Ethylene polymerization over (nBuCp)2ZrCl2/MAO catalytic system supported on aluminosilicate SBA‐15 mesostructured materials

Heterogeneous metallocene catalysts were prepared by incipient wetness impregnation of AlSBA‐15 (Si/Al = 4.8, 15, 30, 60, and ∞) mesostructured materials with (nBuCp)₂ZrCl₂/MAO. For comparative purposes commercial silica and silica–alumina (Si/Al = 4.8) supports were also impregnated with the MAO/metallocene catalytic system. A combination of X‐ray powder diffraction, nitrogen adsorption–desorption isotherms at 77 K, transmission electron microscopy, ICP‐atomic emission spectroscopy, and UV–vis spectroscopic data, were used to characterize the supports and the heterogeneous catalysts. Ethylene polymerizations were carried out in a schlenk tube at 70 °C and 1.2 bar of ethylene pressure. The polyethylene obtained was characterized by GPC, DSC, and SEM. Catalysts prepared with mesostructured SBA‐15 supports exhibited better catalytic performance than those supported on amorphous silica and silica–alumina. In general, higher ethylene polymerization activity was achieved if (nBuCp)₂ ZrCl₂/MAO catalytic system was heterogenized using supports with lower pore size in the range of the mesopores and lower Si/Al ratio. All catalysts produced high‐density polyethylene, with high crystallinity values and fibrous morphology when SBA‐15 mesostructured materials were used as supports. POLYM. ENG SCI., 2008. © 2008 Society of Plastics Engineers     

Silica‐supported (nBuCp)2ZrCl2: effect of catalyst active center distribution on ethylene–1‐hexene copolymerization

Metallocenes are a modern innovation in polyolefin catalysis research. Therefore, two supported metallocene catalysts—silica/MAO/(ⁿBuCp)₂ZrCl₂ (Catalyst 1) and silica/ⁿBuSnCl₃/MAO/(ⁿBuCp)₂ZrCl₂ (Catalyst 2), where MAO is methylaluminoxane—were synthesized, and subsequently used to prepare, without separate feeding of MAO, ethylene–1‐hexene Copolymer 1 and Copolymer 2, respectively. Fouling‐free copolymerization, catalyst kinetic stability and production of free‐flowing polymer particles (replicating the catalyst particle size distribution) confirmed the occurrence of heterogeneous catalysis. The catalyst active center distribution was modeled by deconvoluting the measured molecular weight distribution and copolymer composition distribution. Five different active center types were predicted for each catalyst, which was corroborated by successive self‐nucleation and annealing experiments, as well as by an extended X‐ray absorption fine structure spectroscopy report published in the literature. Hence, metallocenes impregnated particularly on an MAO‐pretreated support may be rightly envisioned to comprise an ensemble of isolated single sites that have varying coordination environments. This study shows how the active center distribution and the design of supported MAO anions affect copolymerization activity, polymerization mechanism and the resulting polymer microstructures. Catalyst 2 showed less copolymerization activity than Catalyst 1. Strong chain transfer and positive co‐monomer effect—both by 1‐hexene—were common. Each copolymer demonstrated vinyl, vinylidene and trans‐vinylene end groups, and compositional heterogeneity. All these findings were explained, as appropriate, considering the modeled active center distribution, MAO cage structure repeat units, proposed catalyst surface chemistry, segregation effects and the literature that concerns and supports this study. While doing so, new insights were obtained. Additionally, future research, along the direction of the present work, is recommended. © 2013 Society of Chemical Industry     

Ethylene polymerization with methylaluminoxane/(nBuCp)2ZrCl2 catalyst supported on silica and silica‐alumina at different AlMAO/Zr molar ratios

