Removal of Basic Dye Crystal Violet from Aqueous Solution by Cu(II)-Loaded Montmorillonite

The effects of contact time, reaction temperature, and ionic strength on crystal violet adsorption onto Cu(II)-loaded montmorillonite were studied. The kinetic experimental data were analyzed using pseudo-first-order, pseudo-second-order, and Elovich equations to examine the adsorption mechanism. The result suggested that the adsorption was best represented by the pseudo-second-order equation. The suitability of the Langmuir, Freundich, and Temkin isotherms to equilibrium data was also investigated at 25°C. The maximum adsorption capacity was 114.3 mg dye/g Cu(II)-loaded montmorillonite at adsorbent concentration 1 g/L. The differential heat of adsorption was evaluated and the result showed that adsorption of crystal violet onto the Cu-loaded sample was chemical in nature. The ionic strength and reaction temperature exhibited an insignificant impact on the crystal violet adsorption. The Cu(II)-loaded montmorillonite could serve as low-cost adsorbents for removing crystal violet from aqueous solution compared to the data reported in the literature.     

Polyamine Functionalized Magnetite Nanoparticles as Novel Adsorbents for Cu(II) Removal from Aqueous Solutions

Three novel magnetic adsorbents were synthesized through the immobilization of di-, tri-, and tetraamine onto the surface of silica coated magnetite nanoparticles. The adsorbents were characterized by XRD patterns, FTIR spectroscopy, elemental and thermogravimetric analysis, magnetic measurements, SEM/TEM, EDX spectroscopy, and N₂ adsorption/desorption isotherms. Their capacity to remove copper ions from aqueous solutions was investigated and discussed comparatively. The equilibrium data were analyzed using Langmuir and Freundlich isotherms. The kinetics was evaluated using the pseudo-first-order, pseudo-second-order, and intra-particle diffusion models. The best interpretation for the equilibrium data was given by the Langmuir isotherm for the tri- and tetraamine functionalized adsorbents, while for the diamine functionalized adsorbent the Freundlich model seemed to be better. The kinetic data were well fitted to the pseudo-second-order model. The overall rate of adsorption was significantly influenced by external mass transfer and intraparticle diffusion. It was observed that the adsorption capacity at room temperature decreased as the length of polyamine chain immobilized on the adsorbent surface increased, the maximum adsorption capacities being 52.3 mg g^?1 for 1,3-diaminopropan functionalized adsorbent, 44.2 mg g^?1 for diethylenetriamine functionalized adsorbent, and 39.2 mg g^?1 for triethylenetetramine functionalized adsorbent. The sorption process proved to be highly dependent of pH. The results of the present work recommend these materials as potential candidates for copper removal from aqueous solutions.     

Adsorption kinetics and mechanism of cationic methyl violet and methylene blue dyes onto sepiolite

The use of low-cost and ecofriendly adsorbents was investigated as an ideal alternative to the current expensive methods of removing dyes from wastewater. Sepiolite was used as an adsorbent for the removal of methyl violet (MV) and methylene blue (MB) from aqueous solutions. The rate of adsorption was investigated under various parameters such as contact time, stirring speed, ionic strength, pH and temperature for the removal of these dyes. Kinetic study showed that the adsorption of dyes on sepiolite was a gradual process. Quasi-equilibrium reached within 3 h. Adsorption rate increased with the increase in ionic strength, pH and temperature. Pseudo-first-order, the Elvoich equation, pseudo-second-order, mass transfer and intra-particle diffusion models were used to fit the experimental data. The sorption kinetics of MV and MB onto sepiolite was described by the pseudo-second-order kinetic equation. Intra-particle diffusion process was identified as the main mechanism controlling the rate of the dye sorption. The diffusion coefficient, D, was found to increase when the ionic strength, pH and temperature were raised. Thermodynamic activation parameters such as ΔG¹, ΔS¹ and ΔH¹ were also calculated.     

