EFFECT OF TEMPERATURE ON THE ADSORPTION OF METHYLENE BLUE DYE ONTO SULFURIC ACID–TREATED ORANGE PEEL

The present study explains the preparation and application of sulfuric acid–treated orange peel (STOP) as a new low-cost adsorbent in the removal of methylene blue (MB) dye from its aqueous solution. The effects of temperature on the operating parameters such as solution pH, adsorbent dose, initial MB dye concentration, and contact time were investigated for the removal of MB dye using STOP. The maximum adsorption of MB dye onto STOP took place in the following experimental conditions: pH of 8.0, adsorbent dose of 0.4 g, contact time of 45 min, and temperature of 30°C. The adsorption equilibrium data were tested by applying both the Langmuir and Freundlich isotherm models. It is observed that the Freundlich isotherm model fitted better than the Langmuir isotherm model, indicating multilayer adsorption, at all studied temperatures. The adsorption kinetic results showed that the pseudo-second-order model was more suitable to explain the adsorption of MB dye onto STOP. The adsorption mechanism results showed that the adsorption process was controlled by both the internal and external diffusion of MB dye molecules. The values of free energy change (ΔG ^o) and enthalpy change (ΔH ^o) indicated the spontaneous, feasible, and exothermic nature of the adsorption process. The maximum monolayer adsorption capacity of STOP was also compared with other low-cost adsorbents, and it was found that STOP was a better adsorbent for MB dye removal.     

Analysis of intraparticle diffusion on adsorption of crystal violet on bentonite

Abstract

In the present work, kinetics of crystal violet (CV) adsorption on bentonite was studied by pore volume and surface diffusion model (PVSDM), surface diffusion model (SDM), and pore volume diffusion model (PVDM). The adsorption decay curves were obtained in batch system using different adsorbent dosages. The PVDM model did not interpreted the kinetic adsorption since the calculated value of D_p equal to 5.64?×?10^?7 cm² s^?1 predicted a slower adsorption than that obtained by the experimental data. The PVSDM results indicates that the intraparticle diffusion is predominantly due to surface diffusion (93%) and the pore volume diffusion can be negligible. Once the surface diffusion was the limiting step, the estimation with one (D_s) and two (D_sq and α) parameters were tested in the SDM model. The statistical analysis revealed that the one-parameter SDM model was most appropriate to predict the CV adsorption on bentonite. The optimal values of Ds ranged from 6.19?×?10^?10 to 6.49?×?10^?10 cm² s^?1, and decrease with the adsorbent dosage.     

Utilization of waste plastic pet bottles to prepare copper-1,4-benzenedicarboxylate metal-organic framework for methylene blue removal

ABSTRACT

The study aims to use waste plastic PET bottles to recover terephthalic acid for preparing copper-1,4-benzenedicarboxylate, which was then utilized as an adsorbent for removal of methylene blue (MB) from aqueous solutions after carefully characterizing by XRD, FTIR, TGA, SEM, and EDX. The optimum conditions were established as pH = 6, 25°C, adsorbent dose of 1 g L^?1, contact time of 20 min, and agitation speed of 150 rpm. The adsorption process was spontaneous, exothermic, fitting well to Langmuir isotherm model with the maximum adsorption capacity of 41.01 mg g^?1 and more suitable to be described by the pseudo first-order kinetic model. It was indicated that the physical adsorption plays a leading role in the adsorption process. The recycling study was also conducted to confirm the long-term use of the synthesized adsorbent.     

Adsorption of methylene blue onto powdered activated carbon immobilized in a carboxymethyl sago pulp hydrogel

