Anionic dye adsorption characteristics of surfactant‐modified coir pith,a ‘waste’ lignocellulosic polymer

The surface of coir pith, an agricultural solid waste, was modified using a cationic surfactant hexadecyltrimethylammonium bromide. Adsorption of anionic dyes on surfactant‐modified coir pith was investigated in a series of batch adsorption experiments. Two anionic dyes, acid brilliant blue (acid dye) and procion orange (reactive dye), were used in the adsorption studies. The effect of process variables such as contact time, concentration of the dyes, adsorbent dose, temperature, and pH were studied in order to understand the kinetic and thermodynamic parameters of the process. The kinetics of adsorption obeyed the second‐order rate equation. The equilibrium adsorption data were fitted into the Langmuir and Freundlich isotherms. It was found that modified coir pith yielded adsorption capacities of 159 and 89 mg/g for acid brilliant blue and procion orange, respectively. Mechanisms involving ion exchange and chemisorption might be responsible for the uptake of dyes. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1538–1546, 2006     

Synthesis and application to cotton of a polymeric black colorant prepared by grafting of reactive dyes to polyvinylamine

A novel polymeric black dye was synthesised by grafting yellow, orange, red, and blue reactive dyes onto polyvinylamine. Such a polymeric black dye takes the onus away from dyers to worry about the compatibility of individual dyes. The polymeric black dye was characterised by Fourier transform infrared, ultraviolet‐visible, and nuclear magnetic resonance spectroscopy. The absorption of the polymeric black dye in aqueous solution was nearly constant across the wavelength range 400–700 nm. Compared with a black mixture of reactive dyes with low fixation on cotton, which was prepared by mixing yellow, orange, red, and blue reactive dyes, the polymeric black dye reached 99% fixation on cotton through the use of a crosslinking agent. The colorimetric properties of cotton dyed with the polymeric black dye and with the black mixture of reactive dyes showed that better blackness can be obtained by using the polymeric black dye. Analysis of the thermal stability and penetration ability of the polymeric black dye showed that the polymeric dye has high stability in the application and a uniform distributution in the cotton fabric.     

Synthesis and characterization of polyamide powders for sorption of reactive dyes from aqueous solutions

Polyamide (PA) fine powders or granules, obtained by anionic solution/suspension polymerization of lactams, were used for the sorption of reactive dye Brilliant Red HE‐3B from aqueous solutions. They provided a relatively large surface area and porosity that allowed an increased sorption rate. The visible molecular absorption spectroscopy was used to evaluate the performance of the investigated systems. Under the same conditions, the sorption capacity of polyamide particles decreases in the following manner: PA6‐powders > PA12‐powders > PA4‐granules. The effect of pH, initial dye concentration, temperature, and sorption duration on dye removal was studied for the PA6‐powder/reactive dye system. The equilibrium sorption isotherms have been analyzed by the linear, Freundlich, and Langmuir models. The data conform to a Langmuir isotherm and a pseudosecond order kinetic model, respectively. In addition, the apparent thermodynamic parameters were calculated and the obtained values support the conclusion that the reactive dye molecules are adsorbed onto PA‐powders by an entropy‐driven, endothermic process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Influence of dyes, salts and auxiliary chemicals on the nanofiltration of reactive dye baths: experimental observations and model verification

The aim of this study was to investigate the effects of dyes, salts and auxiliary chemicals in reactive dye baths on the separation performance of nanofiltration membranes. A reactive dye bath was simulated for this purpose with auxiliary chemicals. A DS5-type nanofiltration membrane was used in the experimental runs. Performance of the nanofiltration membrane was evaluated by measuring permeate flux, salt and color rejections in five steps. Reactive black 5, reactive orange 16, NaCl, NaOH, Na₂SO₄, acidic acid, mollan and slipper were used to prepare synthetic dye baths. Pressures in the range of 8 to 24 bars were applied, and flow velocity was kept constant at 0.74 m/s. NaCl rejection of 20% and color rejection of more than 95% were achieved throughout the experiments. Permeate quality was satisfactory enough to recycle these effluents in reactive dyeing. Acidification ofthe original synthetic dye bath solution with HCl and H₂S0₄ decreased the membrane fouling and also increased the NaCl recovery and color rejection. Besides, using HCI instead of H₂SO₄ increased these positive effects. The effects of auxiliary chemicals were determined by using salt rejection model parameters of α and k_D in the presence of an organic ion. There was a correlation among the results of experiments and the model. The model parameters (α and k_D were also calculated for all steps.     

