Efficacy of tri-n-octylamine,tri-n-butyl phosphate and di-(2-ethylhexyl) phosphoric acid for reactive separation of protocatechuic acid

ABSTRACT

Owing to its chemical and pharmacological significances, the efficacy of reactive separation of protocatechuic acid (0.001–0.01 kmol m^?3) from aqueous stream by means of tri-n-octylamine (TOA), di-2-ethylhexyl phosphoric acid (D2EHPA) as well as tri-n-butyl phosphate (TBP) in octanol has been investigated, in terms of extraction efficiency, loading ratio, equilibrium complexation constants, and distribution coefficients. Extraction ability was obtained in the order TOA (91.2%) > TBP (88.64%) > D2EHPA (86.43%). In all cases, 1:1 protocatechuic acid:extractant complex is obtained. Further, diffusion coefficients, number of stages for extraction systems, and relative basicity model were used for relating the efficacy.     

Synergistic extraction and separation of Fe(III) and Zn(II) using TBP and D2EHPA

Waste chloride pickle liquors from hot-dip galvanizing plants, steel plants and flue dust contain reasonable amounts of heavy metals such as Zn, Cr, Ni, etc. Iron is invariably associated with most of these materials and comes into solution during leaching. Thus, the synergistic extraction of zinc(II) and iron(III) from leach solutions in tri-n-butyl phosphate (TBP)–di(2-ethylhexyl) phosphoric acid (D2EHPA) system diluted in kerosene was investigated. The Zn and Fe concentrations in the leach liquor used in the present study were 2 g/L. Experiments were carried out in the pH range of 0.5–4.0, temperature of 25°C, using sole D2EHPA, sole TBP and D2EHPA–TBP mixtures at different ratios. Results showed that the co-extraction of zinc(II) and iron(III) increased with increasing equilibrium pH using D2EHPA. It is demonstrated that the mixtures of TBP and D2EHPA are more efficient and selective than D2EHPA alone. At low pH values, the separation factor is low when pure D2EHPA is used as an extractant; however, using TBP as a synergist, the separation factor increases and results in a better separation of zinc from iron. Increasing TBP to D2EHPA ratios in the organic phase caused a slight shift to the right in the extraction isotherm of iron and a marked shift to the right in the extraction isotherm of zinc, and the maximum separation factor of 13.3 × 10³ was achieved at a TBP to D2EHPA volume ratio of 4:1 (0.58 M TBP: 0.12 M D2EHPA). Furthermore, the effect of equilibrium pH, organic to aqueous phase ratio and Cl^? concentration on the selective extraction was investigated. Using two extraction stages at the O/A ratio of 2:1 and pH_e (equilibrium pH) of 3 and 1 for zinc and iron, respectively, 99% of zinc(II) and 96.25% of iron(III) were extracted.     

二（2-乙基己基）磷酸/磷酸三丁酯复合萃取剂协萃对氨基苯甲酸

为强化两性官能团化合物的萃取分离性能,以对氨基苯甲酸（PABA）为被分离溶质,二（2-乙基己基）磷酸（D2EHPA）/磷酸三丁酯（TBP）/正庚烷的混合物为萃取剂进行了萃取平衡特性的研究,考察了溶液的pH值、D2EHPA浓度、TBP浓度对于萃取平衡的影响,建立了复合萃取剂协同萃取PABA的萃取平衡分配系数的表达式.结果表明,D2EHPA/TBP/正庚烷复合萃取剂萃取PABA具有明显的协萃效应,协萃机理为D2EHPA及TBP分别与PABA的Lewis碱性官能团（—NH2）和Lewis酸性官能团（—COOH）缔合形成亲油性更强的萃合物,且D2EHPA与TBP的浓度差异越小,协萃效应越明显.根据萃取平衡分配系数表达式拟合求取了表观萃取平衡常数,复合萃取剂的值远大于D2EHPA、TBP单独作为萃取剂的值,进一步证明了本文提出的协萃机理.     