The potential of crosslinked carboxymethyl sago pulp (CMSP) beads immobilized with powdered activated carbon (PAC) as an adsorbent for methylene blue (MB) adsorption was investigated. The finely powdered PAC had an excellent adsorption capacity for MB but was disadvantageous for the separation process from treated effluents. To ease the separation process, the CMSP medium could be advantageous for the process by acting an immobilizing medium for PAC. The MB adsorption reached equilibrium at the 14th hour, and further adsorption was studied to determine the effects of the CMSP concentration, PAC dosage, and pH. Different CMSP concentrations in the preparation of CMSP–PAC beads showed no significant differences; this proved that CMSP–PAC adsorbed more MB than CMSP did. The MB adsorption increased with increasing PAC concentration, whereas the CMSP–PAC beads disintegrated at pH 11.5. In the equilibrium study, the Langmuir isotherm fit well into the experimental data with a linear correlation coefficient (R ²) of 0.9837 and a maximum adsorption capacity of 250 mg/g. The kinetic study showed that pseudo‐second‐order kinetics accommodated the experimental data well with an R ² value of 0.9512 and a pseudo‐second‐order rate constant value of 3.61 × 10^?3 min^?1. The crosslinked CMSP–PAC beads have the potential to remove MB dye, and this could be exploited as an alternative to treating colored dye effluents produced by industries such as the textile, printing, and cosmetics industries. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44271.     

Starch/rice husk ash based superabsorbent composite: high methylene blue removal efficiency

Superabsorbent hydrogels composites based on the biopolymer starch (ST) and rice husk ash (RHA) were successfully developed and tested towards the removal of methylene blue (MB), a cationic dye. RHA content hit the morphology, mechanical and water uptake properties of the composite. Batch adsorption experiments, carried out under pH 5 at 33 °C and with 2000 mg L^?1 as the initial concentration of MB, showed that at 5 wt% RHA the composite exhibited a remarkable adsorption capacity reaching up to 1906.3 mg g^?1 within 60 min. The adsorption kinetics followed the pseudo-second-order model and intraparticle diffusion was involved in this process. The Langmuir adsorption isotherm suggested a monolayer formation and spontaneous process. Thermodynamic parameters confirmed the spontaneity of the adsorption and suggested electrostatic interaction among the cationic dye molecules and the anionic adsorption sites on the adsorbent surface. FTIR analysis confirmed the adsorption process occurs via electrostatic mechanism associated with hydrophobic interactions. The adsorbents showed reusability with slight loss of adsorption capacity in five consecutive adsorption/desorption cycles. These results demonstrate ST/RHA superabsorbent composite as a low-cost, eco-friendly, robust and powerful adsorbent material for wastewater remediation.     

Removal of Crystal Violet Dye from Aqueous Solution Using Calcined and Uncalcined Mixed Clay Adsorbents

In this work, calcined and uncalcined mixed clays containing kaolin, ball clay, feldspar, pyrophyllite, and quartz are examined as a potential adsorbent for the removal of crystal violet dye from aqueous solution. These clays are characterized by nitrogen adsorption/desorption isotherms, X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, and thermo gravimetric analysis (TGA). The kinetics and thermodynamic parameters as well as the effects of the pH, the temperature, and the adsorbent dosage have also been investigated. The experimental results indicate that the Langmuir model expresses the adsorption isotherm better than the Freundlich model. The obtained result showed a tremendous increase in the crystal violet adsorption capacity (1.9 × 10^?3 mol g^?1) after calcination, which is one order greater than that of the uncalcined mixed clay. The mechanism of the adsorption process is elucidated on the basis of experimental data. The percentage removal of crystal violet dye increases with increasing the pH, the temperature, and the adsorbent dosage. The investigation of kinetic studies indicates that the adsorption of crystal violet on calcined and uncalcined mixed clays could be described by the pseudo-second-order model. The negative Δ G ⁰ values obtained from the thermodynamic investigation confirm that the adsorption is spontaneous in nature. The adsorption results suggest that the calcined and uncalcined mixed clays can also be used as low cost alternatives to the expensive activated carbon for the removal of dyes from aqueous solution.     

Adsorption of Furfural from Aqueous Solution onto Activated Carbon: Kinetic,Equilibrium and Thermodynamic Study

Abstract

The present study aims to evaluate the influence of various experimental parameters viz. initial pH (pH ₀), adsorbent dose, contact time, initial concentration and temperature on the adsorptive removal of furfural from aqueous solution by commercial grade activated carbon (ACC). Optimum conditions for furfural removal were found to be pH ₀ ≈ 5.9, adsorbent dose ≈ 10 g/l of solution and equilibrium time ≈ 6.0 h. The adsorption followed pseudo‐second‐order kinetics. The effective diffusion coefficient of furfural was of the order of 10^?13 m²/s. Furfural adsorption onto ACC was found to be best represented by the Redlich‐Peterson isotherm. A decrease in the temperature of the operation favorably influenced the adsorption of furfural onto ACC. The positive values of the change in entropy (ΔS ⁰); and the negatived value of heat of adsorption (ΔH ⁰) and change in Gibbs free energy (ΔG ⁰) indicated feasible, exothermic, and spontaneous nature of furfural adsorption onto ACC.     

