Miscibility and interactions in poly(methylthiomethyl methacrylate)/poly(vinyl alcohol) blends

Poly(methylthiomethyl methacrylate) (PMTMA) is miscible with poly(vinyl alcohol) (PVA) over the whole composition range as shown by the existence of a single glass transition temperature in each blend. The interaction between PMTMA and PVA was examined by Fourier transform infrared spectroscopy, solid-state nuclear magnetic resonance spectroscopy and X-ray photoelectron spectroscopy. The interactions mainly involve the hydroxyl groups of PVA and the thioether sulfur atoms of PMTMA, and the involvement of the carbonyl groups of PMTMA in interactions is not significant. The measurements of proton spin-lattice relaxation time reveal that PMTMA and PVA do not mix intimately on a scale of 1-3 nm, but are miscible on a scale of 20-30 nm. In comparison, we have previously found that PMTMA is miscible with poly(p-vinylphenol) and the two polymers mix intimately on a scale of 1-3 nm.     

Grafting and adsorption of poly(vinyl) alcohol in vinyl acetate emulsion polymerization

Poly(vinyl alcohol) is often used in vinyl acetate emulsion polymerization as a protective colloid, but its role is complex and controversial since it partakes in grafting reactions with the monomer, influencing process mechanisms, and affecting the colloidal properties of the latex. Furthermore, in industrial operations, the wide scatter of macromolecular properties of the commercial types of poly(vinyl alcohol) causes process irreproducibilities. In this work different types of polyvinyl alcohol were used to perform a series of polymerizations, and their kinetics were compared. A selective solubilization procedure was applied to separate the three fractions of poly(vinyl alcohol) in the final latex: free in the water phase, physically adsorbed onto the polymer particles and chemically grafted. These results were compared with those obtained from pure adsorption measurements of polyvinyl alcohol onto ‘emulsifier-free’ polyvinyl acetate dispersions. The rheological behavior of the different latexes was also compared, and the results were used to formulate an hypothesis on the interaction mechanisms acting in these systems.     

Synthesis and characterization of hydrophobically modified poly(vinyl alcohol) hydrogel membrane

Hydrophobically modified poly(vinyl alcohol), [PVA] was synthesized by graft copolymerization of N-tertiary butyl acrylamide [NTBA] onto PVA by free radical polymerization. The incorporation of NTBA onto PVA chains was confirmed by elemental analysis, FT-IR and NMR spectroscopy. A series of graft copolymers with different contents of NTBA were prepared and membranes were casted from these copolymer solutions in dimethyl sulfoxide. The increase in hydrophobicity with an increase in NTBA content was investigated by contact angle measurements. The swelling behaviour of membranes as a function of temperature, hydrophobic content, annealing temperature and period was studied. Permeability of solutes through these membranes was investigated as a function of solute size, membrane hydrophobicity and temperature. The swelling behaviour of the copolymer membranes showed that the lower content of NTBA gives discontinuous volume transition with respect to temperature whereas, the presence of higher amounts of NTBA showed decreased swelling ratios with very little influence of temperature on the swelling. The permeabilities of solutes through these membranes were strongly dependent on the size of the solute, solution temperature and hydrophobicity of the membrane. The copolymer membranes were further characterized using DSC, DMA and XRD. The peak becomes broader as the NTBA content increases.     

Drying of semicrystalline polymers: mathematical modeling and experimental characterization of poly(vinyl alcohol) films

A mathematical model was developed to predict the drying mechanism of semicrystalline polymers involving multiple solvents. Since drying of semicrystalline polymers can be accompanied by changes in polymer degree of crystallinity, the model integrates crystallization kinetics and the Vrentas-Duda diffusion model to provide a better understanding of the mechanism. The model considers the effect of external conditions such as temperature, film shrinkage and diffusion and evaporation of multiple solvents during drying. Poly(vinyl alcohol) (PVA)/water/methanol was chosen as a test system. The drying kinetics of PVA films swollen in water and methanol were investigated using gravimetric techniques. The model predicts that higher temperatures, lower film thicknesses and lower methanol to water ratios increase the drying rate. The model predictions were compared with experimental data and showed good agreement.     

