Study on physical properties of blend films from gelatin and polyacrylamide solutions

Blend films of gelatin and polyacrylamide (PAAm) were prepared by casting the mixed aqueous solutions of both samples in different ratios. All blend films obtained are optically clear to the naked eye. The structure and physical properties of the films were studied by FT‐infrared (FTIR), wide‐angle X‐ray diffraction (WAXD), differential thermal analysis (DTA), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The experimental results show that the blend films exhibit the higher thermal stability and improved mechanical properties of both tensile strength and elongation at break in dry states, which suggests the occurrence of interaction detected by FTIR between gelatin, PAAm, and water molecules in the films. The morphological transition of the blend films from gelatin‐like to PAAm‐like was observed by SEM. Furthermore, moisture content and water swelling property of the blend films were also investigated, which was consistent with the results from SEM. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 949–955, 2002     

Deduction of a facile method to construct Antheraea mylitta silk fibroin/gelatin blend films for prospective biomedical applications

Blend films of two types (I and II) were prepared by mixing Antheraea mylitta silk fibroin (AMF) and gelatin solution in various blend ratios via the solution casting method. Two different crosslinkers, namely glutaraldehyde and genipin, were used during blend preparation. The structural characteristics and thermal properties of the blend films were examined by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), Thermogravimetric analysis (TGA) and Diffrential scanning calorimetery (DSC). The FTIR spectra showed conformational alterations in type I blend films while type II films attained high β‐sheet crystallinity. The XRD diffractograms presented a high degree of crystallinity in type II blend films compared to type I, which showed an almost amorphous structure. Further, thermal and biological studies were conducted on type II films. According to the TGA thermograms, the degradation temperature of the crosslinked blend films shifted compared to pure gelatin and pure AMF films. Partial miscibility of the two components was indicated by DSC thermograms of the blends. The high water uptake capacity of type II blend films was found to imitate hydrogel behaviour. The blend films did not show any toxicity in 3‐(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) assay and supported L929 fibroblast cell spreading and proliferation. The biodegradation of the blend films was significantly faster than the pure silk film. © 2020 Society of Industrial Chemistry     

Preparation and Characterization of Gelatin-Based PVA Film: Effect of Gamma Irradiation

Gelatin-based polyvinyl alcohol (PVA) films were prepared (using a casting process) by mixing aqueous solutions of gelatin and PVA in different ratios. Monomer 1, 4-butanediol diacrylate (BDDA) was dissolved in methanol. Films containing 95% gelatin + 5% PVA were soaked in 3% BDDA monomer (w/w). These films were then irradiated under gamma radiation (⁶⁰Co) at different doses (50–500 krad) at a dose rate of 350 krad/h. The physico-mechanical and thermal properties of these films were evaluated. It was evident that 5% PVA-containing gelatin blend film exhibited the highest tensile strength (TS) value at 50 krad (51 MPa), which was 46% higher than that of non-irradiated blend films. It was also found that incorporation of PVA significantly reduced the TS value of the blend films compared to the raw film, whereas elongation at break (Eb) value was increased. A significant improvement of the blend films was also confirmed by thermogravimetric analysis (TGA) and thermo-mechanical analysis (TMA) when the acrylate group (from BDDA) was introduced into the film.     

Effect of glycerol on structure–property relations in chitosan/poly(ethylene oxide) blended films investigated using wide‐angle X‐ray diffraction

Polymer blending is an effective method for providing desirable polymeric materials with properties useful for the packaging industry. In the study reported, blends of chitosan/poly(ethylene oxide) (PEO) were prepared in various weight ratios with and without glycerol. Line profile analysis of the X‐ray diffraction patterns of these blended films was carried out. Microstructural parameters such as crystallite size and lattice strain were determined using paracrystalline modelling of X‐ray data. These values were correlated with physico‐mechanical and optical properties of the chitosan/PEO blends with and without glycerol to understand the holistic behaviour of the blends. Two prominent Bragg reflections at 2θ ≈ 19° and 23° were observed in the wide‐angle X‐ray diffraction patterns of the glycerol‐based chitosan/PEO blended films of various ratios. Interruption of PEO crystallization with chitosan results in an amorphous polymer network and hence a reduction in crystallite size by almost 97.7%. For glycerol‐based blends, the crystallite size/area decreases to 94.4% of the virgin crystallite size. The X‐ray profile analysis supports the results for the physico‐mechanical properties of the blends. The results show that the addition of 20 wt% of glycerol results in an increase of the elongation at break by more than 150%, meaning that these chitosan/PEO films could be applied in flexible packaging. Copyright © 2010 Society of Chemical Industry     

