水蒸气在中空纤维复合膜中渗透的微分阻力模型

建立了水蒸气在中空纤维复合膜中渗透的微分阻力模型,用实验验证了模型的可靠性。采用该模型估算出中空纤维膜的结构参数,研究了水蒸气在各层膜中的阻力,并以H2O/C2H2系统为例,考察了膜的结构参数对H2O/C2H2选择性的影响。     

Nanometric thin skinned dual‐layer hollow fiber membranes for dehydration of isopropanol

A novel sulfonated polyphenylsulfone (sPPSU)/polyphenylsulfone (PPSU)‐based dual‐layer hollow fiber membrane with a nanometric thin skin layer has been designed for biofuel dehydration via pervaporation. The thickness of skin selective layer is in the range of 15–90 nm under different spinning conditions measured by positron annihilation spectroscopy (PAS) coupled with a mono‐energetic positron beam. The effects of outer‐layer dope properties, coagulation temperature, and dope flow rate during spinning were systematically investigated. By tuning these spinning parameters, a high performance sPPSU/PPSU‐based dual‐layer hollow fiber membrane with desirable morphology was successfully obtained. Particularly owing to its nanometric thin skin layer, a high flux of 3.47 kg/m²h with a separation factor of 156 was achieved for dehydration of an 85 wt % isopropanol aqueous solution at 50°C. After post thermal treatment at 150°C for 2 h, the separation factor was dramatically improved to 687 while flux dropped to 2.30 kg/m²h, which make it comparable to the inorganic membranes. In addition, excellent correlations were found among the results from field emission scanning electron microscopy, PAS spectra, and separation performance. © 2013 American Institute of Chemical Engineers AIChE J, 59: 2943–2956, 2013     

Preparation and oxygen permeation of U‐shaped perovskite hollow‐fiber membranes

The oxygen permeation of dense U‐shaped perovskite hollow‐fiber membranes based on Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3?δ prepared by a phase inversion spinning process is reported. The perovskite hollow fibers with totally dense wall were obtained with the outer diameter of 1.147 mm and the inner diameter of 0.691 mm. The dependences of the oxygen permeation on the air flow rate on the shell side, the helium flow rate on the core side, the oxygen partial pressures, and the operating temperatures were experimentally investigated. According to the Wagner theory, it follows that the oxygen transport through the U‐shaped hollow‐fiber membrane is controlled by both surface reaction and bulk diffusion at the temperature ranges of 750–950°C. High oxygen permeation flux of 3.0 ml/(min cm²) was kept for about 250 h at 950°C under the conditions of the air feed flow rate of 150 ml/min and the helium flow rate of 50 ml/min. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

A rational asymmetric hollow fiber membrane for oxygen permeation

A typical oxygen permeation hollow fiber membrane fabricated by phase inversion-based extrusion process demonstrates heterogeneous porous microstructures, in which the surface layer with relatively low porosity is used as a separation layer after sintering. It is usually not convenient to control the thickness of separation layer. And a high sintering temperature is needed to densify the separation layer, which in turn could destroy the desired porous microstructures in other portion. This paper studies a novel process to fabricate multilayer asymmetric hollow fiber membrane with a rational design using 67 vol. % Gd_0.2Ce_0.8O_2−δ−33 vol. % La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (GDC-LSCF) as a model material system. The phase inversion-based extrusion process in open literature is employed to fabricate a hollow fiber substrate featuring radially well-aligned microchannels open at the inner surface. Built upon the hollow fiber substrate, a thin dense separation layer and porous surface catalyst layer at shell side are then fabricated through dip-coating and sintering process alternatively. The oxygen permeation flux of the fabricated hollow fiber membrane reaches 2.68 mL/cm²/min at 900°C under Ar/air gradient, the highest performance of the membranes with GDC-LSCF material system in open literature. The innovative fabrication process is able to readily control the thickness of functional layers while decreasing sintering temperatures.     