Compression of poly(vinyl alcohol) gels by ultracentrifugal forces

Compression due to ultracentrifugal forces was investigated for poly(vinyl alcohol) (PVA) gels. The concentration gradient profiles for the gels were obtained by experiment and were then compared with a theoretical prediction. By the application of the centrifugal forces, the concentration gradient near the bottom increases sharply whereas the gradient inside the gel remains almost constant in the region far from the bottom. Further application of the centrifugal forces enhances the peak near the bottom. These are well explained by the theory proposed in the previous paper [Urayama et al. J Chem Phys 2005;122:024906.]. The frictional coefficient f for the PVA gels, which originates from the friction between the polymer network and solvent molecules, is estimated to be 3.5×10¹⁴ N s m⁻⁴.     

Degree of crosslinking and mechanical properties of crosslinked poly(vinyl alcohol) beads for use in solid-phase organic synthesis

The limited swellability in polar media of the commonly used polystyrene/divinylbenzene (PS-DVB) support materials for solid-phase organic synthesis has led to the development of novel, highly swellable hydrophilic gels designed for use in aqueous or polar media. Poly(vinyl alcohol) beads crosslinked with epichlorohydrin (PVA-EP) were prepared by a two-step inverse-suspension polymerization method. While it is known that the morphology of the resulting beads can be controlled by the ratio of EP versus PVA as well as by the pre-crosslinking time, the actual degree of crosslinking of the beads and their mechanical properties remain unknown. It is therefore the purpose of this study to evaluate the actual degree of crosslinking of beads prepared with different quantities of crosslinker in the feed by spectroscopic (Raman, nuclear magnetic resonance) and chemical (functional group loading) methods. The mechanical properties of these swollen PVA-EP beads will be evaluated by single-bead unconfined compression in solvents such as water, N,N-dimethylformamide (DMF), and tetrahydrofuran (THF) and compared to model PS-DVB beads commonly used for solid phase synthesis.     

Water sorption in cross-linked poly(vinyl alcohol) networks

Poly(vinyl alcohol) (PVA) networks of different cross-linking densities were prepared by reaction with hexamethylene diisocyanate in solution and casting. The dynamic-mechanical properties of PVA films have been investigated in the temperature range of −150 to +150 °C. Two relaxations processes labeled α and β in order of decreasing temperature were observed. The α-relaxation shifts to lower temperature and the average molecular weight between cross-links decreases with increasing cross-linking density. Isothermal sorption from vapor and liquid water allowed determination of the Flory-Huggins interaction parameter between water and the polymer chain segments, which decreased with the water activity in the hydrogel and increased with the cross-linking density as a consequence of the hydrophobic character of the cross-linking agent. The water diffusion coefficients, D, in the networks obtained by means of dynamic sorption experiments increased with increasing water activity. This behavior is interpreted in terms of plasticization of the polymer by water molecules.     

Synthesis and characterization of CdS quantum dots with carboxylic-functionalized poly (vinyl alcohol) for bioconjugation

In the present research it is reported the synthesis and characterization of CdS nanoparticles (NPs) prepared using carboxylic-functionalized poly (vinyl alcohol) (PVA) as the ligand via aqueous route at room temperature and ambient pressure. Different molar concentrations of carboxylic-PVA and PVA were investigated aiming at producing stable colloidal systems. Carboxylic-PVA was conjugated with BSA (bovine serum albumin) and used as capping ligand in the preparation of CdS nanocrystals. UV-visible spectroscopy, photoluminescence spectroscopy, and transmission electron microscopy were used to characterize the kinetics and the relative stability of polymer-capped CdS nanocrystals. The results have clearly indicated that the carboxylic-functionalized PVA was much more effective on nucleating and stabilizing colloidal CdS nanoparticles in aqueous suspensions compared to PVA. In addition, the CdS nanocrystals were obtained in the so-called “quantum-size confinement regime”, with the calculated average size below 4.0 nm and fluorescent activity. Thus, a novel simple route was successfully developed for synthesizing nanohybrids based on quantum dots and water-soluble chemically functionalized polymers with incorporated carboxylic moiety with the possibility of direct bioconjugation.     

