The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Catalytic behavior of La–Sr–Ce–Fe–O mixed oxidic/perovskitic systems for the NO+CO and NO+CH4+O2 (lean-NOx) reactions

Mixed oxides of the general formula La_0.5Sr_xCe_yFeO_z were prepared by using the nitrate method and characterized by XRD and Mössbauer techniques. The crystal phases detected were perovskites LaFeO₃ and SrFeO_3−x and oxides -Fe₂O₃ and CeO₂ depending on x and y values. The low surface area ceramic materials have been tested for the NO+CO and NO+CH₄+O₂ (“lean-NO_x”) reactions in the temperature range 250–550°C. A noticeable enhancement in NO conversion was achieved by the substitution of La³⁺ cation at A-site with divalent Sr⁺² and tetravalent Ce⁺⁴ cations. Comparison of the activity of the present and other perovskite-type materials has pointed out that the ability of the La_0.5Sr_xCe_yFeO_z materials to reduce NO by CO or by CH₄ under “lean-NO_x” conditions is very satisfying. In particular, for the NO+CO reaction estimation of turnover frequencies (TOFs, s⁻¹) at 300°C (based on NO chemisorption) revealed values comparable to Rh/-Al₂O₃ catalyst. This is an important result considering the current tendency for replacing the very active but expensive Rh and Pt metals. It was found that there is a direct correlation between the percentage of crystal phases containing iron in La_0.5Sr_xCe_yFeO_z solids and their catalytic activity. O₂ TPD (temperature-programmed desorption) and NO TPD studies confirmed that the catalytic activity for both tested reactions is related to the defect positions in the lattice of the catalysts (e.g., oxygen vacancies, cationic defects). Additionally, a remarkable oscillatory behavior during O₂ TPD studies was observed for the La_0.5Sr_0.2Ce_0.3FeO_z and La_0.5Sr_0.5FeO_z solids.     

η-Al2O3与γ-Al2O3在CS2催化水解反应中的性能比较

通过制备高纯度的前驱体湃铝石获得了η-Al₂O₃材料,采用XRD验证了η-Al₂O₃与γ-Al₂O₃在晶相结构上的差异,比较了两者的表面形貌、织构及酸碱性能,结果显示,η-Al₂O₃与γ-Al₂O₃的比表面积相当,但η-Al₂O₃具有更弱的弱碱位和较少的强碱位,并拥有丰富的中等强度酸性位。将η-Al₂O₃与γ-Al₂O₃作为催化剂应用于CS₂水解反应,结果表明,在(200~450) ℃测试温度范围内,η-Al₂O₃催化剂对CS₂的水解活性始终优于γ-Al₂O₃,两种催化剂上CS₂反应的浓度效应也明显不同,推测与它们的酸碱性质影响了对CS₂的吸附能力有关,导致两者催化CS₂水解反应遵循了不同的机制。     

Effect of rare-earth element oxides (La2O3, Ce2O3) on the structural and physico-chemical characteristics of Pd/Al2O3 monolithic catalysts of nitrogen oxide reduction by methane

It is shown that introduction of additives of rare-earth element oxides (La₂O₃, CeO₂) enables regulating the structural and functional characteristics of Pd/Al₂O₃-catalysts (applied on ceramic monoliths of honeycomb structure) of nitrogen oxide reduction by methane. Modifying additives provide increase of thermal stability of porous structure of both highly dispersed Al₂O₃, as the second support, and the catalyst as a whole.

Contribution of La₂O₃ and CeO₂ in increasing the thermal stability is of an additive nature, and lanthanum oxide shows the higher efficiency than cerium one. According to X-ray phase analysis data, stabilizing action is conditioned by occurrence of rare-earth element oxides into lattice of Al₂O₃, which retards diffusional processes leading to phase transitions of low-temperature crystalline modifications of alumina into high-temperature ones with a low specific surface. For the catalyst samples modified with La₂O₃ an effect of thermal activation is observed, which is revealed by increase in catalytic activity as a result of annealing at 850 °C. Such a phenomenon, as shown by means of X-ray photoelectron spectroscopy technique, can be explained via stabilization of palladium in singly charged state in the form of groups of Pd⁺O₂⁻ and corresponding increase in concentration of active centers.     