Methylaluminoxane (MAO)/(nBuCp)₂ZrCl₂ metallocene catalytic system was supported on silica and silica‐alumina. The Zr loading was varied between 0.2–0.4 wt %, and the MAO amount was calculated to get (Al_MAO/Zr) molar ratios between 100 and 200, suitable for the industrial ethylene polymerization of supported metallocene catalysts. Catalytic activity was statistically analyzed through the response surface method. Within the ranges studied, it was found that Zr loading had a negative effect on polymerization activity, which increases with the (Al_MAO/Zr) molar ratio. Catalysts supported on silica‐alumina are more active than those supported on silica, needing less MAO to reach similar productivity, which constitutes an important advantage from an economical and environmental point of view. Supported catalysts were characterized by ICP‐AES, SEM‐energy‐dispersive X‐ray spectrometer, and UV‐Vis spectroscopy, whereas polyethylenes were characterized by GPC and DSC. Molecular weight and crystallinity are not influenced by Zr loading or (Al_MAO/Zr) ratio, in the range studied. In general, silica‐supported MAO/(nBuCp)₂ZrCl₂ catalysts give polyethylenes with higher molecular weight and polydispersity but lower crystallinity. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Immobilized Me2Si(C5Me4)(N‐tBu)TiCl2/(nBuCp)2ZrCl2 hybrid metallocene catalyst system for the production of poly(ethylene‐co‐hexene) with pseudo‐bimodal molecular weight and inverse comonomer distribution

Me₂Si(C₅Me₄)(N‐tBu)TiCl₂, (nBuCp)₂ZrCl₂, and Me₂Si(C₅Me₄)(N‐tBu)TiCl₂/(nBuCp)₂ZrCl₂ catalyst systems were successfully immobilized on silica and applied to ethylene/hexene copolymerization. In the presence of 20 mL of hexene and 25 mg of butyloctyl magnesium in 400 mL of isobutane at 40 bar of ethylene, Me₂Si(C₅Me₄)(N‐tBu)TiCl₂ immobilized catalyst afforded poly(ethylene‐co‐hexene) with high molecular weight ([η] = 12.41) and high comonomer content (%C₆ = 2.8%), while (nBuCp)₂ZrCl₂‐immobilized catalyst afforded polymers with relatively low molecular weight ([η] = 2.58) with low comonomer content (%C₆ = 0.9%). Immobilized Me₂Si(C₅Me₄)(N‐tBu)TiCl₂/(nBuCp)₂ZrCl₂ hybrid catalyst exhibited high and stable polymerization activity with time, affording polymers with pseudo‐bimodal molecular weight distribution and clear inverse comonomer distribution (low comonomer content for low molecular weight polymer fraction and vice versa). The polymerization characteristics and rate profiles suggest that individual catalysts in the hybrid catalyst system are independent of each other. POLYM. ENG. SCI., 47:131–139, 2007. © 2007 Society of Plastics Engineers     

Organic/inorganic support for immobilizing (n‐BuCp)2ZrCl2/TiCl3 hybrid catalyst for use in the preparation of polymer blends

Reactor blends of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and low‐molecular‐weight polyethylene (LMWPE) were synthesized by two‐step polymerization using a hybrid catalyst. To prepare the hybrid catalyst, styrene acrylic copolymer (PSA) was first coated onto SiO₂/MgCl₂‐supported TiCl₃; then, (n‐BuCp)₂ZrCl₂ was immobilized onto the exterior PSA. UHMWPE was produced in the first polymerization stage with the presence of 1‐hexene and modified methylaluminoxane (MMAO), and the LMWPE was prepared with the presence of hydrogen and triethylaluminium in the second polymerization stage. The activity of the hybrid catalyst was considerable (6.5 × 10⁶ g PE (mol Zr)^?1 h^?1), and was maintained for longer than 8 h during the two‐step polymerization. The barrier property of PSA to the co‐catalyst was verified using ethylene polymerization experiments. The appearance of a lag phase in the kinetic curve during the first‐stage polymerization implied that the exterior catalyst ((n‐BuCp)₂ZrCl₂) could be activated prior to the interior catalyst (M‐1). Furthermore, the melting temperature, crystallinity, degree of branching, molecular weight and molecular‐weight distribution of polyethylene obtained at various polymerization times showed that the M‐1 catalyst began to be activated by MMAO after 40 min of the reaction. The activation of M‐1 catalyst led to a decrease in the molecular weight of UHMWPE. Finally, the thermal behaviors of polyethylene blends were investigated using differential scanning calorimetry. Copyright © 2011 Society of Chemical Industry     

