Polyamine Functionalized Magnetite Nanoparticles as Novel Adsorbents for Cu(II) Removal from Aqueous Solutions

Three novel magnetic adsorbents were synthesized through the immobilization of di-, tri-, and tetraamine onto the surface of silica coated magnetite nanoparticles. The adsorbents were characterized by XRD patterns, FTIR spectroscopy, elemental and thermogravimetric analysis, magnetic measurements, SEM/TEM, EDX spectroscopy, and N₂ adsorption/desorption isotherms. Their capacity to remove copper ions from aqueous solutions was investigated and discussed comparatively. The equilibrium data were analyzed using Langmuir and Freundlich isotherms. The kinetics was evaluated using the pseudo-first-order, pseudo-second-order, and intra-particle diffusion models. The best interpretation for the equilibrium data was given by the Langmuir isotherm for the tri- and tetraamine functionalized adsorbents, while for the diamine functionalized adsorbent the Freundlich model seemed to be better. The kinetic data were well fitted to the pseudo-second-order model. The overall rate of adsorption was significantly influenced by external mass transfer and intraparticle diffusion. It was observed that the adsorption capacity at room temperature decreased as the length of polyamine chain immobilized on the adsorbent surface increased, the maximum adsorption capacities being 52.3 mg g^?1 for 1,3-diaminopropan functionalized adsorbent, 44.2 mg g^?1 for diethylenetriamine functionalized adsorbent, and 39.2 mg g^?1 for triethylenetetramine functionalized adsorbent. The sorption process proved to be highly dependent of pH. The results of the present work recommend these materials as potential candidates for copper removal from aqueous solutions.     

Adsorption Characteristics of Congo Red from Aqueous Solution onto Tea Waste

The feasibility of using tea waste (TW) as a low-cost adsorbent for the adsorption of an anionic dye (Congo red) from aqueous solution has been investigated. Adsorption in a batch process was conducted to study the effect of adsorbent dosage, initial dye concentration, contact time, pH, and temperature. The experimental data were analyzed by the Langmuir, Freundlich, and Temkin models. The adsorption system was best described by the Langmuir isotherm (R ² > 0.99). Adsorption kinetics followed a pseudo-second-order model (R ² > 0.99). The effect of mechanical treatment (vibratory mill) was also studied. The experimental results showed that using this physical treatment leads to an increase in the adsorption capacity of TW from 32.26 to 43.48 mg/g. Thermodynamic analyses revealed that the adsorption of Congo red on TW was endothermic and spontaneous in nature. The results indicated that TW can be employed as a potential low-cost adsorbent for the removal of Congo red from aqueous solution.     

Synthesis and characterization of a novel Ca-alginate-biochar composite as efficient zinc (Zn2+) adsorbent: Thermodynamics,process design,mass transfer and isotherm modeling

In this present work, Ca-alginate-biochar adsorbent has been synthesized, characterized and tested its effectiveness in the removal of aqueous phase Zn²⁺ metal. The removal efficiency was studied under various physicochemical process parameters. External mass transfer model, intraparticle diffusion model and pseudo-first-order and pseudo-second-order models were used to fit the experimental Zn²⁺ adoption kinetic results and to identify the mechanism of adsorption. The desorption studies indicate the possibilities of ion-exchange and physical–chemical adsorption of Zn^2+. The adsorption was best described by Langmuir isotherm model. Thermodynamic parameters suggested that the adsorption process becomes spontaneous, endothermic and irreversible in nature.     

Adsorptive removal of cationic dye from aqueous solutions by ZnO/ZnMn2O4 nanocomposite

The ZnO/ZnMn₂O₄ nanocomposite (ZnMn) was used as adsorbent for the removal of cationic dye Basic Yellow 28 (BY28) from aqueous solutions. The adsorbent was characterized by X-ray diffraction, scanning electron microscope, TEM, Fourier transform infrared ray, BET, particle size distribution and zeta potential measurements. The adsorption parameters, such as temperature, pH and initial dye concentration, were studied. Kinetic adsorption data were analyzed using the pseudo-first-order, pseudo-second-order and intraparticle diffusion kinetic models. The Langmuir and Freundlich isotherm models were applied to fit the equilibrium data. The maximum adsorption capacity of BY28 was 48.8 mg g^?1. Various thermodynamic parameters, such as ΔG°, ΔH° and ΔS°, were calculated.     