A comparative study of removal of Cu(II) from aqueous solutions by locally low-cost materials: marine macroalgae and agricultural by-products

In this study, adsorption of Cu(II) onto the five locally abundantly low-cost biosorbents (Laminaria japonica, P. yezoensis Ueda, rice bran, wheat bran and walnut hull) was investigated depending on initial solution pH, contact time, adsorbent concentration and reaction temperature. Cu(II) removal was pH-dependent for various biosorbents investigated. For P. yezoensis Ueda, rice bran, wheat bran and walnut hull, the batch equilibrium data were correlated to Langmuir and Freundlich isotherms and the data fitted better to the Langmuir isotherm equation and yielded Langmuir monolayer capacity of 5.04, 10.41, 6.85 and 3.52 mg/g at the temperature of 20°C, respectively. In the case of Laminaria japonica, the equilibrium data obeyed the Hill-der Boer equation for the whole initial concentration ranges of 0–200 mg/L examined, but only to Langmuir and Freundlich equations for the initial concentration less than 120 mg/L at various temperatures. The apparent thermodynamic parameters were calculated for each of the five biosorbents (ΔH = 9.25–40.04 kJ/mol; ΔG = –17.60 to –24.16 kJ/mol and ΔS = 85.81–228 J/mol K). The numerical values obtained showed that Cu(II) adsorption is a spontaneous, entropy-driven and endothermic process. The batch kinetic data were correlated to the pseudo-first order and pseudo-second order models and the data fitted better to the pseudo-second order equation (the pseudo-second order rate constants, k_2,e = 0.1059–0.9453 g/(mg min); the correlation coefficients, r = 0.9816–0.9993).     

Removal of basic dyes from aqueous solution by low-cost adsorbent: Wood apple shell (Feronia acidissima)

The adsorption of two basic dyes, methylene blue (MB) and crystal violet (CV) on wood apple shell (WAS) were investigated using a batch adsorption technique. A series of experiments were undertaken in an agitated batch adsorber to assess the effect of the system variables such as solution pH, dye concentration and temperature. Removal of dyes was observed to be most effective at higher pH. Freundlich and Langmuir isotherm models were applied to the equilibrium data. The results showed that Langmuir equation fits better than the Freundlich equation. It was observed that the WAS adsorbent showed higher adsorption capacity for crystal violet (130 mg/g) than methylene blue (95.2 mg/g). The FTIR studies indicate that the interaction of dye and WAS surface is via the nitrogen atoms of the adsorbate and oxygen groups of the adsorbent. The adsorption of dyes onto WAS proceeds according to a pseudo-second-order model. Thermodynamic parameters such as free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were also calculated. The studies show that WAS, a lignocellulosic inexpensive material, can be an alternative to other expensive adsorbents used for dye removal in wastewater treatment.     

EFFECT OF TEMPERATURE ON THE ADSORPTION OF METHYLENE BLUE DYE ONTO SULFURIC ACID–TREATED ORANGE PEEL

The present study explains the preparation and application of sulfuric acid–treated orange peel (STOP) as a new low-cost adsorbent in the removal of methylene blue (MB) dye from its aqueous solution. The effects of temperature on the operating parameters such as solution pH, adsorbent dose, initial MB dye concentration, and contact time were investigated for the removal of MB dye using STOP. The maximum adsorption of MB dye onto STOP took place in the following experimental conditions: pH of 8.0, adsorbent dose of 0.4 g, contact time of 45 min, and temperature of 30°C. The adsorption equilibrium data were tested by applying both the Langmuir and Freundlich isotherm models. It is observed that the Freundlich isotherm model fitted better than the Langmuir isotherm model, indicating multilayer adsorption, at all studied temperatures. The adsorption kinetic results showed that the pseudo-second-order model was more suitable to explain the adsorption of MB dye onto STOP. The adsorption mechanism results showed that the adsorption process was controlled by both the internal and external diffusion of MB dye molecules. The values of free energy change (ΔG ^o) and enthalpy change (ΔH ^o) indicated the spontaneous, feasible, and exothermic nature of the adsorption process. The maximum monolayer adsorption capacity of STOP was also compared with other low-cost adsorbents, and it was found that STOP was a better adsorbent for MB dye removal.     