Preparation and characterization of biocompatible poly(L‐lactic acid)/gelatin blend membrane

Poly(L ‐lactic acid) (PLLA)/gelatin blend membranes were prepared by solution casting method and using dimethyl sulfoxide (DMSO) as a cosolvent. Scanning electron microscopy measurement indicated that when the amounts of gelatin in PLLA/gelatin blend membranes are less than 5%, the sizes of phase separation of gelatin are in range of several hundred nanometers. These benefit in retaining the strength of PLLA membranes. X‐ray diffraction analysis revealed that the semicrystalline PLLA became amorphous and the melt temperature of crystalline PLLA changes from 56 to 38°C after it was processed in DMSO solvent. When the content of gelatin is less than 5%, the films not only retain a good mechanical property but also improve the hydrophilicity of PLLA. The molecular motion of PLLA in blend films were also investigated by solid state ¹³C CP/MAS NMR. On the basis of the result of relaxation times, it was found that the molecular motion of PLLA100 and PLLA/gelatin blends increased when compared with that of original PLLA. It was further verified that semicrystalline PLLA became amorphous. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 269–276, 2006     

In situ fibrillar reinforced PET/PA‐6/PA‐66 blend

Ternary fibrillar reinforced blends are obtained by melt‐blending of poly(ethylene terephthalate) (PET), polyamide 6 (PA‐6) and polyamide 66 (PA‐66) (20/60/20 by weight) in the presence of a catalyst, followed by cold drawing of the extruded bristles to a draw ratio of about 3.4 and additional annealing of the drawn blend at 220 or 240°C for 4 or 8 h. The blend samples are studied by DSC, X‐ray diffraction, SEM, and static and dynamic mechanical testing (DMA). SEM and DMA show that PA‐6 and PA‐66 form a homogeneous, continuous matrix in which PET regions are dispersed. X‐ray and DSC measurements of the drawn and annealed at 220°C samples suggest mixed crystallization (solid solubility) of PA‐6 and PA‐66, and cooperative crystallization of PET with the two polyamides. After annealing at 240°C (above the melting point of PA‐6 and below that of PET), the polyamide matrix becomes partially disoriented, while the oriented, fibrillar PET is preserved and plays the role of a reinforcing element. The DSC results for the same samples suggest in situ generation of an additional amount of copolymer. This additional copolymerization, together with that generated during blend mixing in the extruder, improves the compatibility of the blend components (mostly at the PET‐polyamide interface) and alters the chemical composition of the blend.     

Studies of chitosan. I. Preparation and characterization of chitosan/poly(vinyl alcohol) blend films

Various blending ratios of chitosan/poly (vinyl alcohol) (CS/PVA) blend films were prepared by solution blend method in this study. The thermal properties and chemical structure characterization of the CS/PVA blend films were examined by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and Fourier transform infrared (FTIR). Based upon the observation on the DSC thermal analysis, the melting point of PVA is decreased when the amount of CS in the blend film is increased. The FTIR absorption characteristic is changed when the amount of CS in the blend film is varied. Results of X‐ray diffraction (XRD) analysis indicate that the intensity of diffraction peak at 19° of PVA becomes lower and broader with increasing the amount of CS in the CS/PVA blend film. This trend illustrates that the existence of CS decreases the crystallinity of PVA. Although both PVA and CS are hydrophilic biodegradable polymers, the results of water contact angle measurement are still shown as high as 68° and 83° for PVA and for CS films, respectively. A minimum water contact angle (56°) was observed when the blend film contains 50 wt % CS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Development of a gel spinning process for high‐strength poly(ethylene oxide) fibers

