Dielectric and piezoelectric properties of Bi<Subscript>1/2</Subscript>Na<Subscript>1/2</Subscript>TiO<Subscript>3</Subscript>–SrTiO<Subscript>3</Subscript> lead–free ceramics

This study investigated the microstructure, crystal structure, and electrical properties of (1???x)Bi_1/2Na_1/2TiO₃–xSrTiO₃ (BNST100x; x?=?0.20, 0.22, 0.24, 0.26, 0.28, and 0.30) lead?free piezoceramics. The average grain size of BNST100x ceramics decreased with increasing SrTiO₃ content. A phase transition from nonergodic relaxor (NER) to ergodic relaxor (ER) was observed at x?=?0.26, and the highest unipolar strain under 4 kV/mm electric field, of 0.25% (d₃₃^*?≈?620 pm/V), was obtained at x?=?0.28. We found that the BNST26 and BNST28 compositions yielded the competitive advantage of larger strain values under lower operating fields compared with other BNT–based lead–free piezoelectric ceramics. Therefore, we regard these ceramics as promising candidates for actuator applications.     

The effect of sintering temperature and time on the growth of single crystals of 0.75 (Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>)TiO<Subscript>3</Subscript>–0.25 SrTiO<Subscript>3</Subscript> by solid state crystal growth

Materials in the (Na_0.5Bi_0.5)TiO₃–SrTiO₃ system are of interest for use as lead-free piezoelectric actuators due to high electric-field induced strains. Piezoelectric properties may be further improved by growing single crystals but as yet work on single crystal growth in this system is limited. In the present work, single crystals of composition 0.75 (Na_0.5Bi_0.5)TiO_3?0.25 SrTiO₃ were grown by solid state crystal growth (SSCG) on [001] SrTiO₃ seed crystals and the dependence of crystal growth distance and matrix grain growth on sintering temperature investigated. Electron backscattered diffraction and X-ray diffraction analysis show that the single crystals grow epitaxially on the seed crystals. Energy dispersive spectroscopy indicates that the grown crystals are slightly Na-deficient, while X-ray photoelectron spectroscopy indicates the presence of oxygen vacancies. Single crystal growth distance, mean matrix grain size and grain size distribution as a function of sintering temperature and time are presented. Increasing the sintering temperature increases both single crystal and matrix grain growth rates. The optimum single crystal growth temperature is found to be 1250°C. The effect of sintering temperature on the single crystal and matrix grain growth behavior is explained using the mixed control mechanism of microstructural evolution.     

Large signal electrical property of CuO-doped of a Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>–SrTiO<Subscript>3</Subscript>

This report describes the sintering and ferroelectric characteristic of 0.76 Bi_0.5Na_0.5TiO₃ (BNT)–0.26SrTiO₃ (ST) with CuO addition, synthesized by using a solid-state reaction. The XRD, microstructure, and density results reveal that Cu element reduces the sintering temperature from 1150 to 1000 °C. In dielectric study, CuO addition induces the increase of relaxation behavior for 26ST ceramic in the high temperature regime. In the low temperature regime (< 150 °C), the Cu doping to 26ST accelerates the degree in freezing of dipole, presumably due to the interaction between A site vacancy and nanodomain boundaries. The electromechanical properties of 26ST ceramics with CuO doping show a significant decay in frequency dependence of polarization and strain, which might be related to the formation of A-site cation vacancy.     

Lead-free K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>NbO<Subscript>3</Subscript>–Bi<Subscript>0.5</Subscript>Li<Subscript>0.5</Subscript>ZrO<Subscript>3</Subscript>–BiAlO<Subscript>3</Subscript> ternary ceramics: Structure and piezoelectric properties