Production of high purity rare earth mixture from iron-rich spent fluid catalytic cracking (FCC) catalyst using acid leaching and two-step solvent extraction process

Acid leaching and a two-step solvent extraction procedure were developed to produce high purity mixture of La and Ce from iron-rich spent FCC catalyst discharged from Dzung Quat refinery (Vietnam). Acid leaching of the spent catalyst with 2M HNO₃ and a solid-to-liquid ratio of 1/3 at 80 °C in 1 h dissolved almost 90% of La while 12% of Al and 25% of Fe were transferred to the leachate. The extraction of RE metals and main impurities such as Al and Fe by a mixture of di-2-ethylhexyl phosphoric acid (D2EHPA) and tributyl phosphate (TBP) was investigated. Experiments showed that it was necessary to remove Fe before extracting RE and the optimum extraction conditions for a high recovery of RE while 0% of Al extraction were pH-1, contact time=10min, and D2EHPA/TBP volume ratio= 4: 1. At these conditions, the extraction yields of La(III) and Ce(III) were 72% and 89%, respectively. A two-step solvent extraction was developed to achieve a high purity of RE mixture, which included (1) the removal of impurity Fe by 25% (v/v) diisooctyl phosphinic acid (DiOPA) in n-octane for 140 min, (2) the extraction of rare earths by a mixture of di-2-ethylhexyl phosphoric acid (D2EHPA) and tributyl phosphate (TBP) in n-octane for 10 min without the need for adjusting the pH of the leaching solution.     

Comparative Study on Reactive Extraction of Picolinic Acid with Six Different Extractants (Phosphoric and Aminic) in Two Different Diluents (Benzene and Decan-1-ol)

The equilibrium study on reactive extraction of picolinic acid by six different extractants (phosphoric and aminic) dissolved in two different diluents (benzene and decane-1-ol) is carried out to evaluate the performance of extractants and diluents. The extraction ability in terms of the distribution coefficient (K _D) is found to be in the order of tri-n-octylamine (TOA) ≥ tri-n-dodecylamine (TDDA) > di-2-ehylhexyl phosphoric acid (D2EHPA) > tri-n-butyl phosphate (TBP) > tri-octyl methyl ammonium chloride (Aliquat 336) > tri-n-octyl phosphine oxide (TOPO) with both diluents. Decan-1-ol is found to be the better solvating medium for the acid-extractant complexes. A mathematical model based on mass action law is employed to estimate the values of partition coefficient (P) and dimerization constant (D) in physical extraction, and equilibrium extraction constants (K _E) in chemical extraction. The values of loading ratios (Z) less than 0.5 imply the formation of (1:1) acid:extractant solvates in the organic phase. Decan-1-ol with TOA is the most effective solvation medium with K _{D, max} = 9 at 0.01 kmol · m^?3 of picolinic acid and K _E = 19.448 m³ · kmol^?1.     

Recovery of oxalate from scrubbing solution containing rare earths and iron produced during uranium recovery from phosphoric acid

A solution containing oxalate complexes of rare earths, yttrium and iron (III) is obtained during the processing of wet process phosphoric acid for uranium recovery by solvent extraction. A process is described to recover oxalic acid from such a solution. The process is based on the conversion of iron (III) oxalate into calcium oxalate by calcium chloride followed by the metathesis of calcium oxalate with sulphuric acid to produce calcium sulphate and free oxalic acid. Data is presented to illustrate the influence of various parameters such as pH, temperature, digestion time and amount of calcium chloride on effective conversion of calcium oxalate. Under optimized conditions of pH 1, digestion time 2 h, twice the stoichiometric ratio of calcium chloride at ambient temperature (30±1°C) the recovery of calcium oxalate was found to be >94%. An overall schematic material balance flow -sheet for treating the oxalate solution of rare earths, yttrium and iron (III) to oxalic acid recovery has been presented. An improvement in the second cycle of patented process flow-sheet based on 1.5 M D2EHPA + 0.2 M TBP incorporating oxalic acid scrubbing / recycle for uranium recovery from phosphoric acid has been tested and found to be simple in terms of operations and capable of meeting product specifications..     

