Kinetic behaviour of boron selective resins for boron removal using seeded microfiltration system

In this study, boron selective ion exchange resins (Dowex-XUS 43594.00 and Purolite S 108) and model boron solutions at different ionic strengths were used in order to perform continuous kinetic studies in a seeded microfiltration stirred cell provided by Micropore Technologies (UK). Mass transfer modelling based on a well stirred system, including maximum capacity (Q_m, mg/g) and Langmuir constant (b, L/mg) values obtained from a Langmuir isotherm, coupled with film diffusion around the resin particle and internal diffusion within the particle, was used to predict concentration change of boron against time. Finally, experimental results were compared with the modelling data for different ionic strength mediums to determine the diffusivity of boron inside the resin and mass transfer coefficients.     

Synthesis of chitosan beads as boron sorbents

Parameters, such as pH, temperature, initial boron concentration, adsorbent dosage, and ionic strength, affecting boron adsorption onto chitosan beads were examined in this study. The following values were obtained as the optimum conditions in our studied ranges: pH 8.0, temperature = 308 K, amount of chitosan beads = 0.15 g, initial boron concentration = 4 mg L⁻¹, and ionic strength = 0.1 M NaCl]. The adsorption kinetics were also examined in terms of three kinetic models: the pseudo‐first‐order, pseudo‐second‐order, and intraparticle diffusion models. The pseudo‐second‐order kinetic model showed very good agreement with the experimental data. Intraparticle plots seemed to have two steps and indicated multilinearity. Equilibrium data were evaluated with nonlinear and linear forms of the Langmuir and Freundlich equations. The experimental data conformed to the Freundlich equation on the basis of the formation of multilayer adsorption. To characterize the synthesized chitosan beads, we used Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) analyses. As shown by FTIR analysis, the boron species may have interacted with the NH₂ groups on chitosan. Microparticles of about 5 μm appeared in the SEM micrographs of the chitosan beads. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermodynamic,kinetic, and equilibrium studies on phenol removal by use of cashew nut shell

Adsorption of phenol from aqueous solution onto cashew nut shell (CNS) was investigated to assess the possible use of this adsorbent. The influence of various parameters such as contact time, phenol concentration, adsorbent dose, pH, and temperature has been studied. Studies showed that the pH of aqueous solutions affected phenol removal as a result of decrease in removal efficiency with increasing solution pH. The experimental data were analysed by the Langmuir equation. Equilibrium data fitted well with the Langmuir model with maximum monolayer adsorption capacity of 5.405 mg/g. Thermodynamic parameters such as ΔG°, ΔH°, and ΔS° have also been evaluated and it has been found that the sorption process was feasible, spontaneous, and exothermic in nature. The pseudo‐first‐order and pseudo‐second‐order kinetic models were selected to follow the adsorption process. Kinetic parameters, rate constants, equilibrium sorption capacities and related correlation coefficients, for each kinetic model were calculated and discussed. It was shown that the adsorption of phenol could be described by the pseudo‐second‐order equation, suggesting that the adsorption process is presumable a chemisorption. The CNS investigated in this study showed good application potential for the removal of phenol from aqueous solution.     

Equilibrium and Kinetic Studies for Fluoride Adsorption from Water on Zirconium Impregnated Coconut Shell Carbon

Abstract

The batch adsorptive fluoride removal from water by Zirconium ion impregnated coconut shell carbon (ZICSC) was investigated. ZICSC was found to have fluoride adsorption capacity, 25 to 30 times that of plain activated carbon. The effect of various parameters such as pH, agitation time, and adsorbent dosage on fluoride removal were studied. The fluoride adsorption by ZICSC was above 90% for the entire pH range of 2–9 and the adsorption rate was extremely rapid, with 91% of the adsorption being achieved within 10 min of ZICSC contact for an initial fluoride concentration of 10 mg/L. The experimental data have been analyzed by Langmuir, Freundlich, Redlich‐Peterson, and Temkin sorption isotherm models and the adsorption data for fluoride onto ZICSC were better correlated to the Langmuir isotherm. The batch adsorption kinetics have been tested by first order, pseudo‐first order, and pseudo‐second order kinetic models with the subsequent determination of the rate constants of adsorption. The comparison of ZICSC with other adsorbents suggests that ZICSC provides a cost‐effective working solution to the defluoridation problem in the developing countries by its great potential application in fluoride removal from water.     