Synthesis of poly(vinyl alcohol) combs via MADIX/RAFT polymerization

Poly(vinyl acetate) combs have been prepared via macromolecular design via interchange of xanthate (MADIX)/reversible addition-fragmentation chain-transfer (RAFT) polymerization using xanthate functionalized polymer cores. The comb backbones were prepared using well-defined poly(vinyl alcohol) PVA polymers with a degree of polymerization of 20, 100 and 170, respectively. Functionalization with xanthates via R-group or a Z-group approach resulted in the formation of macromolecular MADIX agents. While Z group designed macromolecular xanthate agents appeared to inhibit the polymerization of vinyl acetate (VAc), R group designed macromolecular xanthate agents achieved to mediate efficiently the bulk polymerization of VAc affording PVAc combs. However, the growth of the combs was accompanied at low conversions by the formation of linear polymer chains as a result of the constant initiation (AIBN) and shoulders, which can be attributed to intermolecular coupling reactions. The proportions of single chains and termination products were observed to increase with the degree of polymerization of the macromolecular MADIX agents broadening the molecular weight distribution. As a result of a stable ester link between the branches and the PVA backbone, the branched PVAc architectures were finally hydrolyzed to afford poly(vinyl alcohol) combs.     

Preparation and characterization of high loading porous crosslinked poly(vinyl alcohol) resins

Porous crosslinked poly(vinyl alcohol) resin beads have been prepared by a two-step pathway involving a pre-crosslinking reaction followed by a reverse suspension crosslinking reaction with epichlorohydrin as crosslinker. The reaction conditions have been optimized for the two steps in order to obtain resins with various pores sizes. The crosslinking density of these resins was calculated from their swelling properties by a modified Flory equation. High loading of hydroxyl groups is one of the important characteristics of these resins (attaining ca. 17 mmol/g). The porosity, pore volume, pore structure and the swelling behavior in water of these resins have been studied.     

Preparation and characterization of α-chitin whisker-reinforced poly(vinyl alcohol) nanocomposite films with or without heat treatment

α-Chitin whisker-reinforced poly(vinyl alcohol) (PVA) nanocomposite films were prepared by solution-casting technique. The α-chitin whiskers were prepared by acid hydrolysis of α-chitin from shrimp shells. The as-prepared whiskers exhibited the length in the range of 150-800 nm and the width in the range of 5-70 nm, with the average length and width being about 417 and 33 nm, respectively. Thermal stability of the as-cast nanocomposite films was improved from those of the pure PVA film with increasing whisker content. The presence of the whiskers did not have any effect on the crystallinity of the PVA matrix. The tensile strength of α-chitin whisker-reinforced PVA films increased, at the expense of the percentage of elongation at break, from that of the pure PVA film with initial increase in the whisker content and leveled off when the whisker content was greater than or equal to 2.96 wt%. Both the addition of α-chitin whiskers and heat treatment helped improve water resistance, leading to decreased percentage degree of swelling, of the nanocomposite films.     

Facile fabrication of poly(vinyl alcohol) gels and derivative aerogels

A facile preparation of poly(vinyl alcohol) (PVOH) hydrogels and their derivative PVOH/montmorillonite clay aerogels is reported, using water as solvent and divinylsulfone as crosslinking agent, making use of an environmentally friendly freeze drying process. The materials exhibit significantly increased mechanical properties after crosslinking. The compressive modulus of an aerogel prepared from an aqueous suspension containing 2 wt% PVOH/8 wt% clay increased 29-fold upon crosslinking, for example. Crosslinking of the polymer/clay aerogels decreased the onset decomposition temperature as measured by thermogravimetric analysis, and generated a more continuous structure at higher clay contents. Such polymer/clay aerogels are promising materials for low flammability applications.     

