Simultaneous Absorption of Carbon Dioxide and Sulfur Dioxide into Aqueous 2-Amino-2-Methy-1-Propanol

Abstract

Carbon dioxide and sulfur dioxide were simultaneously absorbed into aqueous 2-amino-2-methyl-1-propanol (AMP) in a stirred semi-batch tank with a planar gas-liquid interface within a range of 0–4.0 kmol/m³ of AMP, 0.03–0.3 mole fraction of CO₂, 0.005–2 mole fraction of SO₂, and 298–318 K. Absorption data of each gas in the CO₂-AMP and SO₂-AMP systems are obtained to verify their reaction regimes, based on film theory, respectively, which are used to analyze the simultaneous absorption mechanisms of CO₂ and SO₂ in the CO₂-SO₂-AMP systems. The measured absorption rates of CO₂ and SO₂ are compared to those formulated by an approximate solution of the mass balances with simultaneous reactions.     

Simultaneous Absorption of Carbon Dioxide and Nitrogen Dioxide into Aqueous 2-amino-2-methy-1-propanol

Carbon dioxide and nitrogen dioxide were simultaneously absorbed into aqueous 2-amino-2-methyl-1-propanol (AMP) in a stirred semi-batch tank with a planar gas-liquid interface within a range of 0–4.0 kmol/m³ of AMP, 0.03–0.3 atm of CO₂, 0.005–0.2 atm of NO₂, and 298–318 K. Absorption data of each gas in the CO₂-AMP and NO₂-AMP systems were obtained to verify their reaction regimes, based on film theory, respectively, which were then used to analyze the simultaneous absorption mechanisms of CO₂ and NO₂ in the CO₂-NO₂-AMP systems. The measured absorption rates of CO₂ and NO₂ were compared to those formulated by an approximate solution of the mass balances with simultaneous reactions.     

Absorption of Carbon Dioxide into Aqueous Solution of Sodium Glycinate

Abstract

Carbon dioxide was absorbed into aqueous solution of sodium glycinate (SG) at different SG concentrations, CO₂ partial pressures, and temperatures in the range of 0.5–3.0 kmol/m³, 25–101.3 kPa, and 298–318 K, respectively, using a stirred semi-batch vessel with a planar gas-liquid interface. Both the reaction order and rate constant are determined from gas absorption rates under the fast reaction regime. The reaction was found to be first order with respect to both CO₂ and SG. The activation energy for the CO₂-SG reaction has been found to be 59.8 kJ/mol. The second-order reaction rate constants were used to obtain the theoretical values of absorption rate based on the film theory.     

Chemical Absorption of Carbon Dioxide into Aqueous Solution of Potassium Threonate

Carbon dioxide was absorbed into aqueous solution of potassium threonate (PT) at different concentrations of PT and CO₂, and temperatures in the range of 0.1–1.0 kmol/m³, 10.1–101.3 kPa, and 293-313 K, respectively, using a stirred semi-batch vessel with a planar gas-liquid interface. Both the reaction order and rate constant were determined from gas absorption rates under the fast pseudo-first-reaction regime. The reaction was found to be first order with respect to both CO₂ and PT, and its activation energy has been found to be 40.6 kJ/mol. From a comparison of the reaction kinetics by the overall reaction scheme with those by the elementary reaction scheme based on the zwitterions mechanism, the overall reaction between CO₂ and PT has been found to be equivalent to the formation of zwitterions.     

Absorption of Carbon Dioxide into Ionic Liquid of 2-Hydroxy Ethylammonium Lactate

Abstract

Absorption of carbon dioxide into organic solvents such as DMA, NMP, DMSO, and DMF with the 2-hydroxy ethylammonium lactate (HEAL) ionic liquid was investigated using a batch stirred tank with a plane of gas-liquid interface in a range of 0–2.0 kmol/m³ of HEAL and 298–318 K at 101.3 kPa. The absorption of CO₂ was analyzed with the film model accompanied by the zwitterion mechanism of CO₂ with HEAL. The proposed model fits the experimental data of the enhancement factor due to the ready, chemical absorption of CO₂ in different solvents, temperatures, and HEAL concentrations. The reaction rate constant of CO₂ with HEAL was correlated linearly with the solubility parameter of the solvent.     