Fixed-bed column performance of methylene blue biosorption by Luffa cylindrica: statistical and mathematical modeling

Abstract

This study aimed to investigate the adsorption capacity of Iranian Luffa cylindrica as a natural lignocellulosic adsorbent for biosorption of methylene blue (MB) using a fixed-bed column. The response surface methodology based on central composite design was used to evaluate the interactive effects of three major operating parameters (inlet MB concentration, Luffa dosage, and feed flow rate) on the dye removal percentage (response variable). The significance of the proposed quadratic model was validated by a high coefficient of determination (R²?=?0.995) and a low p value (<0.001). The optimum biosorption conditions were determined as inlet MB concentration 38.66?mg?L^?1, Luffa dosage 2.78?g, and feed flow rate 5?mL?min^?1, and the maximum MB removal efficiency was founded to be 51% (q_max?=?21.4?mg?g^?1) at optimum conditions. The breakthrough curves were predicted by the Adams–Bohart and Thomas models using nonlinear regression analysis, whereas the experimental data fitted well with the Thomas model (R²?≈?0.96–0.98). Further surface modification studies enabled us to achieve the maximum MB removal efficiency of 77% (q_max?=?46.58?mg?g^?1) with NaOH-modified Luffa, which is attributed to the intensification of the negatively charged surface of the base-modified adsorbent with hydroxyl groups. The nature of biosorbent–dye interactions was also evaluated by FTIR analysis. The highest desorption performance of MB from Luffa fibers was obtained with HCl solution reaching a desorbed amount of q_des?=?130.5?mg in the column studies. The ion exchange is introduced as the dominant biosorption mechanism of MB onto Luffa fibers in this study.     

Adsorptive removal of congo red dye (CR) from aqueous solution by Cornulaca monacantha stem and biomass-based activated carbon: isotherm,kinetics and thermodynamics

Cornulaca monacantha stem (CS) and biomass stem-based activated carbon (CS^AC) were explored for the removal of congo red (CR) dye from water system. The biomaterial was characterized using Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) and field emission scanning electron microscope (FESEM). The BET surface area of biomass stem-based activated carbon (CS^AC) was recorded to be 304.27 m²/g. The influence of different parameters such as initial CR concentration, adsorbent dosage, contact time, adsorbate pH and temperature onto CR adsorption were studied.The maximum adsorption of CR dye 97.19% and 86.43% were achieved at 55°C using CS^AC and CS adsorbents, respectively. The isotherm, kinetics and thermodynamic study were also investigated to explore the adsorption mechanism. The adsorption isotherm closely follow the Langmuir model (R² = 0.99) suggesting the monolayer adsorption of CR dye. Kinetic results indicated that pseudo second-order and Elovich model provide the better regression coefficient. Thermodynamic study revealed the feasible, spontaneous and endothermic nature of adsorption process. The regeneration study implies that adsorbent was efficiently recovered from CR dye with 0.01 mol/L NaOH solution. The CS^AC adsorbent possesses 75.75% uptake for CR dyes after 6th cycles of desorption-adsorption, respectively. .     

Sorption Potential of Styrene‐Divinylbenzene Copolymer Beads for the Decontamination of Lead from Aqueous Media