Lead-free perovskite (0.995–x)(K_0.5Na_0.5)NbO₃–x(Bi_0.5Li_0.5)ZrO₃–0.005BiAlO₃ ternary piezoelectric ceramics were projected and prepared by a conventional solid-state method. A research was conducted on the effects of (Bi_0.5Li_0.5)ZrO₃ content on the structure and piezoelectric properties of the ceramics. By combining the X-ray diffraction patterns with the temperature dependence of dielectric properties, a rhombohedral–orthorhombic–tetragonal phase coexistence was identified for the ceramics with 0.02 ≤ x ≤ 0.025, and a rhombohedral–tetragonal phase boundary was determined in the composition x = 0.03. Upon further increasing the (Bi_0.5Li_0.5)ZrO₃ content, the rhombohedral–tetragonal phase boundary transformed to a single rhombohedral structure with x ≥ 0.035. An obviously improved piezoelectric activity was obtained for the ceramics with compositions in and around the rhombohedral–tetragonal phase boundary, among which the composition x = 0.025 exhibited the maximum values of piezoelectric constant d ₃₃, and planar and thickness electromechanical coupling coefficients (k _p and k _t), of 252 pC/N, 0.366, and 0.466, respectively. In addition, the ceramic with x = 0.025 was found to possess a relatively high Curie temperature of 368 °C, suggesting it may have a prospect for applications at elevated ambient temperatures.     

Electromechanical properties of ternary BiFeO<Subscript>3</Subscript>−0.35BaTiO<Subscript>3</Subscript>–BiGaO<Subscript>3</Subscript> piezoelectric ceramics

In the present work, composition dependent crystal structure, ferroelectric, piezoelectric, and temperature dependent dielectric properties of the BiGaO₃-modified (1–x)(0.65Bi_1.05FeO₃–0.35BaTiO₃) (BFBT35–xBG, where x?=?0.00–0.03) lead-free ceramics were systematically investigated by solid-state reaction method, followed by water quenching process. The substitution of BG successfully diffuses into the lattice of the BFBT ceramics, without changing the pseudo-cubic structure of the samples. The scanning electron microscopy (SEM) results revealed that the average grain size was increased with BG-content in BFBT system. The BFBT–xBG ceramics showed a maximum in permittivity (?_max) at temperatures (T_max) above 500 °C in the compositional range of 0.00?≤?x?≤?0.03. The electro-strain is measured to be 0.125% (d^*₃₃ ~ 250 pm/V) under unipolar fields (5 kV/mm) for BFBT–0.01BG ceramics. The same composition (x?=?0.01), large static piezoelectric constant (d₃₃ ~ 165 pC/N) and electromechanical coupling factor (k_p ~ 25%) were obtained. The above investigated characterizations suggests that BFBT–BG material is favorable for piezoelectric and high temperature applications.     

Control of Microwave Dielectric Properties in the System BaO ⋅ Nd<Subscript>2</Subscript>O<Subscript>3</Subscript> ⋅ 4TiO<Subscript>2</Subscript>—BaO ⋅ Al<Subscript>2</Subscript>O<Subscript>3</Subscript> ⋅ 4TiO<Subscript>2</Subscript>

BaO ⋅ Nd₂O₃ ⋅ 4TiO₂—based ceramics were prepared by the mixed oxide route. Specimens were sintered at temperatures in the range 1200–1450^∘C. Microstructures were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM); microwave dielectric properties were determined at 3 GHz by the Hakki and Coleman method. Product densities were at least 95% theoretical. The addition of up to 1 wt% Al₂O₃ to the starting mixtures reduced the sintering temperatures by at least 100^∘C. Incorporation of small levels of Al into the structure (initially Ti sites) led to an increase in Q × f values, from 6200 to 7000 GHz, a decrease in relative permittivity (ε_r) from 88 to 78, and moved the temperature coefficient of resonant frequency (τ_f) towards zero. The addition of 0.5 wt% Al₂O₃ with 8 wt% Bi₂O₃ improved densification, increased both ε_r (to 88) and Q× f (to 8000 GHz) and moved τ_f closer to zero. Ceramics in the system (1 − x)BaO ⋅ Nd₂O₃ ⋅ 4TiO₂ + xBaO ⋅ Al₂O₃ ⋅ 4TiO₂ exhibited very limited solid solubility. The end member BaO ⋅ Al₂O₃ ⋅ 4TiO₂ was tetragonal in structure with the following dielectric properties: ε_r = 35; Q× f = 5000 GHz; τ_f = −15ppm/^∘C. Microstructures of the mixed Nd-Al compositions contained two distinct phases, Nd-rich needle-like grains and large Al-rich, lath-shaped grains. Products with near zero τ_f were achieved at compositions of approximately 0.14BaO ⋅ Nd₂O₃ ⋅ 4TiO₂ + 0.86BaO ⋅ Al₂O₃ ⋅ 4TiO₂, where Q× f = 8200 GHz and ε_r = 71.     