Multichannel mixed‐conducting hollow fiber membranes for oxygen separation

A multichannel mixed‐conducting hollow fiber (MMCHF) membrane, 0.5 wt % Nb₂O₅‐doped SrCo_0.8 Fe_0.2O_3‐δ (SCFNb), has been successfully prepared by phase inversion and sintering technique. The crystalline structure, morphology, sintering behavior, breaking load, and oxygen permeability of the MMCHF membrane were studied systematically. The MMCHF membrane with porous‐dense asymmetrical microstructure was obtained with the outer diameter of 2.46 mm and inner tetra‐bore diameter of 0.80 mm. The breaking load of the MMCHF membrane was 3–6 times that of conventional single‐channel mixed‐conducting hollow fiber membrane. The MMCHF membrane showed a high oxygen flux which was about two times that of symmetric capillary membrane at similar conditions as well as a good long‐term stability under low oxygen partial pressure atmosphere. This work proposed a new configuration for the mixed‐conducting membranes, combining advantages of multichannel tubular membrane technology and conventional hollow fibers. © 2014 American Institute of Chemical Engineers AIChE J, 60: 1969–1976, 2014     

Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes for pervaporation separation of ethanol/water solution

Polysulfone (PSF) hollow fiber membranes were spun by phase‐inversion method from 29 wt % solids of 29 : 65 : 6 PSF/NMP/glycerol and 29 : 64 : 7 PSF/DMAc/glycol using 93.5 : 6.5 NMP/water and 94.5 : 5.5 DMAc/water as bore fluids, respectively, while the external coagulant was water. Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes were prepared after PSF hollow fiber membranes were coated using different PVA aqueous solutions, which were composed of PVA, fatty alcohol polyoxyethylene ether (AEO₉), maleic acid (MAC), and water. Two coating methods (dip coating and vacuum coating) and different heat treatments were discussed. The effects of hollow fiber membrane treatment methods, membrane structures, ethanol solution temperatures, and MAC/PVA ratios on the pervaporation performance of 95 wt % ethanol/water solution were studied. Using the vacuum‐coating method, the suitable MAC/PVA ratio was 0.3 for the preparation of PVA/PSF hollow fiber composite membrane with the sponge‐like membrane structure. Its pervaporation performance was as follows: separation factor (α) was 185 while permeation flux (J) was 30g/m²·h at 50°C. Based on the experimental results, it was found that separation factor (α) of PVA/PSF composite membrane with single finger‐void membrane structure was higher than that with the sponge‐like membrane structure. Therefore, single finger‐void membrane structure as the supported membrane was more suitable than sponge‐like membrane structure for the preparation of PVA/PSF hollow fiber composite membrane. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 247–254, 2005     

Dual layer composite nanofiltration hollow fiber membranes for low-pressure water softening

Nanofiltration (NF) membrane process has become increasingly attractive due to their unique characteristics to selectively remove specific compounds or ions. The most commonly NF membranes are negatively charged which is unsuitable for hardness removal. Therefore, the development of novel NF membranes with a positively charged skin has become a key issue for low pressure water softening.     

Membrane‐assisted vapor stripping: energy efficient hybrid distillation–vapor permeation process for alcohol–water separation

BACKGROUND: Energy efficient alternatives to distillation for alcohol recovery from dilute solution are needed to improve biofuel sustainability. A process integrating steam stripping with a vapor compression step and a vapor permeation membrane separation step is proposed. The objective of this work is to estimate the energy and process costs required to make a fuel grade ethanol (0.5 wt% water) from 1 and 5 wt% ethanol aqueous streams using the proposed process. RESULTS: Using process simulation and spreadsheeting software, the proposed membrane‐assisted vapor stripping process was estimated to require as little as 8.9 MJ of fuel‐equivalent energy per kg of fuel grade ethanol recovered from a 1 wt% ethanol feed stream, 2.5 MJ kg^?1 for a 5 wt% ethanol solution. This represents an energy saving of at least 43% relative to standard distillation producing azeotropic ethanol (6 wt% water). Process costs were also found to be lower than for distillation at the 3.0 × 10⁶ kg‐ethanol year^?1 scale modeled. CONCLUSION: In this hybrid system, the stripping column provides high ethanol recoveries and low effluent concentrations while the vapor compression‐membrane component enables the efficient recovery of latent and sensible heat from both the retentate and permeate streams from the membrane system. Published in 2008 by John Wiley & Sons, Ltd.     

Dual‐layer PBI/P84 hollow fibers for pervaporation dehydration of acetone

Acetone dehydration via pervaporation is challenging, because acetone and water have close molecular sizes, and acetone has a much higher vapor pressure than water. Acetone is also a powerful solvent, which dissolves or swells most polymers. We have developed novel polybenzimidazole/BTDA‐TDI/MDI (PBI/P84) dual‐layer hollow fibers for pervaporation dehydration of acetone for industrial and biofuel separations. Both thermal and chemical crosslinking modifications were applied to the membranes to investigate their effectiveness to overcome acetone‐induced swelling. Thermal treatment can effectively enhance separation performance, but performance stability can only be achieved through the crosslinking modification of PBI. Crosslinking by p‐xylene dichloride followed by a thermal treatment above 250°C show significant effectiveness to improve and stabilize pervaporation performance. The fractional free volume of the PBI selective layer reduces from 3.27 to 1.98% and 1.33%, respectively, after thermal treatment and a combination of chemical/thermal crosslinking modifications characterized by positron annihilation spectroscopy. © 2011 American Institute of Chemical Engineers AIChE J, 2012     

