Quantitative relationship between the maximum streamer length and discharge voltage of a pulsed positive streamer discharge in water

A linear relationship has been realized between the maximum streamer length and discharge voltage of a pulsed positive streamer discharge by measuring the streamer length in water with conductivity of 100 μS cm-1using high-speed photography. Based on Ohm's law, a quantitative equation has been derived for the dependence of the maximum streamer length on the discharge voltage of a pulsed positive streamer discharge in water. According to the equation, our results suggest that the streamers spontaneously stop propagating through water due to the voltage at the streamer head dropping below the ignition voltage of a pulsed positive streamer discharge.     

The Degradation of Organic Pollutants by Bubble Discharge in Water

Organic pollutants could be degraded by using bubble discharge in water with gas aeration in the discharge reactor and more plasma can be generated in the discharge process.When pulsed high voltage was applied between electrodes with gas aerated into the reactor,it showed that bubbles were broken,which meant that breakdown took place.It could also be observed that the removal rate of phenol increased with increasing discharge voltage or pulse frequency,and with reducing initial phenol concentration or solution electric conductivity.It could remove more amount of phenol by oxygen aeration.With increasing oxygen flow rate,the removal rate increased.There was little difference with air or nitrogen aeration for phenol removal.The solution temperature after discharge increased to a great extent.However,this part of energy consumption did not contribute to the reaction,which led to a reduction in the energy utilization efficiency.     

Degradation of phenol using a combination of granular activated carbon adsorption and bipolar pulse dielectric barrier discharge plasma regeneration

A combined method of granular activated carbon (GAC) adsorption and bipolar pulse dielectric barrier discharge (DBD) plasma regeneration was employed to degrade phenol in water. After being saturated with phenol, the GAC was filled into the DBD reactor driven by bipolar pulse power for regeneration under various operating parameters. The results showed that different peak voltages, air flow rates, and GAC content can affect phenol decomposition and its major degradation intermediates, such as catechol, hydroquinone, and benzoquinone. The higher voltage and air support were conducive to the removal of phenol, and the proper water moisture of the GAC was 20％. The amount of H2O2 on the GAC was quantitatively determined, and its laws of production were similar to phenol elimination. Under the optimized conditions, the elimination of phenol on the GAC was confirmed by Fourier transform infrared spectroscopy,and the total removal of organic carbons achieved 50.4％. Also, a possible degradation mechanism was proposed based on the HPLC analysis. Meanwhile, the regeneration efficiency of the GAC was improved with the discharge treatment time, which attained 88.5％ after 100 min of DBD processing.     

Synergistic Decolouration of Azo Dye by Pulsed Streamer Discharge Immobilized TiO2 Photocatalysis

Photocatalyst was prepared by immobilizing TiO2 on glass beads using the traditional sol-gel method. Ultraviolet light （UV） produced by pulsed streamer discharge was then used to induce photocatalytic activity of TiO2 photocatalyst. Decolouration efficiency of the representative azo dye （acid orange 7, AOT） was investigated using the synergistic system of pulsed streamer discharge plasma and TiO2 photocatalysis. The obtained results showed that the decolouration rate of AO7 could be increased by 16.7% under the condition of adding supported TiO2 in the pulsed streamer discharge system, compared to that in the sole pulsed streamer discharge plasma system, due to the synergistic effect of pulsed streamer discharge and TiO2 photocatalysis induced by pulsed streamer discharge. The synergistic system of pulsed streamer discharge and TiO2 photocatalyst was found to have more reactive radicals for degradation of organic compounds in water.     

The effect of the configuration of a single electrode corona discharge on its acoustic characteristics

A new sparker system based on pulsed spark discharge with a single electrode has already been utilized for oceanic seismic exploration. However, the electro-acoustic energy efficiency of this system is lower than that of arc discharge based systems. A simple electrode structure was investigated in order to improve the electro-acoustic energy efficiency of the spark discharge.Experiments were carried out on an experimental setup with discharge in water driven by a pulsed power source. The voltage–current waveform, acoustic signal and bubble oscillation were recorded when the relative position of the electrode varied. The electro-acoustic energy efficiency was also calculated. The load voltage had a saltation for the invaginated electrode tip,namely an obvious voltage remnant. The more the electrode tip was invaginated, the larger the pressure peaks and first period became. The results show that electrode recessing into the insulating layer is a simple and effective way to improve the electro-acoustic energy efficiency from 2% to about 4%.     