Performance of solvothermally prepared Ga2O3-Al2O3 catalysts for SCR of NO with methane

The solvothermal reaction of mixtures of aluminum isopropoxide (AIP) and gallium acetylacetonate (Ga(acac)₃) directly yielded the mixed oxides of γ-Ga₂O₃-Al₂O₃. In the solvothermal synthesis, the crystal structure of mixed oxides was controlled by the initial formation of γ-Ga₂O₃ nuclei. The mixed oxides prepared in diethylenetriamine have extremely high activities for selective catalytic reduction (SCR) of NO with methane as a reducing agent. With increasing crystallite size of the spinel structure, the catalytic activity increased. The ratio of the amount of methane consumed by combustion to total methane conversion was proportional to the density of acid sites on the surface of the mixed oxides. The mixed oxide catalysts prepared in diethylenetriamine had lower densities of acid sites and showed a higher methane-efficiency for CH₄-SCR than those prepared in other solvents. These catalysts maintained their high activity even when the reaction was carried out under the severe conditions (i.e., high space velocity and low NO concentration).     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Study of Ag/La0.6Sr0.4MnO3 catalysts for complete oxidation of methanol and ethanol at low concentrations

Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure were prepared by using a citric acid sol–gel method, and their catalytic performance for complete oxidation of methanol and ethanol was evaluated and compared with that of the γ-Al₂O₃-supported catalysts, Ag/γ-Al₂O₃, Pt/γ-Al₂O₃, and Pd/γ-Al₂O₃. The results showed that the Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure displayed the activity significantly higher than that of the supported precious metal catalysts, 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ in the temperature range of 370–573 K. Over a 6%Ag/20%La_0.6Sr_0.4MnO₃/γ-Al₂O₃ catalyst, the T₉₅ temperature for methanol oxidation can be as low as 413 K. Even at such low reaction temperature, there were little HCHO and CO detected in the reaction exit-gas. However, for the 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ catalysts, the HCHO content in the reaction exit-gas reached 200 and 630 ppm at their T₉₅ temperatures. Over a 6%Ag/La_0.6Sr_0.4MnO₃ catalyst, the T₉₅ temperature for ethanol oxidation can be as low as 453 K, with a corresponding content of CH₃CHO in the exit-gas at 782 ppm; when ethanol oxidation is performed at 493 K, the content of acetaldehyde in the exit-gas can be below 1 ppm. Characterization of the catalysts by X-ray diffraction (XRD), TEM, XPS, laser Raman spectra (LRS), hydrogen temperature-programmed reduction (H₂-TPR) and oxygen temperature-programmed desorption (O₂-TPD) methods revealed that both the surface and the bulk phase of the perovskite La_0.6Sr_0.4MnO₃ played important roles in the catalytic oxidation of the alcohols, and that γ-Al₂O₃ as the bottom carrier could be beneficial in creating a large surface area of catalyst. Moreover, a small amount of Ag⁺ doped onto the surface of La_0.6Sr_0.4MnO₃ was able to partially occupy the positions of La³⁺ and Sr²⁺ due to their similar ionic radii, and thus, became stabilized by the perovskite lattice, which would be in favor of preventing the aggregation of the Ag species on the surface and enhancing the stability of the catalyst. On the other hand, modification of the Ag⁺ to the surface of La_0.6Sr_0.4MnO₃ resulted in an increase in relative content of the surface O₂²⁻/O⁻ species highly reactive toward the alcohols and aldehydes as well as CO. Besides, solution of low-valence metal oxides SrO and Ag₂O with proper amounts in the lattice of the trivalent metal perovskite-type oxide LaMnO₃ would also lead to an increase in the content of the reducible Mnⁿ⁺ and the formation of anionic vacancies, which would be favorable for the adsorption-activation of oxygen on the functioning catalyst and the transport of the lattice and surface oxygen species. All these factors would contribute to the pronounced improvement of the catalyst performance.     

Preparation and structural characterization of Co/Al2O3 catalysts for the ozonation of pyruvic acid

