Radiance Temperatures (in the Wavelength Range 530 to 1500 nm) of Nickel at Its Melting Point by a Pulse-Heating Technique

The radiance temperatures (at seven wavelengths in the range 530 to 1500 nm) of nickel at its melting point were measured by a pulse-heating technique. The method is based on rapid resistive self-heating of the specimen from room temperature to its melting point in less than 1 s and on simultaneously measuring specimen radiance temperatures every 0.5 ms. Melting of the specimen was manifested by a plateau in the radiance temperature-versus-time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for nickel, as determined by averaging the results at each wavelength for 25 specimens, are: 1641 K at 530 nm, 1615 K at 627 nm, 1606 K at 657 nm, 1589 K at 722 nm, 1564 K at 812 nm, 1538 K at 908 nm, and 1381 K at 1500 nm. Based on uncertainties arising from pyrometry and specimen conditions, the combined uncertainty (two standard-deviation level) is about ± 6 K for the reported values in the range 530 to 900 nm and is about ± 8 K for the reported value at 1500 nm.     

Radiance temperatures (in the wavelength range 522–906 nm) of niobium at its melting point by a pulse-heating technique

Radiance temperatures (at six wavelengths in the range 522–906 nm) of niobium at its melting point were measured by a pulse-heating technique. The method is based on rapid resistive self-heating of the specimen from room temperature to its melting point in less than 1 s and on simultaneously measuring the specimen radiance temperatures every 0.5 ms with a high-speed multiwavelength pyrometer. Melting was manifested by a plateau in the radiance temperatureversus-time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength (standard deviation of an individual temperature from the mean: 0.1–0.4 K). The melting-point radiance temperatures for niobium were determined, by averaging the results at each wavelength for 10 specimens (standard deviation: 0.3 K), as follows: 2497 K at 522 nm, 2445 K at 617 nm, 2422 K at 653 nm, 2393 K at 708 nm, 2337 K at 809 nm, and 2282 K at 906 nm. Based on estimates of the random and systematic errors arising from pyrometry and specimen conditions, the total error in the reported values is about 5 K at 653 nm and 6 K at the other wavelengths.Paper presented at the Second Workshop on Subsecond Thermophysics, September 20–21, 1990, Torino, Italy.     

Radiance Temperatures (in the Wavelength Range 527 to 1500 nm) of Palladium and Platinum at Their Melting Points by a Pulse-Heating Technique

The radiance temperatures (at seven wavelengths in the range 527 to 1500 nm) of palladium and platinum at their respective melting points were measured by a pulse-heating technique. The method, based on rapid resistive self-heating of a specimen from room temperature to its melting point in less than 1 s, used two high-speed pyrometers to measure specimen radiance temperatures every 0.5 ms during the heating and melting period. Melting was manifested by a plateau in the radiance temperature-versus-time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for each metal as determined by averaging the results for several specimens at each wavelength are as follows. Based on uncertainties arising from pyrometry and specimen conditions, the expanded uncertainty (two-standard deviation level) is about ±7 K for the reported values in the range 527 to 900 nm and about ±8 K for the reported values at 1500 nm.     

Radiance Temperatures (in the Wavelength Range 521 to 1500 nm) of Rhenium and Iridium at Their Melting Points by a Pulse-Heating Technique

The melting-point radiance temperatures (at seven wavelengths in the range 521 to 1500 nm) of rhenium and iridium were measured by a pulse-heating technique. The method is based on rapid resistive self-heating of the specimen from room temperature to its melting point in less than 1 s and on simultaneously measuring the specimen radiance temperature every 0.5 ms with two high-speed pyrometers. Melting was manifested by a plateau in the radiance temperature-versus-time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for each metal were determined by averaging results for several specimens at each wavelength. The results are as follows. Based on estimates of the random and systematic errors arising from pyrometry and specimen conditions, the expanded uncertainty (two standard-deviation level) in the reported values is ±8K.     

