Competitive Metal Ion Binding to a Silicate-Immobilized Datura innoxia Biomaterial

Abstract

Metal ion binding with a flowing system to a biosorbent comprised of cultured cell-wall fragment within a polysilicate matrix has been investigated. Solutions containing 0.10 mM Pb²⁺, Cu²⁺, Ni²⁺, Cd²⁺, and Zn²⁺ were exposed to the material in combinations of two, three, and five metals while simultaneously monitoring the concentration of all metals in the effluent stream. A relative affinity order of Pb²⁺ > Cu²⁺ >> Zn²⁺ ≈ Cd²⁺ > Ni²⁺ was determined when all five metal ions were exposed to the material. Lower-affinity metal ions were exposed to the material sequentially. Both metal-specific and common binding sites were observed for each metal ion. The presence of both binding sites that are common to all metal ions investigated and sites that appear to be unique for each metal ion could significantly impact the utility of single-metal ion studies on the application of such biosorbents for the selective removal of metal ions from natural water.     

Electron Beam Grafted Polymer Adsorbent for Removal of Heavy Metal Ion from Aqueous Solution

Abstract

An electron beam grafted adsorbent was synthesized by post irradiation grafting of acrylonitrile (AN) on to a non‐woven thermally bonded polypropylene (PP) sheet using 2 MeV electron beam accelerator. The grafted poly(acrylonitrile) chains were chemically modified to convert a nitrile group to an amidoxime (AMO) group, a chelating group responsible for metal ion uptake from an aqueous solution. The effect of various experimental variables viz. dose, dose rate, temperature, and solvent composition on the grafting extent was investigated. PP grafted with the amidoxime group (AMO‐g‐PP) was tested for its suitability as an adsorbent for removal of heavy metal ions such as Co²⁺, Ni²⁺, Mn²⁺, and Cd²⁺ from aqueous solution. Langmuir and Freundlich adsorption models were used to investigate the type of adsorption of these ions. The adsorption capacities of the adsorbent for the metal ions were found to follow the order Cd²⁺>Co²⁺>Ni²⁺>Mn²⁺. The kinetics of adsorption of these ions indicated that the rate of adsorption of Cd²⁺ was faster than that of other ions studied.     

Removal of Metal Contaminants by Ion‐Exchange Resin Columns,Thala Valley Tip,Casey Station,Antarctica

Abstract

Salinity and low temperature effects on adsorption of contaminant metals from water using an iminodiacetic acid (IDA) ion‐exchange resin, were investigated under dynamic flow conditions. The order of selectivity of the resin (20°C and 0% seawater) was: Cu²⁺> Pb²⁺> Cr³⁺> Ni²⁺>Cd²⁺>Zn²⁺. Low temperature (4°C) had no significant effect on the selectivity of the contaminant metals and salinity only affected selectivity for Cr³⁺ and Cu²⁺. Copper had highest selectivity in all column experiments, except where extensive deprotonation occured. Buffering affected retention of Cr³⁺; possibly due to precipitation or complexation as a result of increase in pH.     

Selective Transport of Copper(I,II), Cadmium(II), and Zinc(II) Ions through a Supported Liquid Membrane Containing Bathocuproine,Neocuproine, or Bathophenanthroline

Abstract

Some selective transport systems for heavy metallic ions through a supported liquid membrane (SLM) containing a 2,2′-dipyridyl derivative ligand, 4,7-diphenyl-2,9-dimethyl-1,10-phenanthroline (bathocuproine), 2,9-dimethyl-1,10-phenanthro-line (neocuproine), or 4,7-diphenyl-1,10-phenanthroline (bathophenanthroline), were investigated. The transport of copper(I, II), cadmium(II), zinc(II), lead(II), and cobalt(II) ions was accomplished with a halogen ion such as chloride, bromide, or iodide ion as a pairing ion species for any SLM. The ranking of the permeability of the metallic ions was Cu^+,2+, Zn²⁺, Cd²⁺ ? Pb²⁺, Co²⁺. When the oxidation-reduction potential gradient was used as a driving force for metallic ions, the transport of Cu⁺ ion was higher than those of Cd²⁺ and Zn²⁺ ions for any SLM containing bathocuproine, neocuproine, or bathophenanthroline. On the other hand, in the transport system which used the concentration gradient of pairing ion species, the permeability of the Cu²⁺ ion decreased whereas that of the Cd²⁺ ion increased. Moreover, it was found that the different selectivity for the transport of metallic ions is produced by using various pairing ion species.     

