CO2 adsorption performance of polyethyleneimine-modified ion-exchange resin

A series of solid amine adsorbents were prepared by the template method with ion-exchange resin (D001) as the carrier and polyethyleneimine (PEI) as the modifier. The absorbents were characterized by energy disperse spectroscopy (EDS), scanning electron microscope (SEM), N₂ adsorption–desorption, Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) techniques. The effects of PEI loading, adsorption temperature and influent velocities on CO₂ adsorption capacity in a fixed-bed reactor were investigated. The results show that the solid amine adsorbent prepared by the template method had a better PEI dispersion, stability and CO₂ adsorption capacity. The maximum CO₂ adsorption capacity was 3.98 mmol·g^?1 when PEI loading was 30%, the adsorption temperature was 65°C and the influent velocity was 40 mL·min^?1. The CO₂ adsorption capacity decreased only by 9.50% after 10 cycles of adsorption–desorption tests. The study of kinetics indicates that both chemical adsorption and physical adsorption occurred in the CO₂ adsorption process. The CO₂ adsorption process included fast breakthrough adsorption and gradually approaching equilibrium stage. The particle internal diffusion process was the control step for CO₂ adsorption.     

CO2 capture of amino functionalized three-dimensional worm-hole mesostructured MSU-J silica

Tetraethylenepentamine (TEPA) was employed to functionalize the large-pore mesoporous silica (denoted MSU-J) with 3D worm-hole framework structures which was prepared through a supramolecular hydrogen-bonding assembly pathway from low-cost H₂NCH(CH₃)CH₂[OCH₂CH(CH₃)]₃₃NH₂ (D2000) as structure-directing porogens and tetraethylorthosilioate as the silica source for capturing CO₂. The resultant adsorbents were characterized by FT-IR, Transmission electron microscopy (TEM), N₂ adsorption/desorption and thermogravimetric analysis. Textural properties, elemental analysis and TEM measurement of the samples showed a severe pore filling of MSU-J as TEPA loading was increased to 70 wt%. CO₂ adsorption isotherms measured at different temperatures revealed the optimal adsorption temperature is 25 °C. The adsorption capacity of MSU-J with different TEPA loading contents was calculated. As a result, 50 wt% of TEPA supported on as-synthesized MSU-J achieved the highest capacity with the value of 164.3 mg/g under the conditions of 99.99 % CO₂ at 25 °C and 0.1 MPa. Repeated adsorption/desorption cycles revealed that amine-impregnated materials was very efficient for less apparent decrease in CO₂ adsorption capacity even after 6 adsorption–regeneration cycles.     

Preparation of amine-modified SiO<Subscript>2</Subscript> aerogel from rice husk ash for CO<Subscript>2</Subscript> adsorption

Amine-modified SiO₂ aerogel was prepared using 3-(aminopropyl)triethoxysilane (APTES) as the modification agent and rice husk ash as silicon source, its CO₂ adsorption performance was investigated. The amine-modified SiO₂ aerogel remains porous, the specific surface area is 654.24 m²/g, the pore volume is 2.72 cm³/g and the pore diameter is 12.38 nm. The amine-modified aerogel, whose N content is up to 3.02 mmol/g, can stay stable below the temperature of 300 °C. In the static adsorption experiment, amine-modified SiO₂ aerogel (AMSA) showed the highest CO₂ adsorption capacity of 52.40 cm³/g. A simulation was promoted to distinguish the adsorption between the physical process and chemical process. It is observed that the chemical adsorption mainly occurs at the beginning, while the physical adsorption affects the entire adsorption process. Meanwhile, AMSA also exhibits excellent CO₂ adsorption–desorption performance. The CO₂ adsorption capacity dropped less than 10 % after ten times of adsorption–desorption cycles. As a result, AMSA with rice husk ash as raw material is a promising CO₂ sorbent with high adsorption capacity and stable recycle performance and will have a broad application prospect for exhaust emission in higher temperature.     

Synthesis and characterization of monolithic carbon/silicon carbide composite aerogels

Resorcinol–formaldehyde/silica composite (RF/SiO₂) aerogels were synthesized using sol–gel process followed by supercritical CO₂ drying. Monolithic carbon/silicon carbide composite (C/SiC) aerogels were formed from RF/SiO₂ aerogels after carbothermal reduction. X-ray diffraction and transmission electron microscopy demonstrate that β-SiC was obtained after carbothermal reduction. Scanning electron microscopy and nitrogen adsorption/desorption reveal that the as-prepared C/SiC aerogels are typical mesoporous materials. The pore structural properties were measured by nitrogen adsorption/desorption analysis. The resulting C/SiC aerogels possess a BET surface area of 564 m²/g, a porosity of 95.1 % and a pore volume of 2.59 cm³/g. The mass fraction of SiC in C/SiC aerogels is 31 %.     