A series of Co/Al₂O₃ catalysts were prepared by the incipient wetness impregnation method using γ-Al₂O₃ support and (CH₃COO)₂Co·4H₂O solutions, followed by calcination at 500–800 °C. Characterization of catalysts was accomplished by several techniques such as thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), physisorption of nitrogen, mercury and helium-based pycnometries, Fourier transform-infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and pH of zero charge (PZC). Impregnation of support produced a moderate decrease of its surface area and pore volume and also led to minor changes of its PZC. Depending on preparation conditions (i.e., calcination atmosphere and temperature and metal loading), one or more of the following Co-containing compounds were identified: CoO, Co₃O₄ and CoAl₂O₄. The support and prepared Co/Al₂O₃ catalysts were tested to catalyze the ozonation of aqueous pyruvic acid at pH 2.5. Pyruvic acid was shown refractory towards single ozonation but the use of γ-Al₂O₃ and Co/Al₂O₃ catalysts resulted in 56–96% pyruvic acid conversion and 41–78% decrease in DOC after 2 h of ozonation of phosphate-buffered solutions. In the absence of the buffer, conversion rate was enhanced likely as a result of pH increase during the course of the process thus giving rise to the indirect way of ozonation through hydroxyl radicals. Acetic acid was found as the main by-product of pyruvic acid ozonation. Depending on the catalyst used, yield of acetic acid varied from 32 to 49%, values noticeably lower that that obtained from the control non-catalytic ozonation experiment (73%). Differences in catalytic activity amongst the various Co/Al₂O₃ catalysts investigated were attributed to the different Co active phases deposited on the γ-Al₂O₃ surface. The following sequence of increasing activity can be inferred from experimental results: CoO, CoAl₂O₄ and Co₃O₄. All the Co/Al₂O₃ catalysts prepared showed good stability as the percentage of cobalt leached out was rather low.     

Effect of the order of potassium introduction on the texture and activity of Mo/Al2O3 catalysts in water gas shift reaction

The effect of deposition and order of potassium introduction on the texture and activity of Mo/γ-Al₂O₃ catalysts in water gas shift (WGS) reaction was investigated. The samples were synthesised by incipient wetness impregnation of the carrier with aqueous solutions of the corresponding salts followed by drying and calcination after each deposition step. The prepared catalyst precursors were sulphided at 400°C for 2 h with 6% H₂S in H₂ before testing in WGS reaction in a glass flow apparatus at 400°C under atmospheric pressure.

The results show that potassium deposition alone on the bare γ-Al₂O₃ (sample K/Al₂O₃) decreases the specific surface after calcination by blocking the constrictions between the pores in the primary porous texture. In the WGS reaction conditions part of the pores are deblocked and a redistribution in the pore volumes occurs.

The deposition of the Mo (sample Mo/Al₂O₃) also results in a decrease in both specific surface and total pore volume with respect to the bare support. However after catalytic activity test no substantial changes in its texture were observed.

The addition of K to the Mo (sample KMo/Al₂O₃) leads to nonuniformity in distribution of molybdenum–oxygen entities due to partial migration of the MoO_x species to the external surface. The specific surface is not changed during the reaction test.

The deposition of Mo on K/Al₂O₃ contributes to the uniform distribution of oxomolybdenum species in the porous texture of the support. This uniformity is preserved to a high extent in the catalytic reaction as well. The activity in the synthesised samples in the WGS reaction decreases in the order MoK/Al₂O₃ > Mo/Al₂O₃ > KMo/Al₂O₃.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Characteristics of La2O3 thin films deposited using metal organic chemical vapor deposition with different oxidant gas

La₂O₃ films were deposited using O₃ and the structural and electrical properties were investigated and compared with those of La₂O₃ films deposited using O₂. The deposition temperature of the La₂O₃ films using O₃ was slightly reduced compared to that of the La₂O₃ films generated using O₂. After a post-annealing process at 600 and 900 °C, the crystallinity of the La₂O₃ films using O₃ were smaller than that using O₂. The leakage current density increased after annealing at 600 °C due to densification and then decreased after annealing at 900 °C due to interfacial layer growth. The effective dielectric constant of the La₂O₃ films deposited using O₃ decreased at 900 °C due to interfacial layer growth. The La₂O₃ films deposited using O₃ showed better structural and electrical properties in this study.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

