Piezoelectric Properties of Pb(Mg1/3Nb2/3)O3 PbTiO3 -PbZrO3 Ceramics Modified with Certain Additives

Effects of additives on the piezoelectric properties of Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃-PbZrO₃ ceramics in a perovskite-type structure are described. The tetragonality of Pb(Mg_1/3Nb_2/3)_0.375-Ti_0.375Zr_0.25O₃ ceramics increased with the addition of NiO, Cr₂O₃, or Fe₂O₃ but decreased with the addition of MnO₂ or CoO. The dielectric and piezoelectric properties of the base composition were improved markedly through selection of additives in proper amounts. Addition of NiO yielded a high dielectric constant and planar coupling coefficient for compositions at the morphotropic transition boundary. High mechanical Q -factors and low electrical dissipation factors were obtained by addition of MnO₂. Addition of both NiO and MnO₂ produced a mechanical Q -factor of 2051 and a planar coupling coefficient of 0.553. The resonant frequency of Pb(Mg_1/2Nb_2/3)_0.4375Ti_0.4375 zr_0.125O₃ containing MnO₂ had very low temperature and time dependence. The microstructure indicated that ceramics with a high mechanical Q -factor had a fine, uniform grain structure. Addition of Cr₂O₃ retarded grain growth and addition of MnO₂, NiO, CoO, or Fe₂O₃ promoted grain growth in the ternary system.     

Effect of MnO2 Addition on the Structure and Electrical Properties of Pb(Zn1/3Nb2/3)0.20(Zr0.50Ti0.50)0.80O3 Ceramics

Pb(Zn_1/3Nb_2/3)_0.20(Zr_0.50Ti_0.50)_0.80O₃ ceramics of pure perovskite structure were prepared by the two-stage method with the addition of 0–3.0 wt% MnO₂ and their piezoelectric properties were investigated systematically. The MnO₂ addition influences in a pronounced way both the crystal structure and the microstructure of the materials. The materials are transformed from the tetragonal to the rhombohedral structure, and the grain size is enhanced when manganese cations are added. The distortion of crystal structure for samples with MnO₂ addition can be explained by the Jahn–Teller effect. The values of electromechanical coupling factor ( k _p) and dielectric loss (tan δ) are optimized for 0.5-wt%-MnO₂-doped samples ( k _p= 0.60, tan δ= 0.2%) and the mechanical quality factor ( Q _m) is maximized for 1.0-wt%-MnO₂-doped samples ( Q _m= 1041), which suggests that oxygen vacancies formed by substituting Mn³⁺ and Mn²⁺ ions for B-site ions (e.g., Ti⁴⁺ and Zr⁴⁺ ions) in the perovskite structure partially inhibited polarization reversal in the ferroelectrics. The ceramics with 0.50–1.0 wt% MnO₂ addition show great promise as practical materials for piezoelectric applications.     

Fabrication and Tunable Dielectric Properties of (Ba0.7Sr0.3)TiO3-Glass-Based Thick-Film Capacitors

Ferroelectric glass–ceramics of composition 0.90 (Ba_0.7Sr_0.3) TiO₃–0.10(B₂O₃:SiO₂) (0.90 BST:0.10 BS) synthesized by sol–gel method have been used for the preparation of dielectric thick-film inks. The particle dispersion of the glass–ceramic powders in the thick-film ink formulations have been studied through rheological measurements for fabricating thick-film capacitors by screen printing technique. The thick films derived from such glass–ceramics are found to sinter at considerably lower temperatures than the pure ceramic, and exhibit good dielectric characteristics with a tunability of 32% at 1 MHz under a dc bias field of 35 kV/cm.     