Viscoelastic properties of poly(vinyl alcohol) hydrogels and ferrogels obtained through freezing-thawing cycles

We report the preparation of poly(vinyl alcohol) (PVA) hydrogels obtained through freezing-thawing cycles. The viscoelastic properties of these gels using parallel-plate shear mode were evaluated as a function of temperature, time, degree of swelling, concentration and the number of freezing-thawing cycles. The storage modulus was analyzed on the basis of a theoretical model based on the scaling approach. These results provide additional evidence for a non-crystalline nature of the structure of PVA cryogels.Furthermore, PVA ferrogels have been prepared from PVA aqueous solutions and a ferrofluid through freezing-thawing cycles. The viscoelastic properties of these materials have been evaluated. It is shown that the variation of the storage modulus with ferrofluid concentration cannot be fitted using classical theories what has been attributed to the small dimensions of the particles in the ferrogels and to the magnetic interactions between particles.     

粉煤灰固定化细胞去除聚乙烯醇的研究

前期研究分离到一株能高效降解并矿化聚乙烯醇(PVA)的黄单胞菌(Xanthomonas sp.)。考察了利用改性处理或未处理粉煤灰吸附该菌株去除PVA的特性。结果表明,实验所采用的5种粉煤灰对该菌细胞等温吸附方程与Langmuir方程、Freundlich方程的拟合都达到很高的水平。改性粉煤灰对菌体细胞的吸附量由大到小的顺序为HC l处理粉煤灰>H2SO4处理粉煤灰>Ca(OH)2处理粉煤灰>NaOH处理粉煤灰>未处理粉煤灰。在培养初期,粉煤灰固定化细胞对PVA的去除量略低于等量游离细胞,但其去除速率的变化与游离细胞基本相同。     

Electron beam synthesis and characterization of poly(vinyl alcohol)/montmorillonite nanocomposites

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanocomposites in the form of films were prepared under the effect of electron beam irradiation. The PVA/MMT nanocomposites gels were characterized by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and mechanical measurements. The study showed that the appropriate dose of electron beam irradiation to achieve homogeneous nanocomposites films and highest gel formation was 20 kGy. The introduction of MMT (up to 4 wt %) results in improvement in tensile strength, elongation at break, and thermal stability of the PVA matrix. In addition, the intercalation of PVA with the MMT clay leads to an impressive improved water resistance, indicating that the clay is well dispersed within the polymer matrix. Meanwhile, it was proved that the intercalation has no effect on the metal uptake capability of PVA as determined by a method based on the color measurements. XRD patterns and SEM micrographs suggest the coexistence of exfoliated intercalated MMT layers over the studied MMT contents. The DSC thermograms showed clearly that the intercalation of PVA polymer with these levels of MMT has no influence on the melting transitions; however, the glass transition temperature (T_g) for PVA was completely disappeared, even at low levels of MMT clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1129–1138, 2006     

Morphology-rheology relationship in hyaluronate/poly(vinyl alcohol)/borax polymer blends

In this work, we have prepared bioartificial polymer blends using hyaluronate (HA) as a biological component and poly(vinyl alcohol)-borax association (PVAs) as a synthetic component, and investigated the rheological properties as well as morphology of the blends. When plotted against the blend composition, the rheological properties showed both positive and negative deviation from the linear additive mixing rule depending on thermal history. The blend showed enhanced viscosity at the composition of 20 wt% of HA and 80 wt% of PVAs, when PVA was dissolved at high temperature. The viscosity enhancement was caused by the network formation of HA aggregates in the micrometer scale. In addition, the network structure of HA aggregates was found to be fractal with the fractal dimension of 1.7. As PVA system also forms a network structure in the nanometer scale between hydroxyl groups of PVA and borate anions, the blend system is unique in that it has network structures in both micrometer and nanometer scales in one material. On the contrary, HA formed aggregates but not any network structure in the blend of the same composition but of the negative deviation. In conclusion, we showed that HA/PVAs blend system may have diverse morphology as well as very broad spectrum of rheological properties, and could suggest that the rheology and morphology of HA/PVAs blends can be designed not only by controlling composition but also by controlling thermal and deformation history of the components.     