Simultaneous absorption of carbon dioxide,sulfur dioxide,and nitrogen dioxide into aqueous 1, 8-diamino-p-menthane

3 gaseous mixtures of CO₂, SO₂, and NO₂ were simultaneously absorbed into 1, 8-diamino-p-menthane (DAM) in a stirred, semi-batch tank with a planar, gas-liquid interface within a range of 0–2.0 kmol/m³ of DAM, 0.05–0.3 atm of CO₂, 0.0025–0.04 atm of SO₂, and 298.15–323.15 K at a fixed NO₂ of 0.001 atm to measure their total molar fluxes. Diffusivity and Henry constants of CO₂, SO₂, and NO₂ were obtained using the reference data, measured by N₂O analogy. The mass transfer coefficient of each gas, needed to obtain the absorption rate without a chemical reaction, was modified with viscosity of aqueous DAM solution. In CO₂-SO₂-NO₂-DAM system accompanied by first-order reaction with respect to CO₂ and instantaneous reactions with respect to SO₂ and NO₂, the enhancement factors of CO₂ and SO₂ were obtained by using an approximate solution of mass balances consisting of reaction regimes of two gases, one of which reacts instantaneously, and then, the enhancement factor of NO₂ by comparing the instantaneous rates of SO₂ and NO₂. The observed values of the molar flux approached to the calculated values very well.     

Absorption of Carbon Dioxide into Aqueous Xanthan Gum Solution Containing Monoethanolamine

Abstract

Carbon dioxide was absorbed into the aqueous xanthan gum (XG) solution in the range of 0–0.151 wt% containing monoethanolamine (MEA) of 0–2 kmol/m³ in a flat‐stirred vessel with the impeller of 0.05 m and agitation speed of 50 rpm at 25°C and 0.101 MPa to measure the absorption rate of CO₂. The volumetric liquid‐side mass transfer coefficient (k_La_L) of CO₂ decreased with increasing XG concentration, and was correlated with the empirical formula having the rheological behavior of XG solution. The chemical absorption rate of CO₂ was estimated by the film theory using the values of k_La_L and physicochemical properties of CO₂ and MEA. The aqueous XG solutions made the rate of absorption of CO₂ accelerated compared with the Newtonian liquid based on the same viscosity of the solution.     

Chemical Absorption of Carbon Dioxide into Aqueous Colloidal Silica Solution with Diethanolamine

Abstract

The chemical absorption rate (R_A) of CO₂ was measured into the aqueous nanometer sized colloidal silica solution of 0–31 wt% and diethanoleamine of 0–2 kmol/m³ in the flat‐stirred vessel with the impeller size of 0.034 m and its agitation speed of 50 rev/min at 25°C and 0.101 MPa, and compared with the values estimated from the model based on the film theory accompanied by chemical reaction. The value of the volumetric liquid‐side mass transfer coefficient (k_La) of CO₂, which was used to estimate the value of R_A, was obtained by the empirical correlation formula presenting the relationship between k_La and the rheological behavior of the aqueous colloidal silica solution. The value of R_A in the aqueous colloidal silica solution was decreased by the reduction of k_La due to the elasticity of the solution.     

Sorption of Carbon Dioxide onto Sodium Carbonate

Abstract

Sodium carbonate was used as a sorbent to capture CO₂ from a gaseous stream of carbon dioxide, nitrogen, and moisture. The breakthrough data of CO₂ were measured in a fixed bed to observe the reaction kinetics of CO₂‐carbonate reaction. Several models such as the shrinking‐core model, the homogeneous model, and the deactivation model in the non‐catalytic heterogeneous reaction systems were used to explain the kinetics of reaction among CO₂, Na₂CO₃, and moisture using analysis of the experimental breakthrough data. Good agreement of the deactivation model was obtained with the experimental breakthrough data. The sorption rate constant and the deactivation rate constant were evaluated by analysis of the experimental breakthrough data using a nonlinear least squares technique and described as Arrhenius form.     

Chemical Absorption of Carbon Dioxide into Aqueous PEO Solution of Monoethanolamine

Abstract

Carbon dioxide was absorbed into aqueous polyethylene oxide (PEO) solution containing monoethanolamine (MEA) in a flat‐stirred vessel to investigate the effect of non‐Newtonian rheological behavior of PEO on the rate of chemical absorption of CO₂, where the reaction between CO₂ and MEA was assumed to be a first‐order reaction with respect to the molar concentration of CO₂ and MEA, respectively. The liquid‐side mass transfer coefficient (k_L), which was obtained from the dimensionless empirical equation containing the properties of viscoelasticity of the non‐Newtonian liquid, was used to estimate the enhancement factor due to chemical reaction. PEO with elastic property of non‐Newtonian liquid made the rate of chemical absorption of CO₂ accelerate compared with Newtonian liquid based on the same viscosity of the solution.     