Effect of Nb2O5/ZnO Addition on Microwave Properties of (Zr0.8Sn0.2)TiO4 Ceramics

The effects of Nb₂O₅ and ZnO addition on the dielectric properties, especially the quality factor, of (Zr_0.8Sn_0.2)TiO₄ (ZST) ceramics were investigated in terms of the sintered density acquired by the zinc. For ZST ceramics with 2 mol% added ZnO, the relative density of the samples decreased with >0.5 mol% addition of Nb₂O₅. On the other hand, for samples with 6 mol% added ZnO, the relative density remained >97%, even when the amount of Nb₂O₅ was increased to 2.0 mol%. When >0.5 mol% Nb₂O₅ was added, both the quality factor and the dielectric constant exhibited similar trends with sintered density. The ZST ceramics with 6 mol% added ZnO, especially, still manifested a quality factor >40 000 and a dielectric constant of 37, even when the amount of Nb₂O₅ was increased, values that are not explainable by the previously suggested electronic defect model.     

(Bi1/2Na1/2)TiO3–Ba(Cu1/2W1/2)O3 Lead-Free Piezoelectric Ceramics

(Bi_1/2Na_1/2)TiO₃ with 0–6 mol% Ba(Cu_1/2W_1/2)O₃ (BNT-BCW), a new member of the BNT-based group, has been prepared following the conventional mixed oxide route. The compacted bodies were sintered at 1130°C for 2 h to get dense ceramics. The addition of BCW into BNT ceramics facilitated the poling process because of a reduction in leakage current. 0.995BNT·0.005BCW ceramics exhibit a relatively high piezoelectric constant ( d ₃₃= 80 × 10⁻¹² C/N) and a relatively low dielectric loss (tan δ= 1.5%). Increased amount of BCW was found to increase the dielectric constant and loss of BNT-BCW ceramics and to suppress the grain growth. During sintering, some BCW diffuses into the lattice of BNT to form a solid solution and some remains on the grain boundaries.     

Electrical Properties of Sr0.7Ba0.3TiO3 Ceramics Doped with Nb2O5, 3Li2O · 2SiO2, and Bi2O3

The electrical properties of Sr_0.5Ba_0.3TiO₃ in the presence of Nb₂O₅ as a donor, 3Li₂O · 2SiO₂ as a sintering agent, and Bi₂O₃ as a dopant have been studied. When the compositions of the ceramics were 1 mol Sr_0.7Ba_0.3TiO₃+ 0.5 mol% Nb₂O₅+ 2 mol% 3Li₂O · 2SiO₂+ 0.2 mol% Bi₂O₃, the ceramics were sintered at 1100°C and exhibited the following characteristics: apparent dielectric constant ɛ, 25000; loss factor tan δ, 2%; insulating resistivity ρ_j, 10¹⁰Ω· cm; variation of dielectric constant with temperature Δɛ/ɛ (−25° to +85°C), +10%, −14%. ɛ and tan δ show only small changes with frequency. The study shows this ceramic can be used in multilayer technology.     

The Systems PbF2-AlF3 and CaF2-AlF3

The compound Pb₃Al₂FI₁₂ is reported in the system PbF₂-AIF₃. It is tetragonal, I 4/m, d₀ = 14.23 å, c_o = 7.20 Å. A phase diagram for the system is presented on the basis of DTA and X-ray Powder Patterns. The compound melts incongruently at 649°C. Solid solubility of AlF₃ in PbF₂ occurs with up to 15 mol% AlF₃. Data for the system CaF₂-A1F₃ is compared with previous reports.     

Electromechanical Properties of Pb(Yb1/2Nb1/2)O3-PbZrO3-PbTiO3 Ceramics

The electromechanical and electric-field-induced strain properties of x Pb(Yb_1/2Nb_1/2)O₃· y PbZrO₃·(1− x − y )PbTiO₃ ( x = 0.12, 0.25, 0.37; y = 0.10–0.40) ceramics have been studied systematically as a function of Pb(Yb_1/2Nb_1/2)O₃ (PYN) content and PbZrO₃/PbTiO₃ (PZ/PT) ratio. In addition, the effect of MnO₂ on the electromechanical properties of 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ was also investigated. The maximum transverse strain values of 1.6 × 10⁻³ for x = 0.12, 1.45 × 10⁻³ for x = 0.25, and 1.36 × 10⁻³ for x = 0.37 were obtained at the compositions which were regarded as the morphotropic phase boundary (MPB). The transverse strain was maximized at the MPB composition. The value of the maximum electromechanical coupling coefficient was 0.69 for y = 0.40 and x = 0.12 composition. In the 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ composition, the temperature of the maximum dielectric constant decreased and the grain size increased with an addition of MnO₂. The electromechanical coupling coefficient decreased while the mechanical quality factor rapidly increased with an addition of MnO₂. These resulted mainly from the acceptor effect of manganese ions that were produced by doping MnO₂ into the perovskite structure.     