Evolution of ferroelectric and piezoelectric response by heat treatment in pseudocubic BiFeO<Subscript>3</Subscript>–BaTiO<Subscript>3</Subscript> ceramics

Heat treatment of ceramics is an important process to tailor the fine electromechanical properties. To explore the criteria for optimized heat treatment in a perovskite structure of (1–x)Bi_1.05FeO₃–xBaTiO₃ (BF–BT100x) system, the structural phase relation, ferroelectric and piezoelectric response of BF–BT36 and BF–BT40 ceramics prepared by furnace cooling (FC) and quenching process were investigated. The X-ray diffraction examination showed single pseudocubic perovskite structure for all the ceramics. The homogenous microstructure was obtained for all ceramics with relatively large grain size in the furnace cooled samples. Well saturated ferroelectric hysteresis loops and enhanced piezoelectric constant (d₃₃?=?97 pC/N) were achieved by quenching process. Dielectric curve of BF–BT36 showed large dielectric constant at its Curie temperature, however, BF–BT40 showed diffused relaxor-like dielectric anomalies. Quenched BF–BT36 samples showed typical butterfly like field induced strain curves, however negative strain decreased in BF–BT40 ceramics. From these investigated study, it is observed that BF–BT ceramics are very sensitive to the heat treatment process (furnace cooling and quenching) on the dielectric, electromechanical properties.     

Electrical and mechanical properties of MgO added 0.5Ba(Zr<Subscript>0.2</Subscript>Ti<Subscript>0.8</Subscript>)O<Subscript>3</Subscript>–0.5(Ba<Subscript>0.7</Subscript>Ca<Subscript>0.3</Subscript>)TiO<Subscript>3</Subscript> (BZT–0.5BCT) composite ceramics

MgO (0–2.0 vol%) added Ba(Zr_0.2Ti_0.8)O₃–0.5(Ba_0.7Ca_0.3)TiO₃ (BZT-0.5BCT) ceramics have been prepared by the conventional solid-state reaction method. The effects of MgO powder on the phase formation, densification, dielectric, piezoelectric and mechanical properties (flexural strength, hardness) of the BZT-0.5BCT ceramics have been studied systematically. The synthesized powder could be densified to 97 % of true density at a temperature of 1350 °C. The MgO addition also provided materials with better mechanical properties. The most interesting aspect of MgO added samples is their relative permittivity vs. temperature response. MgO additions effectively suppress the relative permittivity around phase transition temperature. The aging rate of d₃₃ observed for BZT-0.5BCT is 14 %/decade. MgO addition reduces the ageing rate and for 1 vol% MgO added, BZT-0.5BCT shows aging rate of 3 %/decade. BZT-0.5BCT/MgO ceramics possesses good mechanical properties viz., flexural strength 93 MPa, which is almost 25 % higher than that of monolithic BZT-0.5BCT (73 MPa).     

Structural,electrical, and multiferroic properties of Aurivillius Bi<Subscript>6</Subscript>Fe<Subscript>2</Subscript>(Ti<Subscript>3-x</Subscript>V<Subscript>x</Subscript>)O<Subscript>18+δ</Subscript> thin films prepared by chemical solution deposition

Aurivillius type five-layered V-doped Bi₆Fe₂(Ti_3-xV_x)O_18+δ (x = 0.00, 0.03, 0.06, and 0.09) thin films were prepared on Pt(111)/Ti/SiO₂/Si(100) substrates by using a chemical solution deposition method. All the thin films were crystallized in Aurivillius structures, which have been confirmed by using X-ray diffraction and Raman spectroscopy studies. On comparing the thin films, the Bi₆Fe₂(Ti_2.94V_0.06)O_18+δ thin film showed the most enhanced electrical and multiferroic properties, with a leakage current density value about four orders of magnitude lower than that of the Bi₆Fe₂Ti₃O₁₈ thin film, for example. All of these thin films showed anti-ferromagnetic hysteresis loops at room temperature. The significant decrease in the concentration of oxygen vacancies and the formation of a stable structure caused by doping with the donor V⁵⁺-ion are related to the improved properties in the V-doped Bi₆Fe₂(Ti_3-xV_x)O_18+δ thin films.     