拟薄水铝石负载PEI/AMP吸附CO2性能

用富含胺基的物质对多孔材料进行修饰可以得到高CO₂吸附量的吸附剂。采用浸渍法将聚乙烯亚胺(PEI)和2-氨基-2-甲基-1-丙醇(AMP)负载在拟薄水铝石上,考察了CO₂压力、胺类物质负载量等对吸附性能的影响。采用低温N₂吸附/脱附法(BET)、扫描电镜(SEM)、傅里叶变换红外线光谱分析仪(FTIR)等手段表征了吸附剂的结构特征及其物理性质,并使用重量法微天平实验装置对吸附剂的性能进行了评价。实验结果表明,当温度恒定为50℃,压力小于1 MPa时,负载PEI的吸附剂最高的CO₂吸附量为77.53 mg CO₂·(g吸附剂)^-1,最佳负载量为85%;压力大于1 MPa时,负载PEI的吸附剂最高的CO₂吸附量为123.79 mg CO₂·(g吸附剂)^-1,最佳负载量为10%。负载AMP的吸附剂最高的CO₂吸附量为128.01 mg CO₂·(g吸附剂)^-1,最佳负载量为85%。CO₂吸附稳定性实验表明,吸附剂对CO₂的吸附性能稳定。     

Synthesis and application of nanocomposite Fe3O4@SiO2@CTAB–SiO2 as a novel adsorbent for removal of cyclophosphamide from water samples

ABSTRACT

We present a way of synthesizing nanocomposite Fe₃O₄@SiO₂@CTAB–SiO₂ by employing simple sol–gel technique with selective etching for extreme selectivity adsorption of cyclophosphamide (CP). The transmission electron microscopy (TEM); scanning electron microscopy (SEM); X-ray diffraction (XRD); Fourier transform infrared (FT-IR); vibrating sample magnetometer (VSM); pH_PZC; and Brunauer, Emmett and Teller (BET) techniques were used for nanocomposite characterization. These nanoparticles have an S_BET of 157.8 m² g^?1 and a high saturation magnetization of 67.5 emu g^?1. First, the adsorption system was examined as a function of contact time under various initial CP contents, ionic strength, initial solution pH, adsorbent dose and temperature in batch test. The optimum dose, pH and contact time were obtained to be 0.01 g, 7.0 and 30 min, respectively. Ultimately, experimental isotherm and kinetics data of adsorption of CP onto nanocomposite Fe₃O₄@SiO₂@CTAB–SiO₂ were fitted to classical models. Additionally, it was found that the maximum adsorption process capacity of CP on adsorbent was 342.8 mg g^?1.     

CO2 Adsorption by Modified Palm Shell Activated Carbon (PSAC) Via Chemical and Physical Activation and Metal Impregnation

The aim of this study was to verify the ability of nickel-impregnated palm shell activated carbon (PSAC) for CO₂ adsorption and compare its performance with the chemically and physically activated PSAC. Sodium hydroxide and CO₂ were used as activating agents for chemical and physical activation, respectively. Nickel nitrate hexahydrate (Ni(NO₃)₂·6H₂O) was used as a precursor for metal impregnation. The effect of different chemical loadings (NaOH: 20–50 wt%), metal impregnation (Ni(NO₃)₂·6H₂O: 16–28 wt%), and heat treatment time (1–4 h) was studied as parameters. Adsorption capacity was calculated using breakthrough graphs. The effect of humidity on CO₂ adsorption and desorption of CO₂ was also investigated in this study. The results revealed that chemically modified PSAC yields the highest adsorption capacity (48.2 mg/g) compared to other methods of activation. Interestingly, it was found that the adsorption capacity of nickel-impregnated PSAC was similar to other types of metal-impregnated activated carbon. Humidity gave a negative effect on CO₂ adsorption. In summary, results showed that chemical activation is an efficient technique to modify PSAC for CO₂ adsorption.     