Concentration and separation of metallic ions from aqueous solutions by using EC-PEG 4000 alloy membranes

The concentration and separation of some metallic ions have been achieved by complexing these species with suitable macromolecules or with water-soluble polymers in ultrafiltration. The effect of water-soluble poly(vinyl alcohol) (PVA) on the concentration and separation of Cu²⁺, Ni²⁺, and Fe³⁺ ions have been investigated by using EC-PEG4000 alloy membranes in ultrafiltration experiments. The water permeability of the membranes has been measured at various pressures. The permeability of these membranes for metal ions, however, has been recorded at constant pressure but at different pH values. The highest water-permeable membrane is also permeable for Cu²⁺ and Ni²⁺, but it shows a considerable retention for Fe³⁺, probably as a result of the hydrolysis of Fe³⁺. The retentions of metallic ions and metallic ion-PVA couples have been determined at constant pressure but varying pH and polymer concentration values. It has been shown that Fe³⁺/Ni²⁺ pairs can well be separated by using PVA. © 1993 John Wiley & Sons, Inc.     

Chelating polymer bearing triazolylazophenol moiety as the functional group

The chelating polymer-bearing triazolylazophenol moiety as the functional group was synthesized, its metal adsorption properties for 6 divalent heavy metal ions; Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, and Pb²⁺ were investigated. The capacity of the polymer for Cu²⁺ achieved 8.7 mEq/g in pH 5.3 solution. The polymer showed remarkable color changes from orange to red violet or blue violet with its chelations to the heavy metal ions. The metal adsorption rates of the polymer were rapid in performing complete capacity saturation of heavy metal ions in about 30 min. The capacities varied little the presence of alkali or alkaline earth metal ions in solutions. The perfect elimination of metals from the polymer–M²⁺ chelates were performed with mineral acid solutions. The metal ions; Cu²⁺ and Ni²⁺ in plating-process solutions were effectively removed by the chelating polymer, and the polymer can be practically used for the removal of these ions from waste water.     

Chelation ion‐exchange properties of copolymer resin derived from 4‐hydroxyacetophenone,oxamide, and formaldehyde

A copolymer (4‐HAOF) prepared by condensation of 4‐hydroxyacetophenone and oxamide with formaldehyde in the presence of an acid catalyst proved to be a selective chelating ion‐exchange copolymer for certain metals. Chelating ion‐exchange properties of this copolymer were studied for Fe³⁺, Cu²⁺, Ni²⁺, Co²⁺, Zn²⁺, Cd²⁺, Pb²⁺, and Hg²⁺ ions. A batch equilibrium method was employed in the study of the selectivity of metal‐ion uptake involving the measurements of the distribution of a given metal ion between the copolymer sample and a solution containing the metal ion. The study was carried out over a wide pH range and in media of various ionic strengths. The copolymer showed a higher selectivity for Fe³⁺ ions than for Co²⁺, Zn²⁺, Cd²⁺, Pb²⁺, Cu²⁺, Ni²⁺, and Hg²⁺ ions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 787–790, 2003     

Concentration and separation of aqueous solutions of Cu2+, Ni2+, Fe3+ by dextran

The effects of water-soluble polymers on the concentration and separation of the aqueous solutions of the metal ions have been studied. The separation of metal ions can be possible by ultrafiltration-complexation process. The effect of Dextran, which is a water-soluble polymer, on the concentration and separation of metal ions (Cu²⁺, Ni²⁺, Fe³⁺) have been investigated by using EC-PEG 4000 alloy membranes. The permeability of these membranes for metal ions has been rrecorded at constant pressure but different pH values. It has been notices that the highest water-permeable membrane is also permeable towards Cu²⁺ and Ni²⁺, but has shown a considerable retention for Fe³⁺ as a result of the hydrolysis of Fe³⁺. The retentions of metallic ions and metallic-ion-Dextran couples have been determined at constant pressure but different pH and polymer concentration values. It has been shown that Fe³⁺/Ni²⁺ and Fe³⁺/Cu²⁺ couples can be separated by using Dextran. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(hydroxamic acid) chelating resin from poly(methyl acrylate)‐grafted sago starch