Lead(II) Adsorption onto Sulphuric Acid Treated Cashew Nut Shell

In this study, sulphuric acid treated cashew nut shell (STCNS) was used as adsorbent for the removal of lead(II) ions from the aqueous solutions. Adsorption studies were performed by varying the solution pH, contact time, and temperature. Experimental data were analyzed by the model equations such as Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherms and it was found that the Freundlich isotherm model fits best with the experimental data at different temperatures studied. The maximum adsorption capacity of lead(II) on STCNS was determined as 408.6, 432, 446.3, and 480.5 mg/g, respectively, at different temperatures (30, 40, 50, and 60°C). The thermodynamic parameters (ΔG^o, ΔH^o, and ΔS^o) were calculated and the thermodynamic properties of lead(II) ions-STCNS system indicate the exothermic process. Adsorption kinetic constants were determined using pseudo-first-order, pseudo-second-order, and the Elovich kinetic models at various temperatures. The adsorption results clearly showed that the adsorption of lead(II) ions onto STCNS followed pseudo-second-order model and the adsorption was both by film diffusion and by intraparticle diffusion. A single-stage batch adsorber was designed using the Freundlich equation.     

ADSORPTION,KINETICS, AND EQUILIBRIUM STUDIES ON REMOVAL OF 4,4-DDT FROM AQUEOUS SOLUTIONS USING LOW-COST ADSORBENTS

The removal of a chlorinated pesticide (4,4-DDT) from aqueous solutions by a batch adsorption technique using different low-cost adsorbents was investigated. Two adsorbents, wood sawdust (A) and cork wastes (B), were used to determine adsorption efficiency. The influence of the adsorbent particle size and the organic matter of water (humic acids) on the removal process was studied. The obtained results were compared to those obtained with a commercial powdered activated carbon (PAC, F400, Chemviron) (C). Kinetic studies were performed to understand the mechanistic steps of the adsorption process. The rate of the adsorption kinetics of 4,4-DDT on the low-cost adsorbents was found best fitted with a pseudo-second-order kinetic model. This is in contrast to the rate of the adsorption kinetics of the PAC F400, which was best fitted with the Lagergren model. The application of the Morris-Weber equation showed that the adsorption process of 4,4-DDT on these adsorbents was complex. Both the adsorption on the surface and the intraparticle diffusion were the rate-controlling mechanisms. Langmuir and Freundlich adsorption isotherms were applicable to the adsorption process and their constants were evaluated. The adsorption capacity (q_m) calculated from the Langmuir isotherm (69.44 mg·g^?1, 19.08 mg·g^?1, and 163.90 mg·g^?1, respectively, for A, B, and C) showed that the process is highly particle size dependent, that the organic matter influenced the adsorption process negatively, and that wood sawdust is the most effective adsorbent for the removal of 4,4-DDT from aqueous solutions. The adsorbents studied exhibited a possible application in water decontamination, as well as in treatment of industrial and agricultural waste waters.     

Equilibrium and Thermodynamic Studies on the Removal and Recovery of Safranine-T Dye from Industrial Effluents

In this study, deoiled-mustard obtained from local oil mills has been used as an inexpensive and effective adsorbent for the removal of Safranine-T dye from wastewater. The influence of various factors on the adsorption capacity has been studied by batch experiments. The adsorption studies revealed that the ongoing adsorption validates Langmuir adsorption isotherms better than the Freundlich adsorption isotherm at temperatures 40, 50, 60°C. Thermodynamic parameters such as ΔG°, ΔH°, and ΔS° for the adsorption process were calculated. Desorption profile revealed that a significant portion (83%) of the dye could be desorbed by using 12% acetic acid solution as an eluting agent. A comparative analysis of the adsorption capacities of various adsorbents reveals the superior performance of the adsorbent under study. The results indicated that deoiled-mustard is a good and low-cost adsorbent from the practical point of view for dyes removal and can be used as an economically viable alternative to commercial activated carbon.     

Removal of Crystal Violet Dye from Aqueous Solution Using Calcined and Uncalcined Mixed Clay Adsorbents

In this work, calcined and uncalcined mixed clays containing kaolin, ball clay, feldspar, pyrophyllite, and quartz are examined as a potential adsorbent for the removal of crystal violet dye from aqueous solution. These clays are characterized by nitrogen adsorption/desorption isotherms, X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, and thermo gravimetric analysis (TGA). The kinetics and thermodynamic parameters as well as the effects of the pH, the temperature, and the adsorbent dosage have also been investigated. The experimental results indicate that the Langmuir model expresses the adsorption isotherm better than the Freundlich model. The obtained result showed a tremendous increase in the crystal violet adsorption capacity (1.9 × 10^?3 mol g^?1) after calcination, which is one order greater than that of the uncalcined mixed clay. The mechanism of the adsorption process is elucidated on the basis of experimental data. The percentage removal of crystal violet dye increases with increasing the pH, the temperature, and the adsorbent dosage. The investigation of kinetic studies indicates that the adsorption of crystal violet on calcined and uncalcined mixed clays could be described by the pseudo-second-order model. The negative Δ G ⁰ values obtained from the thermodynamic investigation confirm that the adsorption is spontaneous in nature. The adsorption results suggest that the calcined and uncalcined mixed clays can also be used as low cost alternatives to the expensive activated carbon for the removal of dyes from aqueous solution.     

