离心萃取器提取对甲酚的实验和模拟研究

In this study, extraction of p-cresol from the simulated wastewater has been studied using centrifugal extractors and QH-1 extractant. The distribution ratio of p-cresol was approximately 308.5 in the QH-1-p-cresol （pH =2.0） system. The extraction stage efficiency of the single-stage centrifugal extractor was higher than 92%, and the extraction rate of the three-stage cascade was higher than 99%. When 15% NaOH was used for the stripping of p-cresol in QH-1 solution, the stripping rate of the three-stage cascade reached 100%. A mathematical model of multistage countercurrent extraction process that considers the phase volume change, extraction stage efficiency, and phase entrainment was used to simulate the extraction of p-cresol using centrifugal extractors. The calculated results using this model were in good agreement with the experimental results.     

Equilibrium of liquid-liquid extraction of 2-phenylbutyric acid enantiomers: Experiment and model

The utilization of liquid–liquid extraction for the separation of 2-phenylbutyric acid(2-PBA) enantiomers was proposed. Factors affecting the extract process were investigated, including organic solvents, β-cyclodextrin derivatives, cyclodextrin concentration, p H and temperature. A model was proposed to describe the separation process based on the homogeneous phase reaction mechanism. Important parameters of this model were determined experimentally. The physical distribution coefficients for molecular and ionic 2-PBA were0.129 and 7.455, respectively. The equilibrium constants of the complexation reactions were 89.36 and36.78 L·mol~(-1) for(+)-and(-)-2-PBA, respectively. The model was verified by experiments and proved to be an excellent means to optimize the separation system. Through modeling prediction and experiment, the best conditions(e.g., pH value of 3.00, extractant concentration of 0.1 mol·L~(-1), temperature of 5.0 °C) were acquired. Under this condition, the maximum enantioselectivity(2.096) was obtained.     

水性氯化物介质中对甲基苯烷基硫醚萃取钯的研究

p-Methylphenylalkylsulfide of various alkyl chain length as extractant were synthesized and the extraction of palladium was examined in terms of equilibrium and kinetics. Distribution ratio of Pd was independent of alkyl chain length. For aqueous chloride media, there was a significant difference in distribution ratios for the solution of NaC1 and HC1. The results of loading test and the slope analysis suggest that the extractant and Pd (Ⅱ) form 2:1 complex. Furthermore, the extraction rate based on the volume of aqueous phase was obtained in a stirred vessel, and the rate equation was presented. Unfortunately, it was difficult to construct surfactant liquid membrane system by use of the present extractant.     

Optimization of coproduction of ethyl acetate and n-butyl acetate by reactive distillation☆

Based on a previous investigation, a simulation model was used for optimization of coproduction of ethyl acetate and n-butyl acetate by reactive distil ation. An experimental setup was established to verify the simulated results. The effects of various operating variables, such as ethanol feed location, acetic acid feed location, feed stage of reaction mixture of acetic acid and n-butanol, reflux ratio of ethyl acetate reactive distillation column, and distil-late to feed ratio of n-butyl acetate column, on the ethanol/n-butanol conversions, ethyl acetate/n-butyl acetate purity, and energy consumption were investigated. The optimal results in the simulation study are as follows:ethanol feed location, 15th stage;acetic acid feed location, eighth stage;feed location of reaction mixture of acetic acid and n-butanol, eighth stage;reflux ratio of ethyl acetate reactive distillation column, 2.0;and distillate to feed ratio of n-butyl acetate, 0.6.     

Study on liquid–liquid two-phase mass transfer characteristics in the microchannel with deformed insert

In this work, the liquid–liquid two-phase mass transfer characteristics in the microchannel with deformed insert were studied. The experiment used di-(2-ethylhexyl) phosphoric acid/kerosene-Cu²⁺as the mass transfer evaluation system. The effects of some key factors such as the total flow velocity,channel inner diameter, channel length, insert diameter, extractant concentration on the extraction efficiency and mass transfer coefficient were systematically investigated. Compared with a ...     

Direct extraction of Mo(Ⅵ) from sulfate solution by synergistic extractants in the rotation column

Direct extraction of molybdenum from sulfate solution with synergistic extractants(mixture of D_2EHPA and TBP)was studied in the rotation column. The influence of extractant concentration and initial pH of aqueous phase was studied in the bench scale experiments. The outcomes demonstrated that the synergistic solvent extraction enhances the constancy of the extracted complexes for transfer into the organic phase. In the continuous experiments, the effect of different operating parameters such as speed of agitation, inlet solvent flow rate and inlet aqueous flow rate on the holdup, mean drop size, drop size distribution, slip and characteristic velocities and extraction percentage were examined. Modified correlations were proposed for prediction of hydrodynamic parameters with consideration of reaction extraction condition in the rotation column. Furthermore, these correlations were compared with the experimental data. According to the results, the direct extraction of Mo(Ⅵ) from aqueous solution and sulfuric media with extraction efficiency of 90.4% was obtained at higher rotor speed(240 r·min~(–1) rpm) in this column.     

