丝状菌对膜生物反应器中溶解性有机物及膜污染的影响

该文以处理超市废水实际MBR工程为基础,通过对污泥膨胀过程中进出水、溶解性微生物产物(SMP)和胞外聚合物(EPS)中的溶解性有机物(DOM)特性的研究,发现SMP和进出水的DOM主要以蛋白质为主,且SMP较EPS含有更多大分子物质;同时发现SMP比EPS和进出水中含有更多50～100 kDa、100～500 kDa和...     

膜生物反应器膜污染的研究进展

从膜的结构性质、反应器操作条件、处理液微生物性质三个方面介绍了膜生物反应器膜污染机理研究的进展,总结了优化膜生物反应器设计、调节膜生物反应器操作条件、在线超声控制、化学方法等膜污染控制的常用方法,对未来膜污染研究进行了展望。     

Operation of Membrane Bioreactor with Powdered Activated Carbon Addition

Abstract

The effect of powdered activated carbon (PAC) addition to the activated sludge (AS) in a membrane bioreactor (MBR) has been investigated. The long term nature of the tests allowed the PAC to gradually incorporate into the biofloc forming biologically activated carbon (BAC). One series of tests involved 4 bench scale (2 L) MBRs operated at sludge retention times (SRTs) of 30 days with PAC inventories of 0, 1, 3 and 5 g/L and steady state biomass concentrations of 12.0±1.0 g/L. The characteristics of the mixed liquors (MLSS) from the 4 reactors were compared. Short term filtration tests, including measurement of specific cake resistance (SCR), flux decline profile, and irreversible fouling resistance in an unstirred cell and “sustainable” flux (by monitoring transmembrane pressure (TMP) rise) in a crossflow cell all showed better filtration performance for the MLSS with BAC compared with the AS alone. In terms of SCR and flux decline profile the 1 g/L PAC addition performed best, but in terms of minimizing irreversible membrane fouling and maximizing “sustainable” flux the 5 g/L PAC was best. All 4 systems showed lower total organic carbon (TOC) in the permeate compared to the bioreactors, but the lowest permeate TOC (and the best removal) was for the highest PAC loading.

The benefit of PAC addition was confirmed in a second series of tests with two 20 L MBRs with submerged hollow fibers, one operated without PAC, the MBR(AS), and the other with 5 g/L PAC, the MBR(BAC). For an SRT of 30 days (which involved 3.3% sludge wastage per day and 3.3% new PAC addition per day) and a fixed flux of 21 L/m²hr the MBR(AS) showed a TMP rise of about 2.4 kPa/day whereas the MBR(BAC) showed a rise of only 0.8 kPa/day. However when the MBRs were operated without wastage the performance of the MBR(BAC) was worse than the MBR(AS). Thus the improved performance of the MBR(BAC) requires regular replenishment of aged BAC with fresh PAC.     

典型金属赋存形态对MBR膜污染影响研究进展

膜污染是膜生物反应器(MBR)进一步发展的最大障碍,污泥混合液性状是影响膜污染的关键因素.本文综述了金属离子在MBR混合液中的赋存形态,并分别对金属离子3种不同赋存形态对MBR污泥混合液及膜分离过程的影响进行了探讨.文中揭示了同价离子或异价离子共存对混合液及膜分离的影响,对共存体系中金属离子间的协同或拮抗行为也进行了讨论,并对利用高价金属离子减缓膜污染领域未来的研究趋势进行了展望.     

膜生物反应器中膜污染机理的研究

在采用膜生物反应器（MBR）处理染料废水的过程中,通过对活性污泥进行终端过滤来反映膜污染机理,着重考察了膜过滤的形式、膜通量变化和膜污染的形成。污泥的终端过滤过程严格符合沉积过滤定律;膜通量随过滤时间呈指数衰减趋势,并在几分钟内就达到相对稳定值;扫描电镜照片也证实了膜污染主要是膜面沉积层引起的。     

膜生物反应器污泥混合液对膜污染影响研究进展

膜生物反应器(membrane bioreactor,MBR)作为一种高效的污水处理及回用工艺,近年来备受关注,然而MBR的膜污染问题严重制约了该工艺进一步快速的商业化推广.本文综述了污泥混合液各组分对MBR膜分离的影响,包括溶解性微生物代谢产物(soluble microbial product,SMP)、胞外聚合物(extracellular polymeric substances,EPS)、污泥浓度(mixed liquor suspended solids,MLSS)、颗粒粒径及无机物对膜污染影响,并对该领域未来的研究方向进行了论述.     