Kinetics and thermodynamic studies of Cr(VI) adsorption using environmental friendly multifunctional zeolites synthesized from coal fly ash under mild conditions

Abstract

The Na-P1 zeolite was produced from coal fly ash and modified with different environmental friendly surfactants. The potential of these green modified zeolites was investigated as adsorbents for Cr(VI) ions in a batch system. XRD, SEM, XRF, and ICP-AES analyses were used for the characterization of raw materials and zeolite samples. The environmental friendly modified zeolites successfully immobilized different toxic elements in their framework inhibiting the transfer of these toxic elements to the surrounding liquid phase. The effects of various operational parameters on Cr(VI) removal were studied. The Hexamethylenediamine (HDTMA) and Ammonyx KP (KP) modified zeolites had larger chromium removal potential than the other samples at all temperatures. The effectiveness of Cr(VI) ions elimination became greater as the pH decreased and the adsorbent dose increased. The Freundlich, Langmuir, and Dubinin–Radushkevich isotherms were fitted to the equilibrium data. The Dubinin–Radushkevich and Langmuir models gave a better fitness to equilibrium data of HDTMA-Na-P1 and KP-Na-P1, respectively. The positive and high ΔH° values showed the endothermic nature of the total Cr(VI) sorption procedure and indicated that Cr(VI) adsorption onto HDTMA-Na-P1 and KP-Na-P1 is a chemisorption. The negative ΔS° values also showed that chromium ions were stable on the surface of adsorbents. The adsorption potential of the developed eco-friendly KP-Na-P1 was higher than those of other adsorbents reported in the literature.     

Kinetic and isothermal studies of lead ion adsorption onto bentonite

The use of bentonite for the removal of Pb(II) from aqueous solutions for different contact times, pH of suspension, and initial concentration of Pb and particle sizes of absorbent was investigated. Batch adsorption kinetic experiments revealed that the adsorption of Pb(II) onto bentonite involved fast and slow processes. The adsorption mechanisms in the lead/bentonite system followed pseudo-second-order kinetics with a significant contribution of film diffusion. The adsorption isotherms were described by means of the Langmuir and Freundlich isotherms and the Langmuir model represented the adsorption process better than the Freundlich model. The maximum adsorption capacity of Pb(II) onto natural bentonite was 78.82 mg g^− 1.     

Kinetics and equilibrium studies of removal of an azo dye from aqueous solution by adsorption onto scallop

In the present work removal of an azo dye (Reactive Black 5) was investigated from aqueous solution by adsorption onto scallop as a low-cost and widely available adsorbent. The effect of various operational parameters, such as contact time, pH, initial dye concentration and adsorbent dosage on the removal efficiency of dye was studied. Removal efficiency declined with the increase in solution pH and initial dye concentration but with the decrease in adsorbent dosage. Experimental equilibrium and kinetics data were fitted by Langmuir and Freundlich isotherms and pseudo-first-order and pseudo-second-order kinetic models, respectively.     

Adsorption of methylene blue from aqueous solution onto multiporous palygorskite modified by ion beam bombardment: Effect of contact time,temperature, pH and ionic strength

Our previous work has reported that an inorganic nano-network of palygorskite with multiporous structure can be fabricated from rigid nano-rods by ion beam bombardment and has better adsorption capability than nano-rods. Here, this dispersed modified nano adsorbent was characterized by Fourier Transform Infrared (FTIR) spectroscopy and Scanning Electron Microscope (SEM). The adsorption property of methylene blue (MB) onto this adsorbent was investigated. It was found that the adsorption capacity increased with contact time, pH, MB initial concentration, respectively, and then reached an equilibrium. Moreover, the effect of pH on the adsorption was strongly determined by zeta potential. The adsorption kinetics of MB was dominated by the pseudo-second-order reaction model, and the adsorption isotherms fit the Freundlich isotherms better than the Langmuir isotherms. Three temperatures (293 K, 303 K, 313 K) were set for describing the thermodynamic parameters (ΔH^θ, ΔS^θ, and ΔG^θ), which indicated that the adsorption was spontaneous and exothermic. Lastly, the mechanism of the influence of ionic strength on the adsorption was discussed.     