Radiance temperatures (in the wavelength range 525 to 906 nm) of vanadium at its melting point by a pulse-heating technique

The radiance temperatures (at six wavelengths in the range 525 to 906 nm) of vanadium at its melting point were measured by a pulse-heating technique. The method is based on rapid resistive self-heating of the specimen from room temperature to its melting point in less than 1 s and on simultaneously measuring the specimen radiance temperatures every 0.5 ms with a high-speed six-wavelength pyrometer. Melting was manifested by a plateau in the radiance temperature-vs-time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for vanadium as determined by averaging the results at each wavelength for 16 specimens (standard deviation in the range 0.3 to 0.4 K. depending on the wavelength) are 2030 K at 525 nm, 1998 K at 622 nm, 1988 K at 652 nm, 1968 K at 714 nm, 1935 K at 809 nm, and 1900 K at 906 nm. Based on estimates of the random and systematic errors that arise from pyrometry and specimen conditions, the resultant uncertainty (2 SD level) in the reported values is about ±7 K at each wavelength.     

Radiance temperatures (in the wavelength range 523–907 nm) of group IVB transition metals titanium,zirconium, and hafnium at their melting points by a pulse-heating technique

The melting-point radiance temperatures (at six wavelengths in the range 523–907 nm) of the Group IVB transition metals titanium, zirconium, and hafnium were measured by a pulse-heating technique. The method is based on rapid resistive self-heating of the specimen from room temperature to its melting point in less than 1 s and on simultaneously measuring the specimen radiance temperatures every 0.5 ms with a high-speed six-wavelength pyrometer. Melting was manifested by a plateau in the radiance temperature-versus-time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for each metal were determined by averaging results for several specimens at each wavelength as follows: Based on estimates of the random and systematic errors arising from pyrometry and specimen conditions, the combined uncertainty (95% confidence level) in the reported values is about ±8K at each wavelength.     

Radiance temperatures (in the wavelength range 519–906 nm) of tungsten at its melting point by a pulse-heating technique

Radiance temperatures (at six wavelengths in the range 519–906 nm) of tungsten at its melting point were measured by a pulse-heating technique. The method is based on rapid resistive self-heating of the specimen from room temperature to its melting point in less than 1 s; and on simultaneously measuring the specimen radiance temperatures every 0.5 ms with a high-speed six-wavelength pyrometer. Melting was manifested by a plateau in the radiance temperature versus time function for each wavelength. The melting-point radiance temperatures for a given specimen were determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for tungsten were determined by averaging the results at each wavelength for 10 specimens (standard deviation in the range 0.5–1.1 K, depending on the wavelength) as follows: 3319 K at 519 nm, 3236 K at 615 nm, 3207 K at 652 nm, 3157 K at 707 nm, 3078 K at 808 nm, and 2995 K at 906 nm. Based on estimates of the random and systematic errors arising from pyrometry and specimen conditions, the total uncertainty in the reported values is about ±7 K at 653 nm and ± 8 K at the other wavelengths.Paper presented at the Third Workshop on Subsecond Thermophysics, September 17–18, 1992, Graz, Austria.     

Radiance Temperatures and Normal Spectral Emittances (in the Wavelength Range of 1500 to 5000 nm) of Tin, Zinc, Aluminum, and Silver at Their Melting Points by a Pulse-Heating Technique

The radiance temperatures at four wavelengths (in the range of 1500 to 5000 nm) of tin, zinc, aluminum, and silver at their respective melting points were measured by a pulse-heating technique using a high-speed fiber-coupled four-wavelength infrared pyrometer. The method is based on rapid resistive self-heating of a sample from room temperature to its melting point in less than 1 s while measuring the radiance emitted by it in four wavelength bands as a function of time. A plateau in the recorded radiance-versus-time traces indicates melting of the sample. The melting-point radiance temperatures for a given sample are determined by averaging the measured temperatures along the plateau at each wavelength. The melting-point radiance temperatures for each metal are, in turn, determined by averaging results for several samples. The normal spectral emittances at the melting transition of each metal are derived from the measured radiances at each wavelength and the published values of the thermodynamic (true) melting temperatures.     

Radiance temperatures (at 658 and 898 nm) of niobium at its melting point

Radiance temperatures (at 658 and 898 nm) of niobium at its melting point were measured by a pulse-heating technique. A current pulse of subsecond duration was imparted to a niobium strip and the initial part of the melting plateau was measured by high-speed pyrometry. Experiments were performed with two techniques and the results do not indicate any dependence of radiance temperature (at the melting point) on initial surface or system operational conditions. The average radiance temperature at the melting point of niobium is 2420 K at 658 nm and 2288 K at 898 nm, with a standard deviation of 0.4 K at 658 nm and 0.3–0.6 K at 898 nm (depending on the technique used). The total uncertainty in radiance temperature is estimated to be not more than ±6 K. The results are in good agreement with earlier measurements at the National Institute of Standards and Technology (USA) and confirm that both radiance temperature and normal spectral emissivity (of niobium at its melting point) decrease with increasing wavelength in the region 500–900 nm.Paper presented at the Third Workshop on Subsecond Thermophysics, September 17–18, 1992, Graz, Austria.     