The effect of aluminum alkyls and BHT‐H on reaction kinetics of silica supported metallocenes and polymer properties in slurry phase ethylene polymerization

In slurry and gas phase catalytic ethylene polymerization processes, aluminum alkyl (AlR₃) compounds are usually present inside the reactor and their role either as co‐catalyst or scavenger is of considerable importance. Silica supported metallocene/methyl aluminoxane (MAO) catalysts show specific interactions with AlR₃ compounds. Therefore, this study shows an attempt to analyze and compare the effect of concentration as well as type of commonly used AlR₃ on slurry phase ethylene homopolymerization kinetics of silica supported (n‐BuCp)₂ZrCl₂/MAO catalyst. The obtained results indicate that the lower the concentration of smaller AlR₃ compounds, the higher the instantaneous catalytic activity. Concerning the polymer particle size distributions, a rise in fines generation has been observed with increasing AlR₃ content inside the reactor. Finally, it has been shown that the addition of 2,6‐di‐tert‐butyl‐4‐methylphenol (a substituted phenol) into the reactor containing AlR₃ reduces the influence of AlR₃ compounds on the reaction kinetics of silica supported metallocene/MAO catalysts. Polyethylene properties remain similar in all the studied scenarios. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45670.     

Supported SiO2‐nBuSnCl3/MAO/(nBuCp)2ZrCl2 catalyzing MAO cocatalyst‐free ethylene polymerization: Study of hydrogen responsiveness

A supported metallocene catalyst was synthesized by sequentially loading methylaluminoxane (MAO) (30 wt % in toluene) and (ⁿBuCp)₂ZrCl₂ on partially dehydroxylated silica ES 70 modified by ⁿBuSnCl₃. Its shock load hydrogen responsiveness was evaluated by polymerizing ethylene for 1 h at 8.5 bar (g) and 75°C without separately feeding the MAO cocatalyst. The shock load hydrogen feeding increased the ethylene consumption (at a fairly constant rate), catalyst productivity, as well as the resin bulk density and average particle size at ΔP (of hydrogen) ≥～3.0 psi. The bulk density increased from 0.25 to 0.31 g/cm³. This shows a procedure for overcoming the inherent drop in catalyst productivity caused by heterogenization of metallocenes (that is a method for catalyst activation) and improving the resulting resin bulk density. The volume‐weighted mean particle diameter of the resulting polyethylenes was found to be 5.80–11.12‐fold that of the catalyst corresponding to ΔP = 0.00–7.11 psi, respectively. The resulting kinetic profiles showed to be fairly stable. However, M_w and polydispersity index were not affected. The particle size distribution, average particle size, and the scanning electron microscope photographs of the resulting resin particles confirmed the occurrence of the replication phenomenon. On the basis of the above findings, the mechanism of ethylene polymerization under the present experimental conditions has been revisited. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

In situ copolymerization of ethylene to produce linear low‐density polyethylene by Ti(OBu)4/AlEt3‐MAO/SiO2/Et(Ind)2ZrCl2

Linear low‐density polyethylene (LLDPE) is produced in a reactor from single ethylene feed by combining Ti(OBu)₄/AlEt₃, capable of forming α‐olefins (predominantly 1‐butene), with SiO₂‐supported Et(Ind)₂ZrCl₂ (denoted MAO/SiO₂/Et(Ind)₂ZrCl₂), which is able to copolymerize ethylene and 1‐butene in situ with little interference in the dual‐functional catalytic system. The two catalysts in the dual‐functional catalytic system match well because of the employment of triethylaluminum (AlEt₃) as the single cocatalyst to both Ti(OBu)₄ and MAO/SiO₂/Et(Ind)₂ZrCl₂, exhibiting high polymerization activity and improved properties of the obtained polyethylene. There is a noticeable increment in catalytic activity when the amount of Ti(OBu)₄ in the reactor increases and 1‐butene can be incorporated by about 6.51 mol % in the backbone of polyethylene chains at the highest Ti(OBu)₄ concentration in the feed. The molecular weights (M_w), melting points, and crystallinity of the LLDPE descend as the amount of Ti(OBu)₄ decreases, which is attributed mainly to chain termination and high branching degree, while the molecular weight distribution remains within a narrow range as in the case of metallocene catalysts. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2451–2455, 2004     