Kinetic and equilibrium studies of Pb(II) and Cd(II) removal from aqueous solution onto colemanite ore waste

The adsorption characteristics of Pb(II) and Cd(II) onto colemanite ore waste (CW) from aqueous solution were investigated as a function of pH, adsorbent dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the adsorption isotherms. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The adsorption capacity of CW was found to be 33.6 mg/g and 29.7 mg/g for Pb(II) and Cd(II) ions, respectively. Analyte ions were desorbed from CW using both 1 M HCl and 1 M HNO₃. The recovery for both metal ions was found to be higher than 95%. The mean adsorption energies evaluated using the D-R model indicated that the adsorption of Pb(II) and Cd(II) onto CW were taken place by chemisorption. The thermodynamic parameters (ΔG^o, ΔH^o and ΔS^o) showed that the adsorption of both metal ions was feasible, spontaneous and exothermic at 20-50 °C. Adsorption mechanisms were also investigated using the pseudo-first-order and pseudo-second-order kinetic models. The kinetic results showed that the adsorption of Pb(II) and Cd(II) onto CW followed well pseudo-second order kinetics.     

Study of the adsorption of phenol by two soils based on kinetic and isotherm modeling analyses

Various natural adsorbents, which have been in used for removal of pollutants, in general, and phenol, in particular, are mostly directed towards improving the adsorption capacity of the adsorbents by various pretreatments (chemical, thermal or biological), which necessarily lead to increase in the cost as well as in the level of difficulties in regeneration/disposal of the adsorbent. The present studies, on the other hand, are aimed towards evaluating the feasibility of using two common soils as potential low-cost adsorbents for the removal of phenol from its aqueous solution, in their natural forms (i.e., without any pretreatment). Accordingly, experiments were carried out (in batch mode) for optimization of the adsorption parameters (such as pH, contact time, equilibrium time and adsorbent dosage), for varying initial phenol concentrations. The results showed that the maximum phenol adsorption capacity was found at pH ~6, under a constant temperature of 30 ± 2 °C (at 6-hour equilibrium period). Several kinetic models (viz. Lagergren first-order, pseudo-second-order, Elovich and intra-particle diffusion) as well as isotherm models (Langmuir, Freundlich, Redlich and Peterson and Sip) were applied to the experimental data. The pseudo-second-order model was found to be the most suitable model describing the adsorption of phenol by two soils (which indicated this adsorption as a chemisorption process). On analysis of equilibrium isotherms for the adsorption of phenol by two soils, Redlich-Peterson and Sip isotherms were found to be the best representative for phenol-sorption on two selected, soil adsorbents.     

Palladium,silver, and zinc oxide nanoparticles loaded on activated carbon as adsorbent for removal of bromophenol red from aqueous solution

The adsorption of bromophenol red (BPR) onto three adsorbents including palladium, silver and zinc oxide nanoparticles loaded on activated carbon (Pd-NP-AC, Ag-NP-AC and ZnO-NP-AC) in a batch system has been studied and the influence of various parameters has been optimized. The influence of time on removal of BPR on all adsorbent was investigated and experimental data were analyzed by four kinetic models including pseudo first and second-order, Elovich and the intraparticle diffusion equations. Following fitting the experimental data to these models, the respective parameters of each model such as rate constants, equilibrium adsorption capacities and correlation coefficients for each model were investigated and based on well known criterion their applicability was judged. It was seen that the adsorption of BPR onto all adsorbents sufficiently described by the pseudo second-order equation in addition to interparticle diffusion model. The adsorption of BPR on all adsorbent was investigated at various concentration of dye and the experimental equilibrium data were analyzed and fitted to the Langmuir, Freundlich, Tempkin, Dubinin, and Radushkevich equations. A single stage in batch process was efficient and suitable for all adsorbents using the Langmuir isotherm with maximum adsorption of 143 mg g^?1 for Pd-NP-AC, 250 mg g^?1 for Ag-NP-AC and 200 mg g^?1 for ZnO-NR-AC. Thermodynamic parameters such as ΔG°, ΔH°, and ΔS° for Pd-NP-AC adsorbent were calculated.     

