Low-voltage high-gain differential OTA for SC circuits

A new differential operational transconductance amplifier (OTA) for SC circuits that operates with a supply voltage of less than two transistor threshold voltages is presented. Its simplicity relies on the use of a low-voltage regulated cascode circuit, which achieves very high output impedance under low-voltage restrictions. The OTA has been designed to operate with a supply voltage of V/sub DD/=1.5 V, using a 0.6 /spl mu/m CMOS technology with transistor threshold voltages of V/sub TN/=0.75 V and V/sub TP/=-0.85 V. Post-layout simulation results for a load capacitance (C/sub L/) of 2 pF show a 75 MHz gain-bandwidth product and 100 dB DC gain with a quiescent power consumption of 750 /spl mu/W.     

SODEL FET: novel channel and source/drain profile engineering schemes by selective Si epitaxial growth technology

In this paper, novel channel and source/drain profile engineering schemes are proposed for sub-50-nm bulk CMOS applications. This device, referred to as the silicon-on-depletion layer FET (SODEL FET), has the depletion layer beneath the channel region, which works as an insulator like a buried oxide in a silicon-on-insulator MOSFET. Thanks to this channel structure, junction capacitance (C/sub j/) has been reduced in SODEL FET, i.e., C/sub j/ (area) was /spl sim/0.73 fF//spl mu/m/sup 2/ both in SODEL nFET and pFET at Vbias =0.0 V. The body effect coefficient /spl gamma/ is also reduced to less than 0.02 V/sup 1/2/. Nevertheless, current drives of 886 /spl mu/A//spl mu/m (I/sub off/=15 nA//spl mu/m) in nFET and -320 /spl mu/A//spl mu/m (I/sub off/=10 nA//spl mu/m) in pFET have been achieved in 70-nm gate length SODEL CMOS with |V/sub dd/|=1.2 V. New circuit design schemes are also proposed for high-performance and low-power CMOS applications using the combination of SODEL FETs and bulk FETs on the same chip for 90-nm-node generation and beyond.     

DC and RF characteristics of E-mode Ga/sub 0.51/In/sub 0.49/P-In/sub 0.15/Ga/sub 0.85/As pseudomorphic HEMTs

The DC and RF characteristics of Ga/sub 0.49/In/sub 0.51/P-In/sub 0.15/Ga/sub 0.85/As enhancement- mode pseudomorphic HEMTs (pHEMTs) are reported for the first time. The transistor has a gate length of 0.8 /spl mu/m and a gate width of 200 /spl mu/m. It is found that the device can be operated with gate voltage up to 1.6 V, which corresponds to a high drain-source current (I/sub DS/) of 340 mA/mm when the drain-source voltage (V/sub DS/) is 4.0 V. The measured maximum transconductance, current gain cut-off frequency, and maximum oscillation frequency are 255.2 mS/mm, 20.6 GHz, and 40 GHz, respectively. When this device is operated at 1.9 GHz under class-AB bias condition, a 14.7-dBm (148.6 mW/mm) saturated power with a power-added efficiency of 50% is achieved when the drain voltage is 3.5 V. The measured F/sub min/ is 0.74 dB under I/sub DS/=15 mA and V/sub DS/=2 V.     

High breakdown voltage (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P/InGaAs quasi-enhancement-mode pHEMT with field-plate technology

A high breakdown voltage and a high turn-on voltage (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P/InGaAs quasi-enhancement-mode (E-mode) pseudomorphic HEMT (pHEMTs) with field-plate (FP) process is reported for the first time. Between gate and drain terminal, the transistor has a FP metal of 1 /spl mu/m, which is connected to a source terminal. The fabricated 0.5/spl times/150 /spl mu/m/sup 2/ device can be operated with gate voltage up to 1.6 V owing to its high Schottky turn-on voltage (V/sub ON/=0.85 V), which corresponds to a high drain-to-source current (I/sub ds/) of 420 mA/mm when drain-to-source voltage (V/sub ds/) is 3.5 V. By adopting the FP technology and large barrier height (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P layer design, the device achieved a high breakdown voltage of -47 V. The measured maximum transconductance, current gain cutoff frequency and maximum oscillation frequency are 370 mS/mm, 22 GHz , and 85 GHz, respectively. Under 5.2-GHz operation, a 15.2 dBm (220 mW/mm) and a 17.8 dBm (405 mW/mm) saturated output power can be achieved when drain voltage are 3.5 and 20 V. These characteristics demonstrate that the field-plated (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P E-mode pHEMTs have great potential for microwave power device applications.     