New carbon composite adsorbents for the removal of textile dyes from aqueous solutions: Kinetic,equilibrium, and thermodynamic studies

New carbon composite materials were prepared by pyrolysis of mixture of coffee wastes and red mud at 700 °C with the inorganic: organic ratios of 1.9 (CC-1.9) and 2.2 (CC-2.2). These adsorbents were used to remove reactive orange 16 (RO-16) and reactive red 120 (RR-120) textile dyes from aqueous solution. The CC-1.9 and CC-2.2 materials were characterized using Fourier transform infrared spectroscopy, Nitrogen adsorption/desorption curves, scanning electron Microscopy and X-ray diffraction. The kinetic of adsorption data was fitted by general order kinetic model. A three-parameter isotherm model, Liu isotherm model, gave the best fit of the equilibrium data (298 to 323 K). The maximum amounts of dyes removed at 323 K were 144.8 (CC-1.9) and 139.5 mg g^?1 (CC-2.2) for RO-16 dye and 95.76 (CC-1.9) and 93.80 mg g^?1 (CC-2.2) for RR-120 dye. Two simulated dyehouse effluents were used to investigate the application of the adsorbents for effluent treatment.     

Batch Removal of Crystal Violet from Aqueous Solution by H2SO4 Modified Sugarcane Bagasse: Equilibrium,Kinetic, and Thermodynamic Profile

Batch adsorption studies were carried out using H₂SO₄ modified sugarcane bagasse (HMSB) for the removal of hazardous Crystal Violet (CV) dye from aqueous solutions. The effects of initial solution pH, adsorbent dose, and temperature on the adsorption process were investigated. The Langmuir isotherm model well described the equilibrium dye uptake while the pseudo-second-order kinetic model showed good agreement with the experimental kinetic data. Gibb's free energy change (ΔG⁰) was spontaneous for all interactions, and the adsorption process exhibited endothermic enthalpy values. Results suggest that HMSB is an effective adsorbent for the removal of CV from wastewater.     

Adsorption behavior of Congo red from an aqueous solution on 4‐vinyl pyridine grafted poly(ethylene terephthalate) fibers

In this study, a reactive fibrous adsorbent was prepared through the grafting of 4‐vinyl pyridine monomer onto poly(ethylene terephthalate) (PET) fibers for the removal of Congo red (CR) dye from an aqueous solution with the batch adsorption method. Effects of various parameters such as the grafting yield, pH, treatment time, and initial dye concentration on the amount of adsorption of the dye onto the reactive fibers were investigated. The effective pH was 4.0 for adsorption on grafted PET fibers. The sufficient time to attain equilibrium was 150 min. The maximum adsorption capacity of the reactive fibers for CR was 17.3 mg/g of fiber. The rates of adsorption conformed to pseudo‐second‐order kinetics with good correlation. The adsorption isotherm of CR fit a Langmuir‐type isotherm. The reactive fibers were stable and regenerable by acid and base without loss of activity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Biosorption of anionic dyes from aqueous solutions using a novel magnetic nanocomposite adsorbent based on rice husk ash

This study investigated the potential use of an agricultural waste, rice husk ash, for the removal of methyl orange. The adsorbent was prepared via a simple one-pot synthesis of magnetic iron oxide nanoparticles (MIONs). The prepared magnetic nanocomposites were characterized using Fourier transform infrared, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and vibrating sample magnetometer techniques. Bach adsorption experiments were carried out to evaluate the effects of initial dye concentration, pH and contact time as well as MION content on adsorption capacity. The mechanism of dye adsorption was well fitted to a pseudo-second-order kinetic model. Moreover, the equilibrium data fitted well with the Langmuir isotherm model.     

A hemicyanine fluorescent reactive cationic dye: synthesis and applications on wool fabrics

A novel hemicyanine fluorescent reactive cationic dye was synthesised by the reaction between the free amino group of a hemicyanine fluorescent dye and 2,3‐dibromopropionyl chloride. The dye was characterised by proton nuclear magnetic resonance spectroscopy, high‐resolution mass spectrometry, ultraviolet‐visible absorption spectrometry, and single‐photon fluorescence spectrometry. The prepared dye was applied to wool fabrics to give fluorescent orange shades. The colour fastness of the dyed wool fabrics was tested. Results show that dyed fabrics using the novel hemicyanine fluorescent reactive cationic dye could be used as fluorescent clothing.     

