Investigation of MBE grown GaAs/AlGaAs/InGaAs heterostructures

This paper reports on the influence of the In mole fraction variation (0.1≤x≤0.25) of MBE grown pseudomorphic GaAs/Al_yGa_1−yAs/In_xGa_1−xAs heterostructures on the material quality and the performance of the fabricated devices. For x=0.1–0.15, the carrier mobility in the samples was 4500 cm² V⁻¹ s (at 300 K) and 37 000 cm²V⁻¹ s (at 77 K) and decreased significantly at low temperatures as x was increasing up to 0.25. Transistors with gate length of 0.8 m and In_0.1Ga_0.9As channels exhibited transconductances of 200–220 mSm mm⁻¹ and output conductances of 0.15–0.20 mSm mm⁻¹, while gate-source breakdown voltages were 27–28 V. Delay times of the designed and fabricated ICs frequency dividers by 2 were 130–140 ps.     

Doping and electrical characteristics of in-situ heavily B-doped Si1−x−yGexCy films epitaxially grown using ultraclean LPCVD

Doping and electrical characteristics of in-situ heavily B-doped Si_1−x−yGe_xC_y (0.22<x<0.6, 0<y<0.02) films epitaxially grown on Si(100) were investigated. The epitaxial growth was carried out at 550°C in a SiH₄–GeH₄–CH₃SiH₃–B₂H₆–H₂ gas mixture using an ultraclean hot-wall low-pressure chemical vapor deposition (LPCVD) system. It was found that the deposition rate increased with increasing GeH₄ partial pressure, and only at high GeH₄ partial pressure did it decrease with increasing B₂H₆ as well as CH₃SiH₃ partial pressures. With the B₂H₆ addition, the Ge and C fractions scarcely changed and the B concentration (C_B) increased proportionally. The C fraction increased proportionally with increasing CH₃SiH₃ partial pressures. These results can be explained by the modified Langmuir-type adsorption and reaction scheme. In B-doped Si_1−x−yGe_xC_y with y=0.0054 or below, the carrier concentration was nearly equal to C_B up to approximately 2×10²⁰ cm⁻³ and was saturated at approximately 5×10²⁰ cm⁻³, regardless of the Ge fraction. The B-doped Si_1−x−yGe_xC_y with high Ge and C fractions contained some electrically inactive B even at the lower C_B region. Resistivity measurements show that the existence of C in the film enhances alloy scattering. The discrepancy between the observed lattice constant and the calculated value at the higher Ge and C fraction suggests that the B and C atoms exist at the interstitial site more preferentially.     

Structural characterization of ion-beam-induced epitaxially crystallized thin layers of III–V and IV–IV semiconductors

Structural properties of ion-beam-induced epitaxial crystallization (IBIEC) for amorphous layers of GaAs on GaAs(100), BP on BP(100) and Si_1−xGe_x and Si_1−x−yGe_xC_y on Si(100) have been investigated. Crystallization was induced by ion bombardment with 400 keV Ne, Ar or Kr at 150 °C for GaAs and at 350 °C for BP. Epitaxial crystallization up to the surface was observed both in GaAs and BP at temperatures much below those required for the solid phase epitaxial growth (SPEG). The growth rate per nuclear energy deposition density has shown a larger dependence on ion dose rate in cases of heavier ion bombardments both for GaAs and BP. Crystallization of a-GaAs with ions whose projected ranges are within the amorphous layer thickness was also observed at 150 °C. Epitaxial crystallization of Si_1−xGe_x and Si_1−x−yGe_xC_y layers (x = 0.13 and y = 0.014 at peak concentration) on Si(100) formed by high-dose implantation of 80 keV Ge and 17 keV C ions has been observed in the IBIEC process with 400 keV Ar ion bombardments at 300–400 °C. Crystalline growth by IBIEC has shown a larger growth rate in Si_1−x−yGe_xC_y/Si} than in Si_1−xGe_x/Si} with the same Ge concentration for all bombardments under investigation. X-ray rocking-curve measurements have shown a strain-compensated growth in Si_1−x−yGe_xC_y/Si}, whereas Si_1−xGe_x/Si} samples have shown a growth with strain accommodation.     