Studies on the Separation and Recovery of Uranium from Phosphoric Acid Medium Using a Synergistic Mixture of (2-Ethylhexyl)phosphonic Acid Mono 2-Ethyl Hexyl Ester (PC-88A) and Tri-n-octylphosphine Oxide (TOPO)

This paper deals with studies on the extraction of uranium(VI) from phosphoric acid medium using (2-ethylhexyl)phosphonic acid mono 2-ethylhexyl ester and tri-n-octylphosphine oxide individually as well as from their synergistic mixture. Different extraction parameters were investigated. With an increase in phosphoric acid concentration in the aqueous phase, the distribution ratio (Du) was found to decrease in all the cases. Synergism was observed when a mixture of PC-88A and TOPO was used. The synergistic mixture in the mole ratio of 4:1 (1.80 M PC-88A: 0.45 M TOPO) in xylene was found to be most suitable for uranium extraction. Among the various strip liquors used, 5% (w/v) solution of (NH₄)₂CO₃ was found to be the most suitable. Using a mixture of 1.8 M PC-88A and 0.45 M TOPO as the extractant system and 0.5 M ammonium carbonate as the stripping agent, uranium recovery was found to be better than 97% ± 3% in multiple contacts, (n = 2) from actual Davies Gray Waste while in case of wet phosphoric acid more than 52% ± 3% (n = 3) only could be recovered where n is the number of contacts.     

URANIUM EXTRACTION FROM WET PROCESS PHOSPHORIC ACID USING A LIQUID PHOSPHINE OXIDE SYNERGIST

Synergic mixtures of D2EHPA and TOPO are used commercially in the solvent extraction of small concentrations of uranium from wet process phosphoric acid. However, TOPO is a solid at normal temperatures (melting point is approximately 50^°C) and this can lead to some materials handling difficulties during inventory preparation and solvent make up. Batch shake out tests show that a new, liquid phosphine oxide (also used in combination with D2EHPA) provides essentially equivalent extraction performance to TOPO.     

Reactive solvent extraction of amino acids with cationic extractants

A mixture of amino acids (arginine, phenylalanine, alanine, glycine and aspartic acid) in solution was extracted by four acidic extractants (dinonylnaphthalenesulphonic acid (DNNSA), di(2-ethylhexyl)monothiophosphoric acid (D2EHPA(S)), di(2-ethylhexyl)phosphoric acid (D2EHPA) and Versatic 10) in toluene. The extractive capacity of the organic phase for the amino acids, using DNNSA, D2EHPA(S) and D2EHPA was found to decrease in the order arginine>phenylalanine>alanine>glycine>aspartic acid, although at low pH values phenylalanine>arginine occurred for D2EHPA(S) and D2EHPA. Separation factors derived for pairs of amino acids were in the range 2·0 (glycine–aspartic acid) to 20·1 (alanine–glycine). The extractive and loading capability of the extractants for the amino acids was found to decrease in the order DNNSA>D2EHPA(S)>D2EHPA>Versatic 10, which follows the reverse order of their respective acid dissociation constants. DNNSA was shown to be a promising extractant for the extraction and fractionation of amino acids. © 1998 SCI     

Studies on Permeation of Nd (III) through Supported Liquid Membrane Using DNPPA + TOPO as Carrier