Low-power low-voltage differential class-AB OTAs for SC circuits

Two new differential class-AB operational transconductance amplifiers (OTAs) for SC circuits that operate with a supply voltage of less than two transistor threshold voltages are introduced. They make use of a new class-AB pseudodifferential pair to generate signal currents much larger than quiescent currents. Both OTAs have been designed to operate with a supply voltage of V/sub DD/=1.1 V, using a 0.35 /spl mu/m CMOS technology. Simulation results for a load capacitance (C/sub L/) of 1 pF show 15 MHz gain-bandwidth product with a quiescent power consumption of 10 /spl mu/W.     

Microwave noise performance of AlGaN-GaN HEMTs with small DC power dissipation

We report low microwave noise performance of discrete AlGaN-GaN HEMTs at DC power dissipation comparable to that of GaAs-based low-noise FETs. At 1-V source-drain (SD) bias and DC power dissipation of 97 mW/mm, minimum noise figures (NF/sub min/) of 0.75 dB at 10 GHz and 1.5 dB at 20 GHz were achieved, respectively. A device breakdown voltage of 40 V was observed. Both the low microwave noise performance at small DC power level and high breakdown voltage was obtained with a shorter SD spacing of 1.5 /spl mu/m in 0.15-/spl mu/m gate length GaN HEMTs. By comparison, NF/sub min/ with 2 /spl mu/m SD spacing was 0.2 dB greater at 10 GHz.     

10-W/mm AlGaN-GaN HFET with a field modulating plate

AlGaN-GaN heterojunction field-effect transistors (HFETs) with a field modulating plate (FP) were fabricated on an SiC substrate. The gate-drain breakdown voltage (BV/sub gd/) was significantly improved by employing an FP electrode, and the highest BV/sub gd/ of 160 V was obtained with an FP length (L/sub FP/) of 1 /spl mu/m. The maximum drain current achieved was 750 mA/mm, together with negligibly small current collapse. A 1-mm-wide FP-FET (L/sub FP/=1 /spl mu/m) biased at a drain voltage of 65 V demonstrated a continuous wave saturated output power of 10.3 W with a linear gain of 18.0 dB and a power-added efficiency of 47.3% at 2 GHz. To our knowledge, the power density of 10.3 W/mm is the highest ever achieved for any FET of the same gate size.     

High-performance enhancement-mode AlGaN/GaN HEMTs using fluoride-based plasma treatment

We report a novel approach in fabricating high-performance enhancement mode (E-mode) AlGaN/GaN HEMTs. The fabrication technique is based on fluoride-based plasma treatment of the gate region in AlGaN/GaN HEMTs and post-gate rapid thermal annealing with an annealing temperature lower than 500/spl deg/C. Starting with a conventional depletion-mode HEMT sample, we found that fluoride-based plasma treatment can effectively shift the threshold voltage from -4.0 to 0.9 V. Most importantly, a zero transconductance (g/sub m/) was obtained at V/sub gs/=0 V, demonstrating for the first time true E-mode operation in an AlGaN/GaN HEMT. At V/sub gs/=0 V, the off-state drain leakage current is 28 /spl mu/A/mm at a drain-source bias of 6 V. The fabricated E-mode AlGaN/GaN HEMTs with 1 /spl mu/m-long gate exhibit a maximum drain current density of 310 mA/mm, a peak g/sub m/ of 148 mS/mm, a current gain cutoff frequency f/sub T/ of 10.1 GHz and a maximum oscillation frequency f/sub max/ of 34.3 GHz.     