Radiance Temperature and Normal Spectral Emittance (in the Wavelength Range of 1.5 to 5 μm) of Nickel at its Melting Point by a Pulse-Heating Technique

The radiance temperature of nickel at its melting point was measured at four wavelengths (in the nominal range of 1.5 to 5 μm) by a pulse-heating technique using a high-speed fiber-coupled four-channel infrared pyrometer. The method was based on rapid resistive self-heating of a specimen from room temperature to its melting point in less than 1 s while simultaneously measuring the radiance emitted by it in four spectral bands as a function of time. A plateau in the recorded radiance-versus-time traces indicated melting of the specimen. The melting-point radiance temperature for a given specimen was determined by averaging the temperature measured along the plateau at each wavelength. The results for several specimens were then, in turn, averaged to yield the melting-point radiance temperature of nickel, as follows: 1316 K at 1.77 μm, 1211 K at 2.26 μm, 995 K at 3.48 μm, and 845 K at 4.75 μm. The melting-point normal spectral emittance of nickel at these wavelengths was derived from the measured radiance in each spectral band using the published value of the thermodynamic (true) melting temperature of nickel.     

Hemispherical Total Emissivity of Niobium, Molybdenum, and Tungsten at High Temperatures Using a Combined Transient and Brief Steady-State Technique

The hemispherical total emissivity of three refractory metals, niobium, molybdenum, and tungsten, was measured with a new method using a combined transient and brief steady-state technique. The technique is based on rapid resistive self-heating of a solid cylindrical specimen in vacuum up to a preset high temperature in a short time (about 200 ms) and then keeping the specimen at that temperature under steady-state conditions for a brief period (about 500ms) before switching off the current through the specimen. Hemispherical total emissivity is determined at the temperature plateau from the data on current through the specimen, the voltage drop across the middle portion of the specimen, and the specimen temperature using the steady-state heat balance equation based on the Stefan–Boltzmann law. Temperature of the specimen is determined from the measured surface radiance temperature and the normal spectral emissivity; the latter is obtained from laser polarimetric measurements. Experimental results on the hemispherical total emissivity of niobium (2000 to 2600 K), molybdenum (2000 to 2700 K), and tungsten (2000 to 3400 K) are reported.     

Application of High-Speed Laser Polarimetry to Noncontact Detection of Phase Transformations in Metals and Alloys at High Temperatures

A high-speed laser polarimetry technique, developed recently for the measurement of normal spectral emissivity of materials at high temperatures, was used to detect solid–solid and solid–liquid phase transformations in metals and alloys in millisecond-resolution pulse-heating experiments. Experiments were performed where normal spectral emissivity at 633 nm was measured simultaneously with surface radiance temperature, resistance, and/or voltage drop across the specimen. It was observed that a phase transformation, as indicated either by an arrest in the specimen radiance temperature or changes in the resistance and/or voltage drop, generally caused a change in normal spectral emissivity. Experiments were conducted on cobalt, iron, hafnium, titanium, and zirconium to detect solid–solid phase transformations. Similar experiments were also performed on niobium, titanium, and the alloy 85titanium–15molybdenum (mass%) to detect solid–liquid phase transformations (melting).     

A transient (subsecond) technique for measuring heat of fusion of metals

A transient technique is described for measuring the heats of fusion of metals with melting temperatures above 1500 K. The specimen configuration consists of a strip of the metal under study sandwiched between two strips of another metal with a higher melting temperature. The basic method consists of rapidly heating the composite specimen by passing a subsecond-duration electrical current pulse through it and simultaneously measuring the radiance temperature of the containment metal surface, as well as the current through and voltage drop across the specimen. The melting of the metal under study is manifested by a plateau in the temperature versus time function for the containing metal surface. The time integral of the power absorbed by the specimen during melting yields the heat of fusion. Measurements on several tantalum-niobium-tantalum specimens yield a value of 31.5 kJ · mor^–1 for the heat of fusion of niobium, with an estimated maximum inaccuracy of ± 5%.     