Bond-lengths of the atomic nearest-neighbor and next-nearest-neighbor in A1−xBxC1−yDy III–V solid solutions

On the basis of the FDUC model and the hypothesis of the constant covalent radii, the expressions of the atomic nearest-neighbor and the next-nearest-neighbor bond-lengths were derived for A_1−xB_xC_1−yD_y III–V quaternary solid solutions. This set of bond-length expressions predicts the averaged bond-lengths and bond angles at any concentration (x, y) for the III–V pseudobinary and quaternary solid solutions, which are only dependent on the lattice parameters and the concentrations of the pure end compounds. When x=0, 1 or y=0, 1, A_1−xB_xC_1−yD_y III–V quaternary solid solutions degenerate into the relative pseudobinary solid solutions, in which the nearest-neighbor and the next-nearest-neighbor bond-lengths agree well with the experimental results. Further discussion and comparison with other theoretical models are also given in this paper.     

Ag glasses based on Zn-phosphate

The partial substitution of Zn²⁺ for Ag⁺ in Ag₄P₂O₇ leads to the formation of a wide glassy domain of composition [Ag₄P₂O₇] _(1−y) [Zn₂P₂O₇] _(y) with 0.20y0.87. The introduction of AgI in these materials results in a new series of glasses of formula [(Ag₄P₂O₇)_(1−y) (Zn₂P₂O₇)_(y)] _(1−X) [AgI] _(x), which domain for the composition y = 0.25 corresponds to 0x 0.64. The structure as well as the thermal and electrical properties of these materials are compared with those of the [AgPO₃] _(1−X) [AgI] _(x) and [Ag₄P₂O₇] _(1−x) [AgI] _(x) glasses.     

Optical transitions near the band edge in bulk CuInxGa1−xSe2 from ellipsometric measurements

From the analysis of the variation of optical absorption coefficient with incident photon energy between 0.8 and 2.6 eV, obtained from ellipsometric data, the energy E_G of the fundamental absorption edge and E_G′ of the forbidden direct transition for CuIn_xGa_1−xSe₂ alloys are estimated. The change in E_G and the spin-orbit splitting Δ_SO=E_G′−E_G with the composition x can be represented by parabolic expression of the form E_G(x)=E_G(0)+ax+bx² and Δ_SO(x)=Δ_SO(0)+a′x+b′x², respectively. b and b′ are called “bowing parameters”. Theoretical fit gives a=0.875 eV, b=0.198 eV, a′=0.341 eV and b′=−0.431 eV. The positive sign of b and negative sign of b′ are in agreement with the theoretical prediction of Wei and Zunger [Phys. Rev. B 39 (1989) 6279].     

Molecular beam epitaxy synthesis of Si1−yCy and Si1−x−yGexCy alloys and Ge islands using an electron cyclotron resonance argon/methane plasma

We report the growth of Si_1−yC_y and Si_1−x−yGe_xC_y alloys on Si(001) by electron cyclotron resonance plasma-assisted Si molecular beam epitaxy using an argon/methane gas mixture. Various Si/Si_1−yC_y and Si/Si_1−x−yGe_xC_y multilayers have been grown and characterized principally by X-ray diffraction and Raman spectroscopy. The influence of growth parameters and electron cyclotron resonance plasma source operating conditions on the C substitutional incorporation was studied. Under optimum growth conditions the structures show good structural properties and sharp interfaces with carbon being essentially substitutionally incorporated up to concentrations of 1%. No significant carbon incorporation was measured in films grown under a high methane partial pressure without plasma excitation. Si_1−x−yGe_xC_y layers grown with this technique exhibit the strain compensation and enhanced thermal stability expected for these ternary alloys. Carbon pre-deposition of Si through surface exposure to the argon/methane plasma is shown to act as an antisurfactant on the growth of Ge islands by suppressing the formation of a Ge wetting layer on the surface.     