Preparation of ethylene/1‐octene copolymers from ethylene stock with tandem catalytic system

Tandem catalysis offers a novel synthetic route to the production of linear low‐density polyethylene. This article reports the use of homogeneous tandem catalytic systems for the synthesis of ethylene/1‐octene copolymers from ethylene stock as the sole monomer. The reported catalytic systems involving a highly selective, bis(diphenylphosphino)cyclohexylamine/Cr(acac)₃/methylaluminoxane (MAO) catalytic systems for the synthesis of 1‐hexene and 1‐octene, and a copolymerization metallocene catalyst, rac‐Et(Ind)₂ZrCl₂/MAO for the synthesis of ethylene/1‐octene copolymer. Analysis by means of DSC, GPC, and ¹³C‐NMR suggests that copolymers of 1‐hexene and ethylene and copolymers of 1‐octene and ethylene are produced with significant selectivity towards 1‐hexene and 1‐octene as comonomers incorporated into the polymer backbone respectively. We have demonstrated that, by the simple manipulation of the catalyst molar ratio and polymerization conditions, a series of branched polyethylenes with melting temperatures of 101.1–134.1°C and density of 0.922–0.950 g cm^?3 can be efficiently produced. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Long Chain Branched Polypropene Prepared by Means of Propene Copolymerization with 1,7‐Octadiene Using MAO‐Activated rac‐Me2Si(2‐Me‐4‐Phenyl‐Ind)2ZrCl2

Small amounts of 1,7‐octadiene (OD) comonomer, ranging from 0.5–5.0 mol‐%, were added during propene polymerization, catalyzed with methylalumoxane (MAO) activated rac‐Me₂Si(2‐Me‐4‐phenyl‐Ind)₂ZrCl₂ (MPI), in order to incorporate long chain branches and small amounts of high molecular mass polypropene (PP), thus improving melt processability of isotactic metallocene‐polypropene. As a function of the OD content the PP melting temperatures varied from 120 to 160°C. The presence of long chain branches was reflected by increased zero shear viscosities combined with pronounced shear thinning behavior in the case of propene/OD copolymers with molecular mass distribution of M̄_w/M̄_n < 4. Rheological measurements clearly revealed crosslinking occurring at high OD content. OD addition impaired catalyst activities. However, in the presence of trace amounts of ethene, catalyst activities increased significantly even in the presence of high OD content.     

Organic Nanoparticles with Polypropyleneoxide Chains as Support for Metallocene Catalysts: Ethylene Homopolymerization and Ethylene/α-olefin Copolymerization

Summary Novel organic nanoparticles functionalized with nucleophilic polypropyleneoxide (PPO) chains on their surfaces for supporting metallocene catalysts in heterogeneous olefin polymerization are presented. The nanoparticles (60–100 nm) were obtained by miniemulsion polymerization of styrene, divinylbenzene and PPO functionalized styrene. It is demonstrated that Me₂Si(2MeBenzlnd)₂ZrCl₂/MAO supported on these nanoparticles is suitable for the homopolymerization of ethylene, resulting in excellent product morphologies and high activities. lt is shown that by varying the MAO/Zr ratios and Zr concentrations the activities and productivities of the catalysts as well as the qualities of the polyethylene products can be tuned. These new supported catalysts are also suitable for the copolymerization of ethylene with several comonomers (1-hexene, 1-octene, 1-decene or norbornene). As the obtained product properties like crystallinity, melting temperature or bulk density match the results of silica supported systems, these organic nanoparticles can be considered as alternative carriers in comparison to the established inorganic ones.     