This article describes a new gel‐spinning process for making high‐strength poly(ethylene oxide) (PEO) fibers. The PEO gel‐spinning process was enabled through an oligomer/polymer blend in place of conventional organic solvents, and the gelation and solvent‐like properties were investigated. A 92/8 wt% poly(ethylene glycol)/PEO gel exhibited a melting temperature around 45°C and was highly stretchable at room temperature. Some salient features of a gel‐spun PEO fiber with a draw ratio of 60 are tensile strength at break = 0.66 ± 0.04 GPa, Young's modulus = 4.3 ± 0.1 GPa, and a toughness corresponding to 117 MJ/m³. These numbers are significantly higher than those previously reported. Wide‐angle x‐ray diffraction of the high‐strength fibers showed good molecular orientation along the fiber direction. The results also demonstrate the potential of further improvement of mechanical properties. POLYM. ENG. SCI., 54:2839–2847, 2014. © 2014 Society of Plastics Engineers     

Characterization of polyvinyl alcohol/gelatin blend hydrogel films for biomedical applications

In the present investigation, attempt was made to prepare blend hydrogel by esterification of polyvinyl alcohol with gelatin. The blend hydrogel was further converted into films by the conventional solution‐casting method. These films were characterized by FTIR, DSC, and X‐ray diffraction studies. The refractive index and viscosity of different composition of the blends were measured in the solution phase of the material. The mechanical properties of the blend films were measured by tensile test. Swelling behavior of the blend hydrogel was also studied. The FTIR spectrum of the blend film indicated complete esterification of the free carboxylic group of gelatin. The DSC results indicate that the addition of gelatin with PVA changes the thermal behavior like melting temperature of PVA, which may be due to the miscibility of PVA with gelatin. The interaction of gelatin with PVA molecule changes the crystallite parameters and the degree of crystallinity. The crystallinity of the blend film was mainly due to gelatin. The comparison of viscosity indicated an increase in the segment density within the molecular coil. The results revealed the changes observed in the properties of the gel, and it enhances the gel formation at viscoelastic phase of the material. The blend film had sufficient strength and water‐holding capacity. The results obtained indicated that the blend film could be used for various biomedical applications such as wound dressing and drug‐delivery systems. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Blend films from chitosan and konjac glucomannan solutions

Blend films were prepared by blending 7 wt % konjac glucomannan (KGM) aqueous solution with 2 wt % chitosan (CH) in acetate solution and dried at 40°C for 4 h to obtain the transparent films. Their structure and properties were studied by infrared (IR), wide‐angle X‐ray diffraction (WAXD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). Crystallinities of the blend films decreased with the increase of konjac glucomannan. The thermostability, tensile strength, and breaking elongation of the blend films in dry state were obviously higher than those of both konjac glucomannan and chitosan films. Tensile strength of the dry blend film achieved 73.0MPa when the weight ratio of chitosan to konjac glucomannan was 7:3. The structure analysis indicated that there is a strong interaction between konjac glucomannan and chitosan resulted from intermolecular hydrogen bonds. The water solubility of the blend films was improved by blending with konjac glucomannan, so they have promising applications to soluble antiseptic coating of pills. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 509–515, 2000     

Casting solvent effect on crystallization behavior and morphology of poly(ethylene oxide)/poly(methyl methacrylate)

Poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) blends were prepared by casting from either chloroform or benzene solvents. After casting from solvents, all samples used in this study were preheated to 100°C and held for 10 min. Then, the solvent effect on the crystallization behavior and thermodynamic properties were studied by differential scanning calorimeter (DSC). Also, the morphology of spherulite of casting film was studied by polarized optical microscope. From the DSC and polarizing optical microscopy (POM) results, it was found that PEO/PMMA was miscible in the molten state no matter which casting solvent was used. However, the crystallization of PEO in the chloroform‐cast blend was more easily suppressed than it was in the benzene‐cast blend. Relatively, the chloroform‐cast blend showed the greater melting‐point depressing of PEO crystals. Also, the spherulite of chloroform‐cast film showed a coarser birefringence. It was supposed that the chloroform‐cast blend had more homogeneous morphology. It is fair to say that polymer blends, cast from solvent, are not necessarily in equilibrium. However, the benzene‐cast blends still were not in equilibrium even after preheating at 100°C for 10 min. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1627–1636, 2000     