Characteristics of Electrode-Water-Electrode Discharge and its Application to Water Treatment

Atmospheric air discharge above the surface of water is an effective method for water treatment.The leakage current and Joule heating of water are reduced by the air gap,which raises the energy efficiency of the water treatment.However,the application of this kind of discharge is limited by a pair of conflicting factors：the chemical efficiency grows as the discharge gap distance decreases,while the spark breakdown voltage decreases as the gap distance decreases.To raise the spark breakdown voltage and the chemical efficiency of atmospheric pressure water surface discharge,both the high-voltage electrode and the ground electrode are suspended above the water surface to form an electrode-water-electrode discharge system.For this system,there are two potential discharge directions：from one electrode to another directly,and from the electrodes to the water surface.The first step in utilizing the electrode-water-electrode discharge is to find out the discharge direction transition criterion.In this paper,the discharge direction transition criterions of spark discharge and streamer discharge are presented.By comparing the discharge characteristics and the chemical efficiencies,the discharge propagating from the electrodes to the water surface is proved to be more suitable for water treatment than that propagating directly between the electrodes.     

Measurement of Temporally and Spatially Resolved Electron Density in the Filament of a Pulsed Spark Discharge in Water

The temporally and spatially resolved optical emission spectrum of Hα of a pulsed spark discharge in water was experimentally measured. The temporally and spatially resolved electron densities, along the radial direction of the spark filament, for a pulsed spark discharge in water with a conductivity of 100 μS/cm were investigated. The electron density in the spark filament was found to be in the 10~(18)/cm~3 order of magnitude. The highest electron density was measured at the primary stage of the spark filament, and it decreased with time. The radial distribution of electron density increased from the center to the edge of the spark filament.     

A Repetitive Nanosecond Pulse Source for Generation of Large Volume Streamer Discharge

Using a unipolar pulse with the rise time and the pulse duration in the order of microsecond as the primary pulse, a nanosecond pulse with the repetitive frequency of several kilohertz is generated by a spark gap switch. By varying both the inter-pulse duration and the pulse frequency, the voltage recovery rate of the spark gap switch is investigated at different working conditions such as the gas pressure, the gas composition as well as the bias voltage. The results reveal that either increase in gas pressure or addition of SF6 to the air can increase the voltage recovery rate. The effect of gas composition on the voltage recovery rate is discussed based on the transferring and distribution of the residual space charges. The repetitive nanosecond pulse source is also applied to the generation of large volume, and the discharge currents are measured to investigate the effect of pulse repetition rate on the large volume streamer discharge.     

Time-resolved spectroscopy of femtosecond laser-induced Cu plasma with spark discharge

The combination of spark discharge and laser-induced breakdown spectroscopy (LIBS) is called spark discharge assisted LIBS. It works under laser-plasma triggered spark discharge mode, and shows its ability to enhance spectral emission intensity. This work uses a femtosecond laser as the light source, since femtosecond laser has many advantages in laser-induced plasma compared with nanosecond laser, meanwhile, the study on femtosecond LIBS with spark discharge is rare. Time-resolved spectroscopy of spark discharge assisted femtosecond LIBS was investigated under different discharge voltages and laser energies. The results showed that the spectral intensity was significantly enhanced by using spark discharge compared with LIBS alone. And, the spectral emission intensity using spark discharge assisted LIBS increased with the increase in the laser energy. In addition, at low laser energy, there was an obvious delay on the discharge time compared with high laser energy, and the discharge time with positive voltage was different from that with negative voltage.     