Utilization of Raw and Activated Date Pits for the Removal of Phenol from Aqueous Solutions

Activated carbons prepared from date pits, an agricultural waste byproduct, have been examined for the adsorption of phenol from aqueous solutions. The activated carbons were prepared using a fluidized bed reactor in two steps; carbonization at 700 °C for 2 hours in N₂ atmosphere and activation at 900 °C in CO₂ atmosphere. The kinetic data were fitted to the models of intraparticle diffusion, pseudo‐second order, and Lagergren, and followed more closely the pseudo‐second‐order chemisorption model. The isotherm equilibrium data were well fitted by the Freundlich and Langmuir models. The maximum adsorption capacity of activated date pits per Langmuir model was 16 times higher than that of nonactivated date pits. The thermodynamic properties calculated revealed the endothermic nature of the adsorption process. The uptake of phenol increased with increasing initial phenol concentration from10 to 200 ppm and temperature from 25 to 55 °C, and decreased with increasing the solution pH from 4 to 12. The uptake of phenol was not affected by the presence of NaCl salt.     

Removal of nickel from aqueous solutions by citric acid modified Ceiba pentandra hulls: Equilibrium and kinetic studies

The removal of Ni(II) from aqueous solutions using biomass prepared from Ceiba pentandra hulls powder modified with citric acid treatment (CAMCPH) has been studied by batch method. The biosorbent was characterised before and after citric acid modification using SEM, FT‐IR and XRD. Experimental parameters that influence the biosorption of Ni(II), such as pH, biosorbent dose, contact time and initial concentration of metal ion have been investigated. The adsorption of Ni(II) increased with increase in contact time and reached equilibrium within 50 min. The maximum removal of Ni(II) was observed at pH 5.0. The kinetic data were analysed using three adsorption kinetic models: the pseudo‐first, second‐order kinetics and intra‐particle diffusion. The results showed that the pseudo‐second‐order model fits the experimental data very well. The equilibrium data were analysed using Langmuir, Freundlich and Dubinin–Radushkevich isotherm models. Langmuir model provided the best correlation for the adsorption of Ni(II) by CAMCPH and the monolayer biosorption capacity for Ni(II) removal was 34.34 mg/g. Desorption experiments were carried out using HCl solution and the recovery of the metal ion from CAMCPH was found 98%. Desorption experiments showed the feasibility of regeneration of the biosorbent for further use after treating with dilute HCl. © 2011 Canadian Society for Chemical Engineering     

Investigation of adsorption of lead,mercury and nickel from aqueous solutions onto carbon aerogel

Recently a new form of activated carbon has appeared: carbon aerogel (CA). Its use for the removal of inorganic (and especially metal ions) has not been studied. In the present study, the adsorption of three metal ions, Hg(II), Pb(II) and Ni(II), onto carbon aerogel has been investigated. Batch experiments were carried out to assess adsorption equilibria and kinetic behaviour of heavy metal ions by varying parameters such as agitation time, metal ions' concentration, adsorbent dose and pH. They facilitated the computation of kinetic parameters and maximum metal ion adsorption capacities. Increasing the initial solution pH (2–10) and carbon concentration (50–500 mg per 50 cm³) increases the removal of all three metal ions. A decrease of equilibrium pH with an increase of metal ion concentration led us to propose an adsorption mechanism by ion exchange between metal cations and H⁺ at the carbon aerogel surface. Carboxylic groups are especially involved in this adsorption mechanism. Langmuir and Freundlich isotherm models were used to analyse the experimental data of carbon aerogel. The thermodynamics of the metal adsorption was also investigated for the practical implementation of the adsorbent. The sorption showed significant increase with increase of temperature. Kinetics models describing the adsorption of Hg(II), Pb(II) and Ni(II) ions onto carbon aerogel have been compared. Kinetics models evaluated include the pseudo‐first order and second order model. The parameters of the adsorption rate constants have been determined and the effectiveness of each model assessed. The result obtained showed that the pseudo‐second order kinetic model correlated well with the experimental data and better than the pseudo‐first order model examined in the study. Mass transfer coefficients obtained can be useful in designing wastewater treatment systems or in the development of environmental technologies. Copyright © 2005 Society of Chemical Industry     