A new chelating ion‐exchange resin containing the hydroxamic acid functional group was synthesized from poly(methyl acrylate) (PMA)‐grafted sago starch. The PMA grafted copolymer was obtained by a free‐radical initiating process in which ceric ammonium nitrate was used as an initiator. Conversion of the ester groups of the PMA‐grafted copolymer into hydroxamic acid was carried out by treatment of an ester with hydroxylamine in an alkaline solution. The characterization of the poly(hydroxamic acid) chelating resin was performed by FTIR spectroscopy, TG, and DSC analyses. The hydroxamic acid functional group was identified by infrared spectroscopy. The chelating behavior of the prepared resin toward some metal ions was investigated using a batch technique. The binding capacities of copper, iron, chromium, and nickel were excellent and the copper capacity was maximum (3.46 mmol g⁻¹) at pH 6. The rate of exchange of the copper ion was very fast that is, t_1/2 < 5 min. It was also observed that the metal ion‐sorption capacities of the resin were pH‐dependent and its selectivity toward the metal ions used is in the following order: Cu²⁺ > Fe³⁺ > Cr³⁺ > Ni²⁺ > Co²⁺ > Zn²⁺ > Cd²⁺ > As³⁺ > Pb²⁺. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1256–1264, 2001     

Application of insoluble cellulose xanthate for the removal of heavy metals from aqueous solution

Insoluble cellulose xanthate (ICX), O-alkyl dithiocarbonate of cellulose, was synthesized and used for the removal of heavy metal ions from aqueous solutions. ICX possessed carbon disulfide (CS₂) as a functional group, which was obtained by esterification of the hydroxyl group on cellulose polymer matrix with CS₂. CS₂ could form complexes with divalent transition metal ions, and the resulting ICX-metal complex was water-insoluble and settled easily. The optimum composition for ICX synthesis was cellulose/NaOH/CS₂=1: 2: 2.3 in mole base, which showed the highest removal capacity. The selectivity and binding capacity of ICX for heavy metals were in the order of Pb²⁺> Cd²⁺> Ni²⁺ and Cd²⁺> Pb²⁺> Ni²⁺, respectively. More than 90 % of the initial amount of heavy metals was removed within 30 min. The optimum pH was neutral or slightly alkaline, and more than 40 % of initial heavy metals was removed even in the acidic range of pH 2 to 3.     

Use of super absorbent hydrogels derivative from acrylamide with itaconic acid and itaconates to remove metal ions from aqueous solutions

Poly(acrylamide-co-itaconic acid) (AAm/IA) and poly(acrylamide-co-monomethoxyethyl itaconate) (AAm/MEI) hydrogels (HGs) synthesized at different molar ratios were used to study the adsorption of some metal ions as Cu²⁺, Ni²⁺, Pb²⁺, Cd²⁺, and Fe³⁺ in aqueous solutions at different concentration: 10, 50, 100, 500, and 1000 mg L⁻¹. Statistical analysis was performed and the effect of the metal ion, ion concentration, and hydrogel (HG) composition, on adsorption and adsorption efficiency, was evaluated for both HGs studied (AAm/IA and AAm/MEI) and each factor gave rise to significant differences (P ≤ 0.05). The adsorption depends on the type of ion, its concentration, and also influenced by the type and composition of the HGs. For each system the adsorption efficiencies for all ions were similar with exception of Fe³⁺, which showed the highest adsorption efficiency in AAm/MEI HG, but the less for the AAm/IA. For both systems, the maximum adsorption efficiency was observed when the molar ratio AAm/IA or AAm/MEI is 80/20. When the adsorption was carried out with individual ions, AAm/MEI HG was more efficient than AAm/IA. For a multielement sample of Cu²⁺, Ni²⁺, Pb²⁺, and Cd²⁺, both HGs could adsorb all the ions and their behavioral trend was the same in both cases, in which the adsorption efficiency was Pb²⁺ > Cu²⁺ > Cd²⁺ > Ni²⁺. The results of the statistical analysis evidence the advantage of its use in this type of studies. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46999     

Synthesis,characterization, metal sorption,and biological activity of poly(N‐heterocylic acrylamide)

N‐heterocyclic acrylamide monomers were prepared and then transferred to the corresponding polymers to be used as an efficient chelating agent. Polymers reacted with metal nitrate salts (Cu²⁺, Pb²⁺_, Mg²⁺, Cd²⁺, Ni²⁺, Co²⁺_, Fe²⁺) at 150°C to give metal‐polymer complexes. The selectivity of the metal ions using prepared polymers from an aqueous mixture containing different metal ion sreflected that the polymer having thiazolyl moiety more selective than that containing imidazolyl or pyridinyl moieties. Ion selectivity of poly[N‐(benzo[d]thiazol‐2‐yl)acrylamide] showed higher selectivity to many ions e.g. Fe³⁺, Pb²⁺, Cd²⁺, Ni²⁺, and Cu²⁺. While, that of poly[N‐(pyridin‐4‐yl)acrylamide] is found to be high selective to Fe³⁺ and Cu²⁺ only. Energy dispersive spectroscopy measurements, morphology of the polymers and their metallopolymer complexes, thermal analysis and antimicrobial activity were studied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42712.     