柚子皮吸附活性艳蓝KN-R和活性艳橙X-GN性能研究

采用间歇实验,考察了初始pH、柚子皮投加量、柚子皮粒径、离子强度、染料初始含量及接触时间对柚子皮去除废水中的活性艳蓝KN-R及活性艳橙X-GN这2种染料影响。结果表明,酸性pH条件下吸附效果良好,柚子皮能有效地去除废水中的KN-R和X-GN,对KN-R和X-GN的去除率达到97.48%和95.63%;柚子皮粒径变化对吸附效果影响不明显,吸附时间宜控制在480 min以上。柚子皮可作为一种新型吸附剂应用于活性染料废水的处理,作为一种农业废物的资源化加以利用。     

瓜环的固载化过程及其对甲基橙的吸附动力学

研究了羟基瓜环在氯甲基化聚苯乙烯株（氯球）上的固载动力学及固载影响因素,并研究了固载化瓜环对甲基橙染料的吸附动力学.结果表明,羟基瓜环通过亲核取代反应固载到氯球上,提高固载温度和提高羟基瓜环的投加量有利于瓜环的固载.羟基瓜环在氯球上的固载动力学符合准二级动力学方程.固载化瓜环对甲基橙的吸附动力学符合准二级动力学模型,而准一级动力学模型适合吸附过程的初始阶段,吸附过程受颗粒内扩散控制,但不是吸附速率的唯一控制因素,整个吸附过程是多种动力学机理共同作用的结果.     

The use of chromium waste sludge for the adsorption of colour from dye effluent streams

Adsorption studies show that chromium hydroxide precipitates can be used for the removal of methylene blue, reactive blue, congo red and disperse orange dyes from aqueous media. Three different mechanisms are involved: attraction of positive surface charges on the precipitate at low pH for dye anions (reactive blue and congo red); attraction of negative surface charges on hydroxide at high pH for dye cations (methylene blue), and dye particle entrapment for the neutral disperse orange. The point of zero charge of the chromium hydroxide precipitate based on the dye adsorption studies is pH 10.5. The changes in the surface charge of such precipitates with pH can be used to achieve the removal of any charged dye species. © 2002 Society of Chemical Industry     

Sorption of Brilliant Red HE-3B Reactive Dye from Aqueous Solution onto Seashells Waste: Equilibrium and Kinetic Studies

The potential of waste seashells powder, as a new adsorbent for Brilliant Red HE-3B reactive dye removal from aqueous solutions, was examined by the batch technique. The Freundlich, Langmuir, and Dubinin-Radushkevich adsorption models were applied to describe the equilibrium sorption data and to determine the corresponding isotherm constants. The values of the thermodynamic parameters, ΔG, ΔH, and ΔS, indicate that the sorption of reactive dye is a spontaneous and endothermic process. The kinetic data evaluated by pseudo-first order, pseudo-second order, and intraparticle diffusion kinetic models suggested that the sorption of reactive dye onto seashell is a complex process and both surface sorption and intraparticle diffusion contributes to the rate limiting step.     

EFFECT OF TEMPERATURE ON THE ADSORPTION OF METHYLENE BLUE DYE ONTO SULFURIC ACID–TREATED ORANGE PEEL

The present study explains the preparation and application of sulfuric acid–treated orange peel (STOP) as a new low-cost adsorbent in the removal of methylene blue (MB) dye from its aqueous solution. The effects of temperature on the operating parameters such as solution pH, adsorbent dose, initial MB dye concentration, and contact time were investigated for the removal of MB dye using STOP. The maximum adsorption of MB dye onto STOP took place in the following experimental conditions: pH of 8.0, adsorbent dose of 0.4 g, contact time of 45 min, and temperature of 30°C. The adsorption equilibrium data were tested by applying both the Langmuir and Freundlich isotherm models. It is observed that the Freundlich isotherm model fitted better than the Langmuir isotherm model, indicating multilayer adsorption, at all studied temperatures. The adsorption kinetic results showed that the pseudo-second-order model was more suitable to explain the adsorption of MB dye onto STOP. The adsorption mechanism results showed that the adsorption process was controlled by both the internal and external diffusion of MB dye molecules. The values of free energy change (ΔG ^o) and enthalpy change (ΔH ^o) indicated the spontaneous, feasible, and exothermic nature of the adsorption process. The maximum monolayer adsorption capacity of STOP was also compared with other low-cost adsorbents, and it was found that STOP was a better adsorbent for MB dye removal.     

氯化物介质中甲基橙的电降解行为研究

采用电催化氧化技术处理一种偶氮染料甲基橙的模拟废水,研究了不同类型支持电解质对甲基橙降解效果的影响,分析了电化学体系中氯离子的作用机理.通过对电流密度、电解质浓度等影响因素,以及中间产物图谱的分析,初步得出了氯化物介质中甲基橙的电降解历程.     