Removal of Basic Blue 3 by sorption onto a weak acid acrylic resin

A weak acid acrylic resin was used as an adsorbent for the investigation of Basic Blue 3 (BB3) adsorption kinetics, isotherms, and thermodynamic parameters. Batch adsorption studies were carried out to evaluate the effect of pH, contact time, initial concentration (28–100 mg/g), adsorbent dose (0.05–0.3 g), and temperature (290–323 K) on the removal of BB3. The adsorption equilibrium data were analyzed by the Langmuir, Temkin, and Freundlich isotherm models, with the best fitting being the first one. The adsorption capacity (Q_o) increased with increasing initial dye concentration, adsorbent dose, and temperature; the highest maximum Q_o (59.53 mg/g) was obtained at 323 K. Pseudo‐first‐order and pseudo‐second‐order kinetic models and intraparticle diffusion models were used to analyze the kinetic data; good agreement between the experimental and calculated amounts of dye adsorbed at equilibrium were obtained for the pseudo‐second‐order kinetic models for the entire investigated concentrations domain. Various thermodynamic parameters, such as standard enthalpy of adsorption (ΔH^o = 88.817 kJ/mol), standard entropy of adsorption (ΔS^o = 0.307 kJ mol^?1 K^?1), and Gibbs free energy (ΔG^o < 0, for all temperatures investigated), were evaluated and revealed that the adsorption process was endothermic and favorable. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Removal of Brill Red 5B from an aqueous solution using Cicca acida biomass

The biosorption of Brill Red 5B from an aqueous solution, using Cicca acida plant's leaves was investigated in a batch system with the influence of pH (1–6), temperature (25–35°C) and initial dye concentration (10–100 mg/L). Maximum biosorption was observed at initial pH of 2.0, temperature of 30°C and at the initial dye concentration of 100 mg/L. Batch biosorption kinetic was studied using the pseudo first and pseudo‐second‐order rate equations. From the result, it was observed that pseudo‐second‐order rate expression fitted the experimental data well when compared to pseudo first order kinetic model. The intra‐particle diffusion coefficient (K_i) and effective diffusion coefficient (D_i) values obtained for the sorption of Brill Red 5B using C. acida plant's leaves were found to be increased with increase in initial dye concentration.     

Study on adsorption characteristic of macroporous resin to phenol in wastewater

The removal of phenol from solution was investigated using macroporous resin. The effects of initial concentration, pH, and temperature on phenol removal were studied. The experimental results indicated that the adsorption capacity reached equilibrium state within 20 min and adsorption followed pseudo‐second‐order kinetic model. Langmuir isotherm model could be better to describe the isothermal adsorption of phenol, the maximum adsorption capacity (Q_m) and Langmuir constant (K_L) were 103.64 mg/g and 0.2719. Macroporous resin after reached to saturation has a high desorption percentage, indicating that H‐103 is an excellent reusing adsorption material. It provided theoretical references for practical application in phenolic wastewater treatment.     