The transport behavior of Nd (III) through a supported liquid membrane (SLM) containing PTFE as support with organophosphorus extractant dinonyl phenyl phosphoric acid (DNPPA) carrier has been studied. The effect of neutral donors such as TOPO (tri-n-octyl phosphine oxide) TBP (tri-n-butyl phosphate), TEHP (tris 2-ethylhexyl phosphate) and Cyanex 923 (a mixture of four trialkyl phosphine oxides) in combination with DNPPA on transport of Nd (III) from HCl across SLM has been examined and the following trend was observed: TOPO > Cyanex 923 > TBP > TEHP. The effect of experimental variables such as feed acidity (0.5 to 5 M HCl), neodymium metal ion concentration (6.94 × 10^?4 to 6.94 × 10^?3 M), DNPPA concentration (0.2 to 0.6 M), stripping reagents in the receiving phase on Nd (III) transport across SLM were investigated. The percentage transport of Nd (III) was 97% after 6 hr run with 0.6 MDNPPA + 0.13 MTOPO as carrier. The permeability of Nd (III) decreased with increase in HCl and Nd (III) concentration in the feed solution. The transport of Nd (III) decreased with increase in membrane thickness as well as with decrease in pore size. Under optimized conditions transport behavior of other rare earths was also investigated independently, the trend observed was: La > Pr ≥ Nd > Sm > Eu > Gd > Tb > Dy > Ho > Er > Tm > Lu ≥ Y.     

Extraction and recovery of rhodamine B,methyl violet and methylene blue from industrial wastewater using D2EHPA as an extractant

The extraction behavior of cationic dyes namely rhodamine B (RB), methyl violet (MV) and methylene blue (MB) from industrial wastewater has been investigated using di-(2-ethylhexyl) phosphoric acid (D2EHPA) in hexane as a carrier. The extraction of cationic dyes increases with decreasing feed phase pH and increasing D2EHPA concentration in organic phase. The stripping percentage of dyes using acetic acid as the stripping agent from loaded D2EHPA was found to increase with increasing acid concentration. 98% stripping efficiency of dyes was achieved with 8.5 mol/L acetic acid solution at an organic:aqueous phase ratio (O/A) of 2:1. Parameters examined include D2EHPA concentration, effect of diluents, effect of pH, effect of initial dye concentration, equilibration time, and various stripping agents, aqueous to organic phase ratio in extraction and organic to aqueous phase ratio in stripping.     

Selective and Synergistic Extraction of Nickel from Simulated Cr-Ni Electroplating Bath Solutions using LIX 63 and D2EHPA as Carriers

The main goal of the present study is to explain synergistic extraction of nickel from simulated Cr-Ni electroplating bath solutions (SEBS) using 5,8-diethyl-7-hydroxydodecane-6-one oxime (LIX 63) and di-(2-ethylhexyl) phosphoric acid (D2EHPA) as extractants by emulsion liquid membrane (ELM) technique. The importance of membrane composition and aqueous phase properties on nickel extraction percentage has been highlighted for the selective extraction of nickel. Some important parameters like acid concentration, stripping solution type and concentration, mixing speed, extractant concentrations, phase ratio, and surfactant concentration was studied to improve the extraction and stripping efficiencies. Higher than > 99% of nickel was recovered at optimum conditions within 6 min. The higher separation factors (β_Ni/Cr) were obtained as 580. As a result, the nickel extraction kinetic with D2EHPA has been defined as faster than LIX63. So, the kinetic transport of nickel mainly depends on LIX63 than D2EHPA. According to these results, D2EHPA behaves as a synergistic extractant in the present extraction mechanism.     

Separation and Recovery of Cadmium from Acidic Leach Liquors of Spent Ni-Cd Batteries using Molten Paraffin Wax Solvent Extraction

Separation and recovery of cadmium from sulphate leach liquors of spent Ni-Cd batteries using TBP, HDEHP (D2EHPA), EHEHPA (PC 88A or Ionquest 801 or P507) have been investigated in a laboratory scale. Cadmium can be extracted into paraffin waxes from acidic solutions in the temperature range of 55–75°C using different extractants. The influence of various parameters on extraction and stripping were studied in detail. The feasibility of separation of cadmium from nickel using these extractants and their combination was studied. The mixture extractant of EHEHPA and TBP was found to be the best for the separation of Cd and Ni. A three-stage counter-current extraction simulation test for cadmium extraction was carried out at an A/O phase ratio of 4:1 and pH 2.5. More than 99.97% Cd²⁺ was extracted with the organic phase containing 0.7 mol L^?1 EHEHPA and 0.5 mol L^?1 TBP, while more than 99.97% nickel was left in the raffinate. The cadmium loaded organic phase was stripped with 2 mol L^?1 hydrochloric acid in the stripping stage. The present method can be applied to the separation and recovery of cadmium from acidic leach liquor of spent Ni-Cd batteries or related waste liquor.     