Removal of chlorinated phenol from aqueous solution utilizing activated carbon derived from papaya (<Emphasis Type="Italic">Carica Papaya</Emphasis>) seeds

Activated carbons (ACs) were prepared from papaya seeds with different dry weight impregnation ratios of zinc chloride (ZnCl₂) to papaya seeds by using a two-stage self-generated atmosphere method. The papaya seeds were first semi-carbonized in a muffle furnace at 300 °C for 1 h and then impregnated with ZnCl₂ before activation at 500 °C for 2 h. Several physical and chemical characteristics such as moisture, ash, pH, functional groups, morphological structure and porosity of prepared ACs were studied and presented here. AC2, with the impregnation ration of 1: 2 (papaya seeds: ZnCl₂), yielded a product that had the highest adsorption capacity, 91.75%, achieved after 180min contact time. The maximum Brunauer, Emmett and Teller (BET) surface area of AC2 was 546m²/g. Adsorption studies indicated that AC2 complied well with the Langmuir isotherm (q _m =39.683mg g^?1) and the pseudo-second-order (q _e =29.36mg g^?1). This indicated that chemisorption was the primary adsorption method for AC2. The intraparticle diffusion model proved that the mechanism of adsorption was separated into two stages: the instantaneous stage and the gradual adsorption stage. Overall, this work demonstrated the suitability of using papaya seeds as a precursor to manufacture activated carbon.     

Aqueous Phase Adsorption of Cephalexin onto Bentonite and Activated Carbon

The adsorption of cephalexin in aqueous solution has been investigated using bentonite and activated carbon as the adsorbents. Batch kinetics and isotherm studies were carried out to evaluate the effect of contact time, adsorbent dosage, pH, particle size, and temperature. Adsorption equilibrium data were well represented by the Langmuir and Freundlich isotherm models. The adsorption intensity was found to be increased as the aqueous phase pH increased, and had a maximum at pH = 6.1. The pseudo-first order, pseudo-second order, and intraparticle diffusion kinetic models were used to describe the kinetic data. The experimental data fitted very well with the pseudo-second-order kinetic model and also followed the simple external and intraparticle model.     

Removal of methylene blue from aqueous solutions by adsorption onto chemically activated halloysite nanotubes

This study examines the adsorption behavior of methylene blue (MB) from aqueous solutions onto chemically activated halloysite nanotubes. Adsorption of MB depends greatly on the adsorbent dose, pH, initial concentration, temperature and contact time. The Langmuir and Freundlich models were applied to describe the equilibrium isotherms and the Langmuir model agrees very well with experimental data. The maximum adsorption capacities for MB ranged from 91.32 to 103.63 mg·g⁻¹ between 298 and 318 K. A comparison of kinetic models applied to the adsorption data was evaluated for pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion equation. The results showed the adsorption process was well described by the pseudo-second-order and intra-particle diffusion mode. Thermodynamic parameters suggest that the adsorption is spontaneous and endothermic. The obtained results indicated that the product had the potential to be utilized as low-cost and effective alternative for dye removal in wastewater.     

Adsorption of Textile Dye on Zinc Stannate Oxide: Equilibrium,Kinetic and Thermodynamics Studies

Zn₂SnO₄ powder was prepared by hydrothermal process at 200°C for 12 h. The material was characterized by X-ray-diffraction and surface area. The synthesized sample presented a pure phase and a surface area of 48.8 m² · g^?1. It was used as adsorbent to remove the Reactive Red 141 that is a azo textile dye. The adsorption kinetics of the textile dye on Zn₂SnO₄ followed the pseudo-second-order model. The adsorption process was found to be controlled by both external mass transfer and intraparticle diffusion. The equilibrium data were in good agreement with both Langmuir and Freundlich isotherms. Thermodynamic parameters were calculated, and the results revealed that the adsorption process is endothermic in nature, with weak forces of the Van der Walls acting.     

