Microstructural Observations on Hot-Pressed Si3N4

The development of microstructure in hot-pressed Si_aN₄ was studiehd for a typical Si₃N₄ powder with and without BeSiN₂ as a densification aid. The effect of hot-pressing temperature on density, α- to β-Si₃N₄ conversion and specific surface area showed that BeSiN₂ appears to increase the mobility of the system by enhancing densification, α- to β-Si₃N₄ transformation, and grain growth at temperatures between 1450° and 1800°. These processes appear to occur in the presence of a liquid phase.     

Phase Relations in the Si3N4-Rich Portion of the Si3N4–AlN–Al2O3–Y2O3

The phase relations in the Si₃N₄-rich portion of the Si₃N₄–AlN–Y₂O₃ rystem were investigated using hot-pressed bodies. The one-phase fields of β3 and α, the twophase fields of β+α, β+M (M=melilite), and α+M, and the three-phase fields of β+α+M were observed in the Si₃N₄-rich portion. The α- and β-sialons are not two different compounds but an allotropic transformation phase of the Si–Al–O–N system, and an α solid solution expands and stabilizes with increasing Y₂O₃ content. Therefore, the formulas of the two sialons should be the same.     

Microstructure and Mechanical Properties of the in situβ-Si3N4/α'-SiAlON Composite

The in situ β-Si₃N₄/α'-SiAlON composite was studied along the Si₃N₄–Y₂O₃: 9 AlN composition line. This two phase composite was fully densified at 1780°C by hot pressing Densification curves and phase developments of the β-Si₃N₄/α'-SiAlON composite were found to vary with composition. Because of the cooperative formation of α'-Si AlON and β-Si₃N₄ during its phase development, this composite had equiaxed α'-SiAlON (∼0.2 μm) and elongated β-Si₃N₄ fine grains. The optimum mechanical properties of this two-phase composite were in the sample with 30–40%α', which had a flexural strength of 1100 MPa at 25°C 800 MPa at 1400°C in air, and a fracture toughness 6 Mpa·m^1/2. α'-SiAlON grains were equiaxed under a sintering condition at 1780°C or lower temperatures. Morphologies of the α°-SiAlON grains were affected by the sintering conditions.     

High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Synthesis, Characterization, and Consolidation of Si3N4 Obtained from Ammonolysis of SiCl4

Thermal decomposition of silicon diimide, Si(NH)₂, in vacuum resulted in very-high-purity, fine-particle-size, amorphous Si₃N₄ powders. The amorphous powder was isothermally aged at 50° to 100° intervals from 1000° to 1500°C for phase identification. Examination of ir spectra and X-ray diffraction patterns indicated a slow and gradual transition from an amorphous material to a crystalline α-phase occurring at 1200°C for >4 h and/or 1300° to 1400°C for 2 h. As the temperature was increased to ≥1450°C for 2 h, the crystalline β-phase was observed. Phase nucleation and crystallite morphology in this system were studied by electron microscopy and electron diffraction combined with TG as functions of temperature for the inorganic polymer starting materials. Powders prepared in this manner with 4 wt% Mg₃N₂ added as a sintering aid were hot-pressed to high-density fine-grained bodies with uniform microstructures. The optimum hot-pressing condition was 1650°C for 1 h. Silicon concentration steadily increased as the hot-pressing temperature or time was increased. A method for chemical etching for high-density fine-grained Si₃N₄ is described. Electrical measurements between room temperature and ∼500°C indicated dielectric constant and tan δ values of 8.3±0.03 and 0.65±0.05×10⁻², respectively.     

Impurity Phases in Hot-Pressed Si3N4

Impurity phases in commercial hot-pressed Si₃N₄ were investigated using transmission electron microscopy. In addition to the dominant, β-Si₃N₄ phase, small amounts of Si₂N₂O, SiC, and WC were found. Significantly, a continuous grain-boundary phase was observed in the ∼ 25 high-angle boundaries examined. This film is ∼ 10 Å thick between, β-Si₃N₄ grains and ∼ 30 Å thick between Si₂N₂O and β-Si₃N₄ grains.     

Fabrication of Si3N4/SiC Composite by Reaction-Bonding and Gas-Pressure Sintering

Si₃N₄/SiC composite materials have been fabricated by reaction-sintering and postsintering steps. The green body containing Si metal and SiC particles was reaction-sintered at 1370°C in a flowing N₂/H₂ gas mixture. The initial reaction product was dominated by alpha-Si₃N₄. However, as the reaction processed there was a gradual increase in the proportion of β-Si₃N₄. The reaction-bonded composite consisting of alpha-Si₃N₄, β-Si₃N₄, and SiC was heat-treated again at 2000°C for 150 min under 7-MPa N₂ gas pressure. The addition of SiC enhanced the reaction-sintering process and resulted in a fine microstructure, which in turn improved fracture strength to as high as 1220 MPa. The high value in flexural strength is attributed to the formation of uniformly elongated β-Si₃N₄ grains as well as small size of the grains (length = 2 μm, thickness = 0.5 μm). The reaction mechanism of the reaction sintering and the mechanical properties of the composite are discussed in terms of the development of microstructures.     