Preparation and characterization of negative temperature coefficient (Ni,Mn)<Subscript>3</Subscript>O<Subscript>4</Subscript>–La(Mn,Ni)O<Subscript>3</Subscript> composite

The composites made of spinel-structured (Ni,Mn)₃O₄ and perovskite-structured La(Mn,Ni)O₃ were investigated for potential application as negative temperature coefficient (NTC) thermistor. The composites were prepared using the standard ceramic route. The electrical resistivity of the composite at 25°C was found to decrease by one to two orders of magnitude depending the amount of the low-resistivity perovskite phase, while the thermal constant determining the temperature sensitivity of the NTC thermistor was still reasonably large in the range of 4,000 to 3,000 K, and the resistivity drift after annealing at 150°C for 1,000 h in air was relatively small (∼1.2%). The general effective media model was adopted to fit the electrical resistivity data of the composites, giving a value of 0.37 for the percolation volume fraction of the perovskite phase. This work demonstrates that it is possible to tune the electrical resistivity and thermal constant of the spinel-structured oxide through making composite with low-resistivity perovskite-structured oxide.     

Partial Electronic Conductivity and Chemical Diffusivity of Li<Subscript>3<Emphasis Type="Italic">x</Emphasis></Subscript>La<Subscript>2/3−<Emphasis Type="Italic">x</Emphasis></Subscript>TiO<Subscript>3</Subscript> Solid Solution

Partial electronic conductivity and chemical diffusivity of Li have been measured on the system of Li_3xLa_2/3–xTiO₃ (LLT) with x = 0.13, a prospective Li⁺ electrolyte, against oxygen activity in the range of 10^–22 < a_O2 < 0.21 at 557, 610 and 663C, respectively by an ion-blocking polarization technique. It is found that the electronic conductivity of LLT, which in air is essentially an ionic conductor, varies as a_O2^–1/4 to render it mixed-conductive in reducing atmospheres, say, in a_O2 < 10^–12. The chemical diffusivity of component Li also increases from a value of the order of 10^–8 cm²/s in air atmosphere up to a maximum on the order of 10^–3 cm²/s as the electronic conductivity increases with decreasing oxygen activity. This is attributed to the variation of the electronic transference number and the thermodynamic factor with oxygen activity. The latter has been evaluated to be on the order of 10–10³.     

Microwave dielectric properties of (1-<Emphasis Type="Italic">x</Emphasis>) BiVO<Subscript>4</Subscript>–<Emphasis Type="Italic">x</Emphasis>Ln<Subscript>2/3</Subscript>MoO<Subscript>4</Subscript> (Ln=Er,Sm, Nd,la) ceramics with low sintering temperatures

A series of microwave dielectric ceramics of (1-x) BiVO₄ -xLn_2/3MoO₄ (Ln = Er, Sm, Nd and La; x = 0.06, 0.08, 0.10) sintered below 900 °C were prepared via solid-state reaction. As the x values increase, the monoclinic scheelite continuously changes to a tetragonal structure at x = 0.10. The incorporation of Ln_2/3MoO₄ into the BiVO₄ matrix increases the product (Q × f) of quality factor (Q) and resonance frequency (f), and temperature coefficient (τ _f ), but lowers the dielectric constant (ε _r). Microwave dielectric ceramics with low sintering temperatures (<900 °C) are obtained: ε _r of ~71.1, 81.6, 75.6 and ~75.3; Q × f values of ~8292, 5508, 8695 and 9043 GHz; τ _f of ~ ?51, 134, 149 and 158 ppm/°C, for 0.94BiVO₄–0.06Er_2/3MoO₄, 0.92BiVO₄–0.08Sm_2/3MoO₄, 0.9BiVO₄–0.1Nd_2/3MoO₄ and 0.9BiVO₄–0.1La_2/3MoO₄ ceramics, respectively. Moreover, (1-x) BiVO₄ -xLn_2/3MoO₄ (Ln = Er, Sm, Nd and La; x = 0.06, 0.08 and 0.10) ceramics are chemically compatible with both Ag and Cu powders at their sintering temperatures. The series of microwave dielectric ceramics might be potential candidates for low temperature co-fired ceramics (LTCC) technology applications.     