Modeling of Particle Fouling and Membrane Blocking in Submerged Membrane Filtration

Abstract

The models of particle fouling and membrane blocking in a submerged membrane filtration are developed in this study. The effects of operating conditions, such as aeration intensity (air flow rate) and filtration pressure, on the filtration flux, membrane blocking, and cake formation are discussed thoroughly. The experimental results show that the filtration resistances due to cake formation and membrane blocking play significant roles in determining the overall filtration resistance, but the latter one is more dominant. An increase in aeration intensity leads the filtration flux to increase due to the reduction of cake formation on the membrane surface. However, a higher filtration pressure causes more severe membrane internal blocking and then to lower filtration flux. The cake properties and the filtration resistance due to membrane blocking are analyzed and can be regressed to empirical functions of filtration pressure. A force balance model for particle deposition on the membrane surface is also derived. In order to estimate the shear stress acting on the membrane surface, the diameter, shape, and rising velocity of air bubbles are analyzed based on hydrodynamics. Once the model coefficients are obtained, the pseudo‐steady filtration flux under various conditions can be estimated by the proposed model and the basic filtration equation. The calculated results agree fairly well with the available experimental data.     

基于群体淬灭理论MBR减缓膜污染研究进展

膜生物反应器(membrane bioreactor,MBR)已成为一个十分有前景的废水处理工艺,该工艺具有出水水质好、占地面积小等优势.然而,由于微生物附着在膜表面而发生的生物污染现象,致使出水通量下降,限制了MBR的大规模推广应用.最近,一种新兴的、基于群体感应(quorum sensing,QS)的群体淬灭(quorum quenching,QQ)技术在延缓MBR膜污染领域的应用备受关注.QQ通过干扰群体感应系统而阻止其所依赖信号分子的基因表达,从而可有效抑制膜表面生物膜的形成.本文首先介绍了群体感应机理,并根据不同的群体淬灭物质,归纳总结了群体淬灭技术在延缓MBR膜污染的最新研究进展,最后对该领域的研究进行了展望.     

Effect of Hydraulic Retention Time on Sludge Properties,Cake Layer Structure,and Membrane Fouling in a Thermophilic Submerged Aerobic Membrane Bioreactor

Sludge properties, cake layer structure, and membrane fouling in a membrane bioreactor were studied under various hydraulic retention times (HRT). A decrease in HRT resulted in an increase in extracellular polymeric substance production in bulk sludge and changes in cake layer structure from gel layer to one or two cake layers. Particle size distribution in cake sludge changed with respect to HRT. An evolution in cake layer thickness and porosity was observed with trans-membrane pressure (TMP) jump. The change in cake layer structure might bear more responsibility for the TMP jump than the quantity of cake layer.     

Sustainable Flux Fouling in a Membrane Bioreactor: Impact of Flux and MLSS

Abstract

The long term sustainable flux behavior of a submerged membrane bioreactor operated under a steady state conditions at a range of mixed liquor suspended solids (MLSS) concentrations has been examined. Comparison of fouling rates at a number of imposed fluxes has been made between long term filtration trials and short term tests using the flux step method. Results indicate an exponential relationship between fouling rate and flux for both long and short term trials, although the value was an order of magnitude lower during long term tests. Moreover, operation during long term trials is characterised by a period of pseudo stable operation followed by a catastrophic rise in TMP at a given critical filtration time (t_filt) during trials at 6 g · L^?1. This time of stable operation, t_filt, is characterised by a linear relationship between fouling rate and flux. Results have been compared with the literature. Data for membrane fouling prior to the end of t_filt yielded a poor fit with a recently proposed model. Trends recorded at t>t_filt revealed the fouling rate to follow no definable trend with flux, contrary to the notion that fouling beyond the critical filtration time relates to solids deposition.     