Transition of hydration states of poly(vinyl alcohol) in aqueous solution

A straightforward method for determination of the hydration number of polymer in aqueous solution based on ice-melting technique of DSC is proposed. The simple yet precise method has been applied to determine the hydration number of poly(vinyl alcohol) (PVA) in aqueous solution covering a wide range of concentrations, from 0.005 to 0.3 g(solute)/g(solution), for three samples with different molar masses. The hydration number of PVA maintains a constant lower value of 2.5 when the concentration exceeds 0.2 g(solute)/g(solution). It increases to a value of 7 when the concentration decreases to the overlap concentration C^∗ of the polymer, where C^∗ was estimated as the reciprocal of its intrinsic viscosity. For solutions of C < C^∗, the hydration number keeps constant again at the value of 7. This behavior evidently demonstrates that PVA has two hydration states, one occurs at the dilute regime and the other occurs at concentrated regime. The concentration dependent transition from one state to another is treated mathematically by a quantitative formula which involves two parameters: one denotes the transition concentration and the other denotes the width of the transition region. The transition concentration decreases linearly with increasing molar mass resembling the behavior of molar mass dependence of overlap concentration. The structural features for the two states of hydrated PVA are briefly discussed.     

Fabrication of poly(vinyl alcohol)s (PVAs) nanotubes through the fusion of nanocapsules composed of PVAs multilayer films

Poly(vinyl alcohol) (PVA) nanocapsules were fabricated by the deposition of PVA multilayer films onto the surface of silica particles followed by the removal of the silica cores. When a water dispersion of PVA nanocapsules was dried on a substrate, PVA nanotubes were formed through the one-dimensional fusion of the nanocapsules. This fusion behavior of the PVA nanocapsules was strongly affected by the molecular weights and acetylation degrees of PVA, the capsule film thickness of the PVA nanocapsules and the temperature to dry a water dispersion of the nanocapsules. When nanocapsules composed of 20 layered films of acetylated PVA with a 14% acetylation degree were used, nanotube formation via the fusion of these nanocapsules occurred effectively upon drying the water dispersion at 20 °C.     

Effect of crosslinking on the mechanical and thermal properties of poly(vinyl alcohol)

Poly(vinyl alcohol) was crosslinked with hexamethylene diisocyanate in solution. A broad range of degrees of crosslinking, from 1.7 up to 74 mol% of reacted hydroxyl groups, was achieved. The variation of the thermal and mechanical properties of PVA with the crosslinking density show an initial decrease due to the diminution of the crystallinity of the system, caused by the crosslinking. After an abrupt rise at about 20%, the properties tend to level off independently on the increase of the crosslinking. This behaviour is explained as a result of the competitive action of at least three factors during the crosslinking: (i) weakening of the existing physical network due to hydrogen bonding; (ii) formation of a chemical network; and (iii) introduction of flexible moieties. The last factor is closely connected with the specific chemical structure of the crosslinker itself.     

Swelling and morphological properties of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) hydrogels in solution with high salt concentration

Understanding the swelling properties of hydrogels and how they affect the hydrogel's morphology is of fundamental importance in the development of hydrogel-based artificial muscles, bio-actuators, sensors and other devices. In this paper, the swelling behavior of PVA-PAA hydrogel films in saline water and in buffer solutions of different pH values was investigated. It was observed that the swelling factor of the hydrogel decreases when the ionic strength of the solvent solution increases. Scanning Electron Microscopy (SEM) revealed structures with different pore shapes and sizes depending on the type of solution used for hydration. In saline water, Energy Dispersive X-Ray (EDS) analysis indicated the formation of NaCl crystals within the polymeric network. Finally, the PVA-PAA hydrogel was used as an actuator to strain a fiber Bragg grating sensor, thus providing an indirect measurement of the pH value of the surrounding solution.