The investigation of novel non‐metallocene catalysts with phenoxy‐imine ligands for ethylene (co‐)polymerization

Phthaldialdehyde and phthaldiketone were treated with substituted phenols of 2‐amino‐4‐methylphenol, 2‐amino‐5‐methylphenol and 2‐amino‐4‐t‐butylphenol, respectively, and then treated with transition metal halides of TiCl₄, ZrCl₄ and YCl₃. A series of novel non‐metallocene catalysts (1–12) with phenoxy‐imine ligands was obtained. The structures and properties of the catalysts were characterized by ¹H NMR and elemental analysis. The catalysts (1–12) were used to promote ethylene (co‐)polymerization after activation by methylaluminoxane. The effects of the structures and center atoms (Ti, Zr and Y) of these catalysts, polymerization temperature, Al/M (M = Ti, Zr and Y) molar ratio, concentration of the catalysts and solvents on the polymerization performance were investigated. The results showed that the catalysts were favorable for ethylene homopolymerization and copolymerization of ethylene with 1‐hexene. Catalyst 10 is most favorable for catalyzing ethylene homopolymerization and copolymerization of ethylene with 1‐hexene, with catalytic activity up to 2.93 × 10⁶ gPE (mol Y)^?1 h^?1 for polyethylene (PE) and 2.96 × 10⁶ gPE (mol Y)^?1 h^?1 for copolymerization of ethylene with 1‐hexene under the following conditions: polymerization temperature 50 °C, Al/Y molar ratio 300, concentration of catalyst 1.0 × 10^?4 L^?1 and toluene as solvent. The structures and properties of the polymers obtained were characterized by Fourier transform infrared spectroscopy, ¹³C NMR, wide‐angle X‐ray diffraction, gel permeation chromatography and DSC. The results indicated that the obtained PE catalyzed by 4 had the highest melting point of 134.8 °C and the highest weight‐average molecular weight of 7.48 × 10⁵ g mol^?1. The copolymer catalyzed by 4 had the highest incorporation of 1‐hexene, up to 5.26 mol%, into the copolymer chain. © 2012 Society of Chemical Industry     

Ethylene polymerization by phenylenedimethylene‐bridged homobinuclear zirconocene/methylaluminoxane systems

In the presence of methylaluminoxane (MAO), ethylene polymerization was successfully performed with homobinuclear zirconocene complexes {[(C₅H₅)ZrCl₂](C₅H₄CH₂ C₆H₄CH₂C₅H₄)[(C₅H₅)ZrCl₂]; 3o , 4m , and 5p }, which were prepared conveniently by the reaction of disodium(phenylenedimethylene)dicyclopentadienide [C₆H₄(CH₂C₅H₄Na)₂] with 2 equiv of (N⁵‐Cyclopentadienyl)trichlorozirconium dimethoxyethane (CpZrCl₃(DME)) in tetrahydrofuran and characterized by ¹H‐NMR and elemental analysis. The effects of the polymerization parameters, such as the temperature, time, concentration of the catalyst, MAO/catalyst molar ratio, and isomeric difference of the homobinuclear metallocene complexes 3o , 4m , and 5p were studied in detail. The results showed that all three catalytic systems had moderate activities in ethylene polymerization and afforded polyethylene with relatively broad polydispersities. The catalytic activity of 4m was somewhat higher than that of 3o and 5p but lower than that of 4,4′‐bis(methylene)biphenylene‐bridged zirconocene catalysts; this indicated that the distance between the two metal centers was too short in comparison with a 4,4′‐bis(methylene)biphenylene bridge to increase the catalytic activity. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Copolymerization and characterization of ethene–1‐hexene copolymers prepared by using the (Me5Cp)2ZrCl2–MAO catalyst system

It is demonstrated that the catalyst system bis(pentamethylcyclopentadienyl)‐zirconium dichloride (Me₅Cp)₂ZrCl₂–methylaluminoxane (MAO) is able to produce random copolymers of ethene and 1‐hexene. The 1‐hexene incorporation in the copolymers is extremely small. Even in the case of a molar ratio of [ethene] to [1‐hexene] of 1/20 in the monomer feed, only 1.4 mol % 1‐hexene are incorporated according to ¹³C nuclear magnetic resonance (NMR) spectra. Nevertheless, the physical properties of the random copolymers change significantly in this small range of 1‐hexene incorporation, from a high‐density polyethene to a linear low‐density polyethene. Thus, the melting temperature, the degree of crystallinity, the density and lamella thickness, and the long period of the alternating crystalline and amorphous regions decrease with increasing 1‐hexene content in the random copolymers. Blends of high‐density polyethene prepared with the system (Me₅Cp)₂ZrCl₂–MAO and an elastomeric random copolymer of ethene and 1‐hexene are phase‐separated and show good compatibility, as demonstrated by transmission electron microscopy. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 439–447, 1999     

