt‐mixed blends was comparable to that of PET, whereas the maximum tensile stress decreased with respect to that of PET. All blend samples showed a noticeable brittleness. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3076–3086, 2003     

Crystalline and thermal behavior of poly(ethylene terephthalate)/polyphenoxy blends

Poly(ethylene terephthalate) (PET)/polyphenoxy blends were prepared by melt blending. Crystalline and thermal behaviors of PET/polyphenoxy blends were verified by use of DSC. The experiment results show that the initial temperature, peak temperature, and ending temperature of cold crystallization increase with increasing phenoxy content. On the contrary, the onset melting temperature, finishing melting temperature, and peak temperature in the first heating and the secondary heating processes decrease with increasing phenoxy content. The crystallization enthalpy and melting enthalpy, as well as the crystallization rate, decrease with increasing phenoxy content. Avrami exponents of the blends are slightly higher than that of pure PET and almost independent of phenoxy content. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 878–885, 2005     

Chain extension of poly(ethylene terephthalate) by reactive blending using diepoxides

Molecular weight increase via chain extension reactions of poly(ethylene terephthalate) with commercially available diepoxides was studied in a custom‐made laboratory scale reactor and a Brabender rheomixer under reactive blending conditions. The products were characterized by carboxylic end group analysis, intrinsic viscosity, and differential scanning calorimetry. PET was effectively modified in the laboratory‐scale reactor using cyclic diepoxides because the resulting polymers show intrinsic viscosities that are comparable to virgin PET (0.68–0.75 dL/g vs. 0.74 dL/g) and much higher than processed PET (0.55), while carboxyl contents were reduced to a third of that of the virgin PET. Diglycidyl ethers produced polymers displaying decreased viscosity values, increased carboxyl content, and lower melting points. Low concentrations of extender and short reaction times generally favored chain extension. In addition, purging with nitrogen resulted in chain extended polymers having the highest values of intrinsic viscosity ([η] = 0.79, 0.82). Similar trends were observed with modified products in the rheomixer having somewhat smaller viscosity values, larger carboxyl contents, and increased melting points. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2121–2127, 1999     

Sequence analysis of poly(ethylene terephthalate)/poly(butylene terephthalate) copolymer prepared by ester-interchange reactions

The molecular structure of the copolyester formed through the interchange reaction in poly(ethylene terephthalate)/poly(butylene terephthalate) blends was investigated with ¹³C-NMR spectroscopy. The molar fractions of heterolinkage triads in the copolyesters were lower than the values calculated by Bernoullian statistics; this indicates that the sequence of heterolinkages was far from a random distribution at the initial stage of the interchange reaction. However, the randomness increased and the number-average sequence length decreased with reaction time. The solubility of the blend decreased with increasing sequence length, resulting from the formation of block copolymers with long sequence lengths at the initial stage of the interchange reaction. The solubility of the copolyester formed by a dibutyltin dilaurate (DBTDL)-catalyzed reaction was higher than that of the copolyester formed by a titanium tetrabutoxide-catalyzed reaction; this is related to the fact that alcoholysis prevailed in the DBTDL-catalyzed reaction. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 159–168, 2001     

支化聚酯的合成及热性能研究

通过直接酯化-缩聚工艺,在聚对苯二甲酸乙二醇酯(PET)聚合的缩聚过程中分别引入第三组分——3-羟甲基丙烷(TMP)、季戊四醇(PER)或双季戊四醇(DPT)合成了一系列不同的支化PET,并采用氢核磁共振波谱仪(1H-NMR)、差示扫描量热仪(DSC)和热重分析(TG)表征了产物的结构和性能。结果表明:与纯PET相比,经TMP、PER或DPT改性后的支化PET的玻璃化转变温度(Tg)均下降,含摩尔分数0.3%DPT改性的支化PET的Tg最低;除TMP1-PET外,各支化PET的冷结晶温度(Tc)都增大;各支化PET的熔点(Tm)也都呈现下降趋势;除PER3-PET外,各支化PET的结晶焓ΔHc都有所下降,而各支化PET的熔融焓ΔHm却变化不大;所得到的各支化PET具有较好的热稳定性能。     

Effects of pH and Neutral Salts on the Adsorption of the Poly(ethylene glycol terephthalate) Condensates Toward Poly(ethylene terephthalate) Fiber

This study deals with the effects of pH and neutral salts on the adsorption of PET fiber with four kinds of poly(ethylene glycol terephthalate) condensated from dimethyl terephthalate (DMT) and poly(ethylene glycol) (PEG). The surface properties of the aqueous solution, the contact angle of polyol‐treated PET fabrics, and its parameters were also discussed. The pH of the solution or the adding of neutral salt in the polyol solution largely affected the contact angle of polyol‐treated PET fabrics as well as the surface tension of the solution. A lower pH of the polyol solution or adding neutral salts in the solution showed a lower surface tension and a lower contact angle that resulted in a better adsorption between polyol and poly(ethylene terephthalate) fibers. The lower pH of the solutions and a higher valence of the added neutral salt in the solution showed a largely positive effect on the adsorption parameters, and the order of effectiveness is Al₂(SO₄)₃ > MgSO₄ > Na₂SO₄.     