活性炭提高膜生物反应器运行性能的研究进展

通过投加粉末活性炭(PAC)/颗粒活性炭(GAC)改善污泥混合液性质从而减缓膜污染是膜生物反应器(MBR)领域的研究热点,重点介绍了最近五年有关活性炭与MBR结合处理不同类型废水的研究进展,投加PAC/GAC对MBR处理能力的影响,对减缓膜污染的作用,尤其是结合动态膜(DM)论述对污泥性质的改善.重点讨论了活性炭在好氧...     

膜生物反应器中膜的清洗研究

对膜生物反应器处理柠檬酸酸洗废水中膜的清洗进行了研究，通过不同的清洗方法对膜通量的恢复程度进行评价。确定了反冲洗时间及反冲洗周期，经过试验研究与分析，在反冲洗的同时结合正洗的清洗方法，效果好于单纯的反冲洗方法；确定了化学清洗剂种类、清洗剂的用量以及化学清洗周期。采用物理清洗与化学清洗相结合的方法，清洗效果很好。保证了MBR的稳定运行。     

钙离子对MBR污泥混合液及膜污染层影响研究进展

膜生物反应器(membrane bioreactor,MBR)作为一种新型的污水处理技术,以其高效、实用等特点备受人们的关注.然而,膜污染导致膜通量的下降,增加膜组件更换和清洗的频率,使其成为了影响MBR广泛应用的最大的障碍.本文首先探讨了钙离子对污泥絮体生物絮凝行为的强化机制,进而阐述了钙离子对活性污泥关键指标的影响;归纳总结了钙离子对膜污染影响的最新研究进展,最后对该领域的研究进行了展望.     

溶解氧对一体式膜生物反应器(IMBR)的影响

针对溶解氧(DO)和气水比对IMBR工艺出水效果的影响及能耗问题,从气水比对DO的影响和DO对COD与NH3-N去除效果的影响着手,探讨研究气水比、溶解氧以及污水处理效果之间的最佳工作点。试验结果表明,在ρ(MLSS)分别为4.23,4.09,3.70g/L的运行条件下,MBR的最佳运行气水比相应为35∶1,25∶1,17∶1;溶解氧变化速率随污泥浓度的下降而升高;DO的变化对COD的去除效果并不显著;在高污泥浓度下,DO的质量浓度保持在2.63～4.85mg/L之间时,氨氮的去除率随溶解氧浓度的上升而下降,氨氮去除率达90%以上;但DO浓度过低时,氨氮去除效果不佳。     

Experimental Study and Design of a Submerged Membrane Distillation Bioreactor

A hybrid process incorporating membrane distillation in a submerged membrane bioreactor operated at elevated temperature is developed and experimentally demonstrated in this article. Since organic particles are rejected by an ‘evaporation’ mechanism, the retention time of non‐volatile soluble and small organics in the submerged membrane distillation bioreactor (MDBR) is independent of the hydraulic retention time (mainly water and volatiles). A high permeate quality can be obtained in the one‐step compact process. The submerged MD modules were designed for both flat‐sheet membranes and tubular membrane configurations. The process performance was preliminarily evaluated by the permeate flux stabilities. The module configuration design and air sparging used in the MDBR process were tested. Flux declines were observed for the thin flat‐sheet hydrophobic membranes. Tubular membrane modules provided more stable permeate fluxes probably due to the turbulent condition generated from air sparging injected inside the tubular membrane bundles. The experiments with the submerged tubular MD module gave stable fluxes of approximately 5 L/m² h over 2 weeks at a bioreactor temperature of 56 °C. The total organic carbon in the permeate was consistently lower than 0.7 mg/L for all experiments.     