Functionalization of polyethylene using borane reagents and metallocene catalysts

A new method to prepare functionalized polyethylene involving borane intermediates and transition metal catalysts is described. Two processes, direct and post polymerizations, were employed to prepare borane-containing polyethylene (PE-B), which can be transformed to functionalized polyethylene (LLDPE-f) with various functional groups, such as ? BR₂, ? OH, ? NH₂, ? OSi(CH₃)₃. In the direct process, the PE-B copolymers were prepared in one step by copolymerization of ethylene with a borane monomer (ω-borane-α-olefin). The post polymerization process requires two steps: copolymerization of ethylene and 1,4-hexadiene, and subsequential hydroboration reaction of unsaturated PE. Three transition metal catalysts, including two homogeneous metallocene (Cp₂ZrCl₂ [bis(cyclopentadienyl) zirconium dichloride] and Et(Ind)₂ZrCl₂ [1,1′-ethylenedi-η⁵-indenyl-zirconium dichloride] with MAO (methylaluminoxane)) and one heterogeneous (TiCl₃·AA/Et₂AlCl) ones, were studied in the copolymerization reactions. The single site Et(Ind)₂ZrCl₂/MAO homogeneous catalyst, with a strained ligand geometry and opened active site, is by far the most effective system in the incorporation of high olefins into polyethylene structures.     

Copolymerization of propylene and norbornene with different metallocene catalysts

Propylene and norbornene were copolymerized by metallocene/MAO catalysts. The organometallic compounds rac-[Me₂C(Ind)₂]ZrCl₂ (1) and [Me₂C(Cp)(Flu)]ZrCl₂ (2), [Ph₂C(Cp)(2,7-di^tBuFlu)]ZrCl₂ (3) and [Me₂Si(3-^tBuCp)(N^tBu)]TiCl₂ (4) were used to catalyze polymerization series, in which the influence of the molar fraction of norbornene in the feed and of the polymerization temperature were investigated in detail. The obtained polymers, which exhibit a wide range of properties with glass transition temperatures above 200 °C, were characterized by ¹³C NMR spectroscopy, differential scanning calorimetry and gel permeation chromatography techniques.In this article, the emphasis is placed on the copolymerization behaviour of the catalysts and the properties of the obtained polymers, while other articles concentrate on NMR investigations of propylene/norbornene copolymers.     

Ethylene/propylene copolymerization over three conventional C2‐symmetric metallocene catalysts: Correlation between catalyst configuration and copolymer microstructure

This work reports on a correlation between catalyst configuration and copolymer microstructure for ethylene/propylene (E/P) copolymerization using three conventional C₂‐symmetric metallocene catalysts, namely, rac‐Et(Ind)₂ZrCl₂ (EBI), rac‐Me₂Si(2‐Me‐4‐Ph‐Ind)₂ZrCl₂ (SiPh), and rac‐CH₂(3‐tBu‐Ind)₂ZrCl₂ (MBu), with MAO as a common cocatalyst. Copolymerization reactions were conducted in toluene at three different temperatures with varied E/P ratios. Some typically obtained copolymers were characterized in detail using ¹³C‐NMR spectroscopy, by which triad distribution data were elaborated in a statistical method to determine the reactivity ratios (r_E and r_P) of the comonomers, which were also obtained by Fineman‐Rose estimation. The production of alternating‐like copolymers from EBI is attributed to the rapid interconversion between two conformation states of the active site, one of which favors the incorporation of propylene but the other one does not. Both SiPh and MBu are structurally more rigid and of larger dihedral angles than EBI; however, SiPh which owns open active site conformation tend to produce random copolymers at all studied temperatures, and for MBu, sterically hindered catalyst, block‐like copolymers were obtained. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of aluminum alkyls on ethylene/1‐hexene polymerization with supported metallocene/MAO catalysts in the gas phase