采用不同载体的中空纤维更新液膜Cu(Ⅱ)传质的研究(英文)

The extraction ability of organophosphorus extractant D2EHPA (di-2-ethylhexyl phosphoric acid) and hydroximic extractant Lix984N are investigated by the extraction equilibrium experiments. Effects of carrier concentration and organic/aqueous volume ratio on the mass transfer of hollow fiber renewal liquid membrane (HFRLM) are studied. Results show that, in the extracting process, kerosene and n-heptane are more suitable than methyl-isobutyl ketone, butylacetate and benzene as the diluents of D2EHPA or Lix984N. The favorable feed pH is 4.4 for D2EHPA and 2.6 for Lix984N. The mass transfer flux of HFRLM increases with carrier concentration and finally reaches a plateau. The mass transfer flux and the overall transfer coefficient increase with the or-ganic/aqueous volume ratio, reach the maximum and then decrease.     

Enantioseparation of 3-chlorophenylglycine enantiomers using Mandyphos-Pd as chiral extractant

Chiral extractant plays a key role in chiral extraction, and considerable efforts have been undertaken for the development of new and efficient chiral extractants in recent years. This work demonstrated for the first time that chiral ferrocenyl diphosphine ligand(Mandyphos-Pd) had considerable ability to enantioseparate 3-Chlorophenylglycine enantiomers with separation factor(α) of 2.64. Mandyphos-Pd concentration and p H had significant influences on enantioselectivity, while operating temperature showed less influence. The extraction experiments can be performed at room temperature(20 °C) which had the advantage of energy saving. After optimization, the highest performance factor(pf, 0.08376) was obtained at the condition of p H 7.8 and Mandyphos-Pd concentration 1.2 mmol·L~(-1). According to the experimental results, the possible recognition mechanism was discussed.     

稀释剂对三烷基氧膦萃取草酸的影响

In liquid-liquid solvent extraction processes, diluents have a strong influence on the extraction mechanism and efficiency. In this study, benzene, cyclohexane, trichloromethane, carbon tetrachloride, methyl isobutyl ketone (MIBK), butyl acetate, and 1-octanol were used as diluents in the extraction of oxalic acid by trialkylphos-phine oxide (TRPO). The effects of extractant concentration, initial concentration of oxalic acid and diluent type on the extraction equilibrium partition coefficient are analyzed. The sequence of the extraction ability by different diluents is MIBK > butyl acetate > cyclohexane=benzene > carbon tetrachloride > 1-octanol > trichloromethane. Extraction mechanism was analyzed and extraction model parameters were evaluated.     

Desulfurization of liquid hydrocarbon fuels via Cu_2O catalyzed photooxidation coupled with liquid–liquid extraction

By combining the photochemical reaction and liquid–liquid extraction(PODS), we studied desulfurization of model fuel and FCC gasoline. The effects of air flow, illumination time, extractants, volume ratios of extractant/fuel, and catalyst amounts on the desulfurization process of PODS were analyzed in detail. Under the conditions with the air as oxidant(150 ml·min~(-1)), the mixture of DMF–water as extractant(the volume ratio of extractant/oil of 0.5) and photo-irradiation time of 2 h, the sulfur removal rate reached only 42.63% and 39.54% for the model and FCC gasoline, respectively. Under the same conditions, the sulfur removal rate increased significantly up to79% for gasoline in the presence of Cu_2O catalyst(2 g·L~(-1)). The results suggest that the PODS combined with a Cu_2O catalyst seems to be a promising alternative for sulfur removal of gasoline.     