Thermodynamic Equilibrium Analysis of Propane Dehydrogenation with Carbon Dioxide and Side Reactions

A thermodynamic analysis of propane dehydrogenation with carbon dioxide was performed using constrained Gibbs free energy minimization method. Different reaction networks corresponding to different catalytic systems, including non-redox and redox oxide catalysts, were simulated. The influences of CO₂/C₃H₈ molar ratio (1–10), temperature (700–1000 K), and pressure (0.5–5 bar) on equilibrium conversion and product composition were studied. In the presence of CO₂ with a molar ratio of CO₂/C₃H₈ = 1, the temperature of dehydrogenation can be 30 K lower than that of dehydrogenation in the presence of steam (H₂O/C₃H₈ = 1) and about 50 K lower than that of simple dehydrogenation without dilution to achieve 60% propane conversion. It was found that the occurrence of dry reforming of propane and coke-forming side reactions could strongly impact the equilibrium product composition of the multireaction system and, therefore, these reactions should be kinetically controlled. Comparison of the simulated reactant conversions with those reported in the literatures revealed that the experimental conversion levels of propane are far below the corresponding equilibrium values due to rapid catalyst deactivation by coke, implying that research efforts should be directed toward formulation of more active and selective catalysts.     

Supercritical Carbon Dioxide Fractionation of Anhydrous Milk Fat

Supercritical carbon dioxide was used to fractionate anhydrous milk fat. Six fractions were produced at 40, 50 and 60 °C using pressure values of 10, 20, 25, 30, 33 and 36 MPa. The fractions were analyzed for fatty acids, thermal behavior, iodine and color values. Composition and yield of fatty acid methyl esters were evaluated at different fractionation conditions in relation to the original milk fat values. Short chain fatty acids (C₄–C₈), medium chain fatty acids (C₁₀–C₁₄) and total saturated fatty acids were decreased from fraction obtained in the order of 10–36 MPa, while long chain fatty acids (C₁₆–C_18:2) and total unsaturated fatty acids were increased. Fractions obtained in the raffinate stage of the fractionation exhibited higher melting behavior that obtained at the low CO₂ pressures. The higher iodine value of raffinate fraction indicated that fraction was richer in oleic acid. Fractions produced at low pressures had lower melting behavior than those obtained at high pressures. Yellowness Index and b* values increased in raffinate fraction due to concentration of carotenoids.     

The absorption rate of CO2/SO2/NO2 into a blended aqueous AMP/ammonia solution

The Inter-governmental Panel on Climate Change (IPCC) reported that human activities result in the production of greenhouse gases (CO₂, CH₄, N₂O and CFCs), which significantly contribute to global warming, one of the most serious environmental problems. Under these circumstances, most nations have shown a willingness to suffer economic burdens by signing the Kyoto Protocol, which took effect from February 2005. Therefore, an innovative technology for the simultaneously removal carbon dioxide (CO₂) and nitrogen dioxide (NO₂), which are discharged in great quantities from fossil fuel-fired power plants and incineration facilities, must be developed to reduce these economical burdens. In this study, a blend of AMP and NH₃ was used to achieve high absorption rates for CO₂, as suggested in several publications. The absorption rates of CO₂, SO₂ and NO₂ into aqueous AMP and blended AMP+NH₃ solutions were measured using a stirred-cell reactor at 293, 303 and 313 K. The reaction rate constants were determined from the measured absorption rates. The effect of adding NH₃ to enhance the absorption characteristics of AMP was also studied. The performance of the reactions was evaluated under various operating conditions. From the results, the reactions with SO₂ and NO₂ into aqueous AMP and AMP+NH₃ solutions were classified as instantaneous reactions. The absorption rates increased with increasing reaction temperature and NH₃ concentration. The reaction rates of 1, 3 and 5 wt% NH₃ blended with 30 wt% AMP solution with respect to CO₂/SO₂/NO₂ at 313 K were 6.05～8.49×10^?6, 7.16–10.41×10^?6 and 8.02～12.0×10^?6 kmol m^?2s^?1, respectively. These values were approximately 32.3–38.7% higher than with aqueous AMP solution alone. The rate of the simultaneous absorption of CO₂/SO₂/NO₂ into aqueous AMP+NH₃ solution was 3.83–4.87×10^?6 kmol m^?2s^?1 at 15 kPa, which was an increase of 15.0–16.9% compared to 30 wt% AMP solution alone. This may have been caused by the NH₃ solution acting as an alternative for CO₂/SO₂/NO₂ controls from flue gas due to its high absorption capacity and fast absorption rate.     