Influences of sulfur passivation on temperature-dependent characteristics of an AlGaAs/InGaAs/GaAs PHEMT

The influences of (NH/sub 4/)/sub 2/S/sub x/ treatment on an AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor (PHEMT) are studied and demonstrated. Upon the sulfur passivation, the studied device exhibits better temperature-dependent dc and microwave characteristics. Experimentally, for a 1/spl times/100 /spl mu/m/sup 2/ gate/dimension PHEMT with sulfur passivation, the higher gate/drain breakdown voltage of 36.4 (21.5) V, higher turn-on voltage of 0.994 (0.69) V, lower gate leakage current of 0.6 (571) /spl mu/A/mm at V/sub GD/=-22 V, improved threshold voltage of -1.62 (-1.71) V, higher maximum transconductance of 240 (211) mS/mm with 348 (242) mA/mm broad operating regime (>0.9g/sub m,max/), and lower output conductance of 0.51 (0.53) mS/mm are obtained, respectively, at 300 (510) K. The corresponding unity current gain cutoff frequency f/sub T/ (maximum oscillation frequency f/sub max/) are 22.2 (87.9) and 19.5 (59.3) GHz at 250 and 400 K, respectively, with considerably broad operating regimes (>0.8f/sub T/,f/sub max/) larger than 455 mA/mm. Moreover, the relatively lower variations of device performances over wide temperature range (300/spl sim/510 K) are observed.     

High-temperature thermal stability performance in /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As metamorphic HEMT

We report, to our knowledge, the best high-temperature characteristics and thermal stability of a novel /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As--GaAs metamorphic high-electron mobility transistor. High-temperature device characteristics, including extrinsic transconductance (g/sub m/), drain saturation current density (I/sub DSS/), on/off-state breakdown voltages (BV/sub on//BV/sub GD/), turn-on voltage (V/sub on/), and the gate-voltage swing have been extensively investigated for the gate dimensions of 0.65/spl times/200 /spl mu/m/sup 2/. The cutoff frequency (f/sub T/) and maximum oscillation frequency (f/sub max/), at 300 K, are 55.4 and 77.5 GHz at V/sub DS/=2 V, respectively. Moreover, the distinguished positive thermal threshold coefficient (/spl part/V/sub th///spl part/T) is superiorly as low as to 0.45 mV/K.     

A high current gain 4H-SiC NPN power bipolar junction transistor

This work reports the development of high power 4H-SiC bipolar junction transistors (BJTs) by using reduced implantation dose for p+ base contact region and annealing in nitric oxide of base-to-emitter junction passivation oxide for 2 hours at 1150/spl deg/C. The transistor blocks larger than 480 V and conducts 2.1 A (J/sub c/=239 A/cm/sup 2/) at V/sub ce/=3.4 V, corresponding to a specific on-resistance (R/sub sp on/) of 14 m/spl Omega/cm/sup 2/, based on a drift layer design of 12 /spl mu/m doped to 6/spl times/10/sup 15/cm/sup -3/. Current gain /spl beta//spl ges/35 has been achieved for collector current densities ranging from J/sub c/=40 A/cm/sup 2/ to 239 A/cm/sup 2/ (I/sub c/=2.1 A) with a peak current gain of 38 at J/sub c/=114 A/cm/sup 2/.     

Two-phase boosted voltage generator for low-voltage DRAMs

A two-phase boosted voltage (V/sub PP/) generator circuit was proposed for use in gigabit DRAMs. It reduced the maximum gate-oxide voltage of pass transistor and the lower limit of supply voltage to V/sub PP/ and V/sub TN/, respectively, while those for the conventional charge-pump circuit are V/sub PP/+V/sub DD/ and 1.5 V/sub TN/ respectively. Also, the pumping current was increased in the new circuit. The newly proposed two-phase V/sub PP/ charge-pump circuit worked successfully at V/sub DD/ down to 0.8 V by eliminating the threshold voltage loss of the control pulse generator and was tested successfully in a 0.16-/spl mu/m test chip using triple-well CMOS technology.     