Abstract

The decontamination of lead ions from aqueous media has been investigated using styrene‐divinylbenzene copolymer beads (St‐DVB) as an adsorbent. Various physico‐chemical parameters such as selection of appropriate electrolyte, contact time, amount of adsorbent, concentration of adsorbate, effect of foreign ions, and temperature were optimized to simulate the best conditions which can be used to decontaminate lead from aqueous media using St‐DVB beads as an adsorbent. The atomic absorption spectrometric technique was used to determine the distribution of lead. Maximum adsorption was observed at 0.001 mol L^?1 acid solutions (HNO₃, HCl, H₂SO₄ and HClO₄) using 0.2 g of adsorbent for 4.83×10^?5 mol L^?1 lead concentration in two minutes equilibration time. The adsorption data followed the Freundlich, Langmuir, and Dubinin‐Radushkevich (D‐R) isotherms over the lead concentration range of 1.207×10^?3 to 2.413×10^?2 mol L^?1. The characteristic Freundlich constants i.e. 1/n=0.164±0.012 and A=2.345×10^?3±4.480×10^?5 mol g^?1 have been computed for the sorption system. Langmuir isotherm gave a saturated capacity of 0.971±0.011 mmol g^?1, which suggests monolayer coverage of the surface. The sorption mean free energy from D‐R isotherm was found to be 18.26±0.75 kJ mol^?1 indicating chemisorption involving chemical bonding for the adsorption process. The uptake of lead increases with the rise in temperature. Thermodynamic parameters i.e. ΔG, ΔH, and ΔS have also been calculated for the system. The sorption process was found to be exothermic. The developed procedure was successfully applied for the removal of lead ions from real battery wastewater samples.     

Adsorptive Removal of Lead from Battery Wastewater by Coconut Coir

The sorption behavior of lead ions on coconut coir has been investigated to decontaminate lead ions from aqueous solutions. Various physico-chemical parameters were optimized to simulate the best conditions in which this material can be used as an adsorbent. Maximum adsorption was observed at 0.0001 to 0.001 mol L^?1 of acid solutions (HNO₃, HCl and HClO₄) using 0.4 g of adsorbent for 4.83 × 10^?5 mol L^?1 lead concentration in ten minutes equilibration time. The adsorption of lead was decreased with the increase in the concentrations of all the acids used. The kinetic data indicated an intraparticle diffusion process with sorption being pseudo-second order. The determined rate constant k₂ was 8.8912 g mg^?1 min^?1. The adsorption data obeyed the Freundlich isotherm over the lead concentration range of 2.41 × 10^?4 to 1.45 × 10^?3 mol L^?1. The characteristic Freundlich constants i.e., 1/n = 0.44 ± 0.02 and K = 0.184 ± 0.0096 m mol g^?1 have been computed for the sorption system. The sorption mean free energy from the Dubinin-Radushkevich isotherm is 10.48 ± 0.72 kJ mol^?1 indicating the ion-exchange mechanism of chemisorption. The uptake of lead increases with the rise in temperature (293–333 K). Thermodynamic quantities i.e., ΔG, ΔS, and ΔH have also been calculated for the system. The sorption process was found to be endothermic. The proposed procedure was successfully applied for the removal of lead from battery wastewater samples.     

Adsorption of Lignosulfonate Compound from Aqueous Solution onto Chitosan-Silica Beads

The main objective of this study is to investigate the possibility of crosslinked chitosan-tetraethoxy orthosilane (TEOS) (chitosan-silica) beads to be used as an adsorbent material to adsorb the lignosulfonate compound in solution. Different parameters affecting the adsorption capacity such as contact time, adsorbent dosage, initial concentration, pH, ionic strength, and temperature have been investigated. Adsorption isotherms of lignosulfonates onto chitosan-silica beads were also studied. Batch adsorption experiments were carried out and the optimum lignosulfonate adsorption onto chitosan-silica beads occurred at contact time of 30 minutes, the adsorbent dosage of 40 g/L, initial concentration of 50 mg/L, pH 5, and a temperature of 45°C. Adsorption isotherms studied through the use of graphical methods revealed that the adsorption of lignosulfonates onto chitosan-silica beads follows the Langmuir model, with the maximum adsorption capacity being 238.3 mg/g at pH 7. Adsorption is dependent on the ionic strength. The adsorption of lignosulfonate on chitosan-silica beads was best described with the pseudo-second-order kinetic model with a rate constant of 0.32 g · mg^?1 · min^?1, while intra-particle-diffusion was the main rate-determining step in the lignosulfonate adsorption process. The chitosan-silica beads investigated in this study were thus exhibited as a high potential adsorbent for the removal of lignosulfonate from solution.     