The effects of aluminum alkyls on the gas‐phase ethylene homopolymerization and ethylene/1‐hexene copolymerization over polymer‐supported metallocene/methylaluminoxane [(n‐BuCp)₂ZrCl₂/MAO] catalysts were investigated. Results with triisobutyl aluminum (TIBA), triethyl aluminum (TEA), and tri‐n‐octyl aluminum (TNOA) showed that both the type and the amount of aluminum alkyl influenced the polymerization activity profiles and to a lesser extent the polymer molar masses. The response to aluminum alkyls depended on the morphology and the Al : Zr ratio of the catalyst. Addition of TIBA and TEA to supported catalysts with Al : Zr >200 reduced the initial activity but at times resulted in higher average activities due to broadening of the kinetic profiles, i.e., alkyls can be used to control the shape of the activity profiles. A catalyst with Al : Zr = 110 exhibited relatively low activity when the amount of TIBA added was <0.4 mmol, but the activity increased fivefold by increasing the TIBA amount to 0.6 mmol. The effectiveness of the aluminum alkyls in inhibiting the initial polymerization activity is in the following order: TEA > TIBA >> TNOA. A 2‐L semibatch reactor, typically run at 80°C and 1.4 MPa ethylene pressure for 1 to 5 h was used for the gas‐phase polymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3549–3560, 2004     

Development of novel chromium oxide/metallocene hybrid catalysts for bimodal polyethylene

The investigation of a multicomponent catalyst in polyolefin field came up as an alternative for synthesizing bimodal polymers in only one step process under constant reaction conditions.In the present work, new bifunctional catalysts were prepared by combining chromium and metallocene species on the same solid and tested in ethylene polymerization in order to evaluate the possibility of producing bimodal polyethylene. The catalytic system methylaluminoxane (MAO)/(nBuCp)₂ZrCl₂ was immobilized on activated chromium catalysts supported onto several inorganic carriers (silica, silica-alumina, aluminophosphate and mesostructured SBA-15-type materials). The reaction results showed a clear influence of the physicochemical properties of the support on the relative contribution of metallocene and chromium centers as well as on polymers molecular weight distribution. A bimodal polyethylene was obtained by supporting the MAO/metallocene system on a mesostructured chromium catalyst prepared by direct synthesis.     

Synthesis of pentavalent imidovanadium complexes and their catalyses for the polymerization of ethylene and propylene

Imidovanadium complexes with cyclopentadienyl (Cp) ligands—(Cp)V(?NC₆H₄Me‐4)Cl₂ (1), (Cp)V(?N^tBu)Cl₂ (2), and (^tBuCp)V(?N^tBu)Cl₂ (3; ^tBuCp = tert‐butylcyclopentadienyl)—were synthesized through the reaction of imidovanadium trichloride with (trimethylsilyl)cyclopentadiene derivatives. The molecular structure of 3 was determined by X‐ray crystallography. The monocyclopentadienyl complex 1 exhibited moderate activity in combination with methylaluminoxane [MAO; 10.3 kg of polyethylene (mol of V)^?1 h^?1 atm^?1], whereas similar complexes with bulky ^tBu groups, 2 and 3, were less active. (2‐Methyl‐8‐quinolinolato)imidovanadium complexes, V(?NR)(O ?N)Cl₂ (R = C₆H₃ⁱPr₂‐2,6 (4) or n‐hexyl (5), O ?N = 2‐methyl‐8‐quinolinolato), were obtained from the reaction of imidovanadium trichloride with 2‐methyl‐8‐quinolinol. Upon activation with modified MAO, complex 4 showed moderate activities for the polymerization of ethylene at room temperature. The complex 5/MAO system also exhibited moderate activity at 0°C. The polyethylenes obtained by these complexes had considerably high melting points, which indicated the formation of linear polyethylene. Moreover, the 5/dried MAO system showed propylene polymerization activities and produced polymers with considerably high molecular weights and narrow molecular weight distributions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1008–1015, 2005