Dyeing properties of silk produced by silkworms reared on artificial and mulberry leaf diets

The dyeing properties were investigated for silk proteins produced by silkworms reared entirely on an artificial diet (A) and a mulberry leaf diet (M). The dyeing experiments were carried out with CI acid orange 7 at pH 3.9 and 60°C. The sericin contents of the A and the M raw silk samples were determined to be 26.0% and 23.7%, respectively. The equilibrium dye uptake and the dyeing rate of the A silk fibroin were almost the same as those of the M silk fibroin. The equilibrium dye uptake on each silk sericin was 3–4 times higher than that of the silk fibroin. On the other hand, the equilibrium dye uptake of the A silk sericin was higher than that of the M silk sericin, but the dyeing rate of the former was slower than that of the latter.     

Efficient biosorption of a reactive dye from contaminated media by Neurospora sitophila cells—Zea mays silk tissue biomass system

BACKGROUND: A filamentous fungus Neurospora sitophila was immobilized in Zea mays silk tissue and the prepared system was employed as a new biosorbent for the treatment of reactive dye contaminated solutions. RESULTS: Decolorization potential of the biosorbent system was investigated in batch and continuous mode operations. Design parameters such as pH, biomass dosage, contact time, temperature, dye concentration and flow rate were investigated. Batch mode equilibrium data were analyzed kinetically to determine the rate constants. The process followed the pseudo‐second‐order kinetic model. The thermodynamics of the biosorption indicated the spontaneous and endothermic nature of the process. Biosorption was well described by the Langmuir isotherm model, with a maximum monolayer biosorption capacity of 105.33 mg g^?1. Relatively good dynamic flow decolorization potential was observed for the biosorbent system in synthetic and real wastewater conditions. Flow mode regeneration studies over ten consecutive cycles indicated that the suggested biosorbent maintained consistently high biosorption yield, above 70%. The possible dye‐biosorbent interaction mechanism was also confirmed by zeta potential, FTIR, SEM and EDX analysis. CONCLUSION: High biosorption capacity and regeneration potential suggest that the new biosorbent system can be used as an alternative and low‐cost biomaterial for the treatment of reactive dye contaminated solutions. Copyright © 2011 Society of Chemical Industry     

Synthesis of novel polyaniline/MgO composite for enhanced adsorption of reactive dye

In this investigation, the porous structure of polyaniline/MgO (PANI/MgO) composites has been successfully synthesized by in‐situ oxidative polymerization method. The as‐prepared materials were characterized by Ultraviolet–visible absorption spectroscopy, Fourier transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy. The obtained composites, for the first time, are used as an adsorbent for the removal of the sulfonated anionic dye reactive orange 16 (RO) from aqueous solution. The equilibrium adsorption isotherms of RO on the PANI/MgO composites were analyzed by Langmuir and Freundlich models, suggesting that the Langmuir model provides the better correlation of the experimental data and maximum adsorption capacity was found to be 558.4 mg g^?1. In addition, adsorption kinetics was followed by both pseudo‐first‐order and pseudo‐second‐order, but the latter model matches the results much better than the former one. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40210.     

Reactive dye removal in dye/salt mixtures by nanofiltration membranes containing vinylsulphone dyes: effects of feed concentration and cross flow velocity

In this study, DS5 DK type nanofiltration membranes were tested to recycle the reactive dye bath effluents. Reactive black 5 (RB5), reactive orange 16 (RO16), reactive blue 19 (RB19) and NaCl were used in the experiments to prepare the synthetic dye and salt mixtures. Effects of feed concentration, pressure and cross flow velocity on the permeate flux and color removal were investigated. Permeate flux increased with increasing pressure for all NaCl solutions. Dye concentration had a significant effect on flux values. Under the fixed NaCl concentrations the flux decreased with increasing dye concentrations. Dye rejections greater than 99% were achieved. Permeate was almost colorless. A gel layer formed by the rejected dye on membrane surface operates as a resistance to the permeation of dyes due to complete rejection of high molecule weight dyes, especially for the low salt concentrations. The presence of salt concentration has an interesting effect on color removal. Color removal decreased with increasing salt concentration. Cross flow velocities had also a significant effect on flux values. The dye formed agglomerates at high NaCl concentrations. High cross flow velocities decreased this effect.     

Fitting of equilibrium and kinetic data for the removal of Novacron Orange P-2R by sugarcane bagasse

In this study, the potential of sugarcane bagasse, to remove Novacron Orange P-2R dye from aqueous solution by adsorption was investigated in batch mode. Different process parameters were optimized for biosorption process. Equilibrium biosorption isotherms, kinetics and thermodynamics were investigated in batch mode. The biosorption data were fitted well to the Langmuir isotherm. The kinetic data obtained at different concentration have been analyzed using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The best fitted kinetic model was found to be pseudo-second-order. The FTIR spectrum was recorded to find out the functional groups involved.