Effect of Porosity and Microstructure on the Strength of Si3N4: Designed Microstructure for High Strength, High Thermal Shock Resistance, and Facile Machining

The flexural strength of porous Si₃N₄ ceramics with a variety of microstructures and porosities were evaluated, and the effect of microstructure on the flexural strength was investigated to obtain machinable Si₃N₄ ceramics having both high strength and high thermal shock resistance. Porous Si₃N₄ having three types of microstructure, consisting of (1) only spherical grains, (2) combinations of spherical and columnar grains, and (3) only columnar β-grains connected randomly in three dimensions, were readied as specimens. Their mean pore diameters and porosities were 0.2 to 0.3 μm and 8% to 59%, respectively. The flexural strength of the porous Si3N4 (3) was much larger than that of the porous Si3N4 having the other microstructures, and the maximum flexural strength was 455 MPa at a porosity of 38.3%. The thermal shock resistance (ΔT), which was determined by a water quench test, of porous Si₃N₄ with such microstructure and a porosity of 50% was 980 K. All of the porous Si₃N₄ (3) was easily machined with cemented carbide drills.     

Residual α–Si3N4 in O' Crystals in CeO2-Doped O'+β' SiAlON Ceramics

The microstructure of a pressureless sintered (1605°C, 90 min) O'+β' SiAlON ceramic with CeO₂ doping has been investigated. It is duplex in nature, consisting of very large, slablike elongated O' grains (20–30 μm long), and a continuous matrix of small rodlike β' grains (< 1.0 μm in length). Many α-Si₃N₄ inclusions (0.1–0.5 μm in size) were found in the large O' grains. CeO₂-doping and its high doping level as well as the high Al₂O₃ concentration were thought to be the main reasons for accelerating the reaction between the α-Si₃N₄ and the Si-Al-O-N liquid to precipitate O'–SiAlON. This caused the supergrowth of O' grains. The rapid growth of O' crystals isolated the remnant α–Si₃N₄ from the reacting liquid, resulting in a delay in the α→β-Si₃N₄ transformation. The large O' grains and the α-Si₃N₄ inclusions have a pronounced effect on the strength degradation of O'+β' ceramics.     

Fabrication of Hard and Strong α/β-Si3N4 Composites With MgSiN2 as Addivitives

α/β-Si₃N₄ composites with various α/β phase ratios were prepared by hot pressing at 1600°–1650°C with MgSiN₂ as sintering additives. An excellent combination of mechanical properties (Vickers indentation hardness of 23.1 GPa, fracture strength of about 1000MPa, and toughness of 6.3 MPa·m^1/2) could be obtained. Compared with conventional Si₃N₄-based ceramics, this new material has obvious advantages. It is as hard as typical in-situ-reinforced α-Sialon, but much stronger than the latter (700 MPa). It has comparable fracture strength and toughness, but is much harder than β-Si₃N₄ ceramics (16 GPa). The microstructures and mechanical properties can be tailored by choosing the additive and controlling the heating schedule.     

Phase Equilibria in the System Si3N4-SiO2-BeO-Be3N2

The 1780°C isothermal section of the reciprocal quasiternary system Si₃N₄-SiO₂-BeO-Be₃N₂ was investigated by the X-ray analysis of hot-pressed samples. The equilibrium relations shown involve previously known compounds and 8 newly found compounds: Be₆Si³N₈, Be₁₁Si₅N₁₄, Be₅Si²N₆, Be₉Si₃N₁₀, Be₈SiO₄N₄, Be₆O₃N₂, Be₈O₅N₂, and Be₉O₆N₂. Large solid solubility occurs in β-Si₃N₄, BeSiN₂, Be₉Si₃N₁₀, Be₄SiN₄, and β-Be₃N₂. Solid solubility in β-Si₃N₄ extends toward Be₂SiO₄ and decreases with increasing temperature from 19 mol% at 1770°C to 11.5 mol% Be₂SiO₄ at 1880°C. A 4-phase isotherm, liquid +β-Si₃N₄ ( ss )Si₂ON₂+ BeO, exists at 1770°C.     

Relationship between Microstructure and Mechanical Performance of a 70% Silicon Nitride–30% Barium Aluminum Silicate Self-Reinforced Ceramic Composite

The abnormal grain growth of β-Si₃N₄ was observed in a 70% Si₃N₄–30% barium aluminum silicate (70%-Si₃N₄–30%-BAS) self-reinforced composite that was pressureless-sintered at 1930°C; Si₃N₄ starting powders with a wide particle-size distribution were used. The addition of coarse Si₃N₄ powder encouraged the abnormal growth of β-Si₃N₄ grains, which allowed microstructural modification through control of the content and size distribution of β-Si₃N₄ nuclei. The mechanical response of different microstructures was characterized in terms of flexural strength, as well as indentation fracture resistance, at room temperature. The presence of even a small amount of abnormally grown β-Si₃N₄ grains improved the fracture toughness and minimized the variability in flexural strength.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

A Theoretical Estimate of Solution-Precipitation Creep in MgO-Fluxed Si3N4

The creep rate in MgO-fluxed hot-pressed Si₃N₄ is calculated by means of a model which assumes a solution-precipitation mechanism, and by using the kinetic data for the dissolution rate of β-Si₃N₄ in an Mg-Si-O-N glass (which was obtained in independent experiments). Despite simplifying assumptions, the predictions match quite favorably with experimental measurements of creep in hot-pressed Si₃N₄.     