Chemical vapour deposition of molybdenum carbides: aspects of phase stability

Thin films of different molybdenum carbides (δ-MoC_1−x, γ′-MoC_1−x and Mo₂C) have been deposited from a gas mixture of MoCl₅/H₂/C₂H₄ at 800°C by CVD. The H₂ content in the vapour has a strong influence on the phase composition and microstructure. Typically, high H₂ contents lead to the formation of nanocrystalline δ-MoC_1−x films while coarse-grained γ′-MoC_1−x is formed with an H₂-free gas mixture. This phase has previously only been synthesized by carburization of Mo in a CO atmosphere and it has therefore been considered as an oxycarbide phase stabilized by the presence of oxygen in the lattice. Our results, however, show that γ′-MoC_1−x films containing only trace amounts of oxygen can be deposited by CVD. Stability calculations using a FP-LMTO method confirmed that the γ′-MoC_1−x phase is stabilized by oxygen but that the difference in energy between e.g. δ-MoC_0.75 and oxygen-free γ′-MoC_0.75 is small enough to allow the synthesis of the latter phase in the absence of kinetic constraints. Annealing experiments of metastable δ-MoC_1−x and γ′-MoC_1−x films showed two different reaction products suggesting that kinetic effects play an important role in the decomposition of these phases.     

Characterization of GaN epitaxial layers on SiC substrates with AlxGa1−xN buffer layers

High quality GaN epitaxial layers were obtained with Al_xGa_1−xN buffer layers on 6H–SiC substrates. The low-pressure metalorganic chemical vapor deposition (LP-MOCVD) method was used. The 500 Å thick buffer layers of Al_xGa_1−xN (0≤x≤1) were deposited on SiC substrates at 1025°C. The FWHM of GaN (0004) X-ray curves are 2–3 arcmin, which vary with the Al content in Al_xGa_1−xN buffer layers. An optimum Al content is found to be 0.18. The best GaN epitaxial film has the mobility and carrier concentration about 564 cm² V⁻¹ s⁻¹ and 1.6×10¹⁷ cm⁻³ at 300 K. The splitting diffraction angle between GaN and Al_xGa_1−xN were also analyzed from X-ray diffraction curves.     

Lattice dynamics of Ga1−xAlxAs studied by ab initio calculations

We have calculated the phonon dispersion and phonon density of states of superlattices of Ga_1−xAl_xAs for x=0.0, 0.25, 0.75 and 1.0 using the ab initio method within the supercell approach and calculating the Hellmann–Feynman forces. A noticeable difference of force constants between Ga–As and Al–As atomic pairs has been found. In any case, Al atoms vibrate in well-separated high-frequency optic modes.     

Influence of disorder on electronic structure and magnetic properties in Fe-rich Fe–Si alloys

We present the results of ab initio calculations of the spin-polarized electronic structure of disordered bcc and fcc Fe_1 − xSi_x alloys from dilute solid solutions of Si on iron up to FeSi intermetallic compound composition (x=0.01..0.5) and ordered intermetallic phases FeSi in B20 structure and Fe₃Si in DO₃ structure. The self-consistent calculations were performed with the coherent potential approximation within the Korringa–Kohn–Rostoker method (KKR–CPA) for disordered case and by using the tight-binding linear muffin–tin orbital (TB LMTO) method for intermetallic compounds. In the last case the supercell approach has been utilized in order to take into account the structural defects for this ordered phase. In particular, we have performed a series of calculations in the BCC Fe_1 − xSi_x alloys with x=0.01, 0.015, 0.1, 0.15, 0.25.     

Photoelectrochemical investigations of n-CdSe1−xTex thin film electrodes

An electrode/electrolyte interface has been formed between an n-type CdSe_1−xTe_x (0≤x≤1) alloyed/mixed type semiconductor and a sulphide/polysulphide redox electrolyte. It has been investigated through the current–voltage, capacitance–voltage and spectrally selective properties. The dependence of the dark current through the junction and the junction capacitance on the voltage across the junction have been examined and analysed. It appeared that the current transport mechanism across the junction is strongly influenced by the recombination mechanism at the interface and series resistance effects. Upon illumination of the interface with a light of 20 mW cm⁻², an open circuit voltage of the order of 0.35 V and a short circuit current of 212 μA cm⁻² have been developed (for x=0.2), yielding an efficiency of energy conversion equal to 0.2% and a form factor of 45%. The action spectra in the 450–1000 nm wavelength range showed presence of the interface states at the electrode/electrolyte interface. The magnitudes of the barrier heights at the interfaces were also determined. It has been seen that a significant improvement in the electrochemical performance of a cell is noticed for the electrode composition with x=0.2.     