Plasma propagation in single-particle packed dielectric barrier discharges: joint effects of particle shape and discharge gap

In this work, a single Al₂O₃ particle packed dielectric barrier discharge (DBD) reactor with adjustable discharge gap is built, and the influences of the particle shape (ball and column) and the residual gap between the top electrode and particle on the electrical and optical characteristics of plasma are studied. Our research confirms that streamer discharge and surface discharge are the two main discharge patterns in the single-particle packed DBD reactor. The strong electric field distortion at the top of the ball or column caused by the dielectric polarization effect is an important reason for the formation of streamer discharge. The length of streamer discharge is proportional to the size of the residual gap, but the number of discharge times of a single voltage cycle shows an opposite trend. Compared to the column, a smooth spherical surface is more conducive to the formation of large and uniform surface discharges. The surface discharge area and the discharge intensity reach a maximum when the gap is equal to the diameter of the ball. All in all, the results of this study will provide important theoretical support for the establishment of the synergistic characteristics of discharge and catalysis in plasma catalysis.     

Investigation on pulsed discharge mode in SF_6-C_2H_6 mixtures

The non-chain chemical HF(DF)laser is one of the most powerful electrically-driven lasers operating in mid-infrared,in which SF6-C2H6 mixtures are often used as lasering media.Due to the electronegativity of SF6,the discharge in SF6-C2H6 presents a complicated discharge mode.To achieve reproducible pulsed laser output,pulsed discharge in SF6-C2H6 mixtures is investigated for discharge mode using plane electrodes assisted by array pre-ionization spark pins in cathode surface.Firstly,two modes can be distinguished.One mode is called the selfsustained volume discharge(SSVD),which is characterized by spatial uniformity in the discharge gap and pulse to pulse repeatability.On the contrary,another mode includes random arc passages in the discharge gap and therefore cannot conduct lasering.By varying discharge conditions(gap voltage,gas pressure,etc)two discharge modes are observed.Secondly,the holding scope of the SSVD mode is analyzed for the optimal mixture ratio of 20:1,and the boundary tend of the holding scope of SSVD indicates there exists maximum gas pressure and maximum charging voltage for SSVD.Finally,the peak current of SSVD relates positively to charging voltage,while negatively to gas pressure,from which it is drawn that synchronous electron avalanches initiated by the sliding array overlap spatially into SSVD and thus SSVD is essentially an α ionization avalanche.     

Novel electrode structure in a DBD reactor applied to the degradation of phenol in aqueous solution

Phenol degradation experimental results are presented in a similar wastewater aqueous solution using a non-thermal plasma reactor in a coaxial dielectric barrier discharge. The novelty of the work is that one of the electrodes of the reactor has the shape of a hollow screw which shows an enhanced efficiency compared with a traditional smooth structure. The experimentation was carried out with gas mixtures of 90% Ar–10% O_2, 80% Ar–20% O_2 and 0% Ar–100% O_2. After one hour of treatment the removal efficiency was 76%, 92%, and 97%, respectively, assessed with a gas chromatographic mass spectrometry technique. For both reactors used, the ozone concentration was measured. The screw electrode required less energy, for all gas mixtures, than the smooth electrode, to maintain the same ozone concentration. On the other hand, it was also observed that in both electrodes the electrical conductivity of the solution changed slightly from~0.0115 S m~(-1) up to ~0.0430 S m~(-1) after one hour of treatment. The advantages of using the hollow screw electrode structure compared with the smooth electrode were:(1) lower typical power consumption,(2) the generation of a uniform plasma throughout the reactor benefiting the phenol degradation,(3) a relatively lower temperature of the aqueous solution during the process, and(4) the plasma generation length is larger.     

Research on quinoline degradation in drinking water by a large volume strong ionization dielectric barrier discharge reaction system

Quinoline is widely used in the production of drugs as a highly effective insecticide, and its derivatives can also be used to produce dyes. It has a teratogenic carcinogen to wildlife and humans once entering into the aquatic environment. In this study, the degradation mechanism of quinoline in drinking water by a strong ionization dielectric barrier discharge(DBD) lowtemperature plasma with large volume was explored. High concentration of hydroxyl radical(·OH)(0.74 mmol l-1) and ozone(O3)(58.2 mg l-1) produced by strongly ionized discharge DBD system were quantitatively analyzed based on the results of electron spin resonance and O3 measurements. The influencing reaction conditions of input voltages, initial p H value, ·OH inhibitors, initial concentration and inorganic ions on the removal efficiency of quinoline were systematically studied. The obtained results showed that the removal efficiency and TOC removal of quinoline achieved 94.8% and 32.2%, degradation kinetic constant was 0.050 min-1 at 3.8 k V and in a neutral p H(7.2). The proposed pathways of quinoline were suggested based on identified intermediates as hydroxy pyridine, fumaric acid, oxalic acid, and other small molecular acids by high-performance liquid chromatography/tandem mass spectrometry analysis. Moreover, the toxicity analysis on the intermediates demonstrated that its acute toxicity, bioaccumulation factor and mutagenicity were reduced. The overall findings provided theoretical and experimental basis for the application of a high capacity strong ionization DBD water treatment system in the removal of quinoline from drinking water.     