Synthesis of High Surface Area MgAl2O4 Nanopowder as Adsorbent for Leather Dye Removal

Abstract

MgAl₂O₄ nanopowder has been prepared by alkoxides hydrolysis with further calcination at temperature of 700°C. The adsorption of a leather dye, Direct Black 38, onto this material was investigated. The sample was characterized by X-ray-diffraction (XRD), N₂ adsorption–desorption isotherm and Fourier transform infrared spectroscopy. The results showed that sample present a pure phase, and the average nanocrystal size of 8 nm, the BET surface area is about 206.5 m² · g^?1 and total pore volume is about 1.44 cm³ · g^?1. Adsorption kinetics data were modeled by film and pore diffusion model. The experimental isotherm was described by the Langmuir model. MgAl₂O₄ nanopowder presented a great removal efficiency of leather dye by adsorption process, with a maximum adsorption capacity of 833 mg of dye per gram of adsorbent.     

Synthesis,characterization, and evaluation of unsupported porous NiS submicrometer spheres as a cathode material for lithium batteries

Synthesis of a nanostructured pure phase nickel sulfide in a single step is a challenge. In this work, a new method for direct synthesis of uniform NiS–SiO₂ submicrospheres was developed by ultrasonic spray pyrolysis. Colloidal silica was used as a sacrificial template to create the porous structure. After silica removal, hollow, porous pure phase NiS nanospheres were obtained. The product was characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, transmission electron microscopy, and N₂ adsorption/desorption isotherm. The results confirmed the formation of single phase millerite NiS porous nanospheres with a high surface area of 312 m² g^?1. The NiS spheres were tested as cathode for lithium batteries. A discharge capacity of 340 mAh g^?1 with good capacity retention during multiple cycles was obtained.     

Effects of different structure-directing agents (SDA) in MCM-41 on the adsorption of CO2

CO₂ capturing technologies have attracted significant attention in order to limit emissions and reduce their negative effect on the environment. Mesoporous silica materials (MCM-41) are easily recyclable, affordable, and thermally and mechanically stable, providing added benefits in CO₂ capture. However, further studies are necessary to characterize the effects of MCM-41 pore size, adsorption temperature and surface silylation on CO₂ adsorption efficiency. In this work, mesoporous silica is synthesized using alkyltrimethylammonium bromide with different chain lengths (C_nH_2n + 1 N(CH₃)₃Br, n = 14, 16 and 18) as structure-directing agents, and the adsorption capacity of CO₂ on TTMCM-41 (C₁₇H₃₈NBr), CTMCM-41 (C₁₉H₄₂NBr), DTMCM-41(C₂₁H₄₆NBr) samples was measured gravimetrically at room temperature and pressure up to 40 bar. The silica structures were characterized by X-ray diffraction (XRD), nitrogen adsorption/desorption, Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy and transmission electron microscopy (TEM). The XRD, N₂ adsorption–desorption and TEM measurements indicated the presence of a well-ordered hexagonal array with uniform mesostructures. The mesoporous silica obtained, denoted as TTMCM-41, CTMCM-41 and DTMCM-41, had distinct physical properties, such as BET surface area, hexagonal unit cell, pore volume, pore diameter and pore wall thickness. CTMCM-41 exhibited an adsorption capacity (0.58 g CO₂/g adsorbent) of more than DTMCM-41 (0.48 g CO₂/g adsorbent) and TTMCM-41 (0.42 g CO₂/g adsorbent). The results suggest that CTMCM-41 can be a better mesoporous adsorbent for CO₂ adsorption .     

Highly Stable Amine-modified Mesoporous Silica Materials for Efficient CO2 Capture

A highly efficient and stable solid adsorbent invoking a direct incorporation of tetraethylenepentamine (TEPA) onto the as-synthesized mesocelullar silica foam (MSF) has been developed for CO₂ capture. Unlike most amine-functionalized silicas, which typically exhibit CO₂ adsorption capacities less than 2.0 mmol/g, such organic template occluded mesoporous silica-amine composites exhibited remarkably high CO₂ uptake as high as 4.5 mmol/g at 348 K and 1 atm. Moreover, notable increases in CO₂ adsorption capacities of the composite materials were observed when in the presence of humidity. Durability test performed by cyclic adsorption–desorption revealed that such adsorbents also possess excellent stability, even though a slight decrease in adsorption capacity over time was observed.     

Influence of regeneration conditions on the cyclic performance of amine-grafted mesoporous silica for CO2 capture: An experimental and statistical study

This work deals with the behavior of amine-grafted mesoporous silica (referred to as TRI-PE-MCM-41) throughout adsorption–desorption cycles in the presence of 5% CO₂/N₂ using various regeneration conditions in batch experiments. The criteria proposed to determine the optimum regeneration conditions are the working adsorption capacity, the rate of desorption and the change of adsorption capacity between consecutive cycles. Using a 2³ factorial design of experiments, the impact on the performance of the adsorbent of different levels of temperature, pressure, and flow rate of purge gas during desorption was determined. It was found that all the parameters under study have a statistically significant influence on the working adsorption capacity, but only temperature is influential with respect to desorption rate. Regeneration using temperature swing was found to be attractive, as the highest CO₂ adsorption capacity (1.95 mmol g^?1) and the fastest desorption rate (9.82×10^?4 mmol g^?1 s^?1) occurred when desorption was carried out at 150 °C. However, if vacuum is applied, regeneration can be achieved at a temperature as low as 70 °C with only a 13% penalty in terms of working adsorption capacity. It was also demonstrated that under the proper regeneration conditions, TRI-PE-MCM-41 is stable over 100 adsorption–desorption cycles.     