Adsorption and Desorption of Carbon Dioxide and Nitrogen on Zeolite 5A

The adsorption equilibrium data of CO₂ and N₂ at (303, 333, 363, 393, 423) K ranging 0-1 bar on zeolite 5A is reported. The pressure and temperature range covers the operating pressure in adsorption units for CO₂ capture from power plants. Experimental data were fitted by the multi-site Langmuir model. The adsorbent is much more selective to CO₂: loading at 303 K and 100 kPa is 3.38 mol/kg while loading of N₂ at the same pressure is 0.22 mol/kg. The Clausius-Clapeyron equation was employed to calculate the isosteric enthalpy of adsorption. The fixed-bed adsorption and desorption of carbon dioxide and nitrogen on zeolite 5A pellets has been studied. A model based on the bi-LDF approximation for the mass transfer, taking into account the energy and momentum balances, had been used to describe the adsorption kinetics of carbon dioxide and nitrogen. The model predicted satisfactorily the breakthrough curves obtained with carbon dioxide–nitrogen mixtures. Desorption process (consisting of depressurization, blowdown, and purge) was also performed. Following the feasibility of concentration and capture of carbon dioxide from flue gases by Pressure Swing Adsorption (PSA) process was simulated. A CO₂ recovery of 91.0% with 53.9% purity was obtained using a five-step Skarstrom-type PSA cycle.     

Investigation on kinetics of carbon dioxide absorption in aqueous solutions of monoethanolamine + 1, 3-diaminopropane

ABSTRACT

Environmental concerns from global warming and climate change demand carbon dioxide separation from post-combustion gases. Important parameters are involved in choosing the suitable solvent for carbon dioxide separation, including the reaction rate of carbon dioxide and the solvent. In this paper, the kinetics of carbon dioxide (CO₂) absorption in aqueous solutions of Monoethanolamine (MEA) + 1,3-Diaminopropane (DAP), a diamine containing two primary amino group, was developed. The measurements were performed in a stirred cell with a horizontal gas-liquid interface in the temperature range of 313.15–333.15 K and aqueous solutions of 10 wt% MEA + 5 wt% DAP and 12.5 wt% MEA + 2.5 wt% DAP. Experiments were conducted in an isothermal batch reactor with a horizontal gas-liquid interface under pseudo-first-order conditions, enabling the determination of the overall kinetic rate constant from the pressure drop method. Second-order reaction rate constants of CO₂ absorption in amine solutions were estimated using the calculated initial absorption rate. It was found that the rate constants in MEA+ DAP solutions were greater than in MEA solutions which means that DAP increases the reaction rate.     

Performance of a UV‐assisted Hydrogen‐peroxide‐fed Spray Tower for Sulfur Dioxide Abatement

Spray towers are widely used for controlling air pollution by gases such as SO₂, CO₂, NO_x, and HCl. Results of sulfur dioxide absorption in a spray tower using solutions of 1 g L^–1 and 2 g L^–1 of hydrogen peroxide are reported. For comparison, a water and sodium hydroxide solution was also used for SO₂ abatement. The results indicate that H₂O₂ may be an important alternative for SO₂ removal in spray towers. A set of experimental removal efficiency data was obtained as a function of gas and liquid flow rates. Volumetric mass transfer coefficients (k_ga) were calculated and an experimental relationship among k_ga, gas, and liquid flow rates was proposed. As a final experiment, an oxidation process assisted by UV radiation using a 1 g L^–1 solution of H₂O₂ was carried out to speed up the SO₂ removal rate. The results obtained in this condition are similar to those achieved with a solution of 2 g L^–1 H₂O₂.     