Adsorption isotherms,kinetic, and desorption studies on removal of toxic metal ions from aqueous solutions by polymeric adsorbent

Adsorption of Cd(II), Co(II), and Ni(II) on aminopyridine modified poly(styrene‐alt‐maleic anhydride) crosslinked by 1,2‐diaminoethane as an ion exchange resin has been investigated in aqueous solution. Adsorption behavior of these metal ions on the resin was studied by varying the parameters such as pH (2–6), adsorbent dose (0–4.0 g/L), contact time (0–240 min), and metal ions concentration (20–300 mg/L). Adsorption percentage was increased by increasing each of these parameters. The isotherm models such as: Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich were used to describe adsorption equilibrium. The results showed that the best fit was achieved with the Langmuir isotherm equation, yielding maximum adsorption capacities of 81.30, 49.02, and 76.92 mg/g for Cd(II), Co(II), and Ni(II), respectively. The pseudo‐first‐order, pseudo‐second‐order, and intra‐particle diffusion kinetics equations were used for modeling of adsorption data and it was shown that pseudo‐second‐order kinetic equation could best describe the adsorption kinetics. The intra‐particle diffusion study revealed that external diffusion might be involved in this case. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41642.     

Pectin‐[(3‐acrylamidopropyl) trimethylammonium chloride‐co‐acrylic acid] hydrogel prepared by gamma radiation and selectively silver (Ag) metal adsorption

Pectin‐[(3‐acrylamidopropyl) trimethylammonium chloride‐co‐acrylic acid] hydrogel has been prepared from the aqueous blend solution of pectin, (3‐acrylamidopropyl) trimethylammonium chloride (APTAC), and acrylic acid (AAc) by applying gamma radiation of different doses (1–25 kGy) from ⁶⁰Co gamma source. The hydrogels were characterized by equilibrium swelling, Fourier transform infrared, differential scanning calorimetry, and scanning electron microscopy. The hydrogels were used in multielement adsorption and it was found that pectin‐(APTAC‐co‐AAc) gel is highly selective toward silver (I) ion among 27 metal ions. The data obtained from equilibrium adsorption studies were fitted in Langmuir and Freundlich adsorption isotherm models and model parameters evaluated. The maximum adsorption capacity of pectin‐(APTAC‐co‐AAc) gel was found to be 67.6413 mg/g of dry gel at sample volume of 25 mL. The kinetic data were tested using pseudo‐first order and pseudo‐second order kinetic models and different adsorption diffusion models such as film diffusion and intra‐particle diffusivity model. Thiourea solution was used for desorption of adsorbed metal ions from the hydrogel. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45906.     

Preparation and characterization of porous chitosan–tripolyphosphate beads for copper(II) ion adsorption

Porous chitosan–tripolyphosphate beads, prepared by the ionotropic crosslinking and freeze‐drying, were used for the adsorption of Cu(II) ion from aqueous solution. Batch studies, investigating bead adsorption capacity and adsorption isotherm for the Cu(II) ion, indicated that the Cu(II) ion adsorption equilibrium correlated well with Langmuir isotherm model. The maximum capacity for the adsorption of Cu(II) ion onto porous chitosan–tripolyphosphate beads, deduced from the use of the Langmuir isotherm equation, was 208.3 mg/g. The kinetics data were analyzed by pseudo‐first, pseudo‐second order kinetic, and intraparticle diffusion models. The experimental data fitted the pseudo‐second order kinetic model well, indicating that chemical sorption is the rate‐limiting step. The negative Gibbs free energy of adsorption indicated a spontaneous adsorption, while the positive enthalpy change indicated an endothermic adsorption process. This study explored the adsorption of Cu(II) ion onto porous chitosan–tripolyphosphate beads, and used SEM/EDS, TGA, and XRD to examine the properties of adsorbent. The use of porous chitosan–tripolyphosphate beads to adsorb Cu(II) ion produced better and faster results than were obtained for nonporous chitosan–tripolyphosphate beads. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chemically Modified CaO/Fe3O4 Nanocomposite by Sodium Dodecyl Sulfate for Cr(III) Removal from Water