Optimal promotion by rubidium of the CO + NO reaction over Pt/γ-Al2O3 catalysts

The reduction of NO by CO over Rb-promoted Pt/γ-Al₂O₃ catalysts has been investigated over a wide range of temperature (ca. 200–500°C), partial pressures of reactants and promoter loadings. For purposes of comparison, K- and Cs-promoted Pt/γ-Al₂O₃ catalysts were tested under the same conditions. Rubidium strongly enhanced both catalytic activity and N₂-selectivity. Rate increases by factors as high as 110 and 45 for the production of N₂ and CO₂, respectively, relative to unpromoted Pt were obtained, accompanied by substantial increase in N₂-selectivity (e.g. from 24 to 82% at 350°C and [CO]=0.5%, [NO]=1%). Under stoichiometric conditions, Rb-promoted catalysts gave 100% conversion of both reactants with 100% selectivity towards N₂ at T350°C and at an effective reactant contact time of only 0.5 s. In contrast, under the same conditions unpromoted Pt delivered <30% conversion and poor N₂-selectivity (approximately <40%); even at 480°C the conversion was only 60%. The observed promotional effects are ascribed to alkali-induced changes in the chemisorption bond strengths of CO, NO and NO dissociation products which lead to the observed activity enhancement and dependence of N₂-selectivity on promoter loading. The effects of K-promotion mirror those of Rb-promotion, but are significantly less pronounced. Rb is the best alkali promoter.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Quantification of the in situ DRIFT spectra of Pt/K/γ-A12O3 NOx adsorber catalysts

A method to quantify DRIFT spectral features associated with the in situ adsorption of gases on a NO_x adsorber catalyst, Pt/K/Al₂O₃, is described. To implement this method, the multicomponent catalyst is analysed with DRIFT and chemisorption to determine that under operating conditions the surface comprised a Pt phase, a pure γ-Al₂O₃ phase with associated hydroxyl groups at the surface, and an alkalized-Al₂O₃ phase where the surface –OH groups are replaced by –OK groups. Both DRIFTS and chemisorption experiments show that 93–97% of the potassium exists in this form. The phases have a fractional surface area of 1.1% for the 1.7 nm-sized Pt, 34% for pure Al₂O₃ and 65% for the alkalized-Al₂O₃. NO₂ and CO₂ chemisorption at 250 °C is implemented to determine the saturation uptake value, which is observed with DRIFTS at 250 °C. Pt/Al₂O₃ adsorbs 0.087 μmol CO₂/m²and 2.0 μmol NO₂/m², and Pt/K/Al₂O₃ adsorbs 2.0 μmol CO₂/m²and 6.4 μmol NO₂/m². This method can be implemented to quantitatively monitor the formation of carboxylates and nitrates on Pt/K/Al₂O₃ during both lean and rich periods of the NO_x adsorber catalyst cycle.     

Processing of hot pressed Al2O3–Cr2O3/Cr-carbide nanocomposite prepared by MOCVD in fluidized bed

Nanosized particles dispersed uniformly on Al₂O₃ particles were prepared from the decomposition of precursor Cr(CO)₆ by metal organic chemical vapor deposition (MOCVD) in a fluidized chamber. These nanosized particles consisted of Cr₂O₃, CrC_1−x, and C. A solid solution of Al₂O₃–Cr₂O₃ and an Al₂O₃–Cr₂O₃/Cr₃C₂ nanocomposite were formed when these fluidized powders were pre-sintered at 1000 and 1150 °C before hot-pressing at 1400 °C, respectively. In addition, an Al₂O₃–Cr₂O₃/Cr-carbide (Cr₃C₂ and Cr₇C₃) nanocomposite was formed when the particles were directly hot pressed at 1400 °C. The interface between Cr₃C₂ and Al₂O₃ is non-coherent, while the interface between Cr₇C₃ and Al₂O₃ is semi-coherent.     

Catalytic reduction of NO by CO over NiO/CeO2 catalyst in stoichiometric NO/CO and NO/CO/O2 reaction

A new catalyst composed of nickel oxide and cerium oxide was studied with respect to its activity for NO reduction by CO under stoichiometric conditions in the absence as well as the presence of oxygen. Activity measurements of the NO/CO reaction were also conducted over NiO/γ-Al₂O₃, NiO/TiO₂, and NiO/CeO₂ catalysts for comparison purposes. The results showed that the conversion of NO and CO are dependent on the nature of supports, and the catalysts decreased in activity in the order of NiO/CeO₂ > NiO/γ-Al₂O₃ > NiO/TiO₂. Three kinds of CeO₂ were prepared and used as support for NiO. They are the CeO₂ prepared by (i) homogeneous precipitation (HP), (ii) precipitation (PC), and (iii) direct decomposition (DP) method. We found that the NiO/CeO₂(HP) catalyst was the most active, and complete conversion of NO and CO occurred at 210 °C at a space velocity of 120,000 h⁻¹. Based on the results of surface analysis, a reaction model for NO/CO interaction over NiO/CeO₂ has been proposed: (i) CO reduces surface oxygen to create vacant sites; (ii) on the vacant sites, NO dissociates to produce N₂; and (iii) the oxygen originated from NO dissociation is removed by CO.     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.