Synthesis and characterization of ethylene vinyl‐acetate/polyaniline blends prepared by emulsion polymerization technique

A series of ethylene vinyl acetate‐polyaniline (98/02, 95/05, 93/07, … … 50/50) (EVA‐PAni) blends were prepared by the emulsion polymerization technique and made into sheets by the compression molding at 150°C. These sheets were characterized by electrical, physico‐mechanical, thermal, X‐ray and morphological studies. All electrical properties of EVA‐(PAni)_TSA blends increased with an increase in PAni content. The conductivity, dielectric constant and tan δ values increased from 1.34 × 10^?14 to 2.89 × 10^?2 S/cm, from 2.113 to 19.845, from 0.094 to 4.789. Tensile strength increased with an increase in PAni content up to 7% and drastically decreased above 15%, while the percentage elongation at break decreased with an increase in PAni content. TGA studies revealed that the thermal stability of PAni improved after blending with EVA. EVA‐PAni blends were found stable up to 110°C. X‐ray diffractograms of EVA‐PAni blend showed an intense peak at 26° (2θ), reflecting the influence of EVA crystallinity. Scanning electron micrographs confirmed the two‐phase morphology of the system.     

Structural and dielectric studies of amorphous and semicrystalline polymers blend‐based nanocomposite electrolytes

The solid polymeric nanocomposite electrolyte (SPNE) films based on the blend of amorphous poly(methyl methacrylate) (PMMA) and semicrystalline poly(ethylene oxide) (PEO) (PMMA:PEO = 80:20 wt %) doped with lithium perchlorate (LiClO₄) salt and montmorillonite (MMT) clay nanofiller were prepared by classical solution cast, ultrasonic assisted solution cast and ultrasonication along with microwave irradiated solution cast followed by melt‐pressing methods. The X‐ray diffraction study of these electrolytes revealed the amorphous behavior with intercalated MMT structures. The suppressed crystallinity of PEO in the blend electrolyte complexes confirmed the existence of single discrete PEO chains confined within the PMMA domains. The dielectric relaxation spectroscopy of these materials was performed over the frequency range 20 Hz to 1 MHz, at ambient temperature. The presence of a singular relaxation peak in the loss tangent and electric modulus spectra of these electrolytes confirms a coupled cooperative chain segmental dynamics of the blend polymer owing to their miscible amorphous morphology. The behavior of transient complexes formed between the polymers functional groups, lithium cations and the intercalated MMT nanoplatelets was explored. The ambient temperature ionic conductivity of these electrolytes depends on the structural dynamics and the sample preparation methods. It is revealed that the presence of PEO in the PMMA matrix mainly governs the structural, dielectric, and ionic properties of these SPNE films. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41311.     

Evaluation of the microstructure and melting behavior of drawn polypropylene fibers with a microthermal analyzer

The strong correlation of melting behavior with the microstructure of original and zone‐drawn isotactic polypropylene fibers was evaluated by microthermal analysis (micro‐TA) combined with wide‐angle X‐ray diffraction analysis. The crystal structure of both the original and zone‐drawn fibers was a monoclinic α‐form with a ～ 0.64 nm, b ～ 2.03 nm, and c ～ 0.65 nm. In contrast to the absence of any oriented polymer molecules in the original fiber, the polymer molecules in the zone‐drawn fiber were extended and highly oriented in at least two different states; one arranged along the drawn axis and the other at 40° to the drawn axis. The micro‐TA‐derived melting points corresponded to these microstructural changes caused by the zone‐drawing process and differed from the melting points obtained by differential scanning calorimetery. The micro‐TA melting point of 140°C corresponded to the z‐e‐p melting point of the original fiber, being much lower than the conventional differential scanning calorimetery melting point of 163°C. As for the zone‐drawn fiber, an increase of 19°C in the melting temperature revealed its high orientation level, and the appearance of three elevated melting peaks (161, 167, and 178°C) at the highest heating rate (1500°C/min) coincided with its several oriented states. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1306–1311, 2006     