A CaO/Fe₃O₄ nanocomposite was modified by sodium dodecyl sulfate (SDS) and used for Cr(III) removal from aqueous solution. The physical and surface characteristics of the adsorbent were studied by different analysis techniques. The effects of key parameters such as pH, contact time, temperature, initial concentration of Cr(III) ions, and adsorbent dose were investigated at a fixed mixing rate. Parameters were optimized to attain the best possible removal efficiency of Cr(III) ions. The maximum adsorption capacities obtained from the Langmuir model were determined. The results of equilibrium and kinetic studies indicate that the adsorption process follows the Langmuir isotherm model and the pseudo‐second‐order kinetic model. The thermodynamic study demonstrated that the adsorption process was suitable, spontaneous, and exothermic.     

Preparation and characterization of selective phenyl thiosemicarbazide modified Au(III) ion‐imprinted cellulosic cotton fibers

In this study, a novel selective Au(III) chelating surface ion imprinted fibers based on phenyl thiosemicarbazide modified natural cotton (Au‐C‐PTS) has been synthesized, and applied for selective removal of Au(III) from aqueous solutions. Batch adsorption experiments were performed with various parameters, such as contact time, pH, initial Au(III) concentration, and temperature. The kinetic studies revealed that the adsorption process could be described by pseudo‐second‐order kinetic model, while the adsorption data correlated well with the Langmuir and Freundlich models. The maximum adsorption capacities calculated from the Langmuir equation are 140 ± 1 mg g^?1 and 72 ± 1 mg g^?1 at pH 5 for both Au‐C‐PTS and NI‐C‐PTS, respectively. The estimated thermodynamic parameters (Gibbs free energy (ΔG°), enthalpy (ΔH°), and entropy change (ΔS°)) indicated the spontaneity and exothermic nature of the adsorption process. Furthermore, the selectivity study revealed that the ion imprinted fibers was highly selective to Au(III) compared with Cu(II), Cd(II), Hg(II), and Fe(III). The adsorbent was successfully regenerated with a 0.1M HNO₃ solution. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40769.     

The use of Jatobá bark for removal of cationic dyes

In this work, the application of Jatobá bark (the waste product of medicinal plant processing) in removal of the cationic dyes Methylene Blue, Crystal Violet and Rhodamine B from aqueous solution was studied in a batch system. The effect of contact time, pH and temperature on dye removal was investigated. An increase in pH from 2 to 10 was accompanied by an increase in the amount of dye adsorbed. The equilibrium sorption data fitted to the Langmuir, Freundlich and Langmuir–Freundlich equations were investigated. The Langmuir–Freundlich isotherm exhibited the best fit with the experimental data and the maximum adsorption capacities at room temperature being 211.5, 89.5 and 69.4 for Rhodamine B, Methylene Blue and Crystal Violet, respectively. The kinetic sorption was evaluated by the pseudo‐first‐order, pseudo‐second‐order and intraparticle diffusion models. It was observed that sorption follows the pseudo‐second‐order kinetic model. The thermodynamic parameters for the sorption process were also determined. The spontaneous and endothermic nature of adsorption was obtained based on the negative value of free energy (ΔG) and the positive value of enthalpy (ΔH). The results indicate that Jatobá bark could be used as a low‐cost material for the removal of cationic dyes from wastewater.     

Nano-TiO2 modified with 2-mercaptobenzimidazole as an efficient adsorbent for removal of Ag(I) from aqueous solutions

Nano-TiO₂ was modified with 2-mercaptobenzimidazole via surfactant activation and used as an adsorbent for the removal of Ag(I) under optimum conditions. The adsorbent was characterized using powder X-ray diffraction and FT-IR spectroscopy. The equilibrium data were fitted to the Langmuir, Freundlich and Temkin isotherm models. Langmuir isotherm describes the adsorption data better than Freundlich isotherm and Temkin. Kinetic studies showed that the pseudo second order kinetic model fits the adsorption kinetic processes well. Maximum adsorption capacity for Ag(I) was 128.2 mg g⁻¹ of nano-TiO₂. The method was successfully applied to the removal of silver from radiology film processing wastewater samples.     