Removal of Orange II by Phosphonium-modified Algerian Bentonites

An Algerian montmorillonite was modified with two organic surfactants, methyltriphenyl phosphonium bromide and n-hexyltriphenyl phosphonium bromide. The solids obtained were used as adsorbents to remove Orange II, an anionic dye from aqueous solutions. Batch experiments were conducted to study the effects of temperature (20–60°C), initial concentration of adsorbate (50–150 mg L^?1) and pH of solution 6.5 on dye adsorption. Due to their organophilic nature, exchanged montmorillonites were able to adsorb Orange II at a very high level. Adsorption of Orange II for B-NHTPB and B-MTPB at different pH show that the adsorption capacity clearly decreases with an increase in pH of the initial solution from 2 to 8, this decrease being dramatic for pH > 8. This may be due to hydrophobic interactions of the organic dye with both phosphonium molecules and the remaining non-covered portion of siloxane surface. The kinetics of the adsorption was discussed on the basis of three kinetic models, i.e., the pseudo-first-order, the pseudo-second-order, and the intraparticle diffusion models. Equilibrium is reached after 30 min and 60 min for B-MTPB and B-NHTPB, respectively; the pseudo-second-order kinetic model described very well the adsorption of Orange II on modified bentonites. The non-linear Langmuir model provided the best correlation of experimental data, maximum adsorption of Orange II is 53.78 mg g^?1 for B-NHTPB and 33.79 mg g^?1 for B-MTPB. The thermodynamic parameters, such as free energy of adsorption (ΔG°), enthalpy change (ΔH°), and entropy change (ΔS°) were also determined and evaluated. From thermodynamic studies, it was deduced that the adsorption was spontaneous and exothermic.     

Comparison of Cr(VI) Adsorption Using Synthetic Schwertmannite Obtained by Fe3+ Hydrolysis and Fe2+ Oxidation: Kinetics,Isotherms and Adsorption Mechanism

Good sorption properties and simple synthesis route make schwertmannite an increasingly popular adsorbent. In this work, the adsorption properties of synthetic schwertmannite towards Cr(VI) were investigated. This study aimed to compare the properties and sorption performance of adsorbents obtained by two methods: Fe³⁺ hydrolysis (SCH_A) and Fe²⁺ oxidation (SCH_B). To characterise the sorbents before and after Cr(VI) adsorption, specific surface area, particle size distribution, density, and zeta potential were determined. Additionally, optical micrographs, SEM, and FTIR analyses were performed. Adsorption experiments were performed in varying process conditions: pH, adsorbent dosage, contact time, and initial concentration. Adsorption isotherms were fitted by Freundlich, Langmuir, and Temkin models. Pseudo-first-order, pseudo-second-order, intraparticle diffusion, and liquid film diffusion models were used to fit the kinetics data. Linear regression was used to estimate the parameters of isotherm and kinetic models. The maximum adsorption capacity resulting from the fitted Langmuir isotherm is 42.97 and 17.54 mg·g⁻¹ for SCH_A and SCH_B. Results show that the adsorption kinetics follows the pseudo-second-order kinetic model. Both iron-based adsorbents are suitable for removing Cr(VI) ions from aqueous solutions. Characterisation of the adsorbents after adsorption suggests that Cr(VI) adsorption can be mainly attributed to ion exchange with SO₄²⁻ groups.     