Combustion Synthesis of Si3N4 by Selective Reaction of Silicon with Nitrogen in Air

Silicon nitride (Si₃N₄) was synthesized by a selective combustion reaction of silicon powder with nitrogen in air. The α/β-Si₃N₄ ratio of the interior product could be tailored by adjusting the Si₃N₄-diluent content in the reactant mixtures. The synthetic β-Si₃N₄ showed a well-crystallized rod-like morphology. Mechanical activation greatly enhanced the reactivity of silicon powder, and the slow oxidation of silicon at the sample surface promoted the combustion reaction in air. The formation mechanism of Si₃N₄ was analyzed based on a proposed N₂/O₂ diffusion kinetic model, and the calculated result is in good agreement with the experimental phenomenon.     

Additive-Assisted Nitridation to Synthesize Si3N4 Nanomaterials at a Low Temperature

Starting from Si powder, NaN₃ and different additives such as N -aminothiourea, iodine, or both, Si₃N₄ nanomaterials were synthesized through the nitridation of silicon powder in autoclaves at 60°–190°C. As the additive was only N -aminothiourea, β-Si₃N₄ nanorods and α-Si₃N₄ nanoparticles were prepared at 170°C. If the additive was only iodine, α-Si₃N₄ dendrites with β-Si₃N₄ nanorods were obtained at 190°C. However, when both N -aminothiourea and iodine were added to the system of Si and NaN₃, the products composed of β-Si₃N₄ nanorods and α, β-Si₃N₄ nanoparticles could be prepared at 60°C.     

Microstructural Characterization and Mechanical Properties of Si3N4 Formed by Fused Deposition of Ceramics

We present processing (green and sintered), part shrinkage and warping, microstructural characterization, and mechanical properties of Si₃N₄ made by fused deposition of ceramics (FDC), using optical microscopy, scanning electron microscopy, and X-ray diffraction. The mechanical properties (fracture strength, fracture toughness, and Weibull modulus) are also reported. Proper FDC build parameters resulted in dense, homogeneous, near-net-shape Si₃N₄, with microstructures and mechanical properties similar to conventionally processed material. Mechanical properties are shown to be isotropic, while there is some degree of microstructural texturing (preferred β-Si₃N₄ grain orientation) in sintered components.     

Combustion Synthesis of Si3N4–SiC Composite Powders

Fine Si₃N₄-SiC composite powders were synthesized in various SiC compositions to 46 vol% by nitriding combustion of silicon and carbon. The powders were composed of α-Si₃N₄, β-Si₃N₄, and β-SiC. The reaction analysis suggested that the SiC formation is assisted by the high reaction heat of Si nitridation. The sintered bodies consisted of uniformly dispersed grains of β-Si₃N₄, β-SiC, and a few Si₂N₂O.     

Hot Isostatic Pressing of Si3N4 Powder Compacts and Reaction-Bonded Si3N4

Hot isostatically pressed silicon nitride was produced by densifying Si₃N₄ powder compacts and reaction-bonded Si₃N₄ (RBSN) parts with yttria as a sintering additive. The microstructure was analyzed using scanning electron microscopy, X-ray diffraction, and density measurements. The influence of the microstructure on fracture strength, creep, and oxidation behavior was investigated. It is assumed that the higher amount of oxygen in the Si₃N₄ starting powder compared with the RBSN starting material leads to an increased amount of liquid phase during densification. This results in grain growth and in a larger amount of grain boundary phase in the hot isostatically pressed material. Compared with the hot isostatically pressed RBSN samples therefore, strength decreases whereas the creep rate and the weight gain during oxidation increase.     

Influence of Phase Formation on Dielectric Properties of Si3N4 Ceramics

The influence of phase formation on the dielectric properties of silicon nitride (Si₃N₄) ceramics, which were produced by pressureless sintering with additives in MgO–Al₂O₃–SiO₂ system, was investigated. It seems that the difference in the dielectric properties of Si₃N₄ ceramics sintered at different temperatures was mainly due to the difference of the relative content of α-Si₃N₄, β-Si₃N₄, and the intermediate product (Si₂N₂O) in the samples. Compared with α-Si₃N₄ and Si₂N₂O, β-Si₃N₄ is believed to be a major factor influencing the dielectric constant. The high-dielectric constant of β-Si₃N₄ could be attributed to the ionic relaxation polarization.