Removal of NO and SO2 in Corona Discharge Plasma Reactor with Water Film

In this paper, a novel type of a corona discharge plasma reactor was designed, which consists of needle-plate-combined electrodes, in which a series of needle electrodes are placed in a glass container filled with flue gas, and a plate electrode is immersed in the water. Based on this model, the removal of NO and SO2 was tested experimentally. In addition, the effect of streamer polarity on the reduction of SO2 and NO was investigated in detail. The experimental results show that the corona wind formed between the high-voltage needle electrode and the water by corona discharge enhances the cleaning efficiency of the flue gas because of the presence of water, and the cleaning efficiency will increase with the increase of applied dc voltage within a definite range. The removal efficiency of SO2 up to 98%, and about 85% of NO~ removal under suitable conditions is obtained in our experiments.     

Synthesis of Cu-Doped Mixed-Phase TiO2 with the Assistance of Ionic Liquid by Atmospheric-Pressure Cold Plasma

An atmospheric-pressure dielectric barrier discharge(DBD) gas-liquid cold plasma was employed to synthesize Cu-doped TiO_2 nanoparticles in an aqueous solution with the assistance of[C_2MIM]BF_4 ionic liquid(IL) and using air as the working gas.The influences of the discharge voltage,IL and the amount of copper nitrite were investigated.X-ray diffraction,N_2adsorption-desorption measurements and UV-Vis spectroscopy were adopted to characterize the samples.The results showed that the specific surface area of TiO_2 was promoted with Cu-doping(from 57.6 m~2·g~(-1) to 106.2 m~2·g~(-1) with 3%Cu-doping),and the content of anatase was increased.Besides,the band gap energy of TiO_2 with Cu-doping decreased according to the UV-Vis spectroscopy test.The 3%Cu-IL-TiO_2 samples showed the highest efficiency in degrading methylene blue(MB) dye solutions under simulated sunlight with an apparent rate constant of 0.0223 min~(-1),which was 1.2 times higher than that of non-doped samples.According to the characterization results,the reasons for the high photocatalytic activity were discussed.     

Temporal evolution of atmospheric cascade glow discharge with pulsed discharge and radio frequency discharge

Atmospheric cascade discharges with pulsed discharge and radio frequency(RF)discharge were experimentally investigated by the temporal evolution of discharge spatial profile and intensity.The indium tin oxide(ITO)coated glass was employed as the transparent electrode to capture the discharge distribution above the electrode surface.It is demonstrated that in the pulsed discharge with dielectric barrier,the first discharge at the rising edge of pulse voltage is uniformly ignited and then forms an expanding plasma ring on the ITO electrode surface,which shrinks to the same diameter as that of bare stainless steel electrode with the generation of second discharge at the falling edge of pulse voltage.The discharge profiles along the electrode surface and discharge gap of the successive RF discharge are dependent on the intensity and spatial distribution of residual plasma species generated by the pulsed discharge,which is determined by the time interval between the pulsed discharge and RF discharge.It is demonstrated that the residual plasma species before the RF discharge ignition help to achieve the stable operation of RF discharge with elevated intensity.     