Crystallization behavior and mechanical properties of poly(ethylene oxide)/poly(L‐lactide)/poly(vinyl acetate) blends

Poly(vinyl acetate) (PVAc) was added to the crystalline blends of poly(ethylene oxide) (PEO) and poly(L ‐lactide) (PLLA) (40/60) of higher molecular weights, whereas diblock and triblock poly(ethylene glycol)–poly(L ‐lactide) copolymers were added to the same blend of moderate molecular weights. The crystallization rate of PLLA of the blend containing PVAc was reduced, as evidenced by X‐ray diffraction measurement. A ringed spherulite morphology of PLLA was observed in the PEO/PLLA/PVAc blend, attributed to the presence of twisted lamellae, and the morphology was affected by the amount of PVAc. A steady increase in the elongation at break in the solution blend with an increase in the PVAc content was observed. The melting behavior of PLLA and PEO in the PEO/PLLA/block copolymer blends was not greatly affected by the block copolymer, and the average size of the dispersed PEO domain was not significantly changed by the block copolymer. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3618–3626, 2001     

Morphology,drug release behavior,thermal, and mechanical properties of poly(ethylene oxide) (PEO)/poly(vinyl pyrrolidone) (PVP) blends

Poly(ethylene oxide) (PEO)/poly(vinyl pyrrolidone) (PVP) blends containing different amounts of PVP (0, 10, 25, 50, and 100 wt %) prepared by a solution casting method were characterized in terms of microstructure, thermal, and mechanical properties along with their drug release behavior. Fourier‐transform infrared spectroscopy results confirmed formation of hydrogen bonds between PEO and PVP. Although scanning electron microscopy micrographs showed no phase separation in the blends, the elemental analysis data obtained by energy dispersive X‐ray technique revealed partial miscibility between the blend components. The miscibility of the blend and degree of crystallinity of PEO component of the blend were decreased with increasing PVP content of the blend. The nucleating role of PVP in crystallization of PEO was confirmed by differential scanning calorimetry analysis. A synergistic effect on mechanical properties was obtained as a result of blending PVP with PEO. The results of curcumin release studies from the films indicated that, the blends have lower diffusion coefficients and slower drug release rate as compared to the neat PEO. Theoretical analysis of the drug release data using Peppas's model revealed that the kinetic of drug release from all the films is governed by a non‐Fickian diffusion mechanism. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46403.     

Effects of Temperature on Morphology and Properties of Films Prepared from Poly(ester‐urethane) and Nitrochitosan

Summary: Novel elastic materials were prepared by mixing semicrystalline polyester‐based polyurethane (PU) synthesized at 100 °C with nitrochitosan (NCH) and 1,1,1‐tris(hydroxylmethyl)propane as crosslinker, and then by curing the mixture at 18, 25, 40, 60, and 80 °C. The effects of cure temperature on the crystallization behavior, miscibility, and mechanical properties of the PUNCH materials were studied by attenuated total reflection Fourier transform IR, wide‐angle X‐ray diffraction, scanning electron microscopy, dynamic mechanical analysis, X‐ray photoelectron spectroscopy, and tensile test. The results indicated that the crystalline structure of the blend films was more easily interrupted as the cure temperature increased, leading to a decrease of the degree of crystallinity. With an increase of cure temperature, the blend films exhibited high crosslinking density and tensile strength, and the phase separation between hard and soft segments of PU enhanced, resulting in a decrease in the glass transition temperature (T_g) of soft segment. Interestingly, the composite films keeping high elongation at break possessed tensile strength higher than that of the native poly(ester‐urethane). The enhanced mechanical properties of the blend films can be attributed to the relatively dense crosslinking network and strong intermolecular hydrogen bonding between NCH and PU. Therefore, this study not only provided a novel way by adding NCH into PU matrix to prepare elastic materials, which would remain functional characteristic of chitosan, but also expanded the application field of chitosan.

