共查询到20条相似文献,搜索用时 62 毫秒
1.
双辽发电厂1、2号机的三台“半容量”给水泵选用二台汽动给水泵和一台电动给水泵的组合形式。电动给水泵作为二台汽动泵的备用泵,在启动、停机和汽动泵事故状态下使用,选用的是北京电力设备总厂的产品。 小汽机型号:GT—03B 给水泵型号:HPTMK200—320 前置泵型号:ZER250—5560 二台机组的汽动给水泵在分部试运中 相似文献
2.
1主给水泵和联备给水泵 300MW机组的给水系统中安装了2台汽动给水泵(由小汽轮机带动运转)和1台电动给水泵(由电动机及增速齿轮箱带动运转)。汽动给水泵称为主给水泵,也就是正常运行中,2台汽动给水泵同时并联运行。电 相似文献
3.
(1)合肥第二发电厂汽轮发电机组配用二台汽动给水泵、一台电动给水泵,其流量分别为697t/h和409.4t/h,分别承担机组额定出力的50%和35%。机组正常运行时二台汽动给水泵运行,电动给水泵在机组启停时投运,并作为汽动给水泵异常时的备用给水泵。 相似文献
4.
大型火电机组给水泵一般采用小汽机驱动,研究小汽机耗汽量、小汽机相对内效率、给水泵效率、给水泵焓升之间的相互关系及其对机组经济性的影响.依据热力学基本原则,建立了汽动给水泵组参量间的相互关系;建立了相应的满足热力学原理的热平衡分析模型和适用于局部定量的等效焓降分析模型;分析了给水泵焓升是否计入以及给水泵效率及小汽机相对内效率变化对经济性的不同影响.算例一通过正反热平衡分析结果与等效焓降分析结果的一致性说明了模型的合理性与准确性;算例二揭示了给水泵效率与小汽机效率对机组经济性的不同影响,为汽动给水泵系统的节能提供依据. 相似文献
5.
国产300MW火电机组配有两台汽动给水泵和一台电动给水泵,每台泵的给水流量均能满足50%额定负荷。前者作为正常运行用,后者作为起动和停机用,也作为汽动给水泵的备用。为了确定汽动给水泵的改进效果、检修质量以及制定经济运行方式,需要能较精确地测定其效率。然而,给水泵汽轮机(以下简称小汽机)的排汽为湿蒸汽,在电厂运行条件下无法确定排汽焓,算不出内功率。另外,即使求出了内功率,如果不能测出机械损失,也求不 相似文献
6.
7.
火电机组汽动给水泵,因由小汽机拖动,需要消耗做功蒸汽,因此对机组的热经济性有一定的影响。当机组工况发生变化时,汽动给水泵间通过流量分配,降低对机组热经济的影响。以亚临界600 MW和超超临界1000 MW机组为例,在某负荷区及忽略给水泵的管道水力特性影响的情况下,基于两台给水泵不同流量分配方案,分析和比较机组的热经济性,并以此确定给水泵的最佳运行方式。结果表明:随着两台汽动给水泵的给水流量逐渐接近,在不同工况下,机组的第三段抽汽量减少,第四段抽汽量增加,汽轮机总体做功蒸汽增加,使机组标准煤耗率降低、热效率提高;当两台给水泵分配的流量相等时,机组的热经济性最佳,即为给水泵系统最佳运行方式,对实际运行机组有一定的参考意义。 相似文献
8.
9.
CHTA型给水泵是沈阳水泵厂引进西德KSB公司专利技术自行制造的锅炉汽动给水泵。从谏壁、洛河发电厂300MW机组和平圩发电厂600MW机组启动调试的情况看,小汽机停机后进行连续盘车时,该类给水泵在热态工况下泵芯容易卡煞,为此,需要进行拆卸检修。正确进行该类汽动给水泵的热态盘车值得研究。 相似文献
10.
11.
12.
13.
Yuan Chen Westergard L. Mojarradi M.M. Johnson T.W. Cozy R.S. Billman C. Burke G.R. Kolawa E.A. 《Device and Materials Reliability, IEEE Transactions on》2006,6(2):146-153
A design for reliability methodology has been developed for electronics for low-temperature applications. A hot carrier aging (HCA) lifetime projection model is proposed to take into account the HCA impact on technology, analysis of parametric degradation versus critical circuit path degradation, transistor bias profile, transistor substrate current profile, and operating temperature profile. The most applicable transistor size can be determined in order to meet the reliability requirements of the electronics operating under low temperatures. This methodology and approach can also be applied to other transistor-level failure and/or degradation mechanisms for applications with varying temperature ranges. 相似文献
14.
15.
《Power Delivery, IEEE Transactions on》1998,13(1):73-77
IEEE Standard 1344, Synchrophasors for Power Systems, was completed in 1995. It sets parameters required to ensure that phasor measurement will be made and communicated in a consistent manner. It specifies requirements for the timing signal used for phasor synchronization and the time code needed for input to a measurement unit. GPS is the recommended time source and IRIG-B is the basic format used for time communication. The standard requires correlating phasors computed from unsynchronized and synchronized sampling to a common basis. Timetagging accurately and consistently is essential for wide area comparison of phase. The standard specifies information exchange and control message formats. These include data output, configuration, and command messages. It includes 7 annexes that discuss the concepts covered in the body of the standard 相似文献
16.
17.
18.
19.
20.
分析了GIS断路器故障原因,介绍了检验过程与充气检查、监督情况,并提供一些可借鉴的成功经验。 相似文献