Spectroscopic diagnosis of plasma in atmospheric pressure negative pulsed gasliquid discharge with nozzle-cylinder electrode

The plasma characteristics of a gas-liquid phase discharge reactor were investigated by optical and electrical methods.The nozzle-cylinder electrode in the discharge reactor was supplied witha negative nanosecond pulsed generator.The optical emission spectrum diagnosis revealed that OH(A~2∑~+?→?X~2Π,306–309 nm),N~3_2(CΠ→B~3Π_g,337 nm),O(3p~5p→3s~5s~0,777.2 nm)and O(3p~3p→3s~3s~0,844.6 nm)were produced in the discharge plasma channels.The electron temperature(T_e)was calculated from the emission relative intensity ratio between the atomic O 777.2 nm and 844.6 nm,and it increased with the applied voltage and the pulsed frequency and fell within the range of 0.5–0.8 e V.The gas temperature(T_g)that was measured by Lifbase was in a range from 400 K to 600 K.     

Study on the plasma generation characteristics of an induction-triggered coaxial pulsed plasma thruster

At present,spark plugs are used to trigger discharge in pulsed plasma thrusters (PPT),which are known to be life-limiting components due to plasma corrosion and carbon deposition.A strong electric field could be formed in a cathode triple junction (CTJ) to achieve a trigger function under vacuum conditions.We propose an induction-triggered electrode structure on the basis of the CTJ trigger principle.The induction-triggered electrode structure could increase the electric field strength of the CTJ without changing the voltage between electrodes,contributing to a reduction in the electrode breakdown voltage.Additionally,it can maintain the plasma generation effect when the breakdown voltage is reduced in the discharge experiments.The induction-triggered electrode structure could ensure an effective trigger when the ablation distance of Teflon increases,and the magnetic field produced by the discharge current could further improve the plasma density and propagation velocity.The induction-triggered coaxial PPT we propose has a simplified trigger structure,and it is an effective attempt to optimize the micro-satellite thruster.     

Wire-to-Plate Surface Dielectric Barrier Discharge and Induced Ionic Wind

The electrical and mechanical characteristics of the wire-to-plate surface dielectric barrier discharge and the induced ionic wind are investigated experimentally.The different temporal behaviors in positive and negative half-cycles are studied by time-resolved images.It is shown that the discharge and the light emission are generally stronger in the positive half cycle.The discharge is inhomogeneous and propagates in streamer mode;however,in the negative half-cycle,the discharge appears visually uniformly and operates in the diffuse mode.The surface discharge can produce ionic wind about several m/s above the dielectric surface.There exists an optimal width of the grounded electrode to produce a larger plasma area or active wind region.Increasing of the applied voltage or normalized dielectric constant leads to a larger wind velocity.The performance of ionic wind on flow control is visualized by employing a smoke stream.     

Activation of peroxydisulfate by gas-liquid pulsed discharge plasma to enhance the degradation of p-nitrophenol

Pulsed discharge in water and over water surfaces generates ultraviolet radiation,local high temperature,shock waves,and chemical reactive species,including hydroxyl radicals,hydrogen peroxide,and ozone.Pulsed discharge plasma (PDP) can oxidize and mineralize pollutants very efficiently,but high energy consumption restricts its application for industrial wastewater treatment.A novel method for improving the energy efficiency of wastewater treatment by PDP was proposed,in which peroxydisulfate (PDS) was added to wastewater and PDS was activated by PDP to produce more strong oxidizing radicals,including sulfate radicals and hydroxyl radicals,leading to a higher oxidation capacity for the PDP system.The experimental results show that the increase in solution conductivity slightly decreased the discharge power of the pulse discharge over the water surface.An increase in the discharge intensity improved the activation of PDS and therefore the degradation efficiency and energy efficiency of p-nitrophenol (PNP).An increase in the addition dosage of PDS greatly facilitated the degradation of PNP at a molar ratio of PDS to PNP of lower than 80∶1,but the performance enhancement was no longer obvious at a dosage of more than 80∶1.Under an applied voltage of 20 kV and a gas discharge gap of 2 rmm,the degradation efficiency and energy efficiency of the PNP reached 90.7％ and 45.0 mg kWh-1 for the plasma/PDS system,respectively,which was 34％ and 18.0 mg kWh-1 higher than for the discharge plasma treatment alone.Analysis of the physical and chemical effects indicated that ozone and hydrogen peroxide were important for PNP degradation and UV irradiation and heat from the discharge plasma might be the main physical effects for the activation of PDS.