Fast and efficient adsorption of azure (II) on nanoporous MCM-41 for its removal,preconcentration and determination in biological matrices

The objective of the present study was to investigate the potential of nanoporous MCM-41 silicate for the azure (II) adsorption from the aqueous solutions. The method is based on the adsorption of azure (II) after passing on MCM-41 in a column. The adsorption with respect to contact time, pH, flow rate of sample, eluent kind and volume was investigated to provide more information about the adsorption characteristics of MCM-41. After elution of the adsorbed dye, the concentrations of dye were determined by UV–Vis spectrophotometer. The method showed good linearity for the determination of azure (II) in the range of 1–200 ng mL^?1 with a regression coefficient of 0.9997. The limit of detection was 0.5 ng mL^?1 and the relative standard deviation for 50 ng mL^?1 of azure (II) was 1.26 %. The adsorption properties of the MCM-41 were investigated using batch method. In order to investigate the efficiency of adsorption, pseudo-first-order, pseudo-second-order and intra particle diffusion kinetic models were studied. It was observed that the pseudo-second-order kinetic model fits better than other kinetic models with good correlation coefficient. Equilibrium data were fitted to the Langmuir model. Adsorption equilibrium reach within 5 min of contact time and adsorption capacity was found to be 66.0 mg g^?1. The method was applied to the determination of azure (II) in river water, broth culture medium and DNA samples.     

Removal of methylene blue from aqueous solutions by poly(2-acrylamido-2-methylpropane sulfonic acid-co-itaconic acid) hydrogels

In this study, removal of methylene blue (MB) from aqueous solution by poly(AMPS-co-IA) hydrogels was examined by batch equilibration technique. The effects of monomer ratio, concentration of initiator and crosslinker, pH, adsorption time, initial dye concentration and adsorption temperature on the removal of MB were studied. The results show that the removal of MB was highly effected by preparation conditions of hydrogel. The maximum removal was observed at 10/90 IA/AMPS monomer ratio, 1.0% KPS, and 10.0% MBAAm concentrations. Removal of MB was strongly affected by pH. Pseudo-first-order, pseudo-second-order and intraparticle diffusion models were applied. It was concluded that adsorption of MB on hydrogel followed pseudo-second-order kinetics. It was found that the adsorption isotherm of the MB fit Langmuir-type isotherms. From the Langmuir equation, the adsorption capacity was found as 1,000 mg/g for MB dye. Thermodynamic parameters suggest that the adsorption is a typical physical process, spontaneous, and exothermic in nature. Ten adsorption—desorption cycles demonstrated that the hydrogels were suitable for repeated use without considerable change in adsorption capacity. The results revealed that this hydrogels have potential to be used as an adsorbent for the removal of MB from aqueous solution.     

Adsorption studies on the removal of Malachite Green from aqueous solutions onto halloysite nanotubes

Halloysite nanotubes (HNTs) were used as nano-adsorbents for removal of the cationic dye, Malachite Green (MG), from aqueous solutions. The adsorption of the dye was studied with batch experiments. The natural HNTs used as adsorbent in this work were initially characterized by FT-IR and TEM. The effects of adsorbent dose, initial pH, temperature, initial dye concentration and contact time were investigated. Adsorption increased with increasing adsorbent dose, initial pH, and temperature. Equilibrium was rapidly attained after 30 min of contact time. Pseudofirst-order, pseudo-second-order and intraparticle diffusion models were considered to evaluate the rate parameters. The adsorption followed pseudo-second-order kinetic model with correlation coefficients greater than 0.999. The factors controlling adsorption process were also calculated and discussed. The maximum adsorption capacity of 99.6 mg g⁻¹ of MG was achieved in pH = 9.5. Thermodynamic parameters of ΔG°, ΔH° and ΔS° indicated the adsorption process was spontaneous and endothermic.     

Removal of methylene blue dye from aqueous solution by activated carbon prepared from cashew nut shell as a new low-cost adsorbent

Methylene blue dye was adsorbed on an adsorbent prepared from cashew nut shell. A batch adsorption study was carried out with variable adsorbent amount, initial dye concentration, contact time and pH. Studies showed that the pH of aqueous solutions affected dye removal as a result of removal efficiency increased with increasing solution pH. The experimental data were analyzed by the Langmuir, Freundlich, Redlich-Peterson, Koble-Corrigan, Toth, Temkin, Sips and Dubinin-Radushkevich models of adsorption using MATLAB 7.1. The experimental data yielded excellent fits within the following isotherm order: Redlich-Peterson>Toth>Sips>Koble-Corrigan>Langmuir>Temkin>Dubinin-Radushkevich>Freundlich, based on its correlation coefficient values. Three simplified kinetic models including a pseudofirst-order, pseudo-second-order and intraparticle diffusion equations were selected to follow the adsorption process. It was shown that the adsorption of methylene blue could be described by the pseudo-second-order equation. The results indicate that cashew nut shell activated carbon could be employed as a low cost alternative to commercial activated carbon in the removal of dyes from wastewater.     