Effect of mechanical loading on the tuning of acoustic resonances in Ba<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Sr<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>TiO<Subscript>3</Subscript> thin films

The effect of mechanical loading on the tuning performance of a tunable Thin Film Bulk Acoustic Wave Resonator (TFBAR) based on a Ba_0.3Sr_0.7TiO₃ (BST) thin film has been investigated experimentally and theoretically. A membrane-type TFBAR was fabricated by means of micromachining. The mechanical load on the device was increased stepwise by evaporating SiO₂ on the backside of the membrane. The device was electrically characterized after each evaporation step and the results were compared to those obtained from modeling. The device with the smallest mechanical load exhibited a tuning of − 2.4% and − 0.6% for the resonance and antiresonance frequencies at a dc electric field of 615 kV/cm, respectively. With increasing mechanical load a decrease in the tuning performance was observed. This decrease was rather weak if the thickness of the mechanical load was smaller or comparable to the thickness of the active BST film. If the thickness of the mechanical load was larger than the thickness of the active BST layer, a significant reduction in the tuning performance was observed. The weaker tuning of the antiresonance frequency was due to a reduced tuning of the sound velocity of the BST layer with increasing dc bias. The resonance frequency showed a reduced tuning due to a decrease in the effective electromechanical coupling factor of the device with increasing mechanical load. With the help of the modeling we could de-embed the intrinsic tuning performance of a single, non-loaded BST thin film. We show that the tuning performance of the device with the smallest mechanical load we fabricated is close to the intrinsic tuning characteristics of the BST layer.     

Temperature Sensitive Properties of the La(Ti<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>)O<Subscript>3</Subscript> System

The electric mechanisms of perovskite-type LaMnO₃ was investigated with B-site substitution in this paper. Samples of La(Ti_xMn_{1 − x})O₃ (0.1 ≰ x ≰ 0.7) were sintered at different temperature. The voltage-temperature (V-T) curves of the samples were tested from room temperature (25^∘C) to 300^∘C, then the electric properties were measured and analyzed. The experimental results showed that the resistivity-temperature (ρ-T) curves of the samples matched NTC characteristic. The resistivity increased slightly with the increase of Ti amount as x was less than 0.5, however, it rose greatly after x exceeded 0.5; The sintering temperatures have a little influence on the resistivity, except for the sample with x = 0.7.     

Study of the pyroelectric behavior of BaTi<Subscript>1−<Emphasis Type="BoldItalic">x</Emphasis></Subscript>Sn<Subscript><Emphasis Type="BoldItalic">x</Emphasis></Subscript>O<Subscript>3</Subscript> piezo-ceramics

In this work, the thermal square wave method at single-frequency (TSWM) was applied to functionally graded BaTi_1−x Sn _x O₃ samples with a tin gradient of 0.075 ≤ x ≤ 0.15. The samples were fabricated by sintering of bi-, tri- and tetramorph green bodies. The polarization at the back side with a higher tin content was in opposite direction to the polarization of the surface with a lower tin content. This was attributed to the appearance of a space charge layer. The determined depth profiles of the pyroelectric coefficient illustrate the appearance of a nearly constant polarization in the region of lower tin concentration of tri- and tetramorph samples. The pyroelectric coefficient profiles were in good agreement with the averaged over sample thickness pyroelectric coefficient obtained separately by the quasistatic method.     

In-Plane 90<Superscript>∘</Superscript> Rotation of Lamellar Domains in PbTiO<Subscript>3</Subscript> Grains Revealed by Piezoresponse Force Microscopy

Nanoscale switching of the lamellar 90^∘ domains ({a-a} domains) of PbTiO₃ grains in the surface of sol-gel-derived PbTiO₃/Pb(Zr_0.58Ti_0.42)O₃/PbTiO₃ thin films is studied by three-dimensional piezoresponse force microscopy. It is demonstrated that the lamellar domain pattern in the PbTiO₃ grains can be rotated 90^∘ in the plane of film by the electric field at the tip. It is found that the rotation of lamellar domain pattern involves transverse growth of the existing embedded a-a domain nucleus, whose domain walls are perpendicular to the surrounding ones. During the transverse growth, the existing 90^∘ domains extend along length direction and penetrate into neighboring domain walls, while formation of new 90^∘ domain walls was mediated by the nanoscale 45^∘ tilted spike domains.     