Effect of Sludge Retention Time on Membrane Bio‐Fouling Intensity in a Submerged Membrane Bioreactor

Abstract

The submerged membrane bioreactor (sMBR) is being increasingly applied for municipal and industrial wastewater treatment. This paper examines the role of sludge retention time (SRT), an important operating parameter of the MBR as it affects the biological characteristics of the sludge and therefore influences membrane fouling. Well controlled runs were carried out at short SRT (10days) and moderate SRT (30days) in a 30 L submerged MBR equipped with KUBOTA flat‐sheet membranes. At steady operation, the mixed liquor suspended solids (MLSS) stabilized at approximately 5–6 g/L and 8.5–10 g/L for SRT 10 and 30days respectively. The DGGE profiles suggested a shift in the dominant bacterial community with the prolonged SRT. The soluble microbial products (SMP) were 9.3 mg/L and 5.4 mg/L at the SRTs of 10days and 30days respectively. The total amount of extracellular polymeric substance (EPS) extracted from the floc and the supernatant was approximately constant at the two SRTs under the same organic loading rate. However, the polysaccharide concentration in the supernatant was about 100% higher for the SRT of 10days than that for 30days. The viscosity of the biomass increased with the prolonged SRT, while the estimated average air induced water velocity was similar for the two SRTs. The results of flux stepping tests showed that the membrane fouling rate (dTMP/dt) at SRT 10days was always higher than that at 30days at each flux step. Similarly, long term experimental runs at a constant flux of 20 L/m²·h clearly showed more severe membrane fouling for the SRT of 10days than that at 30days. This implies that fouling is more influenced by the concentration of SMP and Polysaccharides than the MLSS.     

A novel combination of methane fermentation and MBR — Kubota Submerged Anaerobic Membrane Bioreactor process

Methane fermentation is considered one of the best placed biological processes to reduce volume of organic waste while keeping small sludge production and recovering energy. One of the disadvantages of early anaerobic digestion technologies was the long hydraulic retention time thus large capacity tanks were required to hold slow growing methanogenic bacteria. New technological attempts such as upflow anaerobic sludge blanket (UASB), fixed or fluidised bed and membrane bioreactor (MBR) appeared as countermeasures.Kubota’s submerged anaerobic membrane biological reactor (KSAMBR) process has been developed in the last decade and successfully applied in a number of full-scale food and beverage industries. It consists of a solubilization tank and a thermophilic digestion tank, the latter incorporating submerged membranes. The biogas generated can be utilized for water heating via boilers. Both permeate and waste anaerobic sludge are further treated in wastewater treatment facilities.One of the main advantages of KSAMBR is that membranes retain the methanogenic bacteria while dissolved methane fermentation inhibitors such as ammonia are filtered out with the permeate. This makes the KSAMBR process very stable. Furthermore, the digester volumes can be scaled down to 1/3 to 1/5 of the conventional digesters provided that biomass is 3 to 5 times as concentrated.Applications include stillage treatment plants for Shouchu (Japanese spirits made from sweet potato, rice or other grains), potato processing sites, sludge liquor and food factory treatment plants.In summary, it is believed that KSAMBR offers the best possible solution combining the benefits of methane fermentation process with the performance of membrane technology. More details will be presented in the proceedings paper and in the presentation.     

污泥龄对膜生物反应器中溶解性荧光物质特性的影响

采用三维荧光(EEM)光谱技术分析了膜-生物反应器(MBR)处理餐饮废水过程中的各种溶解性有机物(DOM),并对比研究不同污泥龄(SRT)条件下DOM的EEM光谱的迁移变化特性。结果表明各种DOM的荧光物质中,普遍存在以色氨酸为代表的蛋白质类物质,且溶解性膜污染中只有高、低激发波长色氨酸,表明蛋白质类物质是导致膜污染的重要因素。腐殖酸溯源又表明进水及出水DOM中的腐殖酸以微生物代谢产生的带有荧光基团的腐殖酸类为主。     

溶解性有机质对土壤中有机污染物迁移转化的影响因素

溶解性有机质(DOM)对土壤中有机物的迁移转化有重要作用,也受众多因素影响。介绍了DOM的基本概念、分类和环境作用;讨论了DOM的来源、DOM的分子量大小、DOM的浓度和p H值等影响因素对DOM与有机物的作用并分析了原因;提出了研究的走向。     

高温催化氧化法测定土壤中溶解性有机碳

采用高温催化氧化法测定了岩溶区土壤中溶解性有机碳（DOC）,研究了提取过程中的相关参数对DOC测定的影响。首先用超纯水对新鲜采集的土壤样品进行振荡提取5 h,快速离心20 min后采用孔径为0.45μm的微孔滤膜对提取液进行抽滤,最后用Multi 3100 N/C多功能分析仪测定了提取液中的含碳量。