A fully integrated SOI RF MEMS technology for system-on-a-chip applications

In this paper, a silicon-on-insulator (SOI) radio-frequency (RF) microelectromechanical systems (MEMS) technology compatible with CMOS and high-voltage devices for system-on-a-chip applications is experimentally demonstrated for the first time. This technology allows the integration of RF MEMS switches with driver and processing circuits for single-chip communication applications. The SOI high-voltage device (0.7-/spl mu/m channel length, 2-/spl mu/m drift length, and over 35-V breakdown voltage), CMOS devices (0.7-/spl mu/m channel length and 1.3/-1.2 V threshold voltage), and RF MEMS capacitive switch (insertion loss 0.14 dB at 5 GHz and isolation 9.5 dB at 5 GHz) are designed and fabricated to show the feasibility of building fully integrated RF systems. The performance of the fabricated RF MEMS capacitive switches on low-resistivity and high-resistivity SOI substrates will also be compared.     

Graded base type-II InP/GaAsSb DHBT with f/sub T/=475 GHz

The first demonstration of a type-II InP/GaAsSb double heterojunction bipolar transistor (DHBT) with a compositionally graded InGaAsSb to GaAsSb base layer is presented. A device with a 0.4/spl times/6 /spl mu/m/sup 2/ emitter dimensions achieves peak f/sub T/ of 475 GHz (f/sub MAX/=265 GHz) with current density at peak f/sub T/ exceeding 12 mA//spl mu/m/sup 2/. The structure consists of a 25-nm InGaAsSb/GaAsSb graded base layer and 65-nm InP collector grown by MBE with breakdown voltage /spl sim/4 V which demonstrates the vertical scaling versus breakdown advantage over type-I DHBTs.     

4H-SiC power bipolar junction transistor with a very low specific ON-resistance of 2.9 m/spl Omega//spl middot/cm/sup 2/

This letter reports a newly achieved best result on the specific ON-resistance (R/sub SP/spl I.bar/ON/) of power 4H-SiC bipolar junction transistors (BJTs). A 4H-SiC BJT based on a 12-/spl mu/m drift layer shows a record-low specific-ON resistance of only 2.9 m/spl Omega//spl middot/cm/sup 2/, with an open-base collector-to-emitter blocking voltage (V/sub ceo/) of 757 V, and a current gain of 18.8. The active area of this 4H-SiC BJT is 0.61 mm/sup 2/, and it has a fully interdigitated design. This high-performance 4H-SiC BJT conducts up to 5.24 A at a forward voltage drop of V/sub CE/=2.5 V, corresponding to a low R/sub SP-ON/ of 2.9 m/spl Omega//spl middot/cm/sup 2/ up to J/sub c/=859 A/cm/sup 2/. This is the lowest specific ON-resistance ever reported for high-power 4H-SiC BJTs.     

A 160-GHz f/sub T/ and 140-GHz f/sub MAX/ submicrometer InP DHBT in MBE regrown-emitter technology

We report a 0.7/spl times/8 /spl mu/m/sup 2/ InAlAs-InGaAs-InP double heterojunction bipolar transistor, fabricated in a molecular-beam epitaxy (MBE) regrown-emitter technology, exhibiting 160 GHz f/sub T/ and 140 GHz f/sub MAX/. These initial results are the first known RF results for a nonselective regrown-emitter heterojunction bipolar transistor, and the fastest ever reported using a regrown base-emitter heterojunction. The maximum current density is J/sub E/=8/spl times/10/sup 5/ A/cm/sup 2/ and the collector breakdown voltage V/sub CEO/ is 6 V for a 1500-/spl Aring/ collector. In this technology, the dimension of base-emitter junction has been scaled to an area as low as 0.3/spl times/4 /spl mu/m/sup 2/ while a larger-area extrinsic emitter maintains lower emitter access resistance. Furthermore, the application of a refractory metal (Ti-W) base contact beneath the extrinsic emitter regrowth achieves a fully self-aligned device topology.     