Effect of sintering temperature on microstructure and piezoelectric properties of Pb-free BiFeO3–BaTiO3 ceramics in the composition range of large BiFeO3 concentrations

Lead-free (1-x)BiFeO₃–xBaTiO₃ [(1-x)BF-xBT] piezoelectric ceramics in the range of large BF concentrations were prepared by conventional oxide-mixed method at various sintering temperatures. The sintering temperatures have a significant effect on the microstructure of the ceramics, and the composition has a remarkable effect on optimal sintering temperature of the ceramics, which are closely related with piezoelectric properties. The grain size increased with increasing sintering temperature and the optimal sintering temperature increased with increasing BT content. The ceramics with x?=?0.275 sintered at 990 °C exhibit enhanced electrical properties of d ₃₃?=?136pC/N and k _p?=?0.312 due to the polarization rotation mechanisms at MPB and desired microstructure. These results show that the ceramic with x?=?0.275 is a promising lead-free high-temperature piezoelectric material.     

Synthesis,and measurement of structural and magnetic properties,of La<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>CoO<Subscript>3</Subscript> perovskite ceramic oxides

Perovskite-type Cd-doped LaCoO₃ materials were synthesized by a simple solution-based combustion process. The synthesized materials were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), diffuse reflectance (DR) in the UV-VIS, and magnetic property measurements. The parent LaCoO₃ compound showed spin-glass transition at low temperatures, and with progressive Cd doping, showed transition to paramagnetic ordering. The changes in magnetic properties of the materials are correlated to the changes in structural features resulting from the Rietveld structural refinement of the materials.     

Dielectric and piezoelectric properties of sodium lithium niobate Na1−x Li x NbO3 lead free ferroelectric ceramics

High density sodium lithium niobate lead free ceramics near the morphtropic phase boundary [Na _x Li_1?x NbO₃, (LNN), x?=?0.12] were prepared by the solid state reaction method. XRD patterns showed that the lattice structures were changed after polarization. The temperature dependence of the dielectric constant and dielectric loss, pyroelectric coefficient and DSC curves of LNN ceramics showed that there exist three phase transitions from room temperature up to the Curie temperature. The hysteresis loop and piezoelectric properties were measured and discussed.     

Electro-chemo-mechanical studies of perovskite-structured mixed ionic-electronic conducting SrSn<Subscript>1-x</Subscript>Fe<Subscript>x</Subscript>O<Subscript>3-x/2+δ</Subscript> Part III: Thermal and chemical expansion

The thermal and chemical expansion of a potential solid oxide fuel cell (SOFC) cathode material SrSn_0.65Fe_0.35O_{3–0.35/2+δ} (SSF35) were investigated to assess its thermo-chemo-mechanical stability at SOFC operating temperatures and to establish the correlation between defect concentrations (oxygen vacancies and electrons) and chemical expansion with the aid of the defect chemical model reported in part I of this study. Thermochemical expansion was measured as a function of temperature and oxygen partial pressure. The chemical expansion of SSF35 showed a strong correlation with changes in oxygen nonstoichiometry associated with changes in Fe valence state. Coefficients of both chemical (CCE) and thermal (CTE) expansion were calculated and found to be smaller than that of the closely related mixed conducting perovskite oxide SrTi_0.65Fe_0.35O_{3–0.35/2+δ} (STF35). The thermal expansion coefficient of SSF was found to be close to that of YSZ (most popular solid oxide electrolyte), which makes SSF35 more attractive in terms of overall thermo-chemical stability. The chemical expansion of SSF35 showed decreasing CCE with increasing temperature and decreasing CTE with increasing oxygen deficiency, both opposite to the trends observed for STF35. Distortion in symmetry from the cubic structure seems to be responsible for the smaller coefficients and increasing asymmetry with expansion seems accountable for opposite trends of CCE and CTE compared to the STF counterpart.