Blends of poly(ethylene terephthalate) and poly(butylene terephthalate)

Commercial grade poly(ethylene terephthalate), (PET, intrinsic viscosity = 0.80 dL/g) and poly(butylene terephthalate), (PBT, intrinsic viscosity = 1.00 dL/g) were melt blended over the entire composition range using a counterrotating twin‐screw extruder. The mechanical, thermal, electrical, and rheological properties of the blends were studied. All of the blends showed higher impact properties than that of PET or PBT. The 50:50 blend composition exhibited the highest impact value. Other mechanical properties also showed similar trends for blends of this composition. The addition of PBT increased the processability of PET. Differential scanning calorimetry data showed the presence of both phases. For all blends, only a single glass‐transition temperature was observed. The melting characteristics of one phase were influenced by the presence of the other. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 75–82, 2005     

Spinning and properties of poly(ethylene terephthalate)/organomontmorillonite nanocomposite fibers

By in situ polycondensation, a intercalated poly(ethylene terephthalate)/organomontmorillonite nanocomposite was prepared after montmorillonite (MMT) had been treated with a water‐soluble polymer. This nanocomposite was produced to fibers through melt spinning. The resulting nanocomposite fibers were characterized by X‐ray diffraction (XRD), differential scanning calorimeter (DSC), and transmission electron microscopy (TEM). The interlayer distance of MMT dispersed in the nanocomposite fibers was further enlarged because of strong shear stress during processing of melt spinning. This was confirmed by XRD test and TEM images. DSC test results showed that incorporation of MMT accelerated the crystallization of poly(ethylene terephthalate) (PET), but the crystallinity of the drawn fibers just had a little increasing compared with that of neat PET drawn fibers. Also compared with pure PET drawn fibers, tensile strength at 5% elongation and thermal stability of the nanocomposite fibers were improved. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1443–1447, 2005     

聚对苯二甲酸乙二醇酯合成催化剂研究进展

探讨了各类锑系催化剂、钛系催化剂(包括乙二醇钛)等不同类型的催化剂在聚酯缩聚反应中的催化性能研究的最新成果,指出在各种类型催化剂中,由于具有作为催化剂时不会带入多余的杂质进入反应体系等优点,乙二醇锑和乙二醇钛的应用前景较为广阔。     

Synthesis and characterization of poly(ethylene terephthalate)/attapulgite nanocomposites

A kind of clay with fibrous morphology, attapulgite (AT), was used to prepare poly (ethylene terephthalate) (PET)/AT nanocomposites via in situ polymerization. Attapulgite was modified with Hexadecyltriphenylphosphonium bromide and silane coupling agent (3‐glycidoxypropltrimethoxysilane) to increase the dispersion of clay particles in polymer matrix and the interaction between clay particles and polymer matrix. FTIR and TGA test of the organic‐AT particles investigated the thermal stability and the loading quantity of organic reagents. XRD patterns and SEM micrographs showed that the organic modification was processed on the surface of rod‐like crystals and did not shift the crystal structure of silicate. For PET/AT nanocomposites, it was revealed in TEM that the fibrous clay can be well dispersed in polymer matrix with the rod‐like crystals in the range of nanometer scale. The diameter of rod‐like crystal is about 20 nm and the length is near to 500 nm. The addition of the clay particles can enhance the thermal stability and crystallization rate of PET. With the addition of AT in PET matrix, the flexural modulus of those composites was also increased markedly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1279–1286, 2007     

Recyclability of In Situ Microfibrillar Poly(ethylene terephthalate)/High‐Density Polyethylene Blends

Repetitive processing was employed to assess the recyclability of in situ microfibrillar poly(ethylene terephthalate) (PET)/high‐density polyethylene (HDPE) blends which were fabricated through a “rectangular slit die extrusion–hot stretching–quenching” process. For comparison, the conventional PET/HDPE blends were also obtained using the same processing operation but without hot stretching. The morphological observation indicated that slit die extrusion and hot stretching successfully made the dispersed PET phase deform in situ into well‐defined microfibrils. The average diameter of the microfibrils increased with the processing cycles. The rheological properties obtained from the parallel‐plate dynamic rheometer suggested that the microfibrillar blends have higher viscosity and viscoelastic moduli (storage and loss moduli) as well as better flow stability than the conventional PET/HDPE blend. More importantly, with the increase in the processing cycles, an increase in yield strength and unchanged tensile modulus were observed for in situ microfibrillar blends, while a decrease in these properties for conventional blend, indicating that the in situ microfibrillar PET/HDPE blends have promising recycling potential.

     

Synthesis and characterisation of copolyesters from poly(ethylene terephthalate) and poly(hexamethylene terephthalate)

Copolyesters containing poly(ethylene terephthalate) and poly(hexamethylene terephthalate) (PHT) were prepared by a melt condensation reaction. The copolymers were characterised by infrared spectroscopy and intrinsic viscosity measurements. The density of the copolyesters decreased with increasing percentage of PHT segments in the backbone. Glass transition temperatures (T_g). melting points (T_m) and crystallisation temperatures (T_c) were determined by differential scanning calorimetry. An increase in the percentage of PHT resulted in decrease in T_g, T_m and T_c. The as-prepared copolyesters were crystalline in nature and no exotherm indicative of cold crystallisation was observed. The relative thermal stability of the polymers was evaluated by dynamic thermogravimetry in a nitrogen atmosphere. An increase in percentage of PHT resulted in a decrease in initial decomposition temperature. The rate of crystallisation of the copolymers was studied by small angle light scattering. An increase in percentage of PHT resulted in an increase in the rate of crystallisation.