Adsorption of different dyes from aqueous solution using Si-MCM-41 having very high surface area

Adsorption characteristics of four different dyes Safranin O (cationic), Neutral Red (neutral), Congo Red (anionic) and Reactive Red 2 (anionic) on Si-MCM-41 material having very high surface area are reported. The surface morphology of Si-MCM-41 material before and after adsorbing dye molecules are characterised by FTIR, HRXRD, nitrogen adsorption–desorption isotherms, FESEM, and HRTEM. The adsorption capacities of Si-MCM-41 for the dyes followed a decreasing order of NR > SF > CR > RR2. The adsorption kinetics, isotherm and thermodynamic parameters are investigated in detail for these dyes using calcined Si-MCM-41. The kinetics and isotherm data showed that both SF and NR adsorb more rapidly than CR and RR2, in accordance with pseudo-second-order kinetics model as well as intraparticle diffusion kinetics model and Langmuir adsorption isotherm model respectively. The thermodynamic data suggest that the dye uptake process is spontaneous. The high adsorption capacities of dyes on Si-MCM-41 (q_m = 275.5 mg g^?1 for SF, q_m = 288.2 mg g^?1 for NR) is explained on the basis of electrostatic interactions as well as H-bonding interactions between adsorbent and adsorbate molecules. Good regeneration capacity is another important aspect of the material that makes it potent for the uptake of dyes from aqueous solution.     

Comparison of Basic Dye Crystal Violet Removal from Aqueous Solution by Low-Cost Biosorbents

Abstract

The removal of basic dye crystal violet by low-cost biosorbents was investigated in this study using a batch experimental system. The adsorption of crystal violet onto various adsorbents was solution pH-dependent and the maximum removal occurred at basic pH 10.0. The kinetic experimental data were analyzed using pseudo-first-order and pseudo-second-order equations to examine the adsorption mechanism and the intraparticle diffusion model to identify the potential rate controlling step. These results suggested that the adsorption of crystal violet onto various adsorbents was best represented by the pseudo-second-order equation. The suitability of the Langmuir and Freundich adsorption isotherms to the equilibrium data was also investigated at various temperatures for all four sorbents and the adsorption isotherms exhibited Freundlich behavior. The Freundlich constant K_f was 1.55 for alligator weed, 2.33 for Laminaria japonica, 9.59 for rice bran and 5.38 (mg/g)/(mg/L)^1/n for wheat bran, respectively at adsorbent concentration 5 g/L, pH 10.0 and 20°C. The thermodynamic parameters (ΔH, ΔG, and ΔS) were calculated and the results showed that the adsorption process for various adsorbents was spontaneous, endothermic, with an increased randomness, respectively. The particle size and the reaction temperature exhibited an insignificant impact on the adsorption equilibrium of crystal violet. The adsorbents investigated could serve as low-cost adsorbents for removing the crystal violet from aqueous solution.     

Equilibria,Kinetics, and Mechanisms for the Adsorption of Four Classes of Phenolic Compounds onto Synthetic Resins

The adsorption of five phenolic compounds of four different classes from aqueous batch solutions onto four styrene-divinylbenzene and acrylic resins (EXA 90, EXA 118, XAD 7, and XAD 16) was investigated regarding their equilibria, kinetics and surface-energy heterogeneity, and mechanisms of adsorption. The experimental equilibrium data were very well fitted to Langmuir and Freundlich models (R ² > 0.900). Three kinetic models (pseudo-first-order, pseudo-second-order, and an intra-particle diffusion model) were suitable for describing the experimental data, the pseudo-second-order kinetic model being the best one (p < 0.001). The adsorption energy values were low (<19.00 kJ/mol), suggesting a physical adsorption process. Driving forces involved in the adsorption of the phenolic compounds onto the resins were hydrogen bonding, π ? π stacking and hydrophobic interactions.     