咪唑类离子液体对木质纤维预水解液的脱毒

针对燃料乙醇生物炼制过程中抑制物对酵母乙醇发酵的抑制作用,以水洗稀酸蒸汽爆破预处理玉米秸秆得到的预水解液为研究对象,采用新型绿色脱毒技术--离子液体进行萃取脱毒,研究比较了两种咪唑类离子液体[烷基咪唑六氟磷酸盐离子液体[C_nmim][PF₆](n 4,6,8)和烷基咪唑四氟硼酸盐离子液体[C_nmim][BF₄](n 6,8)]对预水解液的萃取性能。结果表明,随着咪唑类离子液体阳离子烷基链长度的增加,离子液体对抑制物的萃取性能下降,具有更强电负性的阴离子为BF₄^-的离子液体比阴离子为PF₆^-的离子液体萃取效率更高。通过比较糖与抑制物的萃取率,最终选择[C₈mim][BF₄]作为预水解液的萃取剂,结果显示其对主要抑制物甲酸、乙酸、5-羟甲基糠醛的萃取率分别为53.22%、47.53%和85.13%,总酚的萃取率为65.05%,而糖的损失率在6%以内。     

多级离心逆流萃取萘普生对映体模拟及实验研究

基于萘普生(NAP)对映体的单级手性萃取数学模型和质量守恒定律,建立了多级离心逆流萃取萘普生对映体数学模型。采用Matlab语言编写程序模拟了相比、萃取剂浓度、水相pH值等参数对萃取相出口对映体过剩量和产率的影响,并经实验研究对模型模拟进行验证。结果表明:采用中间进料,对映体浓度[R,S-NAP]=0.025 mol·L^-1、萃取剂浓度[C]=0.050 mol·L^-1、相比W/O=7、水相pH=2.5、温度T=5℃时,经10级离心逆流萃取后萃取相出口S-NAP对映体过剩量为45%,相应的产率60%,实验结果和模型模拟值符合得很好。     

反应萃取分离2-苯基丁酸对映体的动力学

通过恒界面池法进行了羟乙基-β-环糊精反应萃取2-苯基丁酸对映体的动力学研究。采用双膜理论和均相反应模型描述了萃取过程的相际传质机理,并考察了搅拌速率、界面面积、对映体初始浓度和萃取剂初始浓度等因素对2-苯基丁酸对映体的萃取动力学的影响。实验结果表明羟乙基-β-环糊精与2-苯基丁酸对映体之间的包合反应属于“快反应”;2-苯基丁酸对映体反应分级数为1,羟乙基-β-环糊精反应分级数为2;（+）-2-苯基丁酸和（-）-2-苯基丁酸在278 K下的反应速率常数分别为2.829×10^-4、1.803×10^-4 m⁶·mol^-2·s^-1。该萃取动力学研究为大规模生产中的反应萃取过程的设计和操作以及设备的设计和过程强化提供了科学的依据。     

氮浓度对新型生物电化学-颗粒污泥反应器运行的影响

探讨了新型生物电化学-颗粒污泥反应器在不同进水氮浓度下的脱氮效能与产电性能,并从颗粒污泥的关键酶活性、胞外聚合物组分以及微生物群落分布等角度系统研究了其影响机制。结果表明,COD、NO₃^--N、NO₂^--N和溶解性甲烷在第Ⅰ、Ⅱ、Ⅲ、Ⅳ阶段（进水NO₃^--N和NO₂^--N浓度分别为60 mg·L^-1和20 mg·L^-1、100 mg·L^-1和40 mg·L^-1、140 mg·L^-1和60 mg·L^-1、180 mg·L^-1和80 mg·L^-1）均得以有效去除,其中COD去除率在第Ⅳ阶段效果最佳,去除率达96%以上,NO₃^--N出水浓度在第Ⅱ阶段更为稳定,其去除率达99%以上,NO₂^--N去除率在各阶段均达99%以上;该反应器最大的功率密度与输出电压值为第Ⅳ阶段的4号格室,分别为471.2 mV·m^-3和608.1 mV。污泥疏松型胞外聚合物（LB-EPS）中多糖与蛋白含量最高为第Ⅱ阶段的5号格室,分别为13.7 mg·g^-1和14.7 mg·g^-1;1号格室污泥中辅酶F₄₂₀活性最低,进水氮浓度的增大提高了污泥中蛋白酶活性。由第Ⅰ阶段至第Ⅳ阶段,该反应器中变形菌门（Protebaoteria）相对丰度减少,而绿弯菌门（Chloroflexi）、厚壁菌门（Firmicutes）和浮霉菌门（Planctomycetes）相对丰度增加;具有脱氮作用的陶厄氏菌属（Thauera）在1号格室减少了8.64%,但该反应器脱氮效果未受到影响;甲烷丝状菌属（Methanothrix）在4号格室相对丰度增至12.3%,表明产甲烷菌可在该反应器中与其他菌群联营共存。     

Influence of nitrogen concentration on operation of a novel bio-electrochemical-granular sludge reactor