Isotope Effects in Methanol Synthesis and the Reactivity of Copper Formates on a Cu/SiO2 Catalyst

Here we investigate isotope effects on the catalytic methanol synthesis reaction and the reactivity of copper-bound formate species in CO₂–H₂ atmospheres on Cu/SiO₂ catalysts by simultaneous IR and MS measurements, both steady-state and transient. Studies of isotopic variants (H/D, ¹²C/¹³C) reveal that bidentate formate dominates the copper surface at steady state. The steady-state formate coverages of HCOO (in 6 bar 3:1 H₂:CO₂) and DCOO (in D₂:CO₂) are similar and the steady-state formate coverages in both systems decrease by ~80% from 350 K to 550 K. Over the temperature range 413 K–553 K, the steady-state methanol synthesis rate shows a weak H/D isotope effect (1.05 ± 0.05) with somewhat higher activation energies in H₂:CO₂ (79 kJ/mole) than D₂:CO₂ (71 kJ/mole) over the range 473 K–553 K. The reverse water gas shift (RWGS) rates are higher than methanol synthesis and also shows a weak positive H/D isotope effect with higher activation energy for H₂/CO₂ than D₂/CO₂ (108 vs. and 102 kJ/mole) The reactivity of the resulting formate species in 6 bar H₂, 6 bar D₂ and 6 bar Ar is strongly dominated by decomposition back to CO₂ and H₂. H₂ and D₂ exposure compared to Ar do not enhance the formate decomposition rate. The decomposition profiles on the supported catalyst deviate from first order decay, indicating distributed surface reactivity. The average decomposition rates are similar to values previously reported on single crystals. The average activation energies for formate decomposition are 90 ± 17 kJ/mole for HCOO and 119 ± 11 kJ/mole for DCOO. By contrast to the catalytic reaction rates, the formate decomposition rate shows a strong H/D kinetic isotope effect (H/D ~8 at 413 K), similar to previously observed values on Cu(110).     

SO2 absorption/desorption performance of renewable phenol-based deep eutectic solvents

Six renewable DESs prepared from choline chloride (CC) and phenols (guaiacol, GC; cardanol, CL) with molar ratios of phenols to CC of 3:1, 4:1 and 5:1 were investigated to absorb SO₂ at 293.15–323.15 K and 0–1.0 bar. Results showed that DESs demonstrated satisfactory SO₂ absorption performance, and GC–CC (3:1) exhibited the maximum absorption capacity of 0.528 g SO₂ per g DES. The SO₂ enriched DESs could be easily regenerated and recycled five times. Moreover, the DESs exhibited high selectivity of SO₂/CO₂. Present DESs seem to be promising absorbents for SO₂ due to good performance.     

Determination of the Optimum Conditions for Copper Leaching from Chalcopyrite Concentrate Ore Using Taguchi Method

The optimum conditions for the extraction of copper from chalcopyrite concentrate into SO₂-saturated water were evaluated using the Taguchi optimization method. High level copper recovery was obtained in an environmentally friendly process that avoids sulfur dioxide emission into the atmosphere because SO₂ forming in the roasting is used in the dissolution. Experimental parameters and their ranges were chosen as follows: reaction temperature, 293–333 K; solid-to-liquid ratio, 0.025–0.15 g/mL; roasting time, 30–90 min; roasting temperature, 773–973 K; stirring speed, 400–800 rpm; and reaction time, 10–60 min. The particle size and gas flow rate were 63 µm and 10 cm³/min, respectively. The optimum conditions of the dissolution process were determined to be reaction temperature of 318 K, a solid-to-liquid ratio of 0.025 g mL^?1, a roasting time of 75 min, a roasting temperature of 773 K, a stirring speed of 400 rpm, and a reaction time of 30 min. Under optimum conditions, dissolution yield of copper was 91%.     

Supercritical Carbon Dioxide Extraction of Uranium from Acidic Medium Employing Calixarenes

Various calixarenes were evaluated for the supercritical fluid extraction of uranium from nitric acid medium. The extraction efficiency was found to be affected by various parameters, namely pressure, temperature, CO₂ flowrate, extraction time, and molarity of nitric acid. The addition of HPFOA (pentadecafluoro-n-octanoic acid) for the production of CO₂-phillic fluorinated counter ion enhanced the extraction efficiency. Under optimized conditions (pressure of 200 atm, temperature of 323 K, 30 minutes of static time followed by 30 minutes of dynamic time, CO₂ flowrate of 2 mL min^?1, nitric acid molarity of 0.1 M) for uranium: calixarene: HPFOA mole ratio of 1:5:10, highest extraction efficiency could be obtained with p-tert.-butyl calix[6]arene (79.9%). Solvent extraction study with hexane as the organic phase indicated the formation of [UO₂ (calixarene)]²⁺. In order to assess the suitability of the developed method to extract uranium in the presence of a host of other ions, extraction efficiency for other metal ions was estimated.