Sorption of Brilliant Red HE-3B Reactive Dye from Aqueous Solution onto Seashells Waste: Equilibrium and Kinetic Studies

The potential of waste seashells powder, as a new adsorbent for Brilliant Red HE-3B reactive dye removal from aqueous solutions, was examined by the batch technique. The Freundlich, Langmuir, and Dubinin-Radushkevich adsorption models were applied to describe the equilibrium sorption data and to determine the corresponding isotherm constants. The values of the thermodynamic parameters, ΔG, ΔH, and ΔS, indicate that the sorption of reactive dye is a spontaneous and endothermic process. The kinetic data evaluated by pseudo-first order, pseudo-second order, and intraparticle diffusion kinetic models suggested that the sorption of reactive dye onto seashell is a complex process and both surface sorption and intraparticle diffusion contributes to the rate limiting step.     

MODIFIED PLANTAIN PEEL AS CELLULOSE-BASED LOW-COST ADSORBENT FOR THE REMOVAL OF 2,6-DICHLOROPHENOL FROM AQUEOUS SOLUTION: ADSORPTION ISOTHERMS,KINETIC MODELING,AND THERMODYNAMIC STUDIES

In this study, the feasibility of using modified plantain peel to remove 2,6-dichlorophenol from iaqueous solutions was investigated under batch mode. The effects of physical factors such as initial 2,6-dichlorophenol concentration, contact time, biosorbent particle size, biosorbent dosage and temperature on the removal process were evaluated. The results showed that biosorption of 2,6-dichlorophenol was dependent on these factors. The equilibrium biosorption data were analyzed by the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (D-R) adsorption isotherm models. The four tested isotherm models provided good fits to the experimental data obtained at 30°C; however, the Freundlich isotherm model provided the best correlation (R² = 0.9874) of the experimental data. The maximum monolayer biosorption capacity (Q _max ) was found to be 14.25 mg/g. The biosorption kinetics data of 2,6-dichlorophenol were analyzed by pseudo-first-order, pseudo-second-order, Elovich, intraparticle diffusion, and liquid film diffusion models. The five kinetic models fitted well to the biosorption kinetic data; however, the pseudo-second-order kinetic model gave the best fit when the biosorption mechanism was controlled by film diffusion. Thermodynamic quantities such as standard Gibbs free energy (ΔG°), standard enthalpy (ΔH°), standard entropy change of biosorption (ΔS°), and activation energy (E_a) were evaluated, and it was found that the biosorption process was spontaneous, feasible, endothermic in nature and of dual nature, physisorption and chemisorption; however, the physisorption process was dominant. Therefore, modified plantain peel has potential for application as an effective bioadsorbent for removal of 2,6-dichlorophenol from aqueous solution.     

Removal of Anionic Dyes from Water using Citrus limonum (Lemon) Peel: Equilibrium Studies and Kinetic Modeling

Abstract

The present study was undertaken to evaluate the adsorption potential of Citrus limonum (lemon) peel as an adsorbent for the removal of two anionic dyes, Methyl orange (MO) and Congo red (CR) from aqueous solutions. The adsorption was studied as a function of contact time, initial concentration, and temperature by batch method. The adsorption capacities of lemon peel adsorbent for dyes were found 50.3 and 34.5 mg/g for MO and CR, respectively. The equilibrium adsorption data was well described by the Langmuir model. Three simplified kinetic models viz. pseudo-first-order, pseudo-second-order, and Weber and Morris intraparticle diffusion model were tested to describe the adsorption process. Kinetic parameters, rate constants, equilibrium sorption capacities, and related correlation coefficients for each kinetic model were determined. It was found that the present system of dyes adsorption on lemon peel adsorbent could be described more favorably by the pseudo-first-order kinetic model. The results of the present study reveal that lemon peel adsorbent can be fruitfully utilized as an inexpensive adsorbent for dyes removal from effluents.