The performance of nitrogen removal and electricity generation of a novel bio-electrochemical-granular sludge reactor at different influent nitrogen concentration was investigated. The impact mechanism of granular sludge, key enzyme activity, extracellular polymer composition and microbial community distribution were systematically studied. The results showed that COD, NO₃^--N, NO₂^--N and dissolved methane were efficiently removed in stages Ⅰ, Ⅱ, Ⅲ and Ⅳ (Influent NO₃^--N and NO₂^--N concentrations were 60 and 20 mg·L^-1, 100 and 40 mg·L^-1, 140 and 60 mg·L^-1, 180 and 80 mg·L^-1, respectively). The removal efficiency of COD was the highest in stage Ⅳ, and it was above 96%. The effluent concentration of NO₃^--N was the most stable at stage Ⅱ, and the removal efficiency was over 99%. The NO₂^--N removal efficiency was above 99% in each stage. In stage Ⅳ, the maximum power density and output voltage was 471.2 mV·m^-3 and 608.1 mV at the fourth compartment, respectively. The polysaccharide and protein content of LB-EPS was the highest in stage Ⅱ of the fifth compartment, 13.7 mg·g^-1 and 14.7 mg·g^-1, respectively. Coenzyme F₄₂₀ activity was the lowest in the first compartment. The protease activity of the sludge was increased due to the increase of influent nitrogen concentration. From stage Ⅰ to stage Ⅳ, the relative abundance of Protebaoteria was decreased, while the relative abundance of Chloroflexi, Firmicutes and Planctomycetes were increased. Although Thauera with denitrification effect was decreased by 8.64% in the first compartment, the nitrogen removal was still well in the reactor. The relative abundance of Methanothrix was increased to 12.3% in the fourth compartment, indicating that Methanothrix could co-exist with other bacteria in the reactor.     

离子液体用于燃油萃取脱硫的选择与过程优化

针对基于COSMO-SAC模型分子设计方法的准确性问题,采用离子液体脱硫机理分析和实验的方法对其进行了验证,即对[HMIM] [BF₄]、[HMIM] [PF₆]、[BMIM] [BF₄]、[BMIM] [PF₆]、[EMIM] [BF₄]、[EMIM] [PF₆] 6种离子液体作萃取剂时的脱硫效果进行了脱硫机理的分析和实验的验证,得到的脱硫性能排序与离子液体分子设计结果基本一致,且均认为[HMIM] [PF₆]脱硫率较高。以[HMIM] [PF₆]为萃取剂,通过液相色谱法测定萃取后的液相组成,考察萃取时间、萃取温度、剂油比3个因素对脱硫率、分配系数和选择性系数的影响。通过正交实验设计确定了萃取时间40 min、萃取温度20℃、剂油比2：1为较优操作条件,单次脱硫率为72.74%,四级萃取可将模型油的含硫量由1200 μg·g^-1降至6.98 μg·g^-1,符合国Ⅴ标准。     

Experimental and modeling studies on the enantio-separation of 3,5-dinitrobenzoyl-(R),(S)-leucine by continuous liquid–liquid extraction in a cascade of centrifugal contactor separators

The continuous enantioselective liquid–liquid extraction of aqueous 3,5-dinitrobenzoyl-(R),(S)-leucine (A_R,S) using O-(1-t-butylcarbamoyl)-11-octadecylsulfinyl-10,11-dihydro-quinine (C, a cinchona alkaloid) as extractant in 1,2-dichloroethane (DCE) was studied experimentally in a countercurrently operated pilot scale cascade of six centrifugal contactor separators (CCS) at 294 K. The extractant was efficiently recovered by back-extraction in a single CCS allowing the cascade to be run continuously for 10 h. The steady-state ee of A_R (ee_R) in the raffinate was 42% at a 99% yield, the A_S was obtained with high purity (98% ee_S) and a yield of 55% in the back-extraction raffinate. In total 2.23 g of A_S was obtained at steady-state operation from 8.11 g racemate feed. Deterioration of the ee in time was not observed, demonstrating the robustness of the chemistry. The experiments were modeled using an equilibrium stage approach. The correlation between model and experiment was satisfactory. The model was applied to optimize the production of both enantiomers in >97% ee. At zero reflux, 12 stages are required for 99% ee for both enantiomers. Application of a reflux allows a 25% reduction of the total liquid flow through the system by reduction of the wash feed as well as a reduction in the number of stages from 12 to 11. With a configuration of 12 CINC-V02’s operating at an aqueous feed flow of 360 mL/min, the model predicts that 17.7 kg racemate per week may be separated into both enantiomers with 99% ee using only 60 g of extractant.     