Synthesis and humidity sensitive properties of nanocrystalline Ba1−xSrxTiO3 thick films

Nanocrystalline Ba_1−xSr_xTiO₃ (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) precursors were synthesized using the stearic acid gel method. After the precursors had been calcined at 600–950°C for 0.5–1 h, nanocrystalline powders with the cubic perovskite structure were obtained and these were made into thick films. The powder samples were characterized by differential thermal analysis, X-ray diffraction and transmission electron microscopy, and the thick film samples were characterized by scanning electron microscopy and X-ray diffraction. The humidity-sensitive properties of the nanocrystalline Ba_1−xSr_xTiO₃ thick films were investigated. The results show that these nanocrystalline thick films possess higher humidity sensitivity and lower resistance than those of conventional materials.     

Dielectric and piezoelectric properties of sol–gel derived Ca doped PbTiO3

Synthesis of Ca doped PbTiO₃ powder by a chemically derived sol–gel process is described. Crystallization characteristics of different compositions Pb_1−xCa_xTiO₃ (PCT) with varying calcium (Ca) content in the range x = 0–0.45 has been investigated by DTA/TGA, X-ray diffraction and scanning electron microscopy. The crystallization temperature is found to decrease with increasing calcium content. X-ray diffraction reveals a tetragonal structure for PCT compositions with x ≤ 0.35, and a cubic structure for x = 0.45. Dielectric properties on sintered ceramics prepared with fine sol–gel derived powders have been measured. The dielectric constant is found to increase with increasing Ca content, and the dielectric loss decreases continuously. Sol–gel derived Pb_1−xCa_xTiO₃ ceramics with x = 0.45 after poling exhibit infinite electromechanical anisotropy (k_t/k_p) with a high d₃₃ = 80 pC/N, ′ = 298 and low dielectric loss (tan δ = 0.0041).     

Optical properties of a-(Se70Te30)100−x(Se98 Bi2)x thin films

Measurements of optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary part of the dielectric constant) have been made on a-(Se₇₀Te₃₀)_100−x (Se₉₈Bi₂)_x thin films (where x=0, 5, 10, 15 and 20) of thickness 2000 Å in the wavelength range 450–1000 nm. It is found that the optical bandgap decreases with the increase of Se₉₈Bi₂ concentration in the a-(Se₇₀Te₃₀)_100−x(Se₉₈Bi₂)_x system. The value of refractive index (n) decreases, while the extinction coefficient (k) increases with increasing photon energy. The results are interpreted in terms of concentration of localized states varying effective Fermi level.     

Composition and substrate temperature dependence of structural and optical studies on ZnSexCdS1−x alloy films

Thin (t−0.60 μm) films of ZnSe_xCdS_1−x were formed by vacuum evaporation on glass substrates held at 350 and 470 K. XRD studies showed that all the films were polycrystalline in nature. Films with x0.70 were hexagonal whereas films with x0.80 were cubic in structure. The structural transition was in the range 0.70<x<0.80. The lattice parameter was higher in films formed at a higher temperature. The lattice parameter followed Vegard's law. Grain size increased with substrate temperature. From the optical transmission spectra recorded in the wavelength range 300–2500 nm, the extinction coefficient, refractive index and band gaps were obtained. Band gap values showed a downward bowing with ‘x' with a bowing parameter of 0.40 eV.     

Contribution to the comprehension of dissipation phenomena in lead zirconate titanate: aliovalent doping effect

By the solid reaction method, undoped, potassium doped and niobium doped lead zirconate titanate (PZT) are elaborated. The mechanical losses measured in the range of the Hz as a function of temperature shows two peaks R₁ and R₂, and a ferroelectric transition peak P₁ between ferroelectric and para-electric states on the undoped PZT—Pb(Zr_0.54Ti_0.46)O₃—noted PZT54/46. Potassium doped PZT—Pb_1−xK_x(Zr_0.54Ti_0.46)O₃—shortly called PKZT 100x/54/46 shows an increase in the height of both the peaks at a doping content, x, less than 0.5 at.% but an opposite effect is observed above this value. Niobium doped PZT—Pb[(Zr_0.54Ti_0.46)_1−yNb_y]O₃—shortly called PNZT 100y/54/46, shows the vanish of the R₂ peak and the decrease of the height of the R₁ peak when the doping content increases.     