Cadmium(II) biosorption from aqueous solutions using Hydrilla verticillata

The kinetics and equilibrium of cadmium biosorption from aqueous solutions were investigated using fresh tissues of Hydrilla verticillata. The biosorptive characteristics of cadmium ions were studied with respect to well‐established effective parameters, including pH, temperature and contact time. The biosorptive capacity of H. verticillata for cadmium increased with increasing pH. In addition, the resulting isotherms were well‐described by Langmuir and extended Langmuir models (R² = 0.9794–0.9957 and 0.9880, respectively). The comparison between calculated and experimental q_e values showed that the extended Langmuir model had a better simulation for the cadmium biosorption by H. verticillata than the Langmuir isotherm model. The equilibrium biosorption data at a constant temperature were well‐interpreted by the Langmuir model. The maximum biosorptive capacity increased from 33.54 to 37.46 mg/g when the solution temperature was increased from 278 to 298 K. Other various thermodynamic parameters were also estimated. Biosorptive equilibrium was established within approximately 20 min. Moreover, the pseudo‐second‐order equation was more appropriate in predicting biosorptive capacity than the pseudo‐first‐order equation. In practical viewpoints, the abundant and inexpensive plant biomass H. verticillata can be used as an effective and environmentally friendly biosorbent for the detoxification of cadmium from aqueous solutions. © 2012 Canadian Society for Chemical Engineering     

Synthesis of novel polyaniline/MgO composite for enhanced adsorption of reactive dye

In this investigation, the porous structure of polyaniline/MgO (PANI/MgO) composites has been successfully synthesized by in‐situ oxidative polymerization method. The as‐prepared materials were characterized by Ultraviolet–visible absorption spectroscopy, Fourier transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy. The obtained composites, for the first time, are used as an adsorbent for the removal of the sulfonated anionic dye reactive orange 16 (RO) from aqueous solution. The equilibrium adsorption isotherms of RO on the PANI/MgO composites were analyzed by Langmuir and Freundlich models, suggesting that the Langmuir model provides the better correlation of the experimental data and maximum adsorption capacity was found to be 558.4 mg g^?1. In addition, adsorption kinetics was followed by both pseudo‐first‐order and pseudo‐second‐order, but the latter model matches the results much better than the former one. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40210.     

Surfactant‐modified feldspar: Isotherm,kinetic, and thermodynamic of binary system dye removal

In this article, surface modification of feldspar using hexadecyltrimethyl ammonium bromide (HDTMA) and its dye removal ability in single and binary systems was studied. Acid Black 1 (AB1) and Acid Red 14 (AR14) were used as model dyes. The monocomponent Langmuir isotherm model was applied to experimental data and the isotherm constants were calculated for both dyes. The monolayer coverage capacities of surfactant‐modified feldspar (HDTMA‐feldspar) for AB1 and AR14 dyes in single solution system were found as 6.369 mg/g and 3.984 mg/g, respectively. It was observed that the equilibrium uptake amounts of AB1 and AR14 dye in binary mixture onto sorbent decreased with increasing concentrations of the other dye resulting in their antagonistic effect. Equilibrium adsorption for binary systems was analyzed by using the Extended Langmuir and Jain and Snoeyink Modified Extended Langmuir models. The rate of kinetic processes of single and binary dye systems onto adsorbent was described by using two kinetics adsorption models. The pseudo‐second‐order model was the best choice among the kinetic models to describe the adsorption behavior of single and binary dyes onto HDTMA‐feldspar. Thermodynamic parameters showed that dye adsorption on HDTMA‐feldspar were exothermic and unspontaneous in nature. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012