Synergic Extraction of Folic Acid with Di(2-ethylhexyl) Phosphoric Acid and Amberlite LA-2

The influences of extractants concentrations and solvent polarity on the efficiency of folic acid separation by synergic extraction with Amberlite LA-2 and di(2-ethylhexyl) phosphoric acid (D2EHPA) mixture have been analyzed. The results indicated the formation of an interfacial compound which includes one molecule of folic acid and one of D2EHPA, the hydrophobicity of this compound being increased by solvation with Amberlite LA-2 molecules. The number of aminic molecules participating in the interfacial complex formation is controlled by solvent polarity and D2EHPA concentration, decreasing from 3 to 1 with the increase of these two parameters. The results indicated that the most important synergic effect corresponds to the extractants mixture dissolved n-heptane, at low D2EHPA concentration in the organic phase (5 g/l).     

Synergistic Effect of D2EHPA and Cyanex 272 on Separation of Zinc and Manganese by Solvent Extraction

The effect of bis-2-ethylhexylphosphoric acid (D2EHPA), bis (2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272), and tri-butyl phosphate (TBP) and their mixtures in various proportions for the separation and extraction of zinc and manganese from sulfate solutions were investigated. Experiments were carried out in the pH range of 0.5–5.0 at 25, 40, and 60°C. It was shown that the extraction of zinc and manganese by D2EHPA and/or Cyanex 272 can be increased by the increase in pH and temperature. The synergistic extraction and separation of zinc and manganese with a mixture of D2EHPA and Cyanex 272 was studied and the results showed that mixing the two extractants improved the extraction capacity of the mixture. Increasing the D2EHPA to Cyanex 272 ratio in the organic phase, caused a right shifting of extraction isotherms of manganese and zinc; shifting the manganese curve was more than zinc. The manganese curve had considerable right shifting with 5% D2EHPA and 15% Cyanex 272. TBP did not affect the zinc (Zn) and manganese (Mn) extraction. The stoichiometric coefficients of Zn and Mn were determined with 20% and 5% D2EHPA and 15% Cyanex 272 by applying the slope analysis method. The organic phase was stripped by sulfuric acid.     

Studies on the Recovery of Uranium from Phosphoric Acid Medium by D2EHPA/n-Dodecane Supported Liquid Membrane

Abstract

Present studies deal with the application of supported liquid membrane (SLM) technique for the separation of uranium (VI) from phosphoric acid medium using Di-2 ethyl hexyl phosphoric acid (D2EHPA)/n-dodecane as a carrier and ammonium carbonate as a receiving phase. The studies involve the investigation of process controlling parameters like feed acidity of phosphoric acid, carrier concentration, stripping agents, and the effect of thickness and the pore size of the membrane. The transport of uranium decreases with increase in the concentration of phosphoric acid in feed solution whereas it increases with increase in carrier concentration in supported liquid membrane. More than 90% uranium (VI) is recovered in 360 minutes using 0.5 M D2EHPA/dodecane as carrier and 0.5 M ammonium carbonate as stripping phase from the 0.001 M H₃PO₄ feed. Lower concentration of phosphoric acid and higher carrier concentration is found to be the most suitable condition for maximum transport of uranium (VI) from its lean sources like commercial phosphoric acid and analytical wastes generated from the analysis of uranium by Volumetric (Davis-Gray) method.     