Phase Transitions and Electrical Properties of (Na1−xKx)(Nb1−ySby)O3 Lead-Free Piezoelectric Ceramics With a MnO2 Sintering Aid

Lead-free piezoelectric ceramics (Na_{1− x} K _x )(Nb_{1− y} Sb _y )O₃+ z mol% MnO₂ have been prepared by a conventional solid-state sintering technique. Our results reveal that Sb⁵⁺ diffuses into the K_0.5Na_0.5NbO₃ lattices to form a solid solution with a single-phase orthorhombic perovskite structure. The partial substitution of Sb⁵⁺ for B-site ion Nb⁵⁺ decreases the paraelectric cubic-ferroelectric tetragonal phase transition ( T _c) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition ( T _O–F), and retains strong ferroelectricity. A small amount of MnO₂ is enough to improve the densification of the ceramics. The co-effects of MnO₂ doping and Sb substitution lead to significant improvements in ferroelectric and piezoelectric properties. The ceramics with x =0.45–0.525, y =0.06–0.08, and z =0.5–1 exhibit excellent ferroelectric and piezoelectric properties: d ₃₃=163–204 pC/N, k _P=0.47–0.51, k _t=0.46–0.52, ɛ=640–1053, tan δ=1.3–3.0%, P _r=18.1–22.6 μC/cm², E _c=0.72–0.98 kV/mm, and T _C=269°–314°C.     

Microwave Dielectric Properties and Low-Temperature Sintering of Ba0.60Sr0.40TiO3 Ceramics

In the present work, the sintering behaviors and dielectric properties of Ba_0.60Sr_0.40TiO₃ (BST) ceramics with the addition of BaCu(B₂O₅) were investigated in detail. The results indicated that the addition reduced the sintering temperature of BST by about 500°C. It was suggested that a liquid phase BaCu(B₂O₅) assisted the densification of BST ceramics at lower temperatures. For a low-level BaCu(B₂O₅) addition (2.0 mol%), the BST sample sintered at 950°C for 5 h displayed good dielectric properties, with a moderate dielectric constant (ɛ=2553) and a low dielectric loss (tan δ=0.00305) at room temperature and at 10 kHz. The sample showed 45.9% tunability at 10 kHz under a dc electric field of 30 kV/cm. At the frequency of 0.984 GHz, BST-added 2.0 mol% BaCu(B₂O₅) possessed a dielectric constant of 2204 and a Q value of 146.7.     

Microwave Dielectric Properties of Doped BaTi4O9

Polycrystalline BaTi₄O₉ doped with Mn, Sn, Zr, Ca, Sr, and Pb was prepared from carbonates and oxides. Single-phase ceramics with densities exceeding 97% of theoretical were made with up to 3 mol% Mn; 6 mol% Sn, Zr, and Ca; and 8 mol% Sr and Pb. Dielectric constant, k , quality factor, Q , and temperature coefficient of frequency, τ _f , of ∼37, 5675, and 15 ppm/°C, respectively, were determined at 4 GHz for undoped BaTi₄O₉. Doping did not significantly affect k and τ _f . However, doping with Mn, Sn, and Pb lowered Q , whereas doping with Zr, Ca, and Sr increased Q by up to 2000. Additions of 0.5 mol% MnO₂ as a second phase improved Q from 3675 to 7600.     