Experimental validation of hybrid distillation‐vapor permeation process for energy efficient ethanol–water separation

BACKGROUND: The energy demand of distillation‐based systems for ethanol recovery and dehydration can be significant, particularly for dilute solutions. An alternative separation process integrating vapor stripping with a vapor compression step and a vapor permeation membrane separation step, termed membrane assisted vapor stripping (MAVS), has been proposed. The hydrophilic membrane separates the ethanol–water vapor into water‐rich permeate and ethanol‐enriched retentate vapor streams from which latent and sensible heat can be recovered. The objective of this work was to demonstrate experimentally the performance of a MAVS system and to compare the observed performance with chemical process simulation results using a 5 wt% ethanol aqueous feed stream as the benchmark. RESULTS: Performance of the steam stripping column alone was consistent with chemical process simulations of a stripping tower with six stages of vapor liquid equilibria (VLE). The overhead vapor from the stripper contained about 40 wt% ethanol and required 6.0 MJ of fuel‐equivalent energy per kg of ethanol recovered in the concentrate. Introduction of the vapor compressor and membrane separation unit and recovery of heat from both membrane permeate and retentate streams resulted in a retentate ethanol concentrate containing ca 80 wt% ethanol, but requiring only 2.2 MJ fuel kg^?1 ethanol, significantly less than steam stripping alone. CONCLUSION: Performance of the experimental unit with a 5 wt% ethanol feed liquid corroborated chemical process simulation predictions for the energy requirement of the MAVS system, demonstrating a 63% reduction in the fuel‐equivalent energy requirement for MAVS compared with conventional steam stripping or distillation. Published 2009 by John Wiley & Sons, Ltd.     

Modified poly(vinylidene fluoride) hollow fiber composite membranes reinforced by hydroxyapatite nanocrystal whiskers

The modified poly(vinylidene fluoride) (PVDF) hollow fiber composite membranes reinforced by hydroxyapatite (HAP) nanocrystal whiskers were fabricated with wet‐spinning method. The PVDF/HAP/N‐methyl‐2‐pyrrolidone dope solutions experienced delayed demixing mechanism, and the precipitation rate slightly increased as the HAP whisker content increased. The cross sections of PVDF‐HAP and neat PVDF hollow fiber composite membranes were composed of five distinct layers: two skin layers, two finger‐like sublayers, and a sponge‐like layer. The Young's modulus of and tensile strength of the PVDF‐HAP hollow fiber membranes gradually increased with the addition of nano‐HAP whiskers. The elongation ratio was also improved, which was different from the polymeric membranes modified by other inorganic nanofillers. The permeation flux of the PVDF‐HAP hollow fiber membranes slightly increased with the increase of HAP content in the composite membranes as its hydrophilicity was improved. The crystallization behaviors of PVDF in the composite membranes were also investigated. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Second interfacial polymerization of thin-film composite hollow fibers with amine-cyclodextrins for pervaporation dehydration

High performance thin-film composite (TFC) hollow fiber membranes have been developed for pervaporation dehydration by second interfacial polymerization (SIP) modification with three kinds of amine-functionalized β-cyclodextrin (amine-CDs), which were synthesized by modifying β-CD with ammonia, ethylenediamine (EDA), and tris(2-aminoethyl)amine, respectively. The chemical properties of amine-CDs and SIP-modified TFC membranes were characterized by various techniques. The effects of amine-CD type and SIP parameters (pH or concentration of CD-EDA solution) were studied systematically to acquire the optimized selective layer of TFC membranes for ethanol dehydration. Among all SIP-modified TFC membranes, the one with SIP by 2 wt% CD-EDA aqueous solution (pH = 2) exhibited the most outstanding separation performance with a ultrahigh permeation flux (3,018.0 ± 12.0 g/m² hr) and permeate concentration (98.7 ± 0.2 wt% water) at 50°C (equivalent to separation factor of 415), contributed by the effectively incorporated CD with rich hydrophilic functional groups and intrinsic nanocavities facilitating the passage of water molecules.     