CO<Subscript>2</Subscript> adsorption at high pressures in MCM-41 and derived alkali-containing samples: the role of the textural properties and chemical affinity

The adsorption properties of N₂ and CO₂ of MCM-41 and derived alkali-containing samples were analyzed over a wide range of pressures (up to ~4500 kPa) and temperatures (between 30 and 300 °C). The high-pressure and high-temperature experiments were carried out on pure MCM-41 and K- and Na-impregnated derived samples. It was analyzed the influence of pressure and temperature on the CO₂ capture capacity on pure and impregnated samples. The adsorption performance was correlated to the structure and textural properties of the materials using X-ray diffraction and N₂ adsorption–desorption measurements. The addition of an alkaline element changes the textural properties of the material increasing the pore size, which positively affected the CO₂ adsorption capacity of these materials at high pressure. In addition, the isosteric heats of adsorption gave information about the chemical affinity between the impregnated materials and CO₂. The CO₂ adsorption at ~ 4500 kPa for the samples with 5 wt% Na at 100 and 200 °C were 77.98 and 9.79 mmol g^?1, respectively, while the pure MCM-41 adsorbs only 8.92 mmol g^?1.     

Greenhouse Gas Adsorptivity of Horn-Shaped Carbon Nanotubes over Nitrogen: Equilibrium Study

The synthesis of horn-shaped carbon nanotubes using carbon tetrachloride as carbon source was carried out by solvothermal method at 200°C for 2 h. The scanning and transmission electron microscopic characterization of the obtained product showed the formation of horn-shaped carbon nanotubes with irregular wall structure having inner diameter of ～105 nm and length of ～1 µm. The equilibrium gas adsorption properties of horn-shaped carbon nanotubes derived from carbon tetrachloride were successfully investigated for CO₂, CH₄, and N₂ at 288, 303, and 318 K. Horn-shaped carbon nanotubes possess better CO₂ adsorption capacity (2.53 mmol/g) with high capacity selectivity (14.7) and equilibrium selectivity (59.1) over N₂ at 288 K. The detailed adsorption study with estimation of physical parameters such as Henry's constant and heat of adsorption identifies the horn-shaped carbon nanotubes as a potential adsorbent material in the field of CO₂ storage and separation.     

Adsorption of CO<Subscript>2</Subscript> by iron-exchanged heteropolyacid Fe<Subscript>1.5</Subscript>PMo<Subscript>12</Subscript>O<Subscript>40</Subscript> supported on mesoporous cellular foams

Novel low-temperature swing adsorbents that preferably adsorb CO₂ were synthesized by varying loading of heteropolyacid Fe_1.5PMo₁₂O₄₀ (Fe–PMA) supporting on mesoporous cellular foams (MCFs) by wetting impregnation. The synthesized materials were characterized by various physicochemical, thermal and spectral techniques and the CO₂ adsorption capacity of the materials were evaluated. Solid adsorbents showed a significantly high adsorption capacity toward CO₂ due to the chemisorptions of CO₂. The CO₂ adsorption capacities of the materials decreased as the temperature increased. The results showed that the adsorption capacity reached a level of 81.8 mg CO₂/g-adsorbent at 25 °C for the 20 wt% Fe–PMA–MCFs. These results indicated that the iron (Fe²⁺) complexes acted as efficient catalysts for the separation of CO₂. The as-synthesized adsorbents were selective, thermally stable, long-lived, and could be recycled at a temperature of 110 °C.     

K‐Promoted Hydrotalcites for CO2 Capture in Sorption Enhanced Reactions

Potassium‐promoted hydrotalcite‐like material was prepared with potassium nitrate as the K precursor. The highest ever reported CO₂ adsorption capacity (1.13 mol kg^–1) was obtained at 656 K with p = 0.5 bar at humid conditions. A mathematical model was developed and it satisfactorily simulated the adsorption and desorption processes. The stability of the material was tested with repeated adsorption/desorption cycles; the CO₂ adsorption capacity decreased around 7 % after ten cycles. In addition, regeneration was performed with temperature swing operation (from 656 K to 708 K), where a complete regeneration was achieved within 60 min, which reduced to half the time required for regeneration under isothermal conditions.     