High performance 35 nm gate length CMOS with NO oxynitride gate dielectric and Ni salicide

The 35 nm gate length CMOS devices with oxynitride gate dielectric and Ni salicide have been fabricated to study the feasibility of higher performance operation. Nitrogen concentration in gate oxynitride was optimized to reduce gate current I/sub g/ and to prevent boron penetration in the pFET. The thermal budget in the middle of the line (MOL) process was reduced enough to realize shallower junction depth in the S/D extension regions and to suppress gate poly-Si depletion. Finally, the current drives of 676 /spl mu/A//spl mu/m in nFET and 272 /spl mu/A//spl mu/m in pFET at V/sub dd/=0.85 V (at I/sub off/=100 nA//spl mu/m) were achieved and they are the best values for 35 nm gate length CMOS reported to date.     

2 V-operated InGaP-AlGaAs-InGaAs enhancement-mode pseudomorphic HEMT

A low-voltage single power supply enhancement-mode InGaP-AlGaAs-InGaAs pseudomorphic high-electron mobility transistor (PHEMT) is reported for the first time. The fabricated 0.5/spl times/160 /spl mu/m/sup 2/ device shows low knee voltage of 0.3 V, drain-source current (I/sub DS/) of 375 mA/mm and maximum transconductance of 550 mS/mm when drain-source voltage (V/sub DS/) was 2.5 V. High-frequency performance was also achieved; the cut-off frequency(F/sub t/) is 60 GHz and maximum oscillation frequency(F/sub max/) is 128 GHz. The noise figure of the 160-/spl mu/m gate width device at 17 GHz was measured to be 1.02 dB with 10.12 dB associated gain. The E-mode InGaP-AlGaAs-InGaAs PHEMT exhibits a high output power density of 453 mW/mm with a high linear gain of 30.5 dB at 2.4 GHz. The E-mode PHEMT can also achieve a high maximum power added efficiency (PAE) of 70%, when tuned for maximum PAE.     

A 2-V 23-/spl mu/A 5.3-ppm//spl deg/C curvature-compensated CMOS bandgap voltage reference

A high-order curvature-compensated CMOS bandgap reference, which utilizes a temperature-dependent resistor ratio generated by a high-resistive poly resistor and a diffusion resistor, is presented in this paper. Implemented in a standard 0.6-/spl mu/m CMOS technology with V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C, the proposed voltage reference can operate down to a 2-V supply and consumes a maximum supply current of 23 /spl mu/A. A temperature coefficient of 5.3 ppm//spl deg/C at a 2-V supply and a line regulation of /spl plusmn/1.43 mV/V at 27/spl deg/C are achieved. Experimental results show that the temperature drift is reduced by approximately five times when compared with a conventional bandgap reference in the same technology.     

SOI technology for radio-frequency integrated-circuit applications

This paper presents a silicon-on-insulator (SOI) integration technology, including structures and processes of OFF-gate power nMOSFETs, conventional lightly doped drain (LDD) nMOSFETs, and spiral inductors for radio frequency integrated circuit (RFIC) applications. In order to improve the performance of these integrated devices, body contact under the source (to suppress floating-body effects) and salicide (to reduce series resistance) techniques were developed for transistors; additionally, locally thickened oxide (to suppress substrate coupling) and ultra-thick aluminum up to 6 /spl mu/m (to reduce spiral resistance) were also implemented for spiral inductors on high-resistivity SOI substrate. All these approaches are fully compatible with the conventional CMOS processes, demonstrating devices with excellent performance in this paper: 0.25-/spl mu/m gate-length offset-gate power nMOSFET with breakdown voltage (BV/sub DS/) /spl sim/ 22.0 V, cutoff frequency (f/sub T/)/spl sim/15.2 GHz, and maximal oscillation frequency (f/sub max/)/spl sim/8.7 GHz; 0.25-/spl mu/m gate-length LDD nMOSFET with saturation current (I/sub DS/)/spl sim/390 /spl mu/A//spl mu/m, saturation transconductance (g/sub m/)/spl sim/197 /spl mu/S//spl mu/m, cutoff frequency /spl sim/ 25.6 GHz, and maximal oscillation frequency /spl sim/ 31.4 GHz; 2/5/9/10-nH inductors with maximal quality factors (Q/sub max/) 16.3/13.1/8.95/8.59 and self-resonance frequencies (f/sub sr/) 17.2/17.7/6.5/5.8 GHz, respectively. These devices are potentially feasible for RFIC applications.