Effect of Additives on the Electromechanical Properties of Pb(Zr,Ti)O3–Pb(Y2/3W1/3)O3 Ceramics

Dielectric and piezoelectric properties of 0.02Pb(Y_2/3W_1/3)O₃ 0.98Pb(Zr0.52Ti0.48)O3 ceramics doped with additives (Nb₂O₅, La₂O₃, MnO₂, and Fe₂O₃) were investigated. The grain sizes of these ceramics decreased with increasing amounts of additives. For additions of MnO₂ and Fe₂O₃, dielectric losses decreased, while for Nb₂O₅ and La₂O₃, these values increased. The maximum values of the mechanical quality factor Q_m were found to be 956 and 975 for additions of 0.9 wt% Fe₂O₃ and 0.7 wt% MnO₂, respectively, but donor dopants (Nb₂O₅ and La₂O₃) did not change the values of Q_m . On the other hand, the piezoelectric constant d₃₃ and the electromechanical coupling factor k_p decreased with additions of MnO₂ and Fe₂O₃, but improved with additions of Nb₂O₅ and La₂O₃.     

Dielectric and Ferroelectric Properties of Ceramics in the Pb(Zn 1/3Nb2/3)O3-BaTiO3-PbTiO3 System

The use of Pb(Zn_1/3Nb_2/3)O₃ ceramics is restricted by the formation of a pyrochlore phase detrimental to both dielectric and piezoelectric properties. Recently it has been shown that a 6 mol% addition of BaTiO₃ to PZN suppresses the formation of pyrochlore phase. Phase relations and dielectric properties of ceramics in the PZN-BT-PT system are reported here. Compositions with the perovskite structure, having high dielectric constant and low temperature coefficient of capacitance, have been identified.     

Lithium Ion-Conducting Glass–Ceramics of Li1.5Al0.5Ge1.5(PO4)3–xLi2O (x=0.0–0.20) with Good Electrical and Electrochemical Properties

NASICON-type structured Li_1.5Al_0.5Ge_1.5(PO₄)₃– x Li₂O Li-ion-conducting glass–ceramics were successfully prepared from as-prepared glasses. The differential scanning calorimetry, X-ray diffraction, nuclear magnetic resonance, and field emission scanning electron microscope results reveal that the excess Li₂O is not only incorporated into the crystal lattice of the NASICON-type structure but also exists as a secondary phase and acts as a nucleating agent to considerably promote the crystallization of the as-prepared glasses during heat treatment, leading to an improvement in the connection between the glass–ceramic grains and hence a dense microstructure with a uniform grain size. These beneficial effects enhance both the bulk and total ionic conductivities at room temperature, which reach 1.18 × 10⁻³ and 7.25 × 10⁻⁴ S/cm, respectively. In addition, the Li_1.5Al_0.5Ge_1.5(PO₄)₃–0.05Li₂O glass–ceramics display favorable electrochemical stability against lithium metal with an electrochemical window of about 6 V. The high ionic conductivity, good electrochemical stability, and wide electrochemical window of LAGP–0.05LO glass–ceramics suggest that they are promising solid-state electrolytes for all solid-state lithium batteries with high power density.     

Characteristics of High-Q Microwave Dielectric Ceramics Nd(Co1/2Ti1/2)O3 With CuO Addition

We report the microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ ceramics prepared by the conventional solid-state route. The prepared Nd(Co_1/2Ti_1/2)O₃ exhibits a mixture of Co and Ti showing a 1:1 order in the B site. Lowering the sintering temperature (as low as 1260°C) and promoting the densification of Nd(Co_1/2Ti_1/2)O₃ ceramics could be effectively achieved by adding CuO (up to 0.75 wt%). At 1350°C, Nd(Co_1/2Ti_1/2)O₃ ceramics with 0.5 wt% CuO addition possess a dielectric constant (ɛ_r) of 27.6, a Q × f value of 165 000 GHz (at 9 GHz), and a temperature coefficient of resonant frequency (τ_f) of −20 ppm/°C. By comparing with pure Nd(Co_1/2Ti_1/2)O₃ ceramics, incorporating additional CuO helps to render a dielectric material with a higher dielectric constant, a smaller τ_f value, and a 20% dielectric loss reduction, which makes it a very promising candidate for applications requiring low microwave dielectric loss.     