The cure temperature dependence of the tensile strength and elongation at break for the PEPU‐100 and PUNCH‐100 films.     

Characterization of konjac glucomannan–gelatin blend films

Novel blend films of konjac glucomannan (KGM) with gelatin were prepared by using the solvent‐casting technique. Transparent blend films were obtained in all blending ratios of the two polymers. The structure and physical properties of the films were investigated by Fourier transform IR, wide angle X‐ray diffraction, thermogravimetric analysis, differential thermal analysis, scanning electron microscopy (SEM), and strength tests. The results indicated that intermolecular interactions between the KGM and gelatin occurred that were caused by hydrogen bonding and the physical properties of the films largely depended on the blending ratio. The crystallinities of the blend films decreased with the increase of the KGM. The thermal stability and mechanical properties (tensile strength and elongation at break) of the films were improved by blending KGM with gelatin. It is worth noting that the blend films had a good tensile strength of 38 MPa when the KGM content in the blend films was around 30 wt %. The surface morphology of the blend films observed by SEM displayed a certain level of miscibility. Furthermore, the water absorbability of the blend films was also measured and discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1596–1602, 2001     

Structure and properties of ultraviolet‐irradiated high density polyethylene at different environmental temperatures

C? O, C?O, and C(?O)O oxygen‐containing groups were introduced onto the molecular chain of high‐density polyethylene (HDPE) through ultraviolet irradiation in air. The introduction rate of the oxygen‐containing groups onto HDPE increased with increasing environmental temperature. After ultraviolet irradiation, the molecular weight of HDPE decreased, and its distribution became wider; the melting temperature, contact angle with water, and impact strength decreased; the degree of crystallinity and yield strength increased; and their variation amplitude increased with environmental temperature. The environmental temperature had an effect on the gel content of irradiated HDPE. HDPE‐irradiated for 48 h at 35° and 50°C were not crosslinked. However, gelation took place in HDPE irradiated for 24 h at 70°C. HDPE irradiated at a high environmental temperature was more effective than that irradiated at a low environmental temperature in compatibilizing HDPE with PVA. Compared with the 83/17 HDPE/PVA blend, the yield and notched impact strength of the 73/17 HDPE/PVA blend compatibilized with 10% HDPE irradiated for 24 h at an environmental temperature of 70°C increased from 30.8 MPa and 110 J/m to 34.9 MPa and 142 J/m, respectively. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2966–2969, 2003     

γ射线辐照对PVAL/Gel共混膜拉伸性能的影响

将明胶(Gel)按不同比例加入到聚乙烯醇(PVAL)溶液中,制备Gel质量分数分别为0%,5%,10%,15%和20%的混合溶液,混合均匀后分别浇铸到用硅纸覆盖的玻璃板上制备PVAL/Gel共混膜。研究了用不同剂量的γ射线(60Co)辐照对共混膜拉伸性能的影响,最后用傅立叶变换红外光谱(FTIR)和扫描电子显微镜(SEM)对共混膜进行了结构表征和形貌分析。研究结果表明,用γ射线辐照时,纯PVAL膜、PVAL/Gel共混膜的拉伸强度和断裂伸长率均随着辐照剂量的增加而升高,但达到一定值后又开始下降;当辐照剂量为150 krad时,纯PVAL膜的拉伸强度达到最大值,为37 MPa;当辐照剂量为50 krad时,Gel质量分数分别为5%,10%,15%的共混膜的拉伸强度值均有极大值,分别为33,26,24 MPa。当辐照剂量为100 krad时,共混膜的断裂伸长率均有极大值,其中纯PVAL膜、Gel质量分数为10%的共混膜的断裂伸长率分别为175%,162%。FTIR和SEM分析结果表明,γ射线辐照处理后的膜发生了化学反应,形成了更多的化学键,改善了膜的拉伸性能。