Normal Spectral Emissivity of Niobium (at 900 nm) by a Pulse-Heating Reflectometric Technique

The normal spectral emissivity of niobium strip specimens was measured using a new pulse-heating reflectometric technique. The hemispherical spectral reflectivity of the surface of a strip tangent to an integrating sphere is determined by a high-speed lock-in technique. At the same time, the radiance temperature of the strip is measured by high-speed pyrometry from approximately 1000K to the melting point. Details of the measurement method and of the related calibration techniques are reported. Results of the normal spectral emissivity of niobium at 900 nm from room temperature to its melting point are presented, discussing differences related to the heating rate and to surface conditions.     

A dynamic technique for measuring normal spectral emissivity of electrically conducting solids at high temperatures with a high-speed spatial scanning pyrometer

A dynamic (subsecond) technique is described for measuring normal spectral emissivity of electrically conducting solids at high temperatures, primarily in the range 1800 K up to near their melting point. The basic method involves resistively heating a tubular specimen from ambient temperature through the temperature range of interest in less than 1 s by passing an electrical current pulse through it, while using a high-speed spatial scanning pyrometer to measure spectral radiance temperatures along a 25-mm length on the specimen. This portion of the specimen includes a small rectangular hole that approximates a blackbody cavity. Measurements of spectral radiance temperature of the specimen surface as well as specimen true temperature enable the determination of the normal spectral emissivity of the surface via Planck's law. The applicability of the technique is demonstrated by measurements performed on molybdenum in the range 1900–2850 K.     

A Multiwavelength Reflectometric Technique for Normal Spectral Emissivity Measurements by a Pulse-Heating Method

A new technique has been developed for the direct measurement of the normal spectral emissivity at several wavelengths in pulse-heating conditions, adding some novel features to previous versions of this type of apparatus. Pulse-heating experiments were performed on niobium strip specimens, taking the specimen from room temperature to the melting point using rapid resistive self-heating. The normal spectral emissivity was measured at three wavelengths by a multi-wavelength reflectometric technique. At the same time, the radiance temperature was measured at the same wavelengths by a high-speed pyrometer from approximately 1100 K to the melting point. Details of the method, the measurement apparatus, and the calibration technique are described. Preliminary results for the normal spectral emissivity of niobium at 633, 750, and 900 nm over a wide temperature range are presented.     

Radiance temperature (at 653 nm) of tungsten at its melting point

The radiance temperature (at 653 nm) of tungsten at its melting point was measured using a subsecond-duration pulse-heating technique. Specimens in the form of strips with initially different surface roughnesses were used. The results do not indicate any dependence of radiance temperature (at the melting point) on initial surface or system operational conditions. The average radiance temperature (at 653 nm) at the melting point for 23 tungsten specimens is 3208 K on IPTS-68, with a standard deviation of 0.8 K and a maximum absolute deviation of 1.9 K. The total error in the radiance temperature is estimated to be not more than ± 10 K.     

A microsecond-resolution transient technique for measuring the heat of fusion of metals: Niobium

A microsecond-resolution pulse-heating technique is described for the measurement of the heat of fusion of refractory metals. The method is based on rapid resistive self-heating of the specimen by a high-current pulse from a capacitor discharge system and measurement of the current through the specimen, the voltage across the specimen, and the radiance temperature of the specimen as a function of time. Melting of the specimen is manifested by a plateau in the temperature versus time function. The time integral of the power absorbed by the specimen during melting yields the heat of fusion. Measurements gave a value of 31.1 kj · mol^–1 for the heat of fusion of niobium, with an estimated maximum uncertainty of ±5%. Electrical resistivity of solid and liquid niobium at its melting temperature was also measured.     

Measurement of Melting Point and Radiance Temperature (at Melting Point and at 653 nm) of Hafnium-3 (wt. %) Zirconium by a Pulse Heating Method

A subsecond duration pulse heating method is used to measure the melting point and radiance temperature (at 653 nm) at the melting point of hafnium containing 3.12 weight percent zirconium. The results yield a value of 2471 K for the melting point on the International Practical Temperature Scale of 1968. The radiance temperature (at 653 nm) of this material at its melting point is 2236 K, and the corresponding normal spectral emittance is 0.39. Estimated inaccuracies are: 10 K in the melting point and in the radiance temperature, and 5 percent in the normal spectral emittance.