Removal of methylene blue from aqueous solution by adsorption onto zeolite synthesized from coal fly ash and its thermal regeneration

BACKGROUND: The removal of cationic dyes from wastewater is of great importance. Three zeolites synthesized from coal fly ashes (ZFAs) were investigated as adsorbents to remove methylene blue (MB), a cationic dye, from aqueous solutions. Experiments were conducted using the batch adsorption technique under different conditions of initial dye concentration, adsorbent dose, solution pH, and salt concentration. RESULTS: The adsorption isotherm data of MB on ZFAs were fitted well to the Langmuir model. The maximum adsorption capacities of MB by the three ZFAs, calculated using the Langmuir equation, ranged from 23.70 to 50.51 mg g^?1. The adsorption of MB by ZFA was essentially due to electrostatic forces. The measurement of zeta potential indicated that ZFA had a lower surface charge at alkaline pH, resulting in enhanced removal of MB with increasing pH. MB was highly competitive compared with Na⁺, leading to only a < 6% reduction in adsorption in the presence of NaCl up to 1.0 mol L^?1. Regeneration of used ZFA was achieved by thermal treatment. In this study, 90–105% adsorption capacity of fresh ZFA was recovered by heating at 450 °C for 2 h. CONCLUSION: The experimental results suggest that ZFA could be employed as an adsorbent in the removal of cationic dyes from wastewater, and the adsorptive ability of used ZFA can be recovered by thermal treatment. Copyright © 2010 Society of Chemical Industry     

Potential of Rice Husk for the Decontamination of Silver Ions from Aqueous Media

The sorption behavior of silver ions on rice husk has been investigated in detail. Various physico-chemical parameters were optimized to simulate the best conditions in which this material can be used as an adsorbent. Maximum adsorption was observed at 0.001 mol L^?1 of acid solutions (HNO₃, H₂SO₄ and HClO₄) using 0.5 g of adsorbent for 9.27 × 10^?5 mol L^?1 silver concentration in fifteen minutes equilibration time. The adsorption of silver was decreased with the increase in the concentrations of all the acids used. The kinetic data indicated an intraparticle diffusion process with sorption being pseudo-second order. The determined rate constant k₂ was 14.707 ± 1.832 mol g^?1 min^?1. The adsorption data obeyed the Freundlich, Langmuir, and Dubinin-Radushkevich isotherms over the silver concentration range of 1.85 × 10^?4 to 1.16 × 10^?3 mol L^?1. The characteristic Freundlich constants, that is, 1/n = 0.38 ± 0.033 and K = 0.271 ± 0.104 m mol g^?1 whereas the Langmuir constants Q = (1.504 ± 0.054) × 10^?2 m mol g^?1 and b = (16.582 ± 2.227) × 10³ dm³ mol^?1 have been computed for the sorption system. The sorption mean free energy from the Dubinin-Radushkevich isotherm is 12.16 ± 0.82 kJ mol^?1 indicating ion-exchange mechanism of chemisorption. The uptake of silver increases with the rise in temperature (283–333 K). Thermodynamic quantities, namely, ΔG, ΔS, and ΔH have also been calculated for the system. The sorption process was found to be endothermic. The effect of other cations and anions on the adsorption of silver has also been studied.     

Investigation of Cationic Dye Adsorption from Water onto Acetic Acid Lignin

An adsorbent was prepared from acetic acid lignin (AAL) to investigate the adsorption mechanism of methylene blue (MB) from water. AAL was first deacetylated in NaOH aqueous solution and then fractionated by methanol to prepare adsorbents with various acidic hydroxy groups. The adsorption capacities of MB increased with the increase in initial pH and with the decrease in adsorbent dosage. The results of adsorption kinetics indicated the dye uptake process is a chemisorption. The adsorption capacity of lignin for MB adsorption increased from 18.2 to 63.3 mg g^?1 as AAL was deacetylated and fractionated.     