不同电子受体配比对反硝化除磷特性及内碳源转化利用的影响

以A²/O-生物接触氧化(biological contact oxidation,BCO)系统反硝化除磷活性污泥为研究对象,通过投加不同浓度的NO₂^--N和NO₃^--N(30 mg·L^-1),考察了反硝化聚磷菌(denitrifying polyphosphate accumulating organisms,DPAOs)在不同电子受体配比(NO₂^--N:NO₃^--N0, 0.2:0.8, 0.4:0.6, 0.5:0.5, 0.6:0.4)条件下的脱氮除磷特性。结果表明:乙酸钠为DPAOs用于反硝化除磷的理想碳源,且其浓度为200 mg·L^-1时最佳;仅以NO₃^--N为电子受体进行缺氧吸磷反应时,NO₃^--N的投加量为30 mg·L^-1时较为合适;以NO₂^--N作为电子受体,未经 驯化的DPAOs,短时间内很难利用NO₂^--N,但低浓度的 (6 mg·L^-1)不会影响DPAOs以 作电子受体进行反硝化除磷;同时,NO₂^--N对于DPAOs吸磷作用的抑制程度明显强于 反硝化作用,当NO₂^--N浓度达到18 mg·L^-1时,吸磷反应基本停止;此外,较高浓度的NO₂^--N不仅会抑制聚羟基脂肪酸酯(poly-β-hydroxyalkanoate,PHA)的分解利用,且会使PHA分解产生的能量较多地用于储存糖原(glycogen,Gly),而所分解利用的PHA中90%以上为聚-β-羟基丁酸酯(poly-β-hydroxybutyrate,PHB)。     

疏水性离子液体-中性磷氧萃取剂萃取稀土元素的应用

液液萃取广泛应用于稀土元素的分离回收,为了便于相的分离,通常采用疏水性萃取剂。基于液液萃取的特性,通过微波辅助法合成了疏水性离子液体1-丁基-3-甲基咪唑六氟磷酸盐（[BMIM][PF₆]）。分别探究了[BMIM][PF₆]搭配不同中性磷氧萃取剂对稀土元素中Nd³⁺和Pr³⁺的萃取研究。结果表明1-丁基-3-甲基咪唑六氟磷酸盐-三正辛基氧化磷（[BMIM][PF₆]-TOPO）为最适宜萃取体系。在最适宜萃取体系下,探究了时间、温度、pH值、V（A）/V（O）（水相稀土离子/有机相萃取体系）和萃取组分体积比对萃取效率的影响。结果表明：萃取时间为20 min、温度为25℃、pH值=6.0、V（A）/V（O）=1.0、V_[BMIM][PF6]：V_TOPO=1：1,体系对于Nd³⁺的萃取效果最佳,萃取率可达97.8%;萃取时间为25 min、温度为25℃、pH值=6.0、V（A）/V（O）=1.0、V_[BMIM][PF6]：V_TOPO=1：1,体系对于Pr³⁺的萃取效果最佳,萃取率可达94.2%;萃取过程为放热反应,反应焓变分别为ΔH（Nd³⁺）=-38.43 kJ·mol^-1,ΔH（Pr³⁺）=-28.76 kJ·mol^-1。     

离子液体体系用于盐湖卤水提取锂

3种咪唑类离子液体:1-丁基-3-甲基咪唑六氟磷酸盐([C₄mim][PF₆])、1-己基-3-甲基咪唑六氟磷酸盐([C₆mim][PF₆])、1-辛基-3-甲基咪唑六氟磷酸盐([C₈mim][PF₆])被作为绿色溶剂用于盐湖卤水分离镁锂, 建立了以离子液体(ILs)、磷酸三丁酯(TBP)分别为萃取介质和萃取剂的盐湖卤水锂萃取体系, 并与使用传统有机溶剂磺化煤油和氯仿的萃取效果进行了对比。研究发现, 该离子液体体系较使用传统挥发性有机溶剂的萃取体系有更高的萃取率。锂的萃取率随离子液体中烷基碳原子数的减小而增加。详细考察了溶液pH、离子液体浓度、相比对萃取效率的影响, 获得了离子液体体系萃取的最优条件。在最佳萃取条件下, 3种离子液体体系对锂的单级萃取效率均高于80%, 分离系数最高达到100以上。机理研究表明:离子液体体系是以阳离子交换实现对锂的萃取, Li⁺与TBP形成[Li·2TBP]⁺络合物进入有机相。