Electrical Conduction Properties of LaP3O9 Glass and Glass–Ceramics

Electrical conduction properties of undoped and 1 mol% Sr-doped LaP₃O₉ glasses and glass–ceramics were investigated over the temperature range of 673–1123 K. Both the materials showed relatively low conductivities in the glassy state. However, the conductivity of the Sr-doped LaP₃O₉ glass significantly increased with a heat treatment above the crystallization temperature, while the conductivity of the undoped LaP₃O₉ glass did not improve even after the heat treatment. It was concluded that crystallization of the Sr-doped LaP₃O₉ glass induced protonic conduction and thus enhanced the conductivity. Electrical conduction properties of the Sr-doped LaP₃O₉ glass–ceramic fundamentally resembled those of the sintered crystalline Sr-doped LaP₃O₉.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Effect of Li2CO3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Mg2V2O7 Ceramics

Li₂CO₃ was added to Mg₂V₂O₇ ceramics in order to reduce the sintering temperature to below 900°C. At temperatures below 900°C, a liquid phase was formed during sintering, which assisted the densification of the specimens. The addition of Li₂CO₃ changed the crystal structure of Mg₂V₂O₇ ceramics from triclinic to monoclinic. The 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic was well sintered at 800°C with a high density and good microwave dielectric properties of ɛ _r=8.2, Q × f =70 621 GHz, and τ_f=−35.2 ppm/°C. Silver did not react with the 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic at 800°C. Therefore, this ceramic is a good candidate material in low-temperature co-fired ceramic multilayer devices.     

Sintering and Electrical Properties of Lead-Free Na0.5K0.5NbO3 Piezoelectric Ceramics

Lead-free Na_0.5K_0.5NbO₃ (NKN) piezoelectric ceramics were fairly well densified at a relatively low temperature under atmospheric conditions. A relative density of 96%–99% can be achieved by either using high-energy attrition milling or adding 1 mol% oxide additives. It is suggested that ultra-fine starting powders by active milling or oxygen vacancies and even liquid phases from B-site oxide additives mainly lead to improved sintering. Not only were dielectric properties influenced by oxide additives, such as the Curie temperature ( T _c) and dielectric loss ( D ), but also the ferroelectricity was modified. A relatively large remanent polarization was produced, ranging from 16 μC/cm² for pure NKN to 23 μC/cm² for ZnO-added NKN samples. The following dielectric and piezoelectric properties were obtained: relative permittivity ɛ ^T ₃₃/ɛ ₀ =570–650, planar mode electromechanical coupling factor, k _p=32%–44%, and piezoelectric strain constant, d ₃₃=92–117 pC/N.     

Dielectric Properties of the Fluorite-like Bi2O3–Nb2O5 Solid Solution and the Tetragonal Bi3NbO7

Our analysis of the microwave dielectric properties of the δ-Bi₂O₃–Nb₂O₅ solid solution (δ-BN_ss) showed a continuous increase in permittivity and dielectric losses with an increasing concentration of Nb₂O₅. The only discontinuity was found for the temperature coefficient of resonant frequency, which is negative throughout the entire homogeneity range but reaches a minimum value for the sample with 20 mol% Nb₂O₅. At the same composition there is a discontinuity in the grain size of the δ-BN_ss ceramics. For the sample containing 25 mol% Nb₂O₅ two structural modifications were observed. A single-phase tetragonal Bi₃NbO₇, in the literature referred to as a Type-III phase, is formed in a very narrow temperature range from 850° to 880°C. A synthesis performed below or above this temperature range resulted in the formation of the end member of the δ-BN_ss homogeneity range. Compared with the δ-BN_ss the Bi₃NbO₇ ceramics exhibit lower microwave dielectric losses, an increased conductivity, and a positive temperature coefficient of resonant frequency.