Comparative CO2 Adsorption Analysis in Pure and Amine-Modified Composite Membranes

In this study, the CO₂ adsorption analysis in cellulose acetate–TiO₂- and cellulose acetate–3-aminopropyl-trimethoxysilane TiO₂-blended membranes was performed. The membranes were also characterized using scanning electron microscopy and Fourier transform infrared analysis techniques. The adsorption results indicated that 120 and 90°C were considered as optimized temperatures for regeneration of cellulose acetate–TiO₂ and cellulose acetate–3-aminopropyl-trimethoxysilane-modified TiO₂ membranes. The testing results revealed that adsorption capacity reached maximum at 3.0 bars. Validation of experimental results was performed by pseudo-first-order, second-order and intraparticle diffusion models. The correlation factor R² represented that the second-order model was fitted well with the experimental data. The intraparticle diffusion model represented that adsorption is not a single-step process.     

Fabrication of PEI-grafted porous polymer foam for CO2 capture

A polymer foam material with both the open-cell porous structure and the polyethylenemine (PEI)-grafted inner face was constructed for CO₂ capture. The porous poly(tert-butyl acrylate) foam was first prepared via a concentrated emulsion polymerization, and then the carboxyl groups were introduced on the interface of porous polymer after the hydrolysis reaction. Subsequently, the surface of the foam was grafted with PEI, and finally the PEI-grafted porous polymer foam designed as a CO₂ capture material was obtained. The structures of the foams were characterized by infrared spectroscopy, EDS, and SEM. The CO₂ adsorption properties were measured by adsorption/desorption cycles. As a result, the polymer foam contained a large number of amine groups (13.9 wt % N), and therefore possessed a high CO₂ adsorption capacity (5.91 mmol g⁻¹ at 40°C and 100 kPa). In addition, they also exhibited high CO₂ adsorption rate, good selectivity for CO₂-N₂ separation, and good stability according to CO₂ cyclic adsorption/desorption test. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47844.     

Aminating modification of viscose fibers and their CO2 adsorption properties

An adsorbent for CO₂ capture was prepared by the grafting of acrylonitrile (AN) onto viscose fibers (VFs); this was followed by amination with triethylene tetramine (TETA). The effects of the reaction conditions, such as the concentrations of the monomer, initiator, and nitric acid, on the grafting degree and grafting efficiency were studied. The adsorption performance of the adsorbent for CO₂ was evaluated by fixed‐bed adsorption. The highest dynamic adsorption capacity of the adsorbent for CO₂ was 4.35 mmol/g when the amine content of the adsorbent VF–AN–TETA reached 13.21 mmol/g. Compared with the polypropylene (PP)‐fiber‐based adsorbent (PP–AN–TETA), VF–AN–TETA with hydroxyl groups on the fibers facilitated the diffusion of CO₂ and water and led to a higher CO₂ adsorption capacity than that of PP–AN–TETA. The VF–AN–TETA adsorbent also showed good regeneration performance: its CO₂ adsorption capacity could still retain almost the same capacity as the fresh adsorbent after 10 adsorption–desorption cycles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42840.     

Application of attapulgite/maltose system on mesoporous carbon material preparation for electrochemical capacitors

Mesoporous carbon materials were prepared through atmospheric pressure impregnation at room temperature using attapulgite as hard template and maltose as carbon source. N₂ absorption–desorption, X-ray diffraction, and transmission electron microscopy were used to determine the construction and morphology of the materials. The results showed that the prepared carbon materials possessed chain-layered structures whose surfaces were filled with ample nanoscale apertures. The materials also exhibited partial fasciculus with specific surface area and total pore volume of 628.6 m² g^?1 and 1.31 cm³ g^?1, respectively. Constant current charge/discharge, cyclic voltammetry, and AC impedance tests were performed to evaluate the electrochemical performance of the materials. The constant current charge/discharge tests showed that the materials have excellent energy storage capacity. When the current density was 600 mA g^?1, the specific capacitance value reached 171 F g^?1. The materials showed quasi-rectangular features of typical cyclic voltammetry curve even at high scan rate (200 mV s^?1), indicating that they possess excellent rate capacity. The AC impedance tests showed that the materials were typical porous electrode materials with combination resistance of 0.82 Ω. The specific capacitance of the materials reached 79 % after 1,000 constant current charge/discharge cycles, indicating that they have superior cyclic stability.