Activated carbon from bacterial cellulose as an effective adsorbent for removing dye from aqueous solution

ABSTRACT

Novel activated carbon (AC) derived from bacterial cellulose (BC-AC) was produced by phosphoric acid activation at a carbonization temperature of 500 °C. BC-AC possesses mesoporous structures of 2.3 nm in diameter, porosity of 1.0 cm³/g and surface area of 1734 m²/g with high thermal stability between 100 and 500 °C. BC-AC could be used as an effective adsorbent for removing methylene blue (MB) from aqueous solutions with the maximum adsorption capacity of 505.8 mg/g. BC-AC presented physisorption and the adsorption of MB was most likely to be a monolayer adsorption. The Redlich–Peterson model displayed the best fit with the experimental data.     

Synthesis and adsorptive properties of sulfonated nanocomposites based on carbon-encapsulated iron nanoparticles and styrene-p-divinylbenzene copolymer

ABSTRACT

A method of the synthesis of novel magnetic nanocomposite adsorbent of Fe(III) from aqueous solutions is presented. The nanocomposites consisted of carbon-encapsulated iron nanoparticles and styrene-p-divinylbenzene copolymer. The adsorptive active sites were introduced via the post-synthesis sulfonation. The presented sulfonated magnetic nanocomposite adsorbents can be easily separated using permanent magnets and their adsorption performance was comparable to the commercially available ion-exchange resins. The determined maximum adsorption capacities were between 10.9 and 49.5 mg?g^?1, whilst the equilibrium was reached for the contact time lower than 60 minutes.     

Sodic and Acidic Crystalline Lamellar Magadiite Adsorbents for the Removal of Methylene Blue from Aqueous Solutions: Kinetic and Equilibrium Studies

The present study reports the feasibility of two synthetic crystalline lamellar nano-silicates, sodic magadiite (Na-mag) and its converted acidic form (H-mag), as alternative adsorbents for the removal of the dye methylene blue (MB) from aqueous solutions. The ability of these adsorbents for removing the dye was explored through the batch adsorption procedure. Effects such as the pH and the adsorbent dosage on the adsorption capacities were explored. Four kinetic models were applied, the adsorption being best fitted to a fractionary-order kinetic model. The kinetic data were also adjusted to an intra-particle diffusion model to give two linear regions, indicating that the kinetics of adsorption follows multiple sorption rates. The equilibrium data were fitted to Langmuir, Freundlich, Sips, and Redlich-Peterson isotherm models. The maxima adsorption capacities for MB of Na-mag and H-mag were 331 and 173 mg g^?1, respectively.     

Removal of victoria blue from aqueous solution by fly ash

The use of fly ash for the removal of victoria blue (C126, 44045) from aqueous solution at different concentrations and pH has been investigated. The process follows first order adsorption rate expression and the rate constant was found to be 1.70 × 10^?2 min^?1 at a victoria blue concentration of 1.0 × 10^?4 M and 25°C. The uptake of victoria blue by fly ash is diffusion controlled and the value of mass transfer coefficient is 1.25 × 10^?5 cm sec^?1. The equilibrium data fit well in the Langmuir model of adsorption. Maximum removal was noted at pH 8.0. Low desorption of dye from adsorbent surface indicates that the process may not be essentially a reversible one.     

Removal of Cu(II), Fe(III), and Cr(III) from Aqueous Solution by Aniline Grafted Silica Gel

Abstract

The aniline moiety was covalently grafted onto silica gel surface. The modified silica gel with aniline groups (SiAn) was used for removal of Cu(II), Fe(III), and Cr(III) ions from aqueous solution and industrial effluents using a batch adsorption procedure. The maximum adsorption of the transition metal ions took place at pH 4.5. The adsorption kinetics for all the adsorbates fitted better the pseudo second‐order kinetic model, obtaining the following adsorption rate constants (k₂): 1.233 · 10^?2, 1.902 · 10^?2, and 8.320 · 10^?3 g · mg^?1 min^?1 for Cr(III), Cu(II), and Fe(III), respectively. The adsorption of these transition metal ions were fitted to Langmuir, Freundlich, Sips, and Redlich‐Peterson isotherm models; however, the best isotherm model fitting which presented a lower difference of the q (amount adsorbed per gram of adsorbent) calculated by the model from the experimentally measured, was achieved by using the Sips model for all adsorbates chosen. The SiAn adsorbent was also employed for the removal of the transition metal ions Cr(III) (95%), Cu(II) (95%), and Fe(III) (94%) from industrial effluents, using the batch adsorption procedure.