Effect of nickel coating on carbon for adsorption of cadmium from aqueous solutions

Nickel was coated on carbon and it was characterized by SEM and XRD. Sorption of Cd(II) ions onto carbon and nickel‐coated carbon (Ni/C), effect of acids, pH, shaking time, loading capacity, and adsorbent weight has been investigated. Acids reduce sorption and maximum sorption takes place from deionized water and R_d values for carbon and Ni/C in deionized water are 212.9 ± 0.9 and 232.5 ± 2.5. The sorption data followed the Freundlich, Dubinin–Radushkevich (D–R), isotherms and different parameters have been calculated. Sorption free energy values have been calculated and are 12.56 ± 0.19 and 14.84 ± 0.196 for carbon and Ni/C and indicate that adsorption process is chemisorption. Increase in adsorption shows the increase in catalytic activity of the adsorbent. The variation of sorption with temperature has been used to calculate the values of ΔH, ΔS, and ΔG for Cd(II) sorption. These values show that adsorption of Cd(II) ions on the adsorbents is endothermic, spontaneous, and entropy driven. Coating of carbon with nickel has improved its adsorption properties. Adsorption behaviour provides useful information for the catalytic activity of catalysts.     

Investigation of α‐iron oxide‐coated polymeric nanocomposites capacity for efficient heavy metal removal from aqueous solution

In the present study, PS@α‐Fe₂O₃ nanocomposites were prepared by chemical microemulsion polymerization approach and the ability of magnetic beads to remove Cu(II) ions from aqueous solutions in a batch media was investigated. Various physico‐chemical parameters such as pH, initial metal ion concentration, temperature, and equilibrium contact time were also studied. Adsorption mechanism of Cu²⁺ ions onto magnetic polymeric adsorbents has been investigated using Langmuir, Freundlich, Sips and Redlich–Petersen isotherms. The results demonstrated that the PS@α‐Fe₂O₃ nanocomposite is an effective adsorbent for Cu²⁺ ions removal. The Sips adsorption isotherm model (R² > 0.99) was more in consistence with the adsorption isotherm data of Cu(II) ions compared to other models and the maximum adsorbed amount of copper was 34.25 mg/g. The adsorption kinetics well fitted to a pseudo second‐order kinetic model. The thermodynamic parameters (ΔH°, ΔS°, and ΔG°) were calculated from the temperature dependent sorption isotherms, and the results suggested that copper adsorption was a spontaneous and exothermic process. POLYM. ENG. SCI., 55:2735–2742, 2015. © 2015 Society of Plastics Engineers     

Removal of Boron from Aqueous Solutions by Adsorption Using Fly Ash,Zeolite, and Demineralized Lignite

In the present study for the purpose of removal of boron from water by adsorption using adsorbents like fly ash, natural zeolite, and demineralized lignite was investigated. Boron in water was removed with fly ash, zeolite, and demineralized lignite with different capacities. Ninety-four percent boron was removed using fly ash. Batch experiments were conducted to test the removal capacity, to obtain adsorption isotherms, thermodynamic and kinetic parameters. Boron removal by all adsorbents was affected by pH of solution; maximum adsorption was achieved at pH 10. Adsorption of boron on fly ash was investigated by the Langmuir, Freundlich, and the Dubinin-Radushkevich models. Standard entropy and enthalpy changes of adsorption of boron on fly ash were, ΔS ⁰  = ?0.69 kJ/mol K and ΔH ⁰  = ?215.34 kJ/mol, respectively. The negative value of ΔS ⁰ indicated decreased randomness at the solid/solution interface during the adsorption boron on the fly ash sample. Negative values of ΔH ⁰ showed the exothermic nature of the process. The negative values of ΔG ⁰ implied that the adsorption of boron on fly ash samples was spontaneous. Adsorption of boron on fly ash occurred with a pseudo-second order kinetic model, and intraparticle diffusion of boron species had also some effect in adsorption kinetics.