A CO2‐stable hollow‐fiber membrane with high hydrogen permeation flux

A Mo‐substituted lanthanum tungstate mixed proton‐electron conductor, La_5.5W_0.6Mo_0.4O_11.25?δ (LWM04), was synthesized using solid state reactions. Dense U‐shaped LWM04 hollow‐fiber membranes were successfully prepared using wet‐spinning phase‐inversion and sintering. The stability of LWM04 in a CO₂‐containing atmosphere and the permeation of hydrogen through the LWM04 hollow‐fiber membrane were investigated in detail. A high hydrogen permeation flux of 1.36 mL/min cm² was obtained for the U‐shaped LWM04 hollow‐fiber membranes at 975°C when a mixture of 80% H₂?20% He was used as the feed gas and the sweep side was humidified. Moreover, the hydrogen permeation flux did not significantly decrease over 70 h of operation when fed with a mixture containing 25% CO₂, 50% H₂, and 25% He, indicating that the LWM04 hollow‐fiber membrane has good stability under a CO₂‐containing atmosphere. © 2015 American Institute of Chemical Engineers AIChE J, 61: 1997–2007, 2015     

Pushing the limits of high performance dual‐layer hollow fiber fabricated via I2PS process in dehydration of ethanol

The immiscibility induced phase separation (I²PS) process was introduced as a novel method to fabricate hollow fibers with exceptionally high water permeance and reasonably high water/ethanol selectivity in dehydration of ethanol by pervaporation. As a continuation of the previous work, this study discloses the mechanisms to enhance the performance of hollow fibers spun via I²PS by elucidating the material selection at the inner‐layer. Moreover, it revealed the methods to reduce mass‐transport resistance by enhancing surface porosity for both inner and outer surfaces to further improve the permeation flux of the membranes. The continuous performance test demonstrates that the fibers spun from the I²PS possess a stable dehydration performance throughout the monitored period of 300 h. A comparison with pervaporation membranes in the literatures verifies the superiority of the membranes spun via I²PS process with the highest water permeation flux of 9.5 kg/m² h and the permeate water purity of 95.8 wt % at 80°C. © 2013 American Institute of Chemical Engineers AIChE J, 59: 3006–3018, 2013     

Gas permeation performance of cellulose hollow fiber membranes made from the cellulose/N‐methylmorpholine‐N‐oxide/H2O system

Cellulose hollow fiber membranes (CHFM) were prepared using a spinning solution containing N‐methylmorpholine‐N‐oxide as solvent and water as a nonsolvent additive. Water was also used as both the internal and external coagulant. It was demonstrated that the phase separation mechanism of this system was delayed demixing. The CHFM was revealed to be homogeneously dense structure after desiccation. The gas permeation properties of CO₂, N₂, CH₄, and H₂ through CHFM were investigated as a function of membrane water content and operation pressure. The water content of CHFM had crucial influence on gas permeation performance, and the permeation rates of all gases increased sharply with the increase of membrane water content. The permeation rate of CO₂ increased with the increase of operation pressure, which has no significant effect on N₂, H₂, and CH₄. At the end of this article a detailed comparison of gas permeation performance and mechanism between the CHFM and cellulose acetate flat membrane was given. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1873–1880, 2004     

Highly scalable ZIF‐based mixed‐matrix hollow fiber membranes for advanced hydrocarbon separations

ZIF‐8/6FDA‐DAM, a proven mixed‐matrix material that demonstrated remarkably enhanced C₃H₆/C₃H₈ selectivity in dense film geometry, was extended to scalable hollow fiber geometry in the current work. We successfully formed dual‐layer ZIF‐8/6FDA‐DAM mixed‐matrix hollow fiber membranes with ZIF‐8 nanoparticle loading up to 30 wt % using the conventional dry‐jet/wet‐quench fiber spinning technique. The mixed‐matrix hollow fibers showed significantly enhanced C₃H₆/C₃H₈ selectivity that was consistent with mixed‐matrix dense films. Critical variables controlling successful formation of mixed‐matrix hollow fiber membranes with desirable morphology and attractive transport properties were discussed. Furthermore, the effects of coating materials on selectivity recovery of partially defective fibers were investigated. To our best knowledge, this is the first article reporting successful formation of high‐loading mixed‐matrix hollow fiber membranes with significantly enhanced selectivity for separation of condensable olefin/paraffin mixtures. Therefore, it represents a major step in the research area of advanced mixed‐matrix membranes. © 2014 American Institute of Chemical Engineers AIChE J, 60: 2625–2635, 2014