Synergistic effect of various neutral donors in D2EHPA for selective neodymium separation from lanthanide series via HFSLM

The separation of Nd(III) from lanthanide series via hollow fiber supported liquid membrane (HFSLM) using synergistic extractant was investigated. Optimum extraction and stripping obtained were 94.5% and 85.1% using D2EHPA and TOPO mixtures (0.5:0.5 M/M) as the synergistic extractant. Reaction order for both extraction and stripping were first-order with rate constants of 1.444 and 1.338 min⁻¹, respectively. The experimental results were used to correlate with the models. Results showed that the concentration of Nd(III) from the experiment fitted in well with the model results. The average deviation was 1.95% and 2.18% for predictions in both feed and stripping sides, respectively.     

THE EXTRACTION OF Eu(III) FROM ACIDIC MEDIA BY OCTYL(PHENYL)-N,N-DIISOBUTYL CARBAMOYLMETHYLPHOSPHINE OXIDE.

The extraction behavior of Eu(III) from nitric and hydrochloric acid By solutions of CMPO with and without TBP has been studied using mesitylene and dodecane as diluents. Compared to CMPO alone, the CMPO-TBP mixture shows a slight enhancement in the extraction of Eu(III) from nitric acid above 2M and lower DEu’ s from low acidity. The distribution ratios measured for Eu(III) between HN03 and CMPO-TBP in dodecane are higher than the corresponding values in mesitylene.Extractant dependency studies in the presence and absence of TBP show that at low HN03 concentrations, the extractant dependency curve obtained in the presence of TBP lies below the curve obtained in the absence of TBP. At high acidity, the opposite is observed. The extraction of Eu(III) from hydrochloric acid by CMPO-TBP in dodecane is much lower than from nitric acid. A comparison between CMPO and D2EHPA for Eu(III) extraction has been carried out.     

Solvent Extraction of Indium,Gallium, and Zinc Ions with Acidic Organophosphates having Bulky Alkyl Groups

The extraction equilibria of In³⁺, Ga³, and Zn²⁺ with bis(4‐ethylcyclohexyl)phosphoric acid (D4ECHPA), bis(4‐cyclohexylcyclohexyl)phosphoric acid (D4DCHPA), and bis(2‐ethylhexyl)phosphoric acid (D2EHPA) were investigated in acidic aqueous sulfate media. The order of extractability of metal ions is D4DCHPA > D2EHPA > D4ECHPA, which corresponds to the lipophilicity (log P) of the extractants. The separation factors, β_(In/Ga) and β_(Ga/Zn), of D4ECHPA and D4DCHPA are greater or comparable than that of D2EHPA, because of the steric hindrance of the bulky cyclohexyl groups. In³⁺ can be therefore separated from simulated liquor containing a high concentration of Zn²⁺ by D4DCHPA.     

Process for the Recovery of Cobalt and Nickel from Sulphate Leach Liquors with Saponified Cyanex 272 and D2EHPA

Abstract

In this paper, a process is reported for the recovery of cobalt and nickel from copper raffinate solutions using partially saponified Cyanex 272 and D2EHPA as the extractants. The aqueous feed contains 1.65 g/L cobalt and 16.42 g/L nickel. More than 99.9% cobalt separation was achieved with 0.13 M Cyanex 272 (60% neutralized with alkali) in two counter‐current stages at an aqueous to organic phase ratio of 1.1:1. Co‐extraction of nickel was 0.18% only. Stripping of cobalt from a loaded organic phase was carried out with synthetic spent electrolyte solution at an organic to aqueous phase ratio of 2.5 in two counter‐current stages to generate a pregnant electrolyte solution to produce cobalt metal by electrowinning. Similarly, optimum conditions for nickel extraction with 60% neutralized 1 M D2EHPA at O/A ratio of 1.4 in 2 two stages and stripping of metal with synthetic spent electrolyte at O/A ratio of 1.6 in two stages were standardized. Extraction and stripping efficiencies were >99% and the flowsheet of the process is demonstrated.