Influence of praseodymium oxide/cobalt oxide ratio on microstructure and electrical properties of zinc oxide varistor ceramics

The microstructure and electrical properties of varistor ceramics, which are composed of (99.5–x–y)ZnO+xPr₆O₁₁+yCoO+0.5Dy₂O₃ system, were investigated with Pr₆O₁₁/CoO mole ratio (x/y=0.5/0.5, 0.5/1.0, 1.0/0.5, 1.0/1.0) and sintering temperature. The density of varistor ceramics with Pr₆O₁₁=1.0 was almost constant with sintering temperature, whereas it was increased noticeably in Pr₆O₁₁=0.5. Increasing Pr₆O₁₁ content enhanced the densification for any CoO content and the density was greatly affected not by CoO content but by Pr₆O₁₁ content. The varistor ceramics with Pr₆O₁₁/CoO=0.5/1.0 exhibited a higher nonlinearity than any other composition ratios. In particular, the varistor ceramics sintered at 1350 °C. exhibited the best electrical properties, with nonlinear exponent of 37.8, leakage current of 7.6 μA, and dissipation factor of 0.059. It was found that Pr₆O₁₁/CoO ratio greatly affects various characteristics of varistor ceramics.     

Preparation and characterization of lithium nickel cobalt oxide powders via a wet chemistry processing

Nickel-rich phases of the solid solutions, LiNi_1−yCo_yO₂ (y=0.1, 0.2, 0.3), were synthesized by a sol–gel method with citric acid as a chelating agent. Various initial conditions were studied in order to find the optimal conditions for the synthesis of LiNi_0.8Co_0.2O₂. The discharge capacity for the compound synthesized under an optimal synthesis condition of 800 °C for 12 h was found to be 187 mAh g⁻¹ in the 1st cycle and it was 176 mAh g⁻¹ after 10 cycles. The other nickel-rich phases, namely, LiNi_0.9Co_0.1O₂ and LiNi_0.7Co_0.3O₂ showed 1st-cycle discharge capacities of 144 and 163 mAh g⁻¹, respectively. The corresponding capacity values were 140 and 159 mAh g⁻¹ in the 10th cycle. Excess lithium stoichiometric phases, Li_xNi_0.8Co_0.2O₂, where x=1.10, 1.15 and 1.20, resulted in decreased capacity. Structural and electrochemical properties of the synthesized compounds were compared with those of a commercial LiNi_0.8Co_0.2O₂ sample. The effect of calcination temperature and duration, excess lithium stoichiometry and divalent strontium doping in LiNi_0.8Co_0.2O₂ are described. Doping with strontium improved both the capacity and cycling performance of LiNi_0.8Co_0.2O₂.     

Structural investigation of bulk and thin film PLZT using X-ray absorption spectroscopy

Thin film electro-optic and non-linear optical materials are of interest for applications in high-speed integrated optical devices. Materials of the system Pb_1−x/100La_x/100(Zr_y/100 Ti_1−y/100)_1−x/400O₃ or PLZT x/y/(100−y) are attractive since they can be integrated into Si and GaAs substrates using suitable deposition techniques. In this investigation we examine the structural properties of r.f. magnetron sputter-deposited PLZT using X-ray absorption near-edge spectroscopy (XANES). For XANES analysis, four samples were selected: (1) a highly oriented PLZT 28/0/100 film of ≈ 4500 Å deposited on SiO₂; (2) a highly oriented PLZT 28/0/100 film of ≈ 4500 Å deposited on a 2 ωm SiO₂ buffer layer over a Si(100) substrate; (3) a highly oriented PLZT 28/0/100 film of ≈4500 Å deposited on Al₂O₃ (1 02); and (4) a commercial ceramic wafer of PLZT 9/65/35. The XANES experiments were performed at the Stanford Synchrotron Radiation Laboratory (SSRL) using electron yield and fluorescence techniques. Data was taken at the Ti K-edge (4966.4eV) and compared to reference spectra. Of the reference spectra, the Ti K-edge spectra of the PLZT most closely resemble perovskite (SrTiO₃). The surface and bulk thin film are similar and all the 28/0/100 spectra resemble the spectra of 9/65/35, indicating similar cubic perovskite structures for these materials.