Removal characteristics of metal cations and their mixtures using micellar-enhanced ultrafiltration

Divalent ions were removed by ultrafiltration of anionic surfactant solution and the removal characteristics in single and mixed systems were investigated. The removal efficiency was >95% when the ratio of sodium dodecyl sulfate (SDS) to metal ions (S/M ratio) was >10. In single metal systems, the removal efficiency of each metal ion was almost the same. In the mixture, however, there was slight difference (ca. 1–2%) of removal efficiency and the order was Cd²⁺>Cu²⁺>Co²⁺≈Zn²⁺. As S/M ratio increased, the difference in removal efficiency diminished. To explain the difference of removal efficiency in a mixture, complexation of divalent metal ion with counterion was considered. The distribution of complexed form of each metal ion was calculated, but it did not coincide with the experimental results. Further research will be necessary for a clear explanation.     

Binding of heavy metal ions by formaldehyde-polymerized peanut skins

Peanut skin, when treated with formaldehyde to polymerize tannins, is a highly efficient substrate for removal of many heavy metal ions from aqueous waste solutions. The ions Ag¹⁺, Cd²⁺, Cr⁶⁺, Cu²⁺, Hg²⁺, Ni²⁺, Pb²⁺, Zn²⁺, as well as Ca²⁺ and Mg²⁺, were contacted with formaldehyde-treated peanut skin. Quantitative removal could be achieved with Ag¹⁺, Cd²⁺, Cu²⁺, Hg²⁺, Pb²⁺, and Zn²⁺. Capacity of the substrate for ions was promising for Pb²⁺ (2.1 meq/g substrate), Cu²⁺ (3.0 meq/g), and Cd²⁺ (1.3 meq/g). Sorption from a solution containing Cd²⁺, Cu²⁺, Hg²⁺, Ni²⁺, Pb²⁺, Zn²⁺, on a packed column of formaldehyde-treated peanut skin indicated that Hg²⁺, Pb²⁺, and Cu²⁺ were rapidly and completely bound to the packing, while Cd²⁺, Ni²⁺, and Zn²⁺ were poorly bound until the preferred ions had been removed from solution.     

Selective online solid-phase extraction of copper using p-morpholino-methylcalix[4]arene appended silica-based column

ABSTRACT

This study deals with investigation of selectivity of p-morpholino-methylcalix[4]arene appended silica from a group of metal ions having similar charge and radii. The values of distribution ratio revealed that modified silica possess higher selectivity for Cu²⁺. In addition, relative selectivity coefficients of modified silica were found to be 24.1, 13.8, 8.6 and 4.01 for Cu²⁺/Ni²⁺, Cu²⁺/Co²⁺, Cu²⁺/Cd²⁺, Cu²⁺/Pb²⁺, respectively. The maximum adsorption capacity was 1.5 mmolg^?1. The reusability data suggested no any loss of adsorption capacity of this material up to 10 cycles. The developed material was also applied for determination of copper in lake water samples with satisfactory results.     

Utilization of some starch derivatives in heavy metal ions removal

Three types of starch derivatives containing amide groups were used in removal of heavy metal ions from their solutions. These starch derivatives were poly(acrylamide)–starch graft copolymer, carbamoylethylated starch, and starch carbamate. The different factors affecting metal ion adsorption on these substrates, such as pH, metal ion concentration, type of starch derivatives, treatment time, and temperature, were studied. Results obtained indicate that the poly(acrylamide)–starch graft copolymer was a selective adsorbant for Hg²⁺ at pH 0.5–1. The adsorption values ofdifferent metal ions on these starch derivatives follow the order of Hg²⁺ > Cu²⁺ > Zn²⁺ > Ni²⁺ > Co²⁺ > Cd²⁺ > Pb²⁺. The adsorption values depend upon pH, type of starch derivative, treatment duration, and temperature. The adsorption efficiency percentage of metal ions on the three substrates follows the order of carbamoylethylated starch > poly(acrylamide) − starch graft copolymer > starch carbamate. © 1998 John Wiley & Sons, Inc. J Appl Polm Sci 69: 45–50, 1998     

Studies of selective adsorption resins. XXV. Preparation of macroreticular chelating resins containing aminomethylphosphonic acid groups from methyl methacrylate/divinylbenzene copolymer beads and their adsorption capacity

Macroreticular chelating resins containing aminomethylphosphonic acid groups were prepared by reaction of methyl methacrylate/divinylbenzene copolymer beads with triethylenetetramine, followed by the reaction of the products with phosphorous acid and formaline. The adsorption capacities of this resin for Cu²⁺, Pb²⁺, Zn²⁺, Ni²⁺, Co²⁺, Ca²⁺, and Mg²⁺ were determined at various pH values. The order of chelate stability for the resin was Cu²⁺ > Pb²⁺ > Zn²⁺ > Ni²⁺ > Co²⁺ > Ca²⁺ > Mg²⁺. Copper, nickel, zinc, calcium, and magnesium ions can be eluted with 1 mol dm^?3 hydrochloric acid. The proposed resin appears to be useful for the removal of Ca²⁺ and Mg²⁺ from salt solution.     

SORPTION PROCESSES OF NATURAL IRANIAN BENTONITE EXCHANGED WITH CD2+, CU2+, NI2+, AND PB2+ CATIONS

Experimental studies on the retention of cadmium (Cd²⁺), copper (Cu²⁺), nickel (Ni²⁺), and lead (Pb²⁺) by bentonite samples from Iran were conducted using single- and multiple-component solutions. Based on the sorption capacity of bentonite the following order was obtained for single- and multiple-component solutions: Pb²⁺ > Cd²⁺ > Ni²⁺ > Cu²⁺. The maximum adsorption capacities of bentonite with metals in single- and multiple-component solutions were 29.5%, 22.5%, 19.2%, and 17.1% and 13.5%, 13.4%, 12.1%, and 9.1% for Pb²⁺, Cd²⁺, Ni²⁺, and Cu²⁺, respectively. Desorption isotherms of Cd²⁺, Cu²⁺, Ni²⁺, and Pb²⁺ deviated significantly from the sorption isotherms, thereby indicating irreversible or very slowly reversible sorption. Finally, soil solution saturation indices and metal speciation were assessed using the Visual MINTEQ 2.6 program and the probability of mineral precipitation was supported by scanning electron microscopy.     

Selective Extraction of Cu2+ and Ag+ Ions from Sulfuric Acid by Synergistic Combinations of Tetradentate Thia Macrocycles with Dioodecylnaphthalene Sulfonic Acid

Abstract

The aqueous-insoluble thia macrocycles tetrathia-14-crown-4 (TT14C4) and tetrathia-16-crown-4 (TT16C4) strongly and selectively synergize the extraction of Cu²⁺ and Ag⁺ ions from aqueous sulfuric acid solutions by the organophilic cation exchanger didodecylnaphthalene sulfonlc acid (HDDNS) in toluene diluent. Over a range of sulfuric acid concentrations, the selectivity is given by the order Ag² > Cu²⁺ > Mn²⁺, Fe²⁺, Fe³⁺, Co²⁺, Ni²⁺, and Zn²⁺, where synergism occurs only for Ag⁺ and Cu²⁺. Selectivity factors greater than 300 have been achieved for Cu²⁺ over ubiquitous Fe³⁺. The synergistic extraction of Cu²⁺ and Ag⁺ was explored as a function of sulfuric acid concentration, relative concentration of macrocycle vs. HDDNS, and loading.     

Synthesis and adsorption properties,toward some heavy metal ions,of a new polystyrene‐based terpyridine polymer

A novel polymeric ligand having 2,2′:6′,2″‐terpyridine as pendant group was prepared through a Williamson type etherification approach for the reaction between 4′‐hydroxy‐2,2′: 6′,2″‐terpyridine and the commercially available 4‐chloromethyl polystyrene. The chelating properties of the new polymer toward the divalent metal ions (Cu²⁺, Zn²⁺, Ni²⁺, and Pb²⁺) in aqueous solutions was studied by a batch equilibration technique as a function of contact time, pH, mass of resin, and concentration of metal ions. The amount of metal‐ion uptake of the polymer was determined by using atomic absorption spectrometry. Results of the study revealed that the resin exhibited higher capacities and a more pronounced adsorption toward Pb²⁺ and that the metal‐ion uptake follows the order: Pb²⁺ > Cu²⁺ > Zn²⁺ > Ni²⁺. The adsorption and binding